Sub Controller

(Interface Unit)

RS-422A

Sub Controller

(Interface Unit)

RS-422A

: Standard units making up Sony router system

(M) and (S) mean the setting of M/S switch on the CPU board.

(M) (S) : M/S switch setting on the monitor Board.

: T Bridge (A)

: T Bridge (B)

: 75 ZTerminator

BKS-R3209

BKS-R3209

Primary station (DVS-V3232B/V6464B, HDS-V3232)

8 groups

Remote control unit

No. 1

No. 2

No. 3

No. 4

No. 8

1group : 160 names

No. 2 group

No. 2 group

No. 4 group

1 group for each unit

Routing Switcher

(4 : 2 : 2)

Net group

System Status Screen

[Ctrl] - [X] [Ctrl] - [X]

Menu Screen

*1 [Ctrl] - [E]

Setting Screen

Setting of the primary station

Menu Screen

*1 [Ctrl] - [E]

Setting Screen

Setting of the secondary station on monitor S-BUS

Setting Screen

Setting of the primary station on monitor S-BUS

Menu Screen of the Primary Station (Ex. DVS-V6464B)

n

. Menu screen of BKDF-R70 does not have the menu item [S].

. Menu screen of HDS-V3232 does not have the menu item [S] and [Y].

Station address

Menu item

Short-cut key

BVS-A3232

Fig. 1

4-4. Basic Setup Procedures

Name Types

SDI

Routing

Switcher

AES/EBU

Routing

Switcher

Analog

Routing

Switcher

Physical Inputs

VTR 1

VTR 2

VTR 3

VTR 4

VTR 5

VTR 6

VTR 7

VTR 8

Studio A

News 1

Satelite 1

Satelite 2

Network 1

Network 2

Remote 1

Remote 2

Camera 1

Camera 2

Camera 3

Camera 4

Still Store 1

Still Store 2

Char Gen 1

Char Gen 2

Frame Sync 1

Frame Sync 2

Studio B

Patch

Patch

Patch

Patch

A/D #1

VTR 1

VTR 2

VTR 3

VTR 4

VTR 5

VTR 6

VTR 7

VTR 8

DAT 1

DAT 2

DAT 3

A/D #1

A/D #2

Mixer 1 PGM

Mixer 1 Aux

SDI Demux Out

VTR 1

VTR 2

VTR 3

VTR 4

VTR 5

VTR 6

VTR 7

VTR 8

Mixer 2 PGM Out

News 1

Satelite 1

Satelite 2

Network 1

Network 2

Remote 1

Remote 2

SDI

Routing

Switcher

AES/EBU

Routing

Switcher

Analog

Routing

Switcher

DAT 1

DAT 2

Level 1 (SDI)DAT 3

D/A #1

D/A #2

Mixer 1 In 1

Mixer 1 In 2

SDI Mux In

A/D #1

A/D #2

Fig. 7

4-4. Basic Setup Procedures

VTR 001

VTR 002

VTR 003

VTR 004

VTR 005

VTR 006

VTR 007

VTR 008

STU 111

NEWS 001

SAT 001

SAT 002

NET 101

NET 102

REM 101

REM 102

CAM 001

CAM 002

CAM 003

CAM 004

SS 001

SS 002

CG 001

CG 002

FS 001

FS 002

STU 121

PTCH 001

PTCH 002

PTCH 003

PTCH 004

DIG 101

DAT 001

DAT 002

DAT 003

DIG 201

DIG 202

MIX 201

MIX 202

DIG 203

VTR 001

VTR 002

VTR 003

VTR 004

VTR 005

VTR 006

VTR 007

VTR 008

SAT 001

SAT 002

REM 001

NET 001

NEWS 001

NEWS 002

CG 001

CG 002

CAM 001

CAM 002

CAM 003

CAM 004

STU 111

STU 112

MON 111

MON 112

SS 001

SS 002

NEWS103

STU 121

STU 122

FS 001

FS 002

DIG 101

DAT 001

DAT 002

DAT 003

DIG 201

DIG 202

MIX 201

MIX 202

DIG 203

DIG 301

DIG 302

This menu is used to set the type name of the source destination and global phantom table.

The menu makes the management of source/destination easier.

Setting Procedure

1.Select menu item [B].

2.Use the cursor or alphabet/numerical keys and select the codes for the type name to be registered from the sixteen character codes (0 to 9 and A to F) displayed on the screen.

3.When [Ctrl] _[P] is pressed, the setting of the type

name will be canceled, and ??? ?? ?? ?? ?? ??? will be displayed.

4.When [Enter] is pressed, the type name can be set. If [Enter] is pressed again before entering the type

name, the registration will be deleted and the cursor moves to the next position.

5.Use the alphabet and numerical keys to enter the type name (within four letters).

6.When [Enter] is pressed, the type name will be set

and the cursor moves to the next position.

If [Ctrl] _[F] is pressed before the setting, the original type name will be returned.

7.When [Ctrl] _[E] is pressed, the menu screen will be displayed.

Ctrl-E:RETURN TO MENU???

???

Example of Setting Screen

This menu is used to set the destination name and protect function of each output.

A number between 001 to 999 and a type name set at the menu item [B : SET SOURCE/DEST TYPE] can be set to each destination. Description name can be set by chang- ing the name mode at the menu item [J : NAME STYLE]. For details of setting the name, refer to [J] in the menu. The protect function (to protect the output signal from being controlled from the remote control unit) prevents the source signal selected for the specified destination from being switched by other remote control units.

(During recording and ON AIR, interrupting operations can be prevented.)

Setting Procedure (Destination Name)

1.Select menu item [C].

2.Press the cursor keys or the function keys to select the destination number.

3.When [Ctrl] _[P] is pressed, the set destination name will be deleted and ??? ?? ?? ?? ?? ??? will be displayed.

4.When [Enter] is pressed, the destination name can be

typed.

If [Enter] is pressed again before entering a name, the registration will be deleted and the cursor moves to the next position.

5.Select the code assigned to each type name, and use the numerical keys to enter the destination name.

6.When [Enter] is pressed, the destination name will be

set and the cursor moves to the next position. If [Ctrl] _[F] is pressed before the setting, the

original destination name will be returned.

7.When [Ctrl] _[E] is pressed, the menu screen will be displayed.

n

1.The same destination name cannot be registered at more than two destinations. If this is done, an error message will be displayed at the bottom of the screen.

Example: ??? VTR001 is used already; Ignored???

destination name

2.When the Description name mode is selected at menu item [J], both Description name and ???Type +number??? name will be displayed.

In this menu, Description name is used for setting.

Setting Procedure (Protect Function)

1.Select the destination name using the cursor, and then press [P]. ???P??? is displayed after the selected destina-

tion name and the protect function is set.

Protect function cannot be set for a number whose destination name has not been assigned.

2.To release the protect function, select the destination name and press [P] once again.

m

1.If a destination name is reversed, it means the protect function is set with a control terminal and not with a remote control unit.

2.To change the protected destination name, release the protection first before beginning the modification process.

Example of Setting Screen

Operating Function Keys

[F1] : SEARCH (To move the cursor to the desired destination name)

1.When [F1] is pressed, ???Please Input DEST. NAME =??? will be displayed.

2.Input the destination name to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired destination name.

n

When menu item [J] is set to the Description name mode, [F1] (SEARCH) will have the following functions.

1.When [F1] is pressed, ???Please Input NAME =???will be displayed.

2.Enter the Description name (within seven characters) from the head.

3.When [Enter] is pressed, the Description name entered will be searched.

4.If the desired name does not exist in the screen, press [F1] again.

[F2] : JUMP (To move the cursor to the destination number)

1.When [F2] is pressed, ???Please Input DEST NUMBER =??? will be displayed.

2.Input the destination number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : Pg Up

When [F3] is pressed, the screen will display the 16

lines previous to the 16 lines displayed currently. [F4] : Pg Dn

When [F4] is pressed, the screen will display the 16 lines next to the 16 lines displayed currently.

D : SET SOURCE NAME

Purpose

This menu is used to set the source name and secret function (inhibition of source selection with a remote control unit).

A number between 001 to 999 and a type name set at the menu item [B : SET SOURCE/DEST TYPE] can be set to each source name. Description name can be set by changing the name mode at menu item [J : NAME STYLE] in the menu. For details of setting the name, refer to [J] in the menu.

The secret function is necessary when a source signal should not be taken. When secret is set, remote control units cannot select the source signal.

Setting Procedure (Source Name)

1.Select menu item [D].

2.Press the cursor keys or the function keys, to select the source number.

3.When [Ctrl] _[P] is pressed, the source name will be deleted.

4.When [Enter] is pressed, the source name can be typed. If [Enter] is pressed before entering a name,

the registration will be deleted and the cursor moves to the next position.

5.Select the code assigned to each type name, and use the numerical keys to enter the source name.

6.When [Enter] is pressed, the source name will be set

and the cursor moves to the next position.

If [Ctrl] _[F] is pressed before the setting, the original source name will be returned.

7.When [Ctrl] _[E] is pressed, the menu screen will be displayed.

n

1.The same name cannot be given to assigned to two or more sources. If this is done, an error message will be displayed at the bottom of the screen.

Example: ??? VTR001 is used already; Ignored???

source name

2.When the Description name is selected at menu item [J], the screen will display the Description name in addition to the ???Type +Number??? name.

In this menu, the Description name is used for settings.

Setting Procedure (Secret Function)

1.Select the source name using the cursor, and press [S]. ???S??? is displayed after the source name, and the secret

is set. Secret cannot be set for a number whose source name has not been assigned.

2.To release the secret function, select the source name and press [S] once again.

When the password is required, input the password and press [Enter]. The secret will be released.

n

For details on password settings, refer to the menu item [P

: CHANGE PASSWORD].

Example of Setting Screen

E : SET LEVEL TABLE

Purpose

This menu is used to assign the level name and the level to each destination name. Up to eight levels can be set.

In this menu, set only the necessary levels. If levels which have not actually been used are set, the response of the routing switcher system will become slower. Delete all levels not needed.

After setting this menu item, the selected levels can be checked by remote control unit.

Setting Procedure (Setting of Level Names)

1.Select menu item [E].

2.Press the cursor keys or the function keys to select the level number 1 to 8.

3.When [Enter] is pressed, the level name can be assigned.

4.Enter the level name using the alphabet and numerical keys (within four characters).

5.When [Enter] is pressed, the level name will be set. If [Ctrl] _[F] is pressed before the setting, the

original level name will be returned.

6.When [Ctrl] _[Z] is pressed, the level 1 to 8 will be assigned to all destination names.

7.When [Ctrl] _[E] is pressed, the menu screen will be returned.

Setting Procedure (Level Setting .Release)

1.Select menu item [E].

2.Use the cursor keys to select the destination level.

3.When [Enter] is pressed, the level name will be

deleted and displayed as ??? ?? ?? ?? ?? ??? and the level setting will be released.

4.You can search the level with the function keys.

Example of Setting Screen

Operating Function Keys

[F1] : SEARCH (To move the cursor to the desired destination name)

1.When [F1] is pressed, ???Please Input DEST NAME =??? will be displayed.

2.Input the destination name to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired destination name.

n

When menu item [J] is set to the Description name mode, [F1] (SEARCH) will have the following functions.

1.When [F1] is pressed, ???Please Input NAME =??? will be displayed.

2.Enter the Description name (within seven characters) from the head.

3.When [Enter] is pressed, the Description name entered will be searched.

4.If the desired name does not exist in the screen, press [F1] again.

[F2] : JUMP (To move the cursor to the number of the desired destination)

1.When [F2] is pressed, ???Please Input DEST NUMBER =???, will be displayed.

2.Input the destination number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired destination number.

n

If the destination name is not set, the number of the destination will not be displayed.

F : SET ACTIVE UNIT NUMBER

Purpose

This menu is used to enable the units connected to the S- BUS data link to communicate.

Setting Procedure

1.Select menu item [F].

2.Press the cursor keys to select the secondary station whose communication will be valid.

3.When [Enter] is pressed, the setting displayed will change (???E??? ??? blank ??? ???E???). Only the secondary

stations displayed with ???E??? are valid. (???M??? indicates the primary station.)

4.When [Ctrl] _[E] is pressed, the menu screen will be displayed.

n

As the response will become slower if there are many secondary stations, make the secondary stations not connected invalid.

??? *??? indicates out of the control area.

ENABLE ACTIVE UNIT FOR STATION NUMBER DVS-V6464B V2.10 STATION NUMBER 1???

???

Ctrl-E:RETURN TO MENU

Example of Setting Screen

m

1.Station ID of the primary station is always regardless of the DIP switch setting on the CPU board.

2.Station ID of the secondary station is deter mined with the DIP switch setting. Do not assign the same number on two or more units as station ID on both standard S-BUS and monitor S-BUS.

Number that can be registered as secondary station ID are 2 to 254.

5-1. Setting Items of the Primary Station

G: UPDATE BACKUP CONTROLLER

Purpose

This menu is used to copy the table data stored in the main CPU board of the primary station to the backup CPU board.

This setting is valid only when the backup CPU board is installed in the primary station.

Setting Procedure

1.Select menu item [G]. The message ???This process requires about n minutes. Execute? (y/n)??? will be displayed at the bottom of the screen.

Ver. 2.00 : n=5

Ver. 1.00 : n=7

2.Table data copying is performed when [Y] is pressed. To cancel copying, press [N].

3.After copying, ???PROGRAM TABLE? (y/n)??? may be

displayed at the bottom of the screen. In this case, press [Y].

m

1.The ROM version of the main CPU board and that of the backup CPU board must be the same. If different versions are used, the unit may hang up due to copy- ing. Remove the backup CPU board when this occurs. The above occurs because a new table data can not be run on the old version software.

2.It takes about seven minutes to copy the table data. The copy makes other operations slow.

3.The table data of transcode from RS-422A to S-BUS (set at the menu item [U] of a secondary station) is not copied to the backup CPU board.

4.When you copy the data of main CPU to backup CPU on the menu screen [G : UPDATE BACKUP CON-

TROLLER] of the primary station or a secondary station, you can abort the operation by pressing [Ctrl]

_[D].

However you should copy again for the data of the backup CPU is not correct if aborted. Even if you do not copy again, the data will be renewed in one hour approximately by the auto backup function.

H : SET GLOBAL PHANTOM

The phantom function switches several crosspoints together with one button pushing of a remote control unit. The crosspoints of different levels can be also switched with this function.

There are two kinds of phantoms such as local phantom and global phantom (refer to the menu item [H : SET PHANTOM TABLE] of secondary stations for local phantom).

In local phantom function, the phantom data is stored in a remote control unit, and the phantom name is assigned only on this remote control unit. In global phantom function, however, the phantom data is stored in the primary station, and it can be called by any remote control unit. The global phantom function can be set only when DVS-V3232B/V6464B, BKPF-R70 or HDS-V3232 is assigned as the primary station.

The following describes how to set the global phantom data in the primary station. A maximum of 4095 cross- points can be registered.

Setting Procedure

1.Select menu item [H]. The global phantom list will be displayed.

2.Select any global phantom number with the cursor or function key and press [Enter]. The edit screen will

be displayed.

When [Ctrl] _[E] is pressed, the menu screen will be displayed.

Example of Global Phantom Screen

Operating Function Keys

(Global Phantom Display)

[F1] : SEARCH (To move the cursor to the desired global phantom name)

1.When [F1] is pressed, ???Please Input PHAN- TOM NAME =??? will be displayed.

2.Input the global phantom name to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired name.

[F2] : JUMP (To move the cursor to the desired global phantom number)

1.When [F2] is pressed, ???Please Input PHAN- TOM NAME =??? will be displayed.

2.Input the global phantom to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : Pg Up

When [F3] is pressed, the screen will display the 16

lines previous to the 16 lines displayed currently. [F4] : Pg Dn

When [F4] is pressed, the screen will display the 16 lines next to the 16 lines displayed currently.

3.As the cursor is placed where the name is typed, press [Enter]. The input mode will be set.

4.Select the codes assigned to each type name and enter any number using the cursor. Press [Enter] key to set it. Press [Ctrl] _[P] to delete the phantom name.

5.Move the cursor to the place to input the destination and press [Enter]. The input mode will be set.

6.Input the destination name with the alphabet or numerical keys and press [Enter] to set it.

7.Input the source name in the same way as setting the destination name and press [Enter].

8.Set the crosspoint level. Move the cursor to desired level and press [Enter]. The setting will be

changed.

Press [Ctrl] _[E]. The menu will return.

Example of Global Phantom Edit Screen

Operating Function Keys

(Global Phantom Edit Display)

[F1] : SEARCH (To move the cursor to any source name or destination name)

n

When menu item [J] is set to the Description name mode, [F1] (SEARCH) will have the following functions.

1.When [F1] is pressed, ???Please Input NAME =??? will be displayed.

2.Enter the Description name (within seven characters) from the head.

3.When [Enter] is pressed, the Description name entered will be searched.

4.If the desired name does not exist in the screen, press [F1] again.

[F2] : ADD (To add the row of crosspoints to be regis- tered as the global phantom)

[F3] : DELETE (To delete the crosspoints)

1.Select the destination name to be deleted using the cursor.

2.Press [F3].

[F4] : Dstlvl (To change the level of the crosspoint at the cursor to the level set at the menu item [E])

1.Select the destination name to be returned to the initial level using the cursor.

2.Press [F4].

n

When the name mode of menu item [J] is switched, the destination and source names displayed on the global phantom edit screen will change.

J : NAME STYLE

Purpose

This menu is used to switch the name styles of the destina- tion and source.

The ???Type +Number??? name (Type +Num) or ???Descrip- tion??? name (DESCRIP. NAME) can be set.

Names on the setting screen of menu items [C], [D], [E], [H], [L], [M], [N], [O], and [Q] are switched according to this menu.

Setting Procedure

1.Select menu item [J].

2.Press the alphabet key [J] and [Enter]. The message on the screen will change from ???Type +Num??? to ???DESCRIP. NAME??? each time this key are pressed.

.Destination name setting procedure using the Description name

3.Set menu item [J] to the Description name mode. Ex. [J : NAME STYLE (DESCRIP. NAME)]

4.Select menu item [C].

5.Move the cursor to the desired destination number.

6.When either [Enter] is pressed, the destination name

can be typed. If the Description name is set already, delete it by [BS].

7.Enter the Description name using the alphabet keys or the numerical keys. When [Enter] is pressed, the

Description name will be set. n

Up to sixteen characters can be input. Remote control units except BKS-R3281 will display until the seven characters. As the first seven characters are also used to distinguish the names, the unit may not operate properly if the same names are assigned for the first seven characters.

Example of Destination Name Setting Screen

Operating Function Keys

[F1] : SEARCH (To move the cursor to the desired destination name)

1.When [F1] is pressed, ???Please Input DEST NAME =??? will be displayed.

2.Input the destination name to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired destination name.

[F2] : JUMP (To move the cursor to the desired destina- tion number)

1.When [F2] is pressed, ???Please Input DEST NAME =??? will be displayed.

2.Input the destination number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : Pg Up

When [F3] is pressed, the screen will display the 16

lines previous to the 16 lines displayed currently. [F4] : Pg Dn

When [F4] is pressed, the screen will display the 16 lines next to the 16 lines displayed currently.

[F5] : PASTE (To copy the Description name)

1.Move the cursor to the destination number to be copied.

2.Press [SPACE].

3.Move the cursor to the destination number to be pasted, and press [F5].

n

Do not assign the same name to more than one destination.

.Source name setting procedure using Description name

3.Set menu item [J] to the Description name mode. Example:[J : NAME STYLE (DESCRIP. NAME)]

4.Select menu item [D].

5.Move the cursor to the desired source name.

6.When [Enter] is pressed, the Description name can be

typed. If the Description name is set already, delete it by [BS].

7.Enter the Description name using the alphabet or numerical keys. When [Enter] is pressed, the De-

scription name will be set.

K : RESET TO DEFAULT TABLE

K : DEFAULT TABLE

Purpose

This menu is used to initialize the table data. Do not perform this menu when modifying the table data.

Setting Procedure

1.Select menu item [K]. The message ???RESET TO DEFAULT TABLE? (y/n)??? will be displayed at the bottom of the screen.

2.Initialization is performed when [Y] is pressed. To cancel initializing, press [N].

n

The table data will be lost when performing the menu item [K].

5-1. Setting Items of the Primary Station

L : SET PHYSICAL ASSIGNMENT

Purpose

Assign the physical numbers of the switcher to the destina- tion numbers, source numbers and the levels of the virtual matrix.

Do not assign the same number.

Setting Procedure

1.Select menu item [L].

2.Each time [F5] is pressed, the setting screen will

change as follows.

Source number setting screen ??? destination number setting screen ??? source number setting screen.

.Source Number Setting Procedure

3.Select the source number setting screen.

4.Select the physical number and the level using the

cursor, and assign them to desired source number and level on the virtual matrix. When [Enter] is pressed,

the physical assignment can be typed.

5.Enter the physical number using numerical keys, and press [Enter].

6.Next, enter the physical level, and press [Enter] to set

it.

If press [Ctrl] _[F] before setting, the physical number and level will be returned to the previous values.

If the physical number and physical level to be set has been already used, cancel their settings first before setting new ones.

To cancel, select the physical number and level to be canceled, and press [Ctrl] _[P].

. Destination Number Setting Procedure

Press [F5] to set the destination number setting screen. Then, perform the same procedure as for source.

Example of Setting Screen

Operating Function Keys

[F1] : SEARCH {To move the cursor to the desired destination (source) name}

1.When [F1] is pressed, ???Please Input DEST (SOURCE) NAME =??? will be displayed.

2.Input the destination (source) name to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired name.

n

When menu item [J] is set to the Description name mode, [F1] (SEARCH) will have the following functions.

1.When [F1] is pressed, ???Please Input NAME =??? will be displayed.

2.Enter the Description name (within seven characters) from the head.

3.When [Enter] is pressed, the Description name entered will be searched.

4.If the desired name does not exist in the screen, press [F1] again.

[F2] : JUMP {To move the cursor to the desired destina- tion (source) number}

1.When [F2] is pressed, ???Please Input DEST (SOURCE) NUMBER=??? will be displayed.

2.Input the destination (source) number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : Pg Up

When [F3] is pressed, the screen will display the 16

lines previous to the 16 lines displayed currently. [F4] : Pg Dn

When [F4] is pressed, the screen will display the 16 lines next to the 16 lines displayed currently.

[F5] : SOURCE (DEST.)

When [F5] is pressed, the number setting screen will change between the destination number setting screen and source number setting screen alternately.

m

1.The physical number is the input/output number specified at the menu item [A : SET UNIT LOCA- TION].

2.The virtual input/output name and the virtual level name are assigned to the buttons on the remote control unit.

M: SET INHIBIT TABLE

Purpose

This menu is used to protect source numbers not to be selected for each destination.

When the secret function is set to a source name, the selected source cannot be output to all destinations. By using this menu, source numbers to be inhibited can be assigned for each destination.

Setting Procedure

1.Select menu item [M].

2.Select the source number for each destination name using the cursor. When [Enter] is pressed, the setting

will be switched.

???x??? : Connectable crosspoint

???_??? : Unconnectable crosspoint

Example of Setting Screen

n

The setting area for this menu is 512 x512. Set this function (crosspoint disable setting function) within the size specified for the system used.

Excess crosspoints will be ignored automatically.

Operating Function Keys

[F1] : SEARCH (To move the cursor to the desired destination name)

1.When [F1] is pressed, ???Please Input DEST NAME =??? will be displayed.

2.Input the destination name to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired name.

n

When menu item [J] is set to the Description name mode, [F1] (SEARCH) will have the following functions.

1.When [F1] is pressed, ???Please Input NAME =??? will be displayed.

2.Enter the Description name (within seven characters) from the head.

3.When [Enter] is pressed, the Description name entered will be searched.

4.If the desired name does not exist in the screen, press [F1] again.

[F2] : JUMP (To move the cursor to the desired destina- tion number)

1.When [F2] is pressed, ???Please Input DEST NAME =??? will be displayed.

2.Input the destination number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : LEFT (To scroll to the next 64 sources on the left)

[F4] : RIGHT (To scroll to the next 64 sources on the right)

N : SET DESCRIPTION NAME GROUP

Purpose

To register the Description names required for each remote control unit, set the group of Description names. Up to eight such source and destination groups can be set.

(Up to 160 names can be registered for one group.)

The top half of the screen is for setting the group and the bottom half displays the list of Description names.

Setting Procedure

1.Select menu item [N].

2.Move the cursor to the group number by pressing [B].

3.Enter the group number using the numerical keys, and press [Enter] to set it.

4.Press [F1] to move the cursor to the lower side of screen.

5.Select a number and press [Enter]. The Description name will be copied to the space of the lowest number on the group setting screen.

To erase the Description names on the group setting screen, move the cursor to the number and press [BS],

[DEL] or [Ctrl] _[P].

==================================================================???

???

Example of Setting Screen

m

1.In the remote control unit, the transferred data are all displayed as input/output numbers.

This is because data is transferred using input/output numbers instead of input/output names.

2.The group data of the primary and secondary stations??? must be always the same.

If the primary station data is changed after transfer, be sure to transfer the new data to the secondary station.

5-14

Operating Function Keys

[F1] : MOVE

(To move the cursor up and down between the group setting screen and Description name list)

[F2] : JUMP (To move the cursor to the desired element number)

1.When [F2] is pressed, ???Please Input ELE- MENT NUMBER =??? will be displayed.

2.Input the element number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : SOURCE (DEST.)

When [F3] is pressed, the Description name list

will be changed from destination to source. [B] : GROUP

Press [B] to move the cursor to the group number on the group setting screen.

[L]: COPY (To copy all data in the Description name group to other groups)

1.When [L] is pressed, the message ???Please Input Original Group Number =??? will be displayed to ask for the group number to be copied.

2.Input the group number to be copied with the

numerical keys and press [Enter]. The data of all group will be copied to the group setting screen currently displayed.

[S]: SEND (Transfers all data on the group setting screen currently displayed to a secondary station)

1.When [S] is pressed, a message ???Please Input Station Number =??? will be displayed to ask for the number of a secondary station to which the data is to be transferred.

2.Input the number of the secondary station using the numerical keys and press [Enter].

All data on the group setting screen currently displayed will be transferred to the secondary station.

ROUTING SWITCHER SYSTEM (E)

O: SET TIE LINES

Purpose

This menu is used to store the connection information of the matrix in the primary station and to set the tie line for switching several crosspoints using the remote control unit button. Using this method, peripheral units such as the signal converters can be used more efficiently.

The tie line consists of four input/output connectors as one group and paths connected between sources and destina- tions. The tie line system consists of a maximum of 20 groups for sources and destinations respectively, and a maximum of 40 groups for connections, called Net groups.

Setting Procedure

Before you perform the tie line management using two or three routing switchers, you should set the unit location and the elements of the tie line as follows.

1.Set the offset of each unit on the menu screen [A : SET UNIT LOCATION] of the secondary station in order to avoid repeated input/output numbers of multiple units and locate the units on one physical level.

2.Set the elements of the tie line on the menu screen [O :

SET TIE LINE]. Select menu item [O].

The top half of the screen is for setting the source group while the bottom half is for setting the tie line path.

Example of Source Group Setting Screen

3.Select a source group number using the cursor and press [Enter]. The source number input mode will be set.

Set the source name to the desired source group.

4.Input the source number using the numerical keys and press [Enter] to set it. If [Ctrl] _[F] is pressed

before the setting, the original source name will be returned. When [Ctrl] _[P] is pressed, the source

name will be deleted and ??? ?? ?? ?? ?? ??? will be displayed.

5.After setting the source group, press [F5]. The top half of the screen will be switched to the destination group setting screen.

Example of Destination Group Setting Screen

6.Set the destination group in the same way as for the source group.

7.After setting the destination group, press [F5] and set the net group setting screen.

Example of Net Group Setting Screen

8.Select the number of net group with cursor keys and press [Enter] to set the input mode.

Set the signal path between two routing switchers, using the combination of the

???OUT of the front stage??? > ???IN of the latter stage???.

9.Input the source number and the destination number with the numerical keys and press [Enter] to set it.

When change the level, move the cursor to the level and press [Enter].

10.Press [F1] to move the cursor to the tie line path setting screen.

Set tie line paths using the combination of ???Source group??? _???Net group??? _???Net group??? _ ???Destination group???.

The two ???Net groups??? can be set at a maximum. However, leave one ???Net group??? blank when there are two routing switchers to be connected.

11.Move the cursor to a path number and press [Enter]. The source group input mode will be set.

12.Input the source group number and press [Enter]. The cursor will move to the net group. Input the net group and destination group in the same way as for the source group. Up to two net groups can be input for one path.

13.Use the above procedure to assign the source, destina- tion and net numbers to each path number.

Operating Function Keys

[F1] : MOVE

When [F1] is pressed, the cursor will move be- tween upper and lower of the screen.

[F2] : JUMP (To move the cursor to the group number of the desired source)

1.When [F2] is pressed, ???Please Input GROUP NUMBER =??? will be displayed.

2.Input the group number of the source to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired number.

[F3] : Pg Up

When [F3] is pressed, the top half of the screen will display the 6 lines previous to the 6 lines displayed

currently. [F4] : Pg Dn

When [F4] is pressed, the top half of the screen will display the 6 lines next to the 6 lines displayed

currently. [F5] : GROUP

(To move the cursor to the top half of the screen and press [F5]. The display will change: ???Source

Gp??? ??? ???Destination Gp??? ??? ???Net Gp???.) [F5] : DISP

(To move the cursor to the bottom half of the screen and press [F5]. The display will change : ???Path??? ??? ???Source Name??? ??? ???Destination Name???.)

5-1. Setting Items of the Primary Station

P : CHANGE PASSWORD

Purpose

This menu is used to change the password.

Setting Procedure

1.Select menu item [P].

2.Input the password currently set, and press [Enter]. In the default status, password is not set in DVS- V3232B/V6464B.

Once the password is set, the menu items can not be set or changed unless the password is entered.

If a wrong password is input, the demand for password input will be displayed again.

3.Enter a new password, and press [Enter]. The new password is verified again.

4.After the new password has been confirmed twice, the screen will return to the menu screen.

5.If not confirmed, the password is demanded again.

Please Input New Password = ________________*???

???

Ctrl-E:RETURN TO MENU

Example of Setting Screen

n

If you forget the password, settings cannot be performed unless the unit is returned to default.

As all table data will be erased when returned to default, be sure you should not forget the password.

Q: CHANGE CROSSPOINT

Purpose

This menu is used to display the crosspoints and change them.

Setting Procedure

1.Select menu item [Q].

2.Select the item using the cursor. Change only the source name.

3.When [Enter] is pressed, the source name input mode will be set. When either key is pressed before entering the source name, the mode will be canceled and the previous display will be returned.

4.Select the code assigned to each type name, and enter the source name using the numerical keys.

5.When [Enter] is pressed, the crosspoint will be set. If [Ctrl] _[F] is pressed before the setting, the original

setting will be returned.

When [Ctrl] _[E] is pressed, the menu screen will be displayed.

m

1.When the power of the primary station is

turned on, ??? ?? ?? ?? ?? ??? will be displayed for a while at the source name position. But once the status of the cross- points is detected, the source name set before hand will

be displayed.

2.Outputs whose destination names are not assigned will be displayed with ??? ?? ?? ?? ?? ???, and crosspoint switching cannot be performed for these.

3.Moreover, names set with the protect function cannot be switched either.

4.When entering the Description name, enter 7 charac- ters from the head.

Example of Setting Screen

Operating Function Keys

[F1] : SEARCH (To select a destination name)

1.When [F1] is pressed, ???Please Input DEST NAME =??? will be displayed.

2.Input the destination name to be retrieved. In the Description name mode, input the Description name (within seven characters) from the head.

3.When [Enter] is pressed, the destination name entered will be searched.

4.If the desired name does not exist in the screen, press [F1] again.

n

If there are several names whose typed characters are the

same in the Description name mode, move the cursor to the first name displayed and press [Enter] to continue moving

the cursor to the next name.

[F1] : SEARCH (To select a source name)

In the Description name mode, the setting proce- dure is as follows.

1.When [Enter] is pressed, the source input mode will be set.

2.Input the desired Description name (within seven characters) from the head.

3.Every time [F1] is pressed, the desired name will be searched.

4.When the desired name is displayed, press Return or Enter to set the crosspoint.

[F2] : JUMP (To move the cursor to the desired destina- tion number)

1.When [F2] is pressed, ???Please Input DEST NUMBER =??? will be displayed.

2.Input the destination number to be retrieved.

3.When [Enter] is pressed, the cursor will move to the desired destination number.

[F3] : Pg Up

When [F3] is pressed, the screen will display the 16

lines previous to the 16 lines displayed currently. [F4] : Pg Dn

When [F4] is pressed, the screen will display the 16

lines next to the 16 lines displayed currently. [F5] : LEVEL

When [F5] is pressed, a level can be selected.

Select the level number using the numerical key and press [Enter]. If [A] is pressed instead of the numerical key and press [Enter] here, the screen

will display a list of all levels. The function keys [F1], [F2], and [F5] on the ALL screen have the

same functions as those of the initial screen menu item [Q].

Example of Setting Screen

5-1. Setting Items of the Primary Station

R : CALL SECONDARY STATION

Purpose

This menu is used to call the menu of the secondary station connected to the S-BUS of the primary station.

Operating Procedure

1.Select the menu item [R] at the menu screen. A message will be displayed on the screen.

2.Enter the station number of the secondary station, and press [Enter]. The display will be changed to the

menu screen of the secondary station.

3.If [Ctrl] _[D] is pressed, the screen will return to the menu screen of the primary station.

m

1.If the specified secondary station does not exist on the S-BUS data link, the following message will be displayed.

Display: ???Station dose not exist???

2.If the specified secondary station is not

available for communication, the following message will be displayed.

Check at the menu item [F : SET ACTIVE UNIT NUMBER].

Display: ???Disable Station???

CALL STATION NUMBER ? ???

???

Ctrl-E:RETURN TO MENU

Setting Screen

S : SELECT INDICATION COLOR

(Except for BKPF-R70 and HDS-V3232)

Purpose

If this menu is set to ???ON???, the screen will show a color display during the use of the Sony control terminal BAC- 1200.

Setting Procedure

1.Select menu item [S].

2.When [S], [Enter] is pressed, the setting condition displayed will be switched (???ON??? ??? ???OFF??? ??? ???ON???

...).

n

As wrong characters will be displayed before and after the menu items when a control terminal except Sony control terminal BAC-1200 is used, be sure to set to ???OFF???.

T : SET CLOCK

Purpose

This menu is used for the setting of the time. The time set at this menu will be used for recording the time of error occurrence.

Setting Procedure

1.Select menu item [T].

2.Enter the time using the numerical keys, and press [Enter] to set it.

The screen will be changed to the menu screen automatically.

n

If [Ctrl] _[E] is pressed without pressing [Enter], the screen will return to the menu screen and the setting modification becomes invalid.

1993.02.03-22:24(Y.M.D-H:M) READ TIME??? CHANGE TO = 1993.02.03-22:24???

???

Ctrl-E:RETURN TO MENU??

Example of Setting Screen

U : SELECT REMOTE

Purpose

This menu is used to control the routing switcher using the 9-pin remote (REMOTE 2), and to set the control mode to the DIRECT mode or the S-BUS conversion mode.

Setting Procedure

1.Select menu item [U].

2.Select channel using the cursor keys.

3.Press [Enter], and the setting condition displayed will

be changed.

DIRECT ??? CONVERT RS422 (CART +) to S-BUS

Example of Setting Screen

DIRECT:

In this mode commands received using RS-422A are not converted to those for the S-BUS (REMOTE 1) and are directly used for controlling the receiving station. If this mode is selected, a protocol must be selected at the secondary station.

CONVERT RS-422 (CART +) to S-BUS

This mode converts commands received using the RS- 422A to those for the S-BUS.

n

How to use UA2 Code:

The original use of the UA2 code in the RS-422A protocol is to identify the multiple equipments which are connected by loop-through connection, and be controlled.

Each equipment is controlled by the control command with UA2 code which corresponds to the unit address of each equipment.

The UA2 code is converted to the level control command when the RS-422A commands are converted to the S-BUS levels.

The following examples show how UA2 codes are con- verted to the S-BUS level.

UA2 = 01 ??? 00000001 ??? S-BUS level 1 UA2 = 02 ??? 00000010 ??? S-BUS level 2 UA2 = 04 ??? 00000100 ??? S-BUS level 3 UA2 = 08 ??? 00001000 ??? S-BUS level 4 UA2 = 10 ??? 00010000 ??? S-BUS level 5 UA2 = 20 ??? 00100000 ??? S-BUS level 6 UA2 = 40 ??? 01000000 ??? S-BUS level 7 UA2 = 80 ??? 10000000 ??? S-BUS level 8 UA2 = FF ??? 11111111 ??? S-BUS All level

The following combinations of levels are also possible.

UA2 = 03 ??? 00000011 ??? S-BUS level 1 and 2 UA2 = 07 ??? 00000111 ??? S-BUS level 1, 2 and 3

n

The S-BUS conversion mode can be used only when the primary station is controlled by the 9-pin remote control. Therefore, use the DIRECT mode whenever a secondary station is controlled by the 9-pin remote control.

W:SYSTEM STATUS LOG

Purpose

This menu is used to check the error during self-diagnosis of each station, the status of the S-BUS circuit, and the time of events.

1990.10.12-15:42 S-BUS LINK DISCONNECTED???

1990.10.27-09:28 STARTED BY BKS-R1601 Ver3.10 IN STATION 11??? 1990.11.03-05:31 STARTED BY BKS-R3204 Ver3.11 IN STATION 32??? 1991.01.14-13:51 MISSING REFERENCE SIGNAL IN STATION 1??? 1991.02.01-11:15 POWER SUPPLY UNIT B DOWN IN STATION 4??? 1991.02.04-06:11 X-POINT ERROR IN STATION 1???

-- end --???

Ctrl-E:RETURN TO MENU

Example of Display

Operation Procedure

1.Select menu item [W].

2.When all status cannot be displayed on the screen,

??? __more __??? will be displayed at the bottom of the screen. Press [SPACE] key to display the next

status. When all status have been displayed, ??? __end

__??? will be displayed.

3.Press [Ctrl] _[E] to return to the menu screen.

System Status Screen

Refer to ???6. Confirmation of Function??? for detail of the system status screen.

n

.To erase the LOG contents in DVS-V3232B/V6464B, set the S3 switch on the CPU-149 board to ???C??? (Clear) and then press the S5 switch (Reset).

After erasing, be sure to return the S3 switch to ???0??? and press the S5 switch (Reset) again.

.To erase the LOG contents in HDS-V3232, set the S2 switch on the CPU-251 board to ???C??? (Clear) and then press the S8 switch (Reset).

After erasing, be sure to return the S2 switch to ???0??? and press the S8 switch (Reset) again.

5-1. Setting Items of the Primary Station

X : DISPLAY S-BUS COMMUNICATION

Purpose

This menu is used to display the S-BUS data received at the primary station.

Setting Procedure

1.Select menu item [X].

2.To stop the scroll, press [Ctrl] _[E]. (???TRACE OFF??? will be displayed at the bottom of the screen.)

3.The menu screen will be returned when [Ctrl] _[E] is pressed again.

Ctrl-E:RETURN TO MENU

Example of Display

n

For details on the contents of the display, refer to the S- BUS Protocol Manual.

5-1. Setting Items of the Primary Station

Y : DISPLAY TABLE (Except for HDS-V3232)

Purpose

This menu is used to display the table data set with the control terminal.

Operation Procedure

1.Select menu item [Y]. The following message will be displayed at the bottom of the screen.

Display : ???DISPLAY TABLE DATA? (y/a/n)???

2.Press [E], and the signal format (4: 2: 2/4 fsc) set for each input/output will be displayed in hexadecimal.

(DVS-V****series only.)

Press [A], and all table data will be displayed in

hexadecimal.

When [N] is pressed, the table data display will be canceled.

3.If [SPACE] is pressed during the display, the display will be interrupted. When [SPACE] is pressed once

again, the display will begin.

4.Press [Ctrl] _[E] to stop the display. The menu screen will be displayed.

Example of Display

n

For the contents of the table data, refer to the S-BUS Protocol Manual.

Z : SET UNIT DETECTABLE

Purpose

This menu is used to check the possibility of communica- tion of secondary stations connected to the S-BUS data link periodically.

During checking, ??????? appears. After the completion of checking, the code number indicating the type of each device appears.

If the secondary station does not communicate for a given period, the message below appears.

???STATION ***FAILURE (DISCONNECT OR POWER DOWN)???

Station number

Setting Procedure

1.Select the menu item [Z].

2.Select a secondary station you want to check using the cursor.

3.Press [Enter], and ??????? appears.

To cancel ???????, press [Enter] again.

4.Press [Ctrl] _[E], and the display is changed to the menu screen to begin checking.

5.After about ten seconds, select the menu item [Z]. If the secondary station is available for communication, ??????? changes to a device code number.

n

A secondary station to be checked should be set available for communication in advance at menu item [F : SET

ACTIVE UNIT NUMBER]

Example of Setting Screen

A:SET UNIT LOCATION

Purpose

This menu is used to set the input/output location of the routing switcher.

Setting Procedure

1.Select menu item [A].

2.Use the cursor keys ([&], [*] to select the setting item.

3.When [Enter] is pressed, the offset value of the input number and the output number can be typed.

4.Enter the offset value using the numerical keys.

5.Press [Enter] to set the offset value.

If [Ctrl] _[F] is pressed before the setting, the original offset value will be returned.

The location is assigned consecutive numbers from the offset value. The following table lists the input and output control area assigned from the head number consecutively.

m

1.In the initial status (factory setting), the head number is set to ???1???.

2.When DVS-V3232B/V6464B, BKPF-R70 or HDS- V3232 is used as the primary station, input/output number can be set freely using the menu item [L : SET

PHYSICAL ASSIGNMENT].

The setting values in this menu are physical input/ output/level numbers.

When selecting crosspoints from the remote control unit, the virtual input/output/level numbers set at the menu item [L] are used. In the initial status of [L], the physical numbers equal the virtual numbers.

512

(Output)

H : SET PHANTOM TABLE

Purpose

This menu is used to set PHANTOM which switchers several crosspoints, using the source selection button of the remote control unit.

Setting Procedure

1.Call the menu screen of the remote control unit to be set, using menu item [R], and then select menu item [H].

2.Select a item using the cursor.

3.When [Enter] is pressed, the phantom table can be set. If [Enter] is pressed before setting, the registration

will be deleted.

4.Input the data to the phantom table. The phantom function consists of the global phantom function registered at the primary station, the normal type of local phantom function registered at each remote control unit and the destination off set type of local phantom function.

. Setting the Global Phantom Function

Input the phantom name with the type name and the number. Next, press [G] at destination name position. Lastly, input the global phantom number (four digits) set at the primary station.

.Setting the Normal Type of Local Phantom Function

a)At [J : NAME STYLE (Type +Num)] in the primary station menu item [J], input the type name (between 0 and F) and the number for the phantom name, destination name, source name and level number respectively. (When the remote control unit button is pressed, crosspoints with the same phan- tom name will be switched together.)

b)At [J : NAME STYLE (DESCRIP. NAME)] in the primary station menu item [J], input the phantom name and level number in the same way as a). For the source name and destination name, the Descrip-

tion name and ???Type +Number??? name can be

selected freely.

Each time [Ctrl] _[N] are pressed, the Description name input mode and ???Type +Number??? name input mode will be switched alternately.

Description name input mode :

Use the alphabet and numerical keys to enter seven characters from the head of the Description name.

???Type +Number??? name input mode : Input in the same way as a).

ROUTING SWITCHER SYSTEM (E)

n

If a Description name has been set for the input/output number, the display of Description has priority to the display of ???Type +Number??? even if the ???Type +Number??? name is set.

Example of Setting Screen (Normal Type)

.Setting the Local Phantom of the Destination Offset Type

Enter the phantom name, source name and level number in the same way as the ordinary local phantom.

When [+] is depressed while the cursor is positioned in the DESTINATION column, the system enters the Replace- ment Variable ???DST +n??? input mode. Enter the offset value ???n??? in this status.

Example of Setting Screen (Destination Offset Type)

5-27

5.When [Enter] is pressed, the phantom table will be set.

6.When [Ctrl] _[E] is pressed, the menu screen of the secondary station will be displayed. When [Ctrl] _ [D] is pressed, the menu screen of the primary station

will be displayed.

. Execution of Phantom Function

When the phantom function is performed by a remote control unit, its operation conforms to this phantom table. It is possible to switch with the specified level or to set ON

(1) or OFF (0) for each level. When level ???0??? is set or when ???0??? is set for all levels, the level value will that set for the destination name specified in the phantom table. The indication (specified on the menu item [E : SET LEVEL TABLE] of the primary station) is as follows : [Phantom name : Output terminal name < input terminal name ??? level setting].

Internal Process After TAKE Button Pressing :

When pressing the TAKE button after selecting a source/ phantom the following internal process is made. In BKS- R1607/R1608/R3209/R3210, TAKE is processed immedi- ately by pressing the source selection button.

TAKE button is pressed

Checks if the selected name exists on the phantom table

Output the global Select the source/destination phantom number set in the phantom table

Check if the secret or protect is set to the selected source and destination

Omit the source and destination to which the secret or protect is set

Check the level setting of the remaining source and destination for each name.

If the setting is 0, the level is transferred from the destination table

K : RESET TO DEFAULT TABLE

K : DEFAULT TABLE

Purpose

This menu is used to initialize the table data. Do not perform this menu when modifying the table data.

Setting Procedure

1.Select menu item [K]. The message ???RESET TO DEFAULT TABLE ok ? (y/n)??? will be displayed at the bottom of the screen.

2.Press [Y] to process the initialization. To cancel initializing, press [N].

n

The table data will be lost note when performing the menu item [K].

5-2. Setting Items of the Secondary Station

L : COPY TABLE DATA

Purpose

This menu is used to copy the table data of the specified remote control unit. This applies to the remote control unit as follow.

. Version 3.00 or later : BKS-R1601/R3202/R3203 /R3204/R3205/R3206

. Version 1.00 or later : BKS-R1607/R1608/R3209/R3210

Setting Procedure

1.Select menu item [L]. This item can be selected from both the menu and another setting screen.

2.As the message ???Station Number???? will be displayed on the screen, input the station number of the unit to be copied. Select the table name to be copied, from A, P, B and D, using the alphabet keys.

3.When [Enter] is pressed, the table data will be copied, and the screen will return to the setting screen.

4.When [Ctrl] _[E] is pressed again, the screen will

return to the menu screen of the secondary station. When [Ctrl] _[D] is pressed, the screen will return to

the menu screen of the primary station.

SONY ROUTING SYSTEM SETUP MENU BKS-R3202 V3.10 STATION NUMBER 6???

???

???

???

???

A:Copy All table??? P:Copy PHANTOM table??? B:Copy PANEL table???

D:Copy Available Destination table??? Inputs A,P,B,D,0-9 Selected = A???

Station Number ????

???

Ctrl-E:MENU Ctrl-D:RETURN

ROUTING SWITCHER SYSTEM (E)

Example of Setting Screen

Selected = A All the table data are copied.

Selected = P Data set at the menu item [H : SET PHAN- TOM TABLE] are copied.

Selected = B Data set at the menu item [N : SET PANEL TABLE] are copied.

Selected = D Data set at the menu item [O : SET AVAIL- ABLE DESTINATION] are copied.

n

The copy function of BKS-R****guarantees upper compatibility only.

The remote control unit except for BKS-R1607/R1608/ R3209/R3210 may lost a part of the data, when coping the data from Ver. 3.**unit to Ver. 1.**unit, a part of the data may be lost (global phantom, etc.).

The function is effective when copying the data from Ver. 1.**unit to Ver. 3.**unit in a system.

5-29

5-2. Setting Items of the Secondary Station

M:SET MONITOR FUNCTION (Except for HDS-V3232)

Purpose

This menu is used to set the monitor S-BUS. As this monitor function is controlled by the local CPU, it has a monitor data link that is independent from the standard S- BUS data link.

Therefore, it is necessary to set the primary station and secondary stations for the monitor S-BUS.

Setting Procedure

(For the Primary Station on the Monitor S-BUS)

1.Select menu item [M].

2.The menu screen of the primary station on the monitor S-BUS will be displayed.

For details of setting this menu, refer to ???5-3. Setting Items of the Primary Station on Monitor S-BUS???.

Example of Setting Screen

N : SET PANEL TABLE (BKS-R1601/R3202/R3203)

Purpose

This menu is used to assign source name to each source selection button.

Setting Procedure

1.Select menu item [N].

2.Select a button number using the cursor.

3.When [Enter] is pressed, the source name can be typed. If [Enter] is pressed before inputting the

source name, the registration will be deleted.

4.Select the code assigned to each type name, and use the numerical keys to enter the source name.

5.Press [Enter] to set the source name.

6.Press [Ctrl] _[E] to return to the menu screen of the

secondary station.

Press [Ctrl] _[D] to return to the menu screen of the primary station.

Example of Setting Screen

Purpose

This menu is used to assign source/destination name to each source/destination button.

Setting Procedure

1.Select menu item [N].

2.Select a button number using the cursor.

3.When [Enter] is pressed, the panel table can be typed. To delete the registration, press [Enter] before

inputting the name.

4.a) When [J : NAME STYLE (Type +Num)] is selected in the primary station menu, input the type name (between 0 and F) and the number for the source and destination name.

b)Each time Ctrl N is pressed when [J : NAME STYLE (DESCRIP. NAME)] is selected in the primary station menu, the following input mode will be switched alternately.

Description name input mode :

When ???Ctrl _N : Type +Num??? is displayed on the

screen, it means that the name mode will be changed to ???Type +Number??? by pressing [Ctrl] _

[N].

Input Description name from the first to seventh characters using the alphabet and numerical keys.

???Type +Number??? name input mode: Input in the same way as a).

n

If the Description name has been set for the input/output number, the display of Description has priority to the display of ???Type +Number??? even if the ???Type +Number??? name is set.

5.When [Enter] is pressed, the source name is set.

6.When [Ctrl] _[E] is pressed, the menu screen of the

secondary station will be displayed.

When [Ctrl] _[D] is pressed, the menu screen of the primary station will be displayed.

Example of Setting Screen

m

1.In the BKS-R1617/R1621, each button (key) can be set to both source and destination. In case source and destination are set to the same button (key), the DEST button works as a destination button when the DEST button lights in amber and the DEST button works as a source button when the DEST button lights in green. In the 4 DESTINATION mode, both source and destination can be set to only buttons (keys) 01 to 04. Other than setting of source button (key), the destina- tions of block 1 to 4 can be set to destination buttons 01 to 04.

Be sure to set either source or destination on the respective buttons (keys) when setting other model. If both source and destination are set to the same button (key), it will cause malfunction.

2.Set the table data of BKS-R3204/R3205/R3206 by eight buttons previously in the menu item [Z : SET

____PANEL STATUS]. If ???KEY = ____??? is displayed on the key number position, the name can not be input.

3.When setting description names to the source/destina- tion buttons, select a name from the description name group sent to the remote control unit.

If other names are input, these will not be set even if the [Enter] button is pressed.

In such cases, transfer the group including the desired description name from the primary station.

5-2. Setting Items of the Secondary Station

4.When ???T : TAKE M : MONI??? is displayed on the screen, it means that the button on the source side can

be set as the TAKE button or MONI button.

Before pressing [Enter], select a key from the source side. To set it as the TAKE button, press [T]; to set it as the MONITOR button, press [M].

5.When ???V : VTR??? is displayed on the screen, it means that the VTR control function can be assigned to the

buttons on the source side.

Before pressing [Enter], select a key from the source side and press [V].

Enter the number according to the list of operations on the bottom of the screen.

6.When ???E : LEVEL??? is displayed on the screen, it means that the level control function can be assigned

to the buttons on the source side.

Before pressing [Enter], select a key from the source side and press [E].

Enter the number according to the list of levels on the bottom of the screen.

n

In BKS-R1607 of version V1.10 and higher, any desired button among the sixteen buttons can be set as a TAKE button.

When this setting is performed, the name selected by the SELECTOR knob on the front panel can be taken by pressing the TAKE button.

(Maximum inputs 512 xoutputs 512)

The actual setting procedure is as follows. Select a key from the source side which you want to use as the TAKE button. Press the [T] button.

Example of Setting Screen

N : SET PANEL TABLE (BKS-R3206/R3216)

Purpose

This menu is used to assign source name and destination name to be displayed.

Setting Procedure

The setting procedure is the same as that of menu item [N : SET PANEL TABLE] (BKS-R3204).

m

1.The setting of [SET PANEL TABLE (SOURCE)] assigns the source name and [SELECT DESTINA- TION] assigns the destination name.

2.The destination name can also be assigned using the button on the front panel. Refer to the Operation Manual for setting.

3.If ???Type +number??? name mode is selected in the menu item [Z : SET PANEL STATUS], (refer to the Operation Manual of BKS-R3206) ???SET PANEL TABLE (SOURCE)??? is not displayed.

Example of Setting Screen

Example of Setting Screen

ROUTING SWITCHER SYSTEM (E)

4.Press [Ctrl] _[F] to switch to the display allowing setting of the selectable sources.

Pressing [Ctrl] _[E] switches to the menu screen of

the secondary station.

Pressing [Ctrl] _[D] returns to the menu screen of the primary station.

5-33

.Procedure of setting SELECT SOURCE NAME

1.Select an item to set using the cursor key.

2.Pressing [Enter] establishes the source name input mode.

3.Enter the ???Type +No.??? name or description name.

4.Press [Enter] to confirm the input contents.

Example of setting

When the ranges of input and output selections are limited as shown in the above table, the setting display and the virtual matrix are configured as shown below.

Example of Setting Screen

(Setting the range of selectable sources)

n

In BKS-R1607/R3210 of version V1.10 and higher, the sig- nal switching cannot be performed when the destination range that is set by SELECT SOURCE NAME is exceeded even when the destination-type offset phantom has already been set using the menu item [H]. Setting must be per- formed so that the resultant value of destination after addi- tion and subtraction of offset stays within the eight blocks of SELECT SOURCE NAME. When the offset value is zero (DST+0), the signal switching can be operated.

5-34

64

101

Block 3

m

1.When selecting the destinations that have no limit of range, the selectable range of sources is from 001 to 1024.

2.BKS-R3216/R1617/R1618/R3219/R3220/R1621 makes all the sources within the range that includes the selected destinations valid. OUT001 makes the multiple ranges of IN001 to IN064 and IN101 to IN164 valid when the selection is made as shown in ???Example of Setting Screen???.

In BKS-R1607/R3210 of version V1.10 and higher, a pair of source signal and key signal can be output as an inter- locked pair using the offset-type phantom. (See OUT1 to OUT4 in the following illustration.)

Odd number : Source

Even number : Key

1

2

3

4

5

6

7

8

9

(Output)

ROUTING SWITCHER SYSTEM (E)

Purpose

This is the function to display the source names that are expanded by combining the two switchers for the purpose of expanding numbers of input.

When a route is set, the source that is connected to the route destination, is automatically chased out the and the name of the source is displayed. In an example shown below, IN001 of the switcher A is displayed as the source name when OUT017 of the switcher B is selected.

It has another function as follows. When a request of switching including the expanded destination, is issued, crosspoint of the route destination side is automatically switched. For example, when IN001-OUT001 of the switcher A is switched, IN005-OUT017 of the switcher B is also switched at the same time.

Route Function

Ctrl-E:MENU Ctrl-D:RETURN Ctrl-N:DESCRIP.NAME +:DST+???

???

Example of Setting Screen

In the setting screen example as shown above, the cross- point of IN005-OUT017 is switched at the same time when a crosspoints including OUT001 (ex. IN002-OUT001) is switched. Then, source (IN002) of the switcher-A???s OUT001 is displayed (IN002-OUT017) for OUT017 of the switcher-B. The above described operation is executed by selecting OUT001 and IN002 from the remote control unit. However, it is recommended to set the phantom of IN002: OUT001 < IN002 beforehand on the remote control panel, because the operation of selecting IN002-OUT001 instead of OUT017 looks unnatural when IN002-OUT017 is going to be taken.

Setting procedure

1.Select the menu item [R] of the secondary station.

2.Select the desired item using the cursor key.

3.Pressing [Enter] establishes the route setting mode. When [Enter] is pressed again before entering data,

registration is canceled.

4.Enter the ???Type +No.??? name or description name. (The setting methods remains the same as that of phantom. Refer to the description of the secondary station???s menu item [H : SET PHANTOM TABLE]. However, the destination name of the switcher-A to which source of the switcher-B is connected, should be input on this menu, instead of the phantom name.)

5.Press [Enter] to confirm the input contents.

6.Pressing [Ctrl] _[E] switches to the menu screen of

the secondary station.

Pressing [Ctrl] _[D] returns to the menu screen of the primary station.

5-36

To add the offset amount to the selected destination, enter [+] in the DEST column before pressing [Enter].

After ???DEST +??? is displayed, enter the offset value (0 to 1023) and press [Enter] to store the value.

Each level can be set by selecting ON (1) or OFF (0).

ROUTING SWITCHER SYSTEM (E)

S : DISPLAY DESCRIPTION NAME

Purpose

This menu is used to check the group and names of the Description transferred from the primary station.

Check Procedure

1.When [Enter] or [SPACE] is pressed, the screen will be changed to the next page.

2.When [BS] or [DEL] is pressed, the screen will be changed to the previous page.

3.Press [Ctrl] _[E] to display the menu screen of the

secondary station.

Press [Ctrl] _[D] to display the menu screen of the primary station.

Example of Setting Screen

n

In BKS-R1607/R1608/R3209/R3210 of version V1.10 and higher, the 160 description names that are transferred from the primary station can be registered in the range of inputs 512 xoutputs 512 in the order of terminal number regard- less of the block number. When you want to use more than 160 of the description names, transmit the names from the primary station after dividing the description names into several blocks.

The following operations are possible from the screen. Look at destination from source side : [*] key Look at source from destination side : [&] key

Example of Setting Screen

U : SELECT REMOTE PROTOCOL

Purpose

This menu is used to set channels A and B of REMOTE 2 (D-sub 9-pin) to loop-through. When the REMOTE 2 control mode is set to DIRECT, this menu is used to set the protocol and the conversion table of the input/output numbers.

There are three kinds of protocols.

. PRODUCTION SWITCHER PROTOCOL

. AUDIO MIXER PROTOCOL

. CART PROTOCOL

n

AUDIO MIXER PROTOCOL was known as ???SWITCH- ER PROTOCOL??? before.

Set the conversion table of the input/output numbers so that the input/output numbers defined by the external controller will correspond to those of the routing switcher. In the THROUGH mode, there will be no setting menu for channel B. For details of the DIRECT mode, refer to the menu item [U : SELECT CONTROL MODE] in the primary station.

Setting Procedure

n

The same number cannot be set to more than one place. If the same number is used, the message ??? *** is used already; Ignored??? will be displayed and the cursor will stop at its current position.

1.Select menu item [U].

2.???SELECT RS-422 CHANNEL =? (A B) A??? will be

displayed. Input A or B using the alphabet keys and press [Enter]. The screen will change to the setting

screen of the selected channel.

3.The cursor will be placed at ???1=001??? of ???SET DESTI-

NATION TRANSCODE???.

When [Enter] is pressed, ???1=??? will be displayed and the number can be typed. The left ???1??? in ???1=001??? indicates the input/output number of the switcher and the right ???001??? indicates the command number received.

4.Input a number between 1 and 128 and press [Enter] set it. The cursor will move to the next number.

If ???00??? is input, ???001??? will be displayed. If number

129 or later is input, the previous number will be displayed. If [Enter] is pressed without inputting

anything, invalid crosspoints will be set so that the

screen will show ??? ?? ?? ?? ?? ???, and the cursor will move to the next number. When [Ctrl] _[F] is pressed before

the setting, the previous number will be displayed and the cursor will move to the next number.

Example of Setting Screen

Operating Function Keys

[F1] : REMOTE (To switch the protocol)

1.When [F1] is pressed, the cursor will move to ???REMOTE???.

2.When [Enter] is pressed, the protocol will be switched. To change the ??? ***??? of ???UA2 =???,

select the desired position with the cursor and press [Enter] to switch 1/0 alternately.

n

The description ??? ***??? of ???UA2 = ***??? on the above menu corresponds to the DIP switch setting which LSB is at the left end.

[F2] : DEFAULT (Initializing the data)

1.When [F2] is pressed, ???DEFAULT ok? (y/n)??? will be displayed at the bottom of the screen.

2.When [Y] is pressed, the program will be executed. When [N] is pressed, it will not be

executed.

[F3] : DEST

When [F3] is pressed, the cursor will move to the

destination side. [F4] : SOURCE

When [F4] is pressed, the cursor will move to the

5-38

source side.

ROUTING SWITCHER SYSTEM (E)

V : DISPLAY UNIT STATUS (Except for HDS-V3232)

Purpose

This menu is used to display the status of the hardware such as boards, etc.

n

For the input/output boards and matrix boards of DVS- V3232B, channel 1 to 32 will be displayed. And FAN 1 and 2 will be displayed for DVS-V3232B.

Operating Procedure

1.Select menu item [V].

2.Press [Ctrl] _[E]. The menu screen will be dis- played.

BINVALID ???

???

???

??? ??? ???Ctrl???-E:RETURN TO MENU

Example of Display

Y : DISPLAY TABLE DATA (Except for HDS-V3232)

Purpose

This menu is used to display the table data set with the control terminal.

Operation Procedure

1.Select menu item [Y]. The following message will be displayed at the bottom of the screen.

Display: ???DISPLAY TABLE DATA? (y/n)???

2.Press [Y], and the 4:2:2/4 fsc setting value will be displayed in hexadecimal. Press [A], and the table

data will be displayed in hexadecimal.

When [N] is pressed, the table data display will be cancelled.

3.When [SPACE] is pressed during the display, the display will be interrupted. When [SPACE] is

pressed once again, the display will begin.

4.Press [Ctrl] _[E] to stop the display. The menu screen of the secondary station will be displayed.

Example of Display

Purpose

This menu is used to set the display mode.

The setting contents are as follows.

DISPLAY MODES (BKS-R3216/R3220): Selects the display type. (when J : NAME STYLE

(DESCRIP.NAME) is selected in the primary station menu.)

NORMAL = Normal display

2 +2CHAR = Displays two letters before and after the name.

4CHAR = Displays four letters from the beginning of the name.

n

If 2 : 2 +2CHAR or 3 : 4CHAR is selected when J : NAME STYLE (Type +Num) is selected in the primary station menu, the two letters and two numbers of the type name are displayed.

PANEL FUNCTION (BKS-R1617/R1618/R3219/R1621): Sets the operation mode of the panel.

NORMAL = Normal selection mode

4 DESTINATION = Destinations can be set for each block of the source button that consists of four blocks.

Set each source button and also set the destination of each block using the menu item [N : SET PANEL TABLE].

TALLY GROUP

Selects the tally group.

Setting Procedure

1.Select the menu item [Y].

2.The cursor appears in ???DISPLAY MODES = 1???.

Move the cursor to an arbitrary mode and press [Enter] establishes the input mode.

3.Enter the desired number with the numeric keys. Press [Enter] to set the number ; the cursor moves to

the next setting item.

If you do not want to change the default value, press [Enter] without entering any number.

4.To set ???TALLY GROUP???, move the cursor to the

position of the desired tally (in the case of tally 2, second ??? _??? from the left) and press [Enter]. The item is toggled on and off every time [Enter] is pressed.

(When the number is displayed, the item is ON. When ??? _??? is displayed, the item is OFF.)

Ctrl-E:MENU Ctrl-D:RETURN???

???

Example of Setting Screen

Z : SELECT SDI FORMAT (Except for HDS-V3232)

Purpose

This menu is used to set the format of signals fed to the input/output board of DVS-V3232B and DVS-V6464B with the control terminal.

This setting is available when the manual switch for the format on each input/output board is OFF.

Setting Procedure

1.Select menu item [Z].

2.Select a channel line using the cursor to be set. (The channels will be switched by eight channels. Displayed signal formats that are enclosed by the round brackets as ???(4:2:2)??? have been set on the board and cannot be modified with the control terminal.

3.When [Enter] is pressed, the setting will change (???4:2:2??? ??? ???4 fsc NTSC??? ??? ???4 fsc PAL???).

4.Press [S] (Table Set), and the content now appeared is copied to the area of SDI FORMAT TABLE.

5.Press [Ctrl] _[E] to stop the display and the menu screen of the secondary station will be displayed.

F1:FORMAT F2:FIELD S:Table Set Ctrl-E:RETURN TO MENU

Example of Setting Screen

n

Unless pressing [S], the data will be deleted when the power is turned off.

Operating Function Keys

[F1] : FORMAT (Mode which sets the signal format by 8- channels)

[F2] : FIELD (Mode which sets the crosspoint switching field)

1.Press [F2]. The cursor will move to ???SWITCH ING FIELD??? in the menu.

2.Press [Enter]. The setting will change. (ODD ??? EVEN ??? FIELD ??? ASYNC ??? ODD)

All switching field in the switcher are deter mined by this setting.

n

To use RS-422A and S-BUS together, set the switching field as follows.

1 When using the S-BUS and CART protocol together :

ODD

2When using the S-BUS and PRODUCTION SWITCHER protocol together : FIELD

Note that the switching timing of the CART will not be accurate if the CART and PRODUCTION SWITCHERS protocols are used together.

Switching timing is not guaranteed in the combination of different switching fields.

For details of the signal switching timing, refer to ???5-8. Signal Switching Timing???.

Z : SET PANEL STATUS (BKS-R3204/R3205/R3206)

Purpose

Besides the remote control unit can be used alone, several units can be used together as if it were one unit with expanded sources and destinations. When using several units together, one will serve as the mother and the rest will serve as the daughters.

This menu is used to perform the settings necessary in such cases. The selection of stand alone use, mother use, and daughter use is performed in this menu in addition to the assignment of buttons on the front panel. If assigned as the mother station, a block number should be set. (up to 10 mothers can be registered.)

Setting Procedure

1.Select menu item [Z].

2.Place the cursor on ???PANEL MODE=1??? and press [Enter] to select an item. Selection should be per-

If selection is not necessary, press [Enter] again.

3.Place the cursor on ???KEY 1-8=S??? and press [Enter] to set S or D. The button number is set in order from top left to right, then left bottom to right as shown below.

To change to the next setting, press [Enter].

4.When ???PANEL MODE=2??? (the MOTHER) is select-

ed, move the cursor to ???SET BLOCK NUMBER=X??? and press [Enter] to enter block number. When [Enter] is pressed again, the block number will be set.

If the mother station is set, the ID are displayed.

5.When ???PANEL MODE=3??? (the DAUGHTER) is selected on BKS-R3204, the MOTHER ID number is displayed as ???MOTHER STATION ID= xx???. The MOTHER ID number is set using the switch on the rear panel. If switch setting is 0, 1, 255, ???Incorrect ID (0, 1, 255) is designated.??? is displayed, while ???The designated ID is not found??? is displayed if the mother station ID is not registered in the block.

6.In setting of BKS-R3206 different from BKS-R3204/ R3205, there is no ???SELECT SOURCE OR DESTI- NATION ASSIGNMENT???, Use either ???Type name + Number??? or ???the source direct??? to designate the source

name.

???PANEL LAYOUT= x??? is displayed. Press [Enter] and input the numbers.

7.Press [Ctrl] _[E] to display to the menu screen of the

secondary station.

Press [Ctrl] _[D] to display to the menu screen of the primary station.

n

When ???PANEL MODE=1??? (the STAND ALONE) is selected on BKS-R3204 and BKS-R3205, all KEYs (1 to 32) can not be assigned as DESTINATION. If all is set as DESTINATION, the KEYs 1 to 8 are set to ???KEYs 1 to 8=S??? automatically.

SONY ROUTING SYSTEM SETUP MENU??? BKS-R3204 V3.10 STATION NUMBER 14???

SET PANEL STATUS???

???

Example of Setting Screen (BKS-R3204)

Example of Setting Screen (BKS-R3206)

5-2. Setting Items of the Secondary Station

Z : SET PANEL STATUS (BKS-R1607/R1608/ R3209/R3210/R3216/R1617/R1618/R3219/ R3220/R1621)

Purpose

This is the function to set the various modes of the remote control unit. In the models corresponding this menu as shown above the multiple units can be connected in order to expand the number of sources and destinations which can be controlled simultaneously. Setting the mother panel and the daughter panels is performed from this menu. (Maximum ten mother panels can be set.)

Contents to be set are shown below.

DISPLAY MODE

STATUS = Indicates the status of the primary station???s crosspoint table.

PROMPT = The depressed button lit immediately.

PROTECT MODE

ON AIR = Switching is performed from that panel even after protected.

NORMAL = Switching is prohibited after protected. FLEXIBLE = Switching is prohibited after protected.

However, protections by other stations can be released.*1

FLEX & OA =Uses the functions of both 1 : ON AIR and 3 : FLEXIBLE. *1

PHANTOM PROTECT

PART PROT = The phantoms that are not protected are switched.

FULL PROT = All phantoms cannot be switched when even one phantom on which protect is set to on, is included.

BUTTON LINK = All phantoms cannot be switched when the protect button is set to on.

PANEL MODE

STAND ALONE = Stand alone panel

MOTHER = Mother panel

DAUGHTER = Daughter panel

PANEL LAYOUT*2

TYPE +NUM. = Selection of X-Y DIRECT = Direct selection*3

BPS = Source button selection*1 KEYPAD = Description selection*1

(Only BKS-R3216 is valid.)

*1 : It is only applicable to BKS-R3216/R1617/R1618/R3219/R3220/R1621.

*2 : It is only applicable to BKS-R3210/R3216.

*3 : BKS-R1607/R1608/R3209/R3210

LEVEL MODE*1

SINGLE = Single level selection

MULTI = Multiple level selection

DEST SELECTION*2

DISABLE = Change of destination from the panel is prohibited.

ENABLE = Change of destination from the panel is allowed.

ILLUMINATION LEVEL*3

Brightness of the button indicator : 1 (dark) to 8 (bright)

MONITOR DESTINATION*3

Enter the name of the destination to be monitored (when the MONI button is selected).

SOURCE OFFSET*3

0 = Use the same source as the destination to be monitored. 1 to 1023 = Use the source at the specified offset.

CONTROL LEVELS*3

When you want to select any specific level from remote

control unit, move the cursor to the desired level and press [Enter]. (When you want to select level-3, move the cursor to the third ??? _??? position and press [Enter].)

??? _??? = : Level selection will not be performed.

Other than ??? _??? : A signal will be switched at the level. When all indications show ??? _???, a signal is switched at the level which is set by the primary station.

*1 : It is only applicable to BKS-R3210/R3216.

*2 : It is only applicable to BKS-R1607/R1617.

*3 : It is only applicable to BKS-R3216/R1617/R1618/R3219/R3220/R1621.

Setting Procedure

1.Select the menu item [Z].

2.The cursor appears in ???DISPLAY MODE = 1???.

Move the cursor to an arbitrary mode and press [Enter] establishes the input mode.

3.Enter a number to select using the ten-keys.

When [Enter] is pressed to confirm the input number, the cursor moves to the next setting item.

When you do not want to change the default value, do not input any number, but press [Enter].

Example of Setting Screen

4.Set the respective items in the same way as the steps 2 and 3.

However, set ???PANEL MODE??? (setting the mother and daughters panels) as follows.

Mother panel :

1)Select ???PANEL MODE = 2??? (mother machine).

2)Press [Enter].

The following contents are displayed on the setting screen.

3)Input the unused BLOCK number of the BLOCK & MOTHER STATION LIST into the ??? *??? column.

4)Press [Enter] to confirm the input contents.

Daughter panel :

1)Select ???PANEL MODE = 3??? (daughter panel).

2)Press [Enter].

The following contents are displayed on the setting screen.

3)Input the mother???s STATION ID number of the BLOCK & MOTHER STATION LIST into the ??? **??? column.

4)Press [Enter].

When the ID number is input correctly, model name of the mother panel appears as shown below.

n

Checksum can be displayed from version V1.10 of the BKS series.

Use checksum to check if the program data is correct, in addition to the version number indication. (The PGM CHECKSUM is mainly used.)

The following three types of checksum are available.

BOOT CHECKSUM=D039

Checksum of the program area that is used for starting up the ROM.

PGM CHECKSUM=630F

Check of the area in which the actual programs are stored.

ROM CHECKSUM=FF68 Checksum of the entire ROM.

Example of Setting Screen

Z : SELECT CONNECTION (DVS-RS1616 only)

Purpose

As for DVS-RS1616, this menu is used to set, ???M??? (controlling side) or ???S??? (controlled side) for each 9-pin connector from 1 to 32.

If a controller is connected to a 9-pin connector, set to (S). If a controlled device is connected to a 9-pin connector, set to (M).

When setting to (S), termination is automatically made.

Setting Procedure

1.Select the menu item [Z].

2.Select a input/output number using the cursor.

3.Press [Enter], the setting status changes. (???M??? ??? ???S??? ??? ???M???)

4.Press [S] (TABLE SET), the content now appeared is copied to the table data.

5.Press [Ctrl] _[E] to stop the display and the menu screen of the secondary station will be displayed.

Example of Setting Screen

n

Unless pressing [S], the setting will be ignore.

5-46

Z : SWITCHING FIELD (HDS-V3232 only)

Purpose

This menu is used to set the crosspoint switching field of HDS-V3232 with the control terminal.

Setting Procedure

1.Select the menu item [Z].

2.Press [Ctrl] _[E] to stop the display and the menu screen of the secondary station will be displayed.

???

Example of Setting Screen

n

Unless pressing [S], the data will be deleted when the power is turned off.

Operating Function Key

[F2] : FIELD (Mode which sets the crosspoint switching field)

1.Press [F2]. The cursor will move to ???SWITCH ING FIELD??? in the menu.

2.Press [Enter]. The setting will change. (ODD ??? EVEN ??? FIELD ??? ASYNC ??? ODD)

All switching field in the switcher are deter mined by this setting.

n

To use RS-422A and S-BUS together, set the switching field as follows.

1 When using the S-BUS and CART protocol together :

ODD

2When using the S-BUS and PRODUCTION SWITCHER protocol together : FIELD

Note that the switching timing of the CART will not be accurate if the CART and PRODUCTION SWITCHERS protocols are used together.

Switching timing is not guaranteed in the combination of different switching fields.

For details of the signal switching timing, refer to ???5-8. Signal Switching Timing???.

ROUTING SWITCHER SYSTEM (E)

5-3. Setting Items of the Primary Station on Monitor S-BUS (BKDS-V3292B only)

Used for setting the units on the monitor S-BUS.

Menu Screen of the Primary Station on Monitor S-BUS

Setting Procedure of Monitor Function

1.Select the menu item [R] of the primary station in order to call the menu screen of the secondary station set as the primary station on the monitor S-BUS.

2.Select the menu item [M] to call the menu screen of the primary station on the monitor S-BUS.

3.Set the menu item [F] and [M].

4.Select the menu item [R] to call the secondary station on the monitor S-BUS.

5.Set each menu item on the screen.

6.Press [Ctrl] _[Z] to return to the menu screen of the primary station on the monitor S-BUS.

7.Set each item of all secondary stations, repeating the procedure of step 4 to 6.

8.Press [Ctrl] _[D] to return to the menu screen of the primary station on the standard S-BUS.

n

If there are multiple monitor S-BUS data links, repeat the procedure of step 1 to 8 for each link.

F : SET ACTIVE UNIT NUMBER

Purpose

This menu is used to enable the units connected to the data link of the monitor S-BUS to communicate.

Setting Procedure

1.Select menu item [F].

2.Select the secondary station using the cursor whose communication will be valid.

3.When [Enter] is pressed, the setting displayed will change ???E??? ??? ???Blank??? ??? ???E???. Only the secondary

stations displayed with ???E??? are valid. (???M??? indicates the primary station.)

4.When [Ctrl] _[E] is pressed, the menu screen of the primary station on the monitor S-BUS will be dis- played.

n

As the response will become slower if there are many secondary stations, make the secondary stations not connected invalid.

??? *??? indicates out of the control area.

Example of Setting Screen

m

1.Station ID of the primary station is always 1 regardless of the DIP switch setting on the CPU board.

2.Station ID of the secondary station is deter mined with the DIP switch setting. Do not assign the same number on two or more units as station ID on both standard S-BUS and monitor S-BUS.

Number that can be registered as secondary s station ID are 2 to 254.

M: SELECT MONITOR FUNCTION

Purpose

This menu is for setting the connection to use the input monitor and output monitor in series or independently. To monitor the input and output monitor lines using separate monitors, set the SEPARATED mode. To monitor them together on one monitor, set the COM- BINED mode.

Setting Procedure

1.Select menu item [M]. The following appears.

COMBINED : series connection

SEPARATED : independent use

2.Press [Ctrl] _[E] to display the menu screen of the primary station on the monitor S-BUS.

R : CALL SECONDARY STATION

Purpose

This menu is used to call the secondary station on the monitor S-BUS.

Setting Procedure

1.Select menu item [R].

2.Enter the station number using the numerical keys, and press [Enter] to call it.

3.The menu screen of the secondary station on the monitor S-BUS will be displayed.

5-4. Setting Items of the Secondary Station on Monitor S-BUS (BKDS-V3293B only)

M:SET AVAILABLE MONITOR LINE (DVS-V3232B/V6464B +BKDS-R3292B)

M: SET AVAILABLE MONITOR LINE INPUT=( ENABLE )OUTPUT=( ENABLE )???

???

???

Ctrl-Z:RETURN

Menu Screen of the Secondary Station on Monitor S-BUS (DVS-V3232B/V6464B)

Purpose

This menu is used to set the input monitor and output monitor to valid or invalid.

Setting Procedure

1.Select menu item [M].

2.Select the source/destination using the cursor, and press [Enter] to change the setting. (???ENABLE??? ??? ???DISABLE??? ??? ???ENABLE???)

3.Press [Ctrl] _[Z] to display the menu screen of the primary station on the monitor S-BUS.

n

Be sure to set the monitor line to ???DISABLE??? in cascade connection.

If set to ???ENABLE???, the monitor may not be performed properly.

L : COPY TABLE DATA <MONITOR MENU>

Purpose

This menu is used to copy the setting contents of the remote control unit. This is applied to BKS-R3204 and BKS-R3205.

Setting Procedure

1.Select menu item [L]. This item can be selected from both the menu and another setting screen.

2.The message ???Station Number???? will be displayed. Enter the station number to be copied.

3.When [Enter] is pressed, the table data will be copied

and the screen will return to the setting screen. When [Ctrl] _[E] is pressed again, the menu screen

of the secondary station on the monitor S-BUS will be displayed.

4.When [Ctrl] _[Z] is pressed, menu screen of the primary station on the monitor S-BUS will be dis- played.

Station Number ????

???

Ctrl-E:MENU Ctrl-Z:RETURN

Example of Setting Screen

Data set on the menu item [N : SET PANEL TABLE] are copied.

Purpose

This menu is used to assign source/destination name to each source/destination selection button.

In the monitor mode, the button color of the remote control unit will be green for both source and destination.

Setting Procedure

1.Select menu item [N].

2.Select a button number using the cursor.

3.When [Enter] is pressed, the name can be typed. To delete the registration, press [Enter] before

inputting the name.

4.a) When [J : NAME STYLE (Type +Num)] is

selected in the primary station menu, input the type name (between 0 and F) and the number for the source and destination.

b)Each time [Ctrl] _[N] is pressed when [J : NAME STYLE (DESCRIP. NAME)] is selected in the primary station menu, the following input modes will be switched alternately.

Description name input mode :

When ???Ctrl N: Type +Num??? is displayed on the

screen, it means that the name mode will be changed to ???Type + Number??? by pressing [Ctrl] _[N].

Inputs the Description name from the first to seventh characters with alphabet and numerical keys.

???Type +Number??? name input mode : Same as a)

n

If the Description name has been set for the input/output number the display of Description has priority to the display of ???Type +Number??? even if the ???Type +Number??? name is input.

5.When [Enter] is pressed, the source name is set.

6.When [Ctrl] _[E] is pressed, the screen will return to the menu screen of the secondary station on the

monitor S-BUS.

When [Ctrl] _[Z] is pressed, the screen will return to the menu screen of the primary station on the monitor

S-BUS.

When [Ctrl] _[D] is pressed, the screen will return to the menu screen of the primary station on the standard S-BUS.

Example of Setting Screen

m

1.Set the table data of BKS-R3204/R3205/R3206 by eight buttons previously in the menu item [Z : SET

____PANEL STATUS]. If ???KEY = ____??? is displayed on the key number position, the name can not be input.

2.Be sure to set either source or destination on the respective buttons (keys) when setting the BKS- R1607/R1608/R3209/R3210.

If both source and destination are set to the same button (key), it will cause malfunction.

3.When setting description names to the source/destina- tion buttons, select a name from the description name group sent to the remote control unit.

If other names are input, these will not be set even if the [Enter] button is pressed.

In such cases, transfer the group including the desired description name from the primary station.

In BKS-R1607 of version V1.10 and higher, any desired button among the sixteen buttons can be set as a TAKE button.

When this setting is performed, the name selected by the SELECTOR knob on the front panel can be taken by pressing the TAKE button.

(Maximum inputs 512 xoutputs 512)

The actual setting procedure is as follows. Select a key from the source side which you want to use as the TAKE button. Press the [T] button.

Example of Setting Screen

Purpose

Check the groups and their names of the description names that are transferred from the primary station.

Check Procedure

1.Press either [Enter] or [SPACE] to view the next page.

2.Press either [BS] or [DEL] to view the previous page.

3.Press [Ctrl] _[E] to return to the menu screen of the

secondary station.

Press [Ctrl] _[D] to return to the menu screen of the primary station.

n

In BKS-R1607/R1608/R3209/R3210 of version V1.10 and higher, the 160 description names that are transferred from the primary station can be registered in the range of inputs 512 xoutputs 512 in the order of terminal number regard- less of the block number. When you want to use more than 160 of the description names, transmit the names from the primary station after dividing the description names into several blocks.

The following operations are possible from the screen. Look at destination from source side : [*] key Look at source from destination side : [&] key

Example of Setting Screen

Z : SET PANEL STATUS (BKS-R1607/R1608/ R3204/R3205/R3209/R3210)

<MONITOR MENU> Purpose

Set the various modes of the remote control unit.

Number of sources and destinations that can be controlled from the remote control unit, can be expanded by connect- ing multiple mother and daughter panels. Setting the mother and daughter panels are also performed using this menu. (Ten mother panels can be registered at the maxi- mum.)

The setting contents are as follows.

DISPLAY MODE

STATUS= Displays the status of the primary station crosspoint table.

PROMPT= The pressed buttons lit immediately.

PROTECT MODE

ON AIR= Execute switching from the panel even during the protect mode.

NORMAL= Switching is not possible during the protect mode.

PHANTOM PROTECT

PART PROT= Execute switching on the phantom on which protect is not set.

FULL PROT=Switching is not executed on all phantoms when any of the phantom is set to PRO-

TECT ON.

BUTTON LINK= Switching is not executed on all phantoms when the PROTECT button on the panel is set to ON.

PANEL MODE*3

STAND ALONE= Stand alone panel

MOTHER= Mother panel

DAUGHTER= Daughter panel

PANEL LAYOUT*1

TYPE + NUM.= Selecting X-Y

DIRECT= Selecting direct

LEVEL MODE*1

SINGLE= Selecting a single level

MULTI= Selecting multiple levels

DEST SELECTION*2

DISABLE=The destination change from panel is disabled.

ENABLE=The destination change from panel is enabled.

*1: Applicable to BKS-R3210 only.

*2: Applicable to BKS-R1607 only.

*3: When monitor S-BUS is used, select STAND ALONE= Stand alone machine at all times since mother-daughter setting is not necessary.

Setting Procedure

1.Select menu item [Z].

2.The cursor appears at ???DISPLAY MODE=1.???

Move the cursor to the desired mode. (Use the keys [(], [)].) Press [Enter] to enter the input mode.

3.Input the number to be selected using the numerical

keys.

Press [Enter] to set the input number. The cursor moves to the setting item.

When you want to modify the default value, press [Enter] without inputting any number.

Example of Setting Screen

n

Checksum can be displayed from version V1.10 of the BKS series.

Use checksum to check if the program data is correct, in addition to the version number indication. (The PGM CHECKSUM is mainly used.)

The following three types of checksum are available.

BOOT CHECKSUM=D039

Checksum of the program area that is used for starting up the ROM.

PGM CHECKSUM=630F

Check of the area in which the actual programs are stored.

ROM CHECKSUM=FF68 Checksum of the entire ROM.

Example of Setting Screen

11. Set the test switch (S3) on the CPU-149 board to ???D???.

2. Press the reset switch (S5).

All items of the primary and secondary stations.

11. Set the test switch (S5) on the CPU-256 board to ???D???.

2. Press the reset switch (S1).

All items of the primary and secondary stations.

11. Set the test switch (S2) on the CPU-251 board to ???D???.

2. Press the reset switch (S8).

All items of the primary and secondary stations.

LED Display for Internal Information

LED displays the presence/absence of the signals and setting of the switches independently, irrespective of the self- diagnosis and test mode.

Test Mode Function

Test mode is effective for finding the causes of the error and the faulty sections which have been detected by the self-diagnosis function. It checks LEDs,switches and signal circuit using a rotary switch on CPU board.

6-3. How the Self-Diagnosis Items are Related

6-3. How the Self-Diagnosis Items are Related

Error No. Indicator*1

00 Operating normally

6 * Faulty sync signal detection

4 * Faulty crosspoint hardware

7 * Increase in the switcher's internal temperature/Fan has stopped

2 * Communication error of the REMOTE 1 connector (BNC) /S-BUS

8 * ROM/RAM/EEPROM check error or table deta reading error

1 * Communication error of the REMOTE 2 connector (9-pin) /RS-422A

3 * Communication error of the REMOTE 3 connector (25-pin) /RS-232C

5 * Incorrect setting data of the backup memory

FF Malfunction of CPU board

1990.10.12-15:42 S-BUS LINK DISCONNECTED??? 1990.10.27-09:28 STARTED BY BKS-R1601 Ver3.10 IN STATION 11??? 1990.11.03-05:31 STARTED BY BKS-R3204 Ver3.11 IN STATION 32??? 1991.01.14-13:51 MISSING REFERENCE SIGNAL IN STATION 1??? 1991.02.01-11:15 POWER SUPPLY UNIT B DOWN IN STATION 4??? 1991.02.04-06:11 X-POINT ERROR IN STATION 1

Error message

Error message

A : DISPLAY CONTROL AREA

(DVS-128/HDS-X3000 Series)

Purpose

This menu displays the control size as the primary station.

Example of Display Screen

When LEVEL: 1 to 16 on the [E: SET LEVEL TABLE] screen is set to 1, the message [SOURCE No. 0001-1024 DESTINATION No. 0001-0512 LEVEL 1-16] appears.

There are no input items or set items on this screen.

7-2. Changed Menu (Primary Station Setting Items)

B : SET SOURCE/DEST TYPE

(DVS-128/HDS-X3000 Series)

Purpose

This menu is used to set the type name of the source destination and global phantom table.

The menu makes the management of source/destination easier.

The alphanumeric characters of 4 characters or less can be used. Either 16 type data or the 32 type data can be selected for the terminal numbers of 1 to 512.

Example of Setting Screen

.Every pressing of [F1:TYPE] triggers between TYPE: 16 and TYPE: 32. Either one of the data structures of

the terminal name to be handed by the S-P1, is selected.

.When [F1] is pressed, the message [Do you change the type number? Y or N] appears. When either [Y] or [N]

is pressed, change the setting of the type number.

The terminal name from 1 to 512

. TYPE : 16 The names up to 16 types can be used. When the S-P1 type remote control panel or the UMD is used in the system, select the TYPE 16.

. TYPE : 32 The names up to 32 types can be used. When the S-P1 type remote control panel or the UMD is used in the system, the correct display or correct operation cannot be performed.

The terminal names of No. 513 to 1024 are fixed to type 32 without affected by this setting.

7-2. Changed Menu (Primary Station Setting Items)

E : SET LEVEL TABLE

(DVS-128/HDS-X3000 Series)

Purpose

The level name can be set, and the valid level for each output terminal can be set.

Number of levels of either 8 or 16 can also be selected.

Example of Setting Screen

Every pressing of [F3:LEVEL] toggles between the LEVEL: 1-8 display and the LEVEL: 1-16 display on the 2 nd line.

The LEVEL 9-16 is realized by switching the Destination to which 512 is added, at the same time.

When the system is used with the LEVEL 1-16, the remote control panel that supports the LEVEL 1-16 becomes necessary.

O : SET TIE LINES (DVS-128/HDS-X3000 Series)

Purpose

Change/addition/deletion of the TIE LINE data are per- formed here.

Example of Setting Screen

To set the number, press [Enter] to be ready for number

input. Enter a number in the range of 1 to 1024. When [Enter] is pressed again, the number is set, the range is

checked and duplication of the same number with other setting is checked. Then the number is set.

If duplication of the number is found, the entered number

becomes invalid and the former number remains as it is. To delete a terminal number, press [Enter] without

inputting a numbers. Then ???....??? appears and the terminal number is deleted.

Number of the signals to be set is 254 at the maximum. Number of the TIE LINEs to be set is 16 paths at the maximum.

LEVEL 1

8 8

9

10

10 x10

~

7-2. Changed Menu (Primary Station Setting Items)

7-3. Changed Menu (Secondary Station Setting Items)

S : SET SOURCE ASSIGNMENT

(DVS-128/HDS-X3000 Series)

Purpose

Change/addition/deletion of the MULTIPLE SOURCE name are performed here. When the signal name that has been set as level 1 from the remote control, is supposed to be named as TAKE, the signals whose source numbers are set here, can be selected in the level 2 and later.

Example of Setting Screen

The SOURCE name of LEVEL 1 is fixed in the same way as the source name setting. The SOURCE names of the LEVEL-2 to 8 are set using this screen.

Set the name by entering the Type number first then by

entering the successive three digit number. This name can be deleted using [Ctrl] _[P]. If an illegal name is set, a

message [The name is not defined] appears, the original name is resumed. When a valid SOURCE name has already been input, the name is set, the correspond SOURCE number is internally saved and the cursor moves to the next position.

When ???Enter??? is pressed without entering name, ???....??? appears and the setting is deleted.

7-3. Changed Menu

(Secondary Station Setting Items)

N : SET PANEL TABLE (HDS-X3400)

Purpose

This menu is used to set the switch of the BKS-R3400 (panel switch).

Setting procedure

1.Select the menu item ???N???.

2.Select the desired button number using the cursor.

3.When [Enter] is pressed, the machine enters the channel number input mode. The input mode is canceled if [Enter]

is pressed before inputting the channel number in step 4.

4.Input the channel number of 1 to 16 from the keyboard. The input channel is input by entering a number to the table of the SOURCE side, and the output channel is input by entering a number to the table of the DESTINATION side.

5.Press [Enter] to set the input setting.

6.Press [Ctrl] _[E] to return to the menu screen of the secondary station.

Example of Setting Screen

Operating Function Keys

[F1] : TABLE (Mode which assigns source and destina- tion to the buttons)

This setting is valid for local input/output physical ter- minals of the HDS-X3400. The SOURCE and DESTI- NATION of other unit cannot be set from this button.

[F2] : LED (Mode which adjusts brightness of the button.)

1.Press [F2]. The cursor moves to [LED BRIGHTNESS LEVEL (1-8)] on the screen.

2.Press any key of 1 to 8 from the keyboard.

Brightness of the buttons will change accord- ingly. (dark 1 ??? 8 bright)

n

The BKS-R3400 directly controls only the connected HDS-X3400 regardless of the setting of the primary station, that is different from other remote control units.

ROUTING SWITCHER SYSTEM (E)

7-3. Changed Menu (Secondary Station Setting Items)

V : DISPLAY UNIT STATUS (DVS-128)

Purpose

Purpose is to display the internal status of the equipment.

There are no setting on this screen.

Press [Ctrl] _[E] to return to the menu screen of the secondary station.

Example of Display Screen

Description of contents on display

MAIN or CONNECTOR : VALID/INVALID Displays whether the board (MAIN) to be inserted from the front and the rear connector board, are inserted or not.

STYLE : Analog Video/Analog Audio/Digital Audio Displays the name of the optional signals that are inserted to each option slot.

REFERENCE : A/B

Displays which of the two types of the reference signal, is selected.

REFERENCE SIGNAL : 525/625

Displays the number of lines of the detected reference signal.

SELECT FIELD : ASYNC/ODD/EVEN/FIELD Displays the switching timing of matrix.

POWER SUPPLIES : ON/INVALID

Displays whether the power supply unit is inserted or not.

FANx : ROT/STOP

Displays whether the rear panel fan is rotating or not.

7-7

V : DISPLAY UNIT STATUS (HDS-X3000 Series)

Purpose

Purpose is to display the internal status of the equipment.

There are no setting on this screen.

Press [Ctrl] _[E] to return to the menu screen of the secondary station.

Example of Display Screen (HDS-X3400)

Example of Display Screen (HDS-X3600)

7-8

Example of Display Screen (HDS-X3700)

Description of contents on display

MAIN or CN01-16/CN17-32: HD SDI/SD SDI/HD 0pt8/

INVALID

Displays whether the board (MAIN) to be inserted from the front and the rear connector board (CN01-16/CN17- 32), are inserted or not.

P.S : OK/NG

Displays the power supply status of the MAIN and two CN boards.

REV : REVISION of the boards

REF : A/B

Displays which of the two types of the reference signal is selected.

REFERENCE SIGNAL : 525i/625i/1125i

Displays the number of lines of the detected reference signal.

SELECT FIELD : ASYNC/ODD/EVEN/FIELD/(ASYNC) Displays the switching timing of the matrix.

POWER SUPPLIEDS : ON/INVALID/OVERLOAD Displays the status of the power supply unit. When OVERLOAD is displayed as this status, it means that the excess number of rear optical connectors more than the specified number are installed.

ROUTING SWITCHER SYSTEM (E)

FANA, FANB : ROT/STOP

Displays whether the fan on the matrix board is rotating or not.

FANn : ROT/STOP

Displays whether the fan of the main unit (except the power supply unit) is rotating or not.

FRONT PANEL : BKS-R3400/INVALID

Displays whether the option switch is attached to the front of the HDS-X3400 or not.

n

If the board (MAIN) to be inserted from the front is not installed, the status of the rear connector board is not displayed correctly.

7-3. Changed Menu (Secondary Station Setting Items)

Z : SET SDI FORMAT (HDS-X3000 Series)

Purpose

This menu is used to set the signal format for the output board of the HDS-X3000 series (whether the signal is reclocked in the HD-SDI or not) from the control terminal. This setting becomes valid when the dip switch of the RECLOCK BYPASS of the output board is turned off. When the processor unit of HDS-X3000 series has the SD- SDI output board (HKDS-X3050), the setting of the format is not required.

Setting Procedure

1.Select the menu item ???Z???.

2.Select the desired channel line using the cursor to be set. (The HDS-X3400 will be switched in every four channels, and the HDS-X3600/X3700 will be switched in every eight channels.)

3.When [Enter] is pressed, the setting changes (???HD SDI (RC)??? ??? ???HD SDI (RC PASS)???).

4.Press [S] (Table Set), and the content now on display is copied to the area of SDI FORMAT TABLE.

n

Unless pressing [S] (Table Set), the data will be deleted when the power is turned off.

5.Press [Ctrl] _[E] to stop the display and return to the menu screen of the secondary station.

Example of Setting Screen (HDS-X3400)

7-3. Changed Menu (Secondary Station Setting Items)

Example of Setting Screen (HDS-X3700)

Operating Function Keys

[F1] : FORMAT (Mode in which the HDS-X3400 is set in the units of the four channels and the HDS-X3600/ X3700 is set in the units of the eight channels)

HD SDI (RC) : When the input signal is HD- SDI, the signal is reclocked and is output.)

HD SDI (RC PASS) : The input signal is bypassed and is output as it is.

[F2] : FIELD (Mode which sets the crosspoint switching field)

1.Press [F2]. The cursor moves to ???SWITCH- ING FIELD??? on the screen.

2.Move the cursor to ERF.A ??? REF.B using the

cursor key of the keyboard.

3.Press [Enter]. The status changes as follows. (ODD ??? EVEN ??? FIELD ??? ASYNC ???

ODD ...)

[F3] : REFERE (Mode which selects the reference of the switching timing of the crosspoint in units of the output 32 channels)

1.Press [F3]. The cursor moves to ???REFER- ENCE SELECT??? on the screen.

2.Select a channel using the cursor of the key- board.

3.Press [Enter]. The setting changes. (A ??? B)

n

When using both the CART protocol and S-BUS in RS- 422A, set REFERENCE (switching timing) to A and SWITCHING FIELD to ODD. If other setting is per- formed, the switching timing is sometimes not executed correctly.

In addition, the switching timing is sometimes not execut- ed correctly if SWITCHING FIELD is set in other combi- nations. For more details about the signal switching timings, refer to ???5-8. Signal Switching Timing???.

Purpose

This menu is used to set the format of signals fed to the input/output board of DVS-V3232M and DVS-V6464M with the control terminal.

This setting is available when the REM/LOC switch for the format on each input/output board is OFF.

Setting Procedure

1.Select menu item ???Z???.

2.Select a channel line using the cursor to be set. (The channels will be switched by eight channels. Displayed signal formats that are enclosed by the round brackets as ???(270 Mbps)??? have been set on the board and cannot be modified with the control termi- nal.

3.When [Enter] is pressed, the setting will change (???143 Mbps??? ??? ???117 Mbps??? ??? ???270 Mbps??? ???

???AUTO???).

4.Press [S] (Table Set), and the content now appeared is copied to the area of SDI FORMAT TABLE.

5.Press [Ctrl] _[E] to stop the display and return to the menu screen of the secondary station.

Operating Function Keys

[F1] : FORMAT (Mode which sets the signal format by 8- channels)

[F2] : FIELD (Mode which sets the crosspoint switching field)

1.Press [F2]. The cursor will move to ???SWITCH ING FIELD??? in the menu.

2.Press [Enter]. The setting will change.

(ODD ??? EVEN ??? FIELD ??? ASYNC ??? ODD??????) All switching field in the switcher are deter

mined by this setting.

When a display ???(ASYNC)??? appears on the screen, it indicates that the cross-point selector field has been set in the ASYNC (asynchro- nous) position on the CPU-149 board (S4-1). It means that the setting cannot be changed from the control terminal.

n

To use RS-422A and S-BUS together, set the switching field as follows.

1 When using the S-BUS and CART protocol together :

ODD

2When using the S-BUS and PRODUCTION SWITCHER protocol together : FIELD

Note that the switching timing of the CART will not be accurate if the CART and PRODUCTION SWITCHERS protocols are used together.

Switching timing is not guaranteed in the combination of different switching fields.

For details of the signal switching timing, refer to ???5-8. Signal Switching Timing???.