Sony_Network_Router

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

!WARNUNG

Die Anleitung ist nur f??r qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten d??rfen nur von qualifiziertem Fachpersonal ausgef??hrt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten d??rfen nur von Personen ausgef??hrt werden, die eine spezielle Bef??higung dazu besitzen.

!AVERTISSEMENT

Ce manual est destin?? uniquement aux personnes comp??tentes en charge de l???entretien. Afin de r??duire les risques de d??charge ??lectrique, d???incendie ou de blessure n???effectuer que les r??parations indiqu??es dans le mode d???emploi ?? moins d?????tre qualifi?? pour en effectuer d???autres. Pour toute r??paration faire appel ?? une personne comp??tente uniquement.

Manual Structure

Purpose of this manual

This manual is the installation manual for S-BUS Interface Board BKP-7933.

This manual describes the information items necessary when the unit is supplied and installed.

Relative manuals

Besides this installation manual the following manuals are available for this unit.

.BKP-7933 Maintenance Manual (Available on request)

This manual describes the information items that premise the service based on the components parts such as alignment, schematic diagrams, board layouts and spare parts lists, assuming use of service engineers.If this manual is required, please contact your local Sony Sales Office/Service Center.

.CNU-700 Operation Manual (Supplied with CNU-700)

This manual is necessary for application and operation of CNU-700.

.CNU-700 Maintenance Manual (Supplied with CNU-700)

This manual describes the information items necessary when CNU-700 is supplied and installed, items that premise the service based on the components parts such as schematic diagrams, board layouts and spare parts lists, assuming use of system and service engineers.

.DVS-V1616/A3232B/V6464B/RS1616/TC3232/A3232, BVS-V3232/A3232, HDS-V3232

Installation Manual (for System Setup) (supplied with each unit)

It contains information on the initial settings of the software when installing the above units making up the digital router system.

This manual is intended for system and service engineers, but operators can also refer to it when setting and changing the system.

.BVP-900-series System Manual BKP-9901 (Available on request)

This manual is necessary for connection and operation of CNU-700 and other peripheral equipment, and for setup to control the routing switcher in the HD system.

If this manual is required, please contact your local Sony Sales Office/Service Center.

Trademarks

Trademarks and registered trademarks used in this manual are follows.

.MS-DOS is a registered trademark of Microsoft Corporation.

.Windows is a registered trademark of Microsoft Corporation.

.IBM and AT are registered trademarks of International Business Machine, Inc.

Section 1

Installation

1-1. Checking ROM Version

When the BKP-7933 is installed in the CNU-700, be sure to check that the ROM versions for IC4 and IC5/AT-89 board of the CNU-700 are Ver. 3.00 or higher. If the ROM needs to be replaced, contact your local Sony Sales Office/Service Center.

1-2. Configuration of BKP-7933

The BKP-7933 is composed of the following items.

1-3. Installation Procedure

This section explains briefly on installation procedures. Refer to each section for details.

1-4. Setting Switches on the IF-689 Board

.Be sure make the switches settings for the CNU GROUP No. and S-BUS ID No. before turning on the power. It is no use in setting the switches after turning on the power.

.Do not change the following switches from their factory default settings. S5-8: OFF

S201: 1(ON)

Setting of CNU GROUP No.

S3(CNU GROUP No.)

Set the CNU GROUP No. so that it should be unique in a system.

Factory default setting: 2

Setting Examples

1. When installing the BKP-7933 in the CNU-700 which is provided with the BKP-7930

Set CNU GROUP No. to 2

2. When using the two CNU-700s which are provided with the BKP-7930

CNU-700 (2)

1-4. Setting Switches on the IF-689 Board

Setting of S-BUS ID No.

S12 (S-BUS ID No.)

Set the station address for the unit on the standard S-BUS data link. n

Set to numbers other than 0, 1 and 255.

1(ON)

Setting example

S-BUS ID No.

3: 1 1 0 0 0 0 0 0

64:0 0 0 0 0 0 1 0

Factory default setting: 2

1 2 3 4 5 6 7 8

( indicates the switch lever position)

IF-689 board

S201

S12

(Component side/A side)

1-5. Installation

1-5-1. Installing the IF-689 Board

The unit is equipped with shielding springs which have sharp edges. Do not touch them with bare hands. Pay careful attention when servicing.

1. Loosen the two screws and remove the front panel of the CNU-700.

Screw

Front panel

Screw

2. Insert the IF-689 board in the fourth slot from the top.

IF-689 board

3. Attach the front panel to its original position.

1-6. Connection

1-6-1. Connection Connector/Cable

Connection made with the connector panel during installation or service, should be made with the connectors/complete assemblies specified in the following list, or equivalent parts.

*1: The BNC connector (T bridge) is available to connect the BELDEN 8281 cables. BNC connector (T bridge): 1-764-805-11

*2: The plug needs the following solderless contacts. AWG#18 to #22: 1-566-493-21

AWG#22 to #24: 1-564-774-11

AWG#24 to #30: 1-564-775-11

1-6. Connection

1-6-3. Notes on Connection

To connect the devices to the S-BUS line, refer to Section 1-6-4 and following precautions.

.The cable length of one S-BUS line is a maximum of 500 m (when a BELDEN 8281 or the equivalent is used).

.Be sure to terminate the BNC connector (T bridge) attached to the last machine of the S-BUS line with a 75 Zterminator.

REMOTE S-BUS (BNC connector, male)

BNC Connector (T bridge)

BKP-7933

BELDEN 8281 cable (shorter than 50 cm)

1-6. Connection

1-6-4. Instance of System Configuration

1 CAM

CCA-5

CABLE

2 CAM

3 CAM

TRIAX CCU 3

CABLE

CCA-5

CABLE

CAMERA COMMAND NETWORK UNIT CNU-700

with BKP-7933 (S-BUS INTERFACE)

REMOTE

S-BUS

DIGITAL VIDEO INTERFACE UNIT PFV-D10

ROUTING SWITCHER CONTROLLER BOARD BKPF-R70

CNU CHARACTER

PIX

:VIDEO BNC

:T Bridge

:75 ZTerminator

1-7. Setting Up

The description in this section assumes that the BKPF-R70 is used as the primary station.

1-7-1. Outline

Calling the Menu Display of the Secondary Station

First, call the menu display of the secondary station that is connected to the S-BUS of the primary station.

Procedure

1.Call the SETUP MENU of the primary station by pressing [Ctrl]- [X].

Then, select the menu item ???R:CALL SECONDARY STATION??? and press [ENTER].

Ctrl_X:QUIT SETUP MENU

2.When the message ???CALL STATION NUMBER????

appears, input the S-BUS ID number of the BKP-7933 using the numeric keys and press [ENTER]. The

display changes to the called BKP-7933 menu display.

. If the specified BKP-7933 does not exist on the S- BUS data link, an error is displayed.

Display: ???Station does not exist???

. If the specified BKP-7933 is outside the communi- cation target, an error is displayed.

Check using the menu item ???F:SET ACTIVE UNIT NUMBER???.

Display: ???Disable Station???

Ctrl-D RETURN

1-7. Setting Up

Saving the Setup Data

Press [Ctrl] - [E] to validate and save the setup data and to return to the BKP-7933 menu display. Press [Ctrl] - [D] to return to the BKP-7933 menu display without saving the setup data.

Level Mapping

The level of the routing system can be set in this system. Refer to the installation manual (for system setup) that is supplied with the routing switcher system for an overview of level mapping.

Notes on Setting Up

.Perform the setup for the camera numbers that are actually connected. If setup is performed for camera numbers that are not actually connected, the response speed of the routing switcher may be slowed and the normal function may be hindered. Be sure to set 0 for the camera numbers that are not actually connected.

.When setting up the MODIFICATION COMMAND and the MAINTENANCE COMMAND, do not duplicate the SOURCE No. and the DESTINATION No. when their level settings are the same. If a number is duplicated, the LEVEL No. is automatically set to 0 and the setup is invalidated. The command assignments when shipped from the factory are shown below for reference.

SOURCE No.

DESTINATION No.

ROUTER

PIX1

ROUTER PIX3

ROUTER PIX2(MSU2)

ROUTER PIX2(MSU1)

CAMERA-CCU

CCU-RCP

1-7. Setting Up

1-7-2. Linking the RCP Assignment and VE Monitor Selection

Description of Operation

Set the menu as follows when you want to link the RCP assignment with the VE monitor selection. If this setting is executed, by changing the RCP assignment on the MSU side, the VE monitor that corresponds to the RCP is automatically switched at the same time.

(Example) When the camera that is controlled by RCP1 is changed from CAM1 to CAM5, the video signal on the VE monitor in front of RCP1 is switched at the same time from CAM1 to CAM5.

The contents that are set on this menu are reflected to the ???Setting status of the control system??? of the CNU-700 character display.

(DESTINATION No.)

RCP1 RCP2 RCP3 RCP4

RCP-700 series

RCP5 RCP6

1-7. Setting Up

Setting from the S-BUS Primary Station

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

2.Select either ???A:ROUTER PIX1 ASSIGN??? or

???B:ROUTER WF1 ASSIGN??? using the cursor key and press [ENTER]. (The illustration shows the display

that selects ???A:ROUTER PIX1 ASSIGN???. )

3.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

4.Input the SOURCE No., DESTINATION No. and

LEVEL No. using the numeric keys and press [ENTER]. (The illustration shows the display that

selects ???A:ROUTER PIX1 ASSIGN???. )

. Any number in the range of 1 to 1024 can be selected and set to the SOURCE No. and DESTINA- TION No. without being consecutive.

. LEVEL No. can be freely set, but it cannot be set for each camera number.

1-7. Setting Up

1-7-3. Linking the MSU Camera Selection and the VE Monitor Selection

Description of Operation

Set the menu as follows when you want to link the MSU camera selection with the VE monitor selection. If this setting is executed, when the MSU camera select button is pressed, the video signal of the selected camera can be output to the VE monitor. This function is useful especially when the SDI signal is switched.

(DESTINATION No.)

(0013) OUT 13

PIX

(0014) OUT 14

PIX

MSU-700

1-7. Setting Up

Connecting Peripheral Equipment

CCU 1 to 6

RS-232C

S-BUS BNC (BELDEN 8281)

VIDEO BNC

CONTROL TERMINAL

(IBM PC/AT COMPATIBLES)

*If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX or WF connector (PIX 2 or WF 2 connector for the CCU-700A series)

Setting from the S-BUS Primary Station

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

2.Select either ???C:ROUTER PIX2 ASSIGN??? or

???D:ROUTER WF2 ASSIGN??? using the cursor key and press [ENTER]. (The illustration shows the display

that selects ???C:ROUTER PIX2 ASSIGN???. )

3.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

4.Input the SOURCE No., DESTINATION No. and

LEVEL No. using the numeric keys and press [ENTER]. (The illustration shows the display that

selects ???C:ROUTER PIX2 ASSIGN???. )

.Any number in the range of 1 to 1024 can be selected and set to the SOURCE No. and DESTINA- TION No. without being consecutive.

.LEVEL No. can be freely set, but it cannot be set for each camera number.

1-7. Setting Up

1-7-4. Switching the Video on the Preview Monitor with the RCP PREVIEW Switch

RCP must be modified in order to use this function. Refer to Section 1-9, ???Modification of RCP??? for details.

Description of Operation

Set the menu as follows when you want to switch the video on the preview monitor with the RCP PRE- VIEW switch.

The signal (LINE IN signal or on-air video signal) that is selected as the master source, is output normally to the preview monitor. If this setting is executed, the video signal of any camera can be selected when the RCP PREVIEW switch is pressed. This selection can be independently operated without linking with MSU or VCS. (Linked operation becomes possible by setting the mode.)

Connecting Peripheral Equipment

MSU-700

SERIAL *

CCU-700A with BKP-7311 OUTPUT

*If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector

Setting from the S-BUS Primary Station

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

2.Select either ???E:ROUTER PIX3 ASSIGN??? or

???F:ROUTER WF3 ASSIGN??? using the cursor key and press [ENTER]. (The illustration shows the display

that selects ???E:ROUTER PIX3 ASSIGN???. )

3.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

4.Input the SOURCE No. of the master source and each

camera, DESTINATION No. and LEVEL No. using the numeric keys and press [ENTER]. (The illustra-

tion shows the display that selects ???E:ROUTER PIX3 ASSIGN???. )

. Any number in the range of 1 to 1024 can be selected and set to the SOURCE No. and DESTINA- TION No. without being consecutive.

. LEVEL No. can be freely set, but it cannot be set for each camera number.

1-7. Setting Up

Linking the Preview Monitor Selection with MSU and VCS

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

Ctrl-D RETURN

2.Select the menu item ???H:BKP-7933 MODE??? and press

[ENTER].

3.Move the cursor key to the ???LINK MSU??? of ???2 RCP PREVIEW SWITCH??? and press [ENTER].

. It is linked to the MSU only that is connected to CNU-700 in which the BKP-7933 is installed.

(It is not linked with the MSU that is connected to the CNU IF board BKP-7930, nor with the MSU that is connected to the CNU-700 in which the BKP- 7933 is not installed.)

. The RCP that is connected to the CNU-700 only is validated.

Ctrl-E RETURN TO MENU

1-7. Setting Up

Changing the Operation Mode of the RCP PREVIEW Switch

The operation mode of the RCP PREVIEW switch can be changed on the CNU-700 character display. Use the switches on the AT board inside the CNU-700 for this setting.

SET/CANCEL switch

UP/DOWN switch

MODE switch

1.Set the MODE switch to 5.

The message ???INTERNAL MODE SETTING??? appears on the character monitor display.

2.Set the SET/CANCEL switch to the SET position. The INTERNAL MODE SETTING display appears.

3.Select ???RCP preview MOMENTARY & ALTERNATE??? with the UP/DOWN switch. Set the SET/ CANCEL switch to the SET position.

INTERNAL MODE SETTING

OFF

4.Select the desired operation mode (MON/ALT/ALT1) with the UP/DOWN switch. Set the SET/ CANCEL switch to the SET position. Each operation mode is described below.

MON: The preview display appears only while the RCP PREVIEW switch is being pressed.

ALT: The preview display appears when the RCP PREVIEW switch is pressed once, and disap- pears when it is pressed again.

ALT1: The preview display appears when the RCP PREVIEW switch is pressed once but cannot be turned off.

(If the PREVIEW switch is turned on from another RCP, the preview display can be switched.)

5.Set the MODE switch to 0.

1-7. Setting Up

1-7-5. Executing RCP Assignment from Equipment Other Than MSU

Description of Operation

Set the menu as follows when you want to execute RCP assignment from equipment other than MSU. When this setting is executed, a maximum of 96 x96 CCU-RCP matrix can be set in the matrix space of the S-BUS. The RCP assignment can be set from a remote control unit such as BKS-R3202. (However, setting cannot be made across two or more CNUs.) The setup data of the RCP assignment that is made here is saved in the BKP-7933 side.)

.The contents of the settings that are made using this menu are reflected in the ???Setting status of the control system??? of the CNU-700 character display.

BVP-500/700/900 series CCU-700A (SOURCE No.) CCU-RCP MATRIX

CCU 1

CNU 1

RCP-700 series

* shows an area where the SOUCE No. and DESTINATION No. cannot be set.

1-7. Setting Up

Setting from the S-BUS Primary Station

1.Select the menu item ???B:SET UNIT LOCATION (CCU-RCP)??? and press [ENTER].

2.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

3.Input the SOURCE No., DESTINATION No. and

LEVEL No. using the numeric keys and press

[ENTER].

. Up to 96 in the range of 1 to 1024 can be selected and set to the SOURCE No. and DESTINATION No., but the numbers must be consecutive.

. Any number in the range of 1 to 8 can be set to the LEVEL No. This setting can be assigned to the respective level and can be mapped.

Ctrl-E RETURN TO MENU

1-7. Setting Up

1-7-6. Switching the MSU Camera Selection Externally

Description of Operation

Set the menu as follows when you want to switch the MSU camera selection from a remote location. When this setting is executed, each one of up to 16 MSUs can be specified to control a certain camera.

Connecting Peripheral Equipment

CCU 1 to 6

RS-232C

S-BUS BNC (BELDEN 8281)

VIDEO BNC

CONTROL TERMINAL

(IBM PC/AT COMPATIBLES)

*If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector

1-7. Setting Up

Setting from the S-BUS Primary Station

1.Select the menu item ???C:SET UNIT LOCATION (MSU)??? and press [ENTER].

2.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

3.Input the SOURCE No., DESTINATION No. and

LEVEL No. using the numeric keys and press

[ENTER].

. Any number in the range of 1 to 1024 can be set to the SOURCE No. and the DESTINATION No.

UP to 96 of the SOURCE No. (maximum number of cameras) and up to 16 of the DESTINATION No. (maximum number of MSUs) can be selected.

. Any number in the range of 1 to 8 can be set to the LEVEL No. This setting can be assigned to the respective level and can be mapped.

Ctrl-E RETURN TO MENU

1-7. Setting Up

1-7-7. Changing the Camera Assignment Virtually

Description of Operation

Set the menu as follows when you want to change the camera assignment virtually. When this setting is executed, the camera assignment can be changed virtually without changing the cable connection be- tween the cameras and CCUs. However, the tally numbers and the MSU camera select numbers cannot be changed.

When the SOURCE NAME is set for each camera number, the name can be output to the CNU character displays (from page 2 to page 11) of the CNU-700 with BKP-7933 installed.

Setting from the S-BUS Primary Station

1.Select the menu item ???A:SET UNIT LOCATION (CAM-CCU)??? and press [ENTER].

2.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

3.Input the SOURCE No., DESTINATION No. and

LEVEL No. using the numeric keys and press

[ENTER].

. Up to 96 in the range of 1 to 1024 can be selected and set to the SOURCE No. and the DESTINATION No., but the numbers must be consecutive.

. Any number in the range of 1 to 8 can be set to the LEVEL No. This setting can be assigned to the respective level and can be mapped.

Ctrl-E RETURN TO MENU

1-7. Setting Up

Displaying the SOURCE NAME on the CNU Character Display

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

Ctrl-D RETURN

2.Select ???H: BKP-7933 MODE??? using the cursor key and press [ENTER].

3.Select ???SOURCE NAME??? of ???3 CAMERA No??? with the cursor key and press [ENTER].

Ctrl-E RETURN TO MENU

1-7. Setting Up

1-7-8. Using the Tally System

Description of Operation

Set the menu as follows when you want to construct a tally system using the S-BUS. When this setting is executed, the red tally and the green tally signals are accepted through the S-BUS and are output to the corresponding CCU and camera in the form of command signals. Do not connect any cable to the TALLY connector of the CCU. However, be careful when using the tally system as the response speed of the tally system may become slower.

.When you want to use the green tally lamp on the front panel of the CCU, the CCU needs to be modi- fied. Refer to the maintenance manual separately available.

.Refer to the installation manual of the Tally Interface Unit BKDS-7700, Section 3-2-4, ???Tally Configu- ration??? for details of the tally system.

Connecting Peripheral Equipment

PRIMARY

STATION

CNU-700

with BKP-7933

CCU 1 to 6

DIGITAL VIDEO SWITCHER

SWITCHER DVS-7000

CCA-5

CABLE

S-BUS BNC (BELDEN 8281)

1-7. Setting Up

Setting from the S-BUS Primary Station

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

2.Select ???G: S-BUS TALLY??? using the cursor key and press [ENTER].

3.Move the cursor key to the desired position to be changed and press [ENTER]. (The display enters the

input mode.)

4.Input the SOURCE No. using the numeric keys and press [ENTER]. At this time, assign the SOURCE

No. that has already been set by the system, to the camera number.

. Any number in the range of 1 to 512 can be set.

. Up to four group tallies can be set.

. The installation shows the display on which the tally signal of the SOURCE No. 0001 is assigned to the Camera No.1.

1-7. Setting Up

1-7-9. Displaying the Self-diagnostic Information on the Terminal

Description of Operation

Set the menu as follows when you want to display the self-diagnostic information on the display. When this setting is executed, the status of the self-diagnostics is displayed on the terminal when the self- diagnostic information of the camera or CCU changes. The log of the self-diagnostic information can be checked by selecting ???W: SYSTEM STATUS LOG??? on the BKPF-R70 menu display.

Setting from the S-BUS Primary Station

1.Select the menu item ???Z:BKP-7933 CONFIGURA- TION??? and press [ENTER].

2.Select the menu item ???H: BKP-7933 MODE??? and press [ENTER].

3.Set the ???4 DIAGNOSIS DISPLAY??? to the ON posi- tion using the cursor key and press [ENTER].

Ctrl-E RETURN TO MENU

1-7. Setting Up

1-7-10. Returning the Setups of the MODIFICATION COMMAND to the Factory Default Values

1.Select ???K: RESET TO DEFAULT TABLE??? using the cursor key and press [ENTER].

2.The message ???Reset to Default table???? appears in the

bottom right of the screen. Select ???Y??? and press

[ENTER].

Ctrl-D RETURN

1-7-11. Returning the Setups of the MAINTENANCE COMMAND to the Factory

Default Values

1.Establish the following setup of the switch S2 on the IF-689 board depending upon the type (analog/digital) of routing switcher.

S2-1:

When the analog routing switcher (BVS-V3232) is used

???ON

When the digital routing switcher (DVS-V1616) is used ??? OFF

S2-2 to S2-8: OFF

2. Set the switch S5 on the IF-689 board as shown below.

3.Turn on the main power of the CNU-700, or press the RESET switch S1.

All data is initialized in about five seconds.

IF-689 board

(Component side/A side)

4. Set the switch S5 to the factory default position.

1-7. Setting Up

1-7-12. Connecting 13 or More Cameras

An example of connecting 13 or more cameras is shown below. Two CNU-700s are necessary for connecting 13 or more cameras. (To connect 19 or more cameras, two CNU-700s containing the CNU IF board BKP-7930 are necessary. If you want to connect 25 or more cameras, contact your local Sony Sales Office/Service Center.

CCU 1 to 12

S-BUS BNC (BELDEN 8281)

VIDEO BNC

*If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector

1-8. Data Backup/Restore

. The description in this section assumes that BKPF-R70 is used as the primary station.

.The setup data of the unit is backed up and restored by using the BZR-10 (software for data backup) supplied with the BKPF-R70.

.In this section, a lower-case letter is used in the sample screens. If you want, you can type with a capital letter unless otherwise specified. Not type quotation marks (??? ???) but only 1 when the procedure describes as follows; Type ???1???.

The sample screens use roman letters, boldface letters, and symbols according to the follows.

1-8-1. Installing the BZR-10

BZR-10 operates on the MS-DOS version 6.2 or in the DOS mode of Windows95.

Use the IBM PC/AT compatible personal computer in which the terminal software has been already installed.

1.Insert the BZR-10 floppy disk (abbreviated as FD hereafter) in an FD drive of a personal computer.

2.Select the FD drive (Which is ???A??? drive in this document) in which the BZR-10 FD is inserted. C:\>a:"

3.Type as follows. The BZR-10 software is installed to the hard disk.

A:\>install c:"

4.Type as follows. The mode enters the EDIT command.

Type ???c:\router>??? at the end of PATH. The PATH is added to AUTOEXEC.BAT file. A:\>c:"

C:\ROUTER> cd\.."

C:\>edit autoexec.bat"

PATH C:\;C: ??? ;c:\router

5.Save the AUTOEXEC.BAT file. Quit the edit command.

6.Remove the FD from the disk drive.

7.Use the Ctrl-Alt-Del key combination. The personal computer restarts.

1-8. Data Backup/Restore

1-8-2. Data Backup (Uploading)

For the details of the menu screen and the setting procedure in terminal mode, refer to the installation manual for system setup of ROUTING SWITCHER SYSTEM.

For obtaining the installation manual of ROUTING SWITCHER SYSTEM, contact your local Sony Sales Office/Service Center.

1.Install the BZR-10 software. (Refer to Section 1-8-1.)

2.Connect a personal computer to the REMOTE 3 port of the BKPF-R70 with an RS-232C cross cable (9-pin to 9-pin).

3.Set the TERM/ISR switch S2-3 on the CPU-256 board of the BKPF-R70 to OFF (TERM).

4.Turn on the power of all the equipment on the S-BUS data link.

5.Turn on the power of the personal computer.

6.Start up the terminal software of the personal computer.

7.Use the Ctrl-x key combination.

The menu screen of the primary station is displayed.

Ctrl_X:QUIT SETUP MENU

8.Select ???Z:SET UNIT DETECTABLE??? and change the settings of the secondary stations required to be backed up to enable.

(1)Move the cursor under the ID number of the BKP-7933.

(2)Press the Enter key. Question mark ??????? turns on.

Question mark ??????? means the unit is enabled. When the Enter key is pressed again, question mark ??????? disappears.

9.Use the Ctrl-e key combination. Next, use the Ctrl-x key combination. Return to the menu screen of the primary station.

10.Quit the terminal software.

11.Insert the formatted FD in the disk drive of the personal computer.

12.Type as follows.

C:\>a:" A:\>*"

Type ???a??? or ???a1???. n

???a??? or ???a1??? is the command to start up the backup software.

Type ???a??? or ???a1??? according to the baud rate setting of S2-4 on the CPU-256 board of the BKPF-R70.

a: When S2-4 is set to ON (The baud rate is 9600 bps)

a1: When S2-4 is set to OFF (The baud rate is 38400 bps)

1-36 (E)

BKP-7933

1-8. Data Backup/Restore

13.Type ???1??? at the Function menu. (???1. RECEIVE??? is selected.) The display changes to the Execution menu screen.

14.To back up the data of the BKP-7933, type ???2???. (???2. The data of secondary stations??? is selected.) The data is backed up in the FD.

15.Type ???9??? twice. (???9. Quit??? is selected.) The backup mode is terminated.

16.Start up the terminal software.

17.Use the Ctrl-x key combination.

The display changes to the menu screen of the primary station.

18.Select ???Z : SET UNIT DETECTABLE??? and return the settings of the secondary stations to the previous settings.

19.Quit the terminal software.

1-8. Data Backup/Restore

1-8-3. Data Restore (Downloading)

After the BZR-10 is installed according to Section 1-8-1, perform the following procedures.

1.Insert the FD on which the data is stored in an FD drive of the personal computer.

2.Type as follows.

C:\>a:"

A \>*"

Type ???a??? or ???a1???.

???a??? or ???a1??? is the command to start up the backup software.

Type ???a??? or ???a1??? according to the baud rate setting of S2-4 on the CPU-256 board of the BKPF-R70. a: When S2-4 is set to ON (The baud rate is 9600 bps)

a1: When S2-4 is set to OFF (The baud rate is 38400 bps)

3.Type ???3??? at the Function menu. (???3. SEND??? is selected.) The display changes to the Execution menu screen.

4.To restore the data of the BKP-7933, type ???2???. (???2. The data of secondary stations ??? is selected.)

5.Type ???9??? twice. (???9. Quit??? is selected.) The backup mode is terminated.

1-9. Modification of RCP

The video on the preview monitor can be selected by the PREVIEW switch of the RCP-700/701/720/721/ 730/731. (Refer to section 1-7-4 for details.)

However, version check of the ROM that is installed in the board of the RCP side, and modification of the board in the RCP are required.

If you want to switch the video on the preview monitor using the RCP-740/741, contact your local Sony Sales Office/Service Center.

1-9-1. Checking ROM Version

Be sure to check that the ROM version for the MPU board of the RCP side is Ver. 2.00 or higher. When the ROM needs to be replaced, contact your local Sony Sales Office/Service Center.

1-9-2. Modification of RCP-700/701

After this modification is implemented, the PREVIEW switch of the RCP-701 does not turn on even if it is pressed.

Required Parts

Modification Procedure (SW-752 Board)

1.Remove Q35 and Q36.

2.Cut the printed foil pattern between Q35 base and pin-18/IC4. (1)

3.Cut the printed foil pattern between Q35 emitter and Q34 emitter. (2)

4.Connect the three jumper wires by soldering. Between pin-2/CN4 and pin-50/IC1 (3) Between pin-5/CN5 and Q35 emitter (4) Between Q35 collector and D1 anode (5)

5.Connect a diode 1SS300-TE85L to the soldering land of Q35 by soldering.

Setting Switch on MPU-92 Board

S4-2/MPU-92 board ??? ON

1-9. Modification of RCP

1-9-3. Modification of RCP-720

Required Part

Modification Procedure

1.Connect the two jumper wires by soldering. (SW-754 board) Between pin-6/CN3 and D25 cathode (1)

Between pin-5/CN3 and pin-2/S24 (2)

2.Disconnect CN101/CN-1187 board.

Setting Switch on MPU-92 Board

S4-7/MPU-79 board ??? ON

1-9. Modification of RCP

1-9-4. Modification of RCP-721

Required Parts

Modification Procedure (SW-752 Board)

1.Remove the resistors R10 and R55/SW-755 board.

2.Connect a metal resistor 82 Zto the soldering land of R10, by soldering.

3.Connect the four jumper wires by soldering to the following locations. (SW-755 board) Between pin-3/CN2 and D25 cathode (1)

Between pin-4/CN2 and pin-2/S24 (2) Between pin-2/CN2 and pin-3/S36 (3) Between pin-1/CN2 and R55 (4)

4.Disconnect CN101/CN-1187 board.

Setting Switch on MPU-92 Board

S4-7/MPU-79 board ??? ON

1-9. Modification of RCP

1-9-5. Modification of RCP-730/731

Required Parts

Modification Procedure (SW-893 Board)

1.Remove soldering of R1, R2, R3 and R12.

2.Connect metal resistors 0 Zto the soldering land of R4, R6 and R7 by soldering.

3.Connect metal resistors 82 Zto the soldering land of R5 by soldering.

Setting Switch on MPU-92 Board

S4-7/MPU-79 board ??? ON

1-10. Using the BKP-7933 in the HD System

Connecting Peripheral Equipment

CAMERA COMMAND

NETWORK UNIT

CNU-700

I/O PORT

1-10-1. Controlling the Routing Switcher via the RS-422A Interface

The routing switcher can be controlled via the RS-422A interface. Modify the AT-89 board of the CNU- 700, replace ROM of the MSU and make the MSU assignment referring to the following description.

Required Parts

1-10. Using the BKP-7933 in the HD System

Modification of AT-89 Board

1.Connect a jumper wire between B7 pin/CN2 and B9 pin/CN2 of the AT-89 board of the CNU-700 by soldering.

2.Remove the six screws and remove the rear panel. Remove the harness that is connected to the connector CN12 on the MB-562 board and the connector CN15 on the CN-1001 board. Connect the RS-422 harness that is supplied, instead of the removed harness.

Be careful that the either end of the RS-422 harness has the specified destination of connection.

The following labels are attached to the rear of the housing at both ends. [15] ??? To CN-15/CN-1001 board

[12] ??? To CN-12/MB-562 board

Rear panel

B3 x5

3.Remove the IF-480 board from of the first slot and set the switches as shown below. S802 to S806: Insert a shorting plug between pin-2 and pin-3.

(The command interface is set to RS-422A.) S901-4: ON

S901-5: OFF

S901-6: OFF

(The baud rate is set to 38.4 k bps.) n

There can be a case that the optional IF-480 board has already been installed to the second slot. In such a case, setting the switches on the IF-480 board in the second slot is not necessary. (Switches are invalid even though they are set.)

ROM Replacement of the MSU-700

Replace the IC10 on the CPU-171 board of the MSU-700 with the ROM MSU-700 that is mounted in the IC socket of the ROM-25 board. Refer to the MSU-700 maintenance manual for removal of the CPU- 171 board.

Setting of the MSU Assignment

Set the control mode to the LOCAL MSU mode (LOCAL mode) using the MSU assignment menu. Refer to the BVP-900-series System Manual BKP-9901 (available separately) Section 3-4-3 ???MSU Assignment??? for the setting procedure.

1-10. Using the BKP-7933 in the HD System

1-10-2. Controlling a Waveform Monitor

A waveform monitor can be controlled from the MSU via the I/O PORT connector of the BKP-7933, by setting the switches on the IF-689 board of the BKP-7933.

The following setting is effective to control a waveform monitor from the MSU that is connected to the IF-480 board of the CNU-700 in which the BKP-7933 is installed. A waveform monitor cannot be controlled by the MSU that is connected to the optional IF-480 board (CNU IF board BKP-7930).

1.Set the switch S2-2 on the IF-689 board to OFF.

When it is set to OFF, remote control mode of the waveform monitor is selected.

2.Set the switch S2-3 on the IF-689 board in accordance with a waveform monitor in use. HD ANALOG system waveform monitor (such as Tektronix 1730HD) ??? ON RECALL system waveform monitor ??? OFF

IF-689 board

(Component side/A side)

1-10. Using the BKP-7933 in the HD System

Connection

The wiring diagram of the cable connecting the I/O PORT connector and a waveform monitor is shown below. The wiring diagram can change depending on the system of the waveform monitor.

HD ANALOG system

GND9

33 17 50

LINE/FIELD

RGB EN

RECALL system

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual.

Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.

Le mat??riel contenu dans ce manuel consiste en informations qui sont la propri??t?? de Sony Corporation et sont destin??es exclusivement ?? l???usage des acqu??reurs de l?????quipement d??crit dans ce manuel.

Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des op??rations ou entretiens de l?????quipement ?? moins d???une permission ??crite de Sony Corporation.

Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind, und ausschlie??lich zum Gebrauch durch den K??ufer der in dieser Anleitung beschriebenen Ausr??stung bestimmt sind.

Die Sony Corporation untersagt ausdr??cklich die Vervielf??ltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben f??r irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausr??stung ohne ausdr??ckliche schriftliche Erlaubnis der Sony Corporation.