TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Know Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . 4

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Last Page

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar with your generator. Know its applications, its limitations and any hazards involved.

Every effort has been made to ensure that information in this manual is accurate and current. However, Snapper reserves the right to change, alter or otherwise improve the product and this document at any time without prior notice.

SAFETY RULES

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

The safety alert symbol () is used with a signal word (DANGER, CAUTION,WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION, when used without the alert symbol, indicates a situation that could result in equipment damage. Follow safety messages to avoid or reduce the risk of injury or death.

In the State of California a spark arrester is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. If you equip the muffler with a spark arrester, it must be maintained in effective working order.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

DANGER

Running engine gives off carbon monoxide, an odorless, colorless, poison gas.

Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning.

Breathing carbon monoxide will cause nausea, fainting or death.

???Operate pressure washer ONLY outdoors.

???Use a respirator or mask whenever there is a chance that vapors may be inhaled.

???Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.

WARNING

Spray contact with electrical wiring can result in electrocution.

???Keep water spray away from electric wiring or fatal electric shock may result.

WARNING

Use of pressure washer can create puddles and slippery surfaces.

High pressure spray could cause you to fall if you are too close to the cleaning surface.

???Keep spray nozzle between 8 to 24 inches away from cleaning surface.

???Operate this unit on a stable surface.

???The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces.

???Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

???Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

???Turn pressure washer OFF and let it cool at least 2 minutes before removing gas cap.

???Fill fuel tank outdoors.

???DO NOT overfill tank.Allow space for fuel expansion.

???Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

???DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

???DO NOT tip engine or equipment at angle which causes fuel to spill.

???DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

???Transport/repair with fuel tank EMPTY or with fuel shutoff valve OFF.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

???Store away from furnaces, stoves, water heaters, clothes dryers or other appliances that have pilot light or other ignition source because they can ignite fuel vapors.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

???NEVER aim the spray gun at people, animals or plants.

???DO NOT allow CHILDREN to operate the pressure washer.

???NEVER repair high pressure hose. Replace it.

WARNING

Starter and other rotating parts can entangle hands, hair, clothing, or accessories.

???DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts.

???Tie up long hair and remove jewelry.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

???Always wear eye protection when you use this equipment or when you are in the vicinity where the equipment is in use.

WARNING

Unintentional sparking can result in fire or electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

???Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug.

CAUTION

Excessively high or low operating speeds increase risk of injury and damage to pressure washer.

???DO NOT tamper with governed speed.

???DO NOT operate the pressure washer above the rated pressure.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150??F (65??C).

Severe burns can occur on contact.

???DO NOT touch hot surfaces.

???Allow equipment to cool before touching.

CAUTION

High pressure spray may damage fragile items including glass.

???DO NOT point spray gun at glass when in the jet spray mode.

???NEVER aim the spray gun at plants.

Recoil Starter

Nozzle Extension

High Pressure Hose

Oil Fill

Cap/Dipstick

Adjustable Nozzle ??? Always attached to nozzle extension. Adjustable nozzle allows you to adjust force of spray and spray pattern.

Air Cleaner ??? Dry type filter element limits the amount of dirt and dust that gets in the engine.

Automatic Cool Down System ??? Cycles water through pump when water reaches 125??-155??F. Warm water will discharge from pump onto ground.This system prevents internal pump damage.

Chemical Injection Siphon/Filter ??? Use to siphon detergent or other pressure washer chemicals into the low pressure stream.

DataTag (not shown, near rear of base plate) ???

Provides model, revision and serial number of pressure washer. Please have these readily available if calling for assistance.

Fuel Cap ??? Fill with clean unleaded fuel here.

High Pressure Hose ??? Connect one end to water pump and the other end to spray gun.

High Pressure Outlet ??? Connection for pressure hose.

Nozzle Extension ??? Attach to spray gun to use adjustable nozzle.

Oil Fill Cap/Dipstick ??? Used for checking and adding oil.

Pump ??? Develops high pressure.

Recoil Starter ??? Used for starting the engine manually.

Spray Gun ??? Controls the application of water onto cleaning surface with trigger device. Includes safety latch.

Water Inlet ??? Connection for garden hose.

IMPORTANT: Read entire owner???s manual before you attempt to assemble or operate your new pressure washer.

REMOVE PRESSURE

WASHER FROM

CARTON

???Remove the parts bag included with pressure washer.

???Slice two corners at the end of carton from top to bottom so the panel can be folded down flat, then remove all packing material.

???Remove pressure washer from carton.

Carton Contents

Check all contents.

???Main unit

???Engine Oil

???Safety Goggles

???High Pressure Hose

???Spray Gun

???Nozzle Extension

???Parts Bag (which includes the following):

???Owner???s Manual

???Engine Manual

???Owner???s Registration Card

???Maintenance Kit

???Handle Fastening Hardware Kit (which includes):

???Carriage Bolts (2)

???Plastic Knobs (2)

??????L??? Hooks (2)

???Lock Nuts (2)

To prepare your pressure washer for operation, you will need to perform these tasks:

???Fill out and send in registration card.

???Add oil to the engine crankcase.

???Add fuel to the fuel tank.

???Connect the high pressure hose to the spray gun and the pump.

???Connect the water supply to the pump.

???Attach nozzle extension to spray gun.

Attach Handle

1.Place the handle assembly onto the handle supports connected to the main unit. Make sure the holes in the handle align with the holes on the handle supports (Figure 1).

Figure 1 ??? Attach Handle to Base

Handle

Align Holes

Handle

Supports

NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports.

2.Insert the carriage bolts through the holes from the outside of the unit and attach a plastic knob from the inside of the unit (Figure 2).Tighten by hand.

Figure 2 ??? Secure Handle

If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the pressure washer helpline at 1-800-317-7833. If calling for assistance, please have the model, revision, and serial number from the data tag available.

3.Insert one of the ???L??? hooks through the hole just under the billboard on the left side of the handle (viewing from rear of unit). Hold the hook in place with a pliers and attach the locknut with a

7/16??? wrench (Figure 3).

Figure 3 ??? Attach ???L??? Hooks to Handle

Spray Gun

Hook

Hose Hook

4.Insert the other ???L??? hook through the hole just above the billboard on the right side of the handle (viewing from rear of unit). Hold the hook in place with a pliers and attach the locknut with a 7/16??? wrench (Figure 3).

Add Fuel

WARNING! NEVER fill fuel tank indoors. NEVER fill fuel tank when engine is running or hot.Allow unit to cool for two minutes before refueling. DO NOT light a cigarette or smoke when filling the fuel tank.

WARNING! DO NOT overfill the fuel tank. Always allow room for fuel expansion.

???Place pressure washer on a level surface.

???Refer to engine owners manual to add recommended fuel to engine.

Add Engine Oil

IMPORTANT: Any attempt to crank or start the engine before it has been properly serviced with the recommended oil may result in an engine failure.

???Place pressure washer on a level surface.

???Refer to engine owners manual to add recommended oil to engine.

NOTE: Check Oil Often During Engine Break???in.

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

???Uncoil the high pressure hose and attach one end of the hose to the base of the spray gun (Figure 3).Tighten by hand.

Figure 3 ??? Connect High Pressure Hose to Spray Gun

???Attach the other end of the high pressure hose to the high pressure outlet on the pump (Figure 4).Tighten by hand.

Figure 4 ??? Connect High Pressure Hose to Pump

???Before you connect your garden hose to the water inlet, inspect the inlet screen (Figure 5). Clean the screen if it contains debris or have it replaced if damaged. DO NOT

RUN THE PRESSURE WASHER IF THE SCREEN IS

DAMAGED.

Figure 5 ??? Connect the Garden Hose to Water Inlet

Inspect inlet screen, DO NOT use if damaged; clean if dirty.

???Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100??F).

???Connect the garden hose (not to exceed 50 feet in length) to the water inlet.Tighten by hand (Figure 5).

CAUTION! There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ???Y??? shut-off connector or other convenience-type water shut-off valve. Damage to pressure washer resulting from disregarding this warning will not be covered by the warranty.

???Turn ON the water and squeeze the trigger on the gun to purge the pump system of air and impurities.

CAUTION! Before starting the pressure washer, be sure you are wearing adequate eye protection.

CHECKLIST BEFORE

STARTING ENGINE

Review the unit???s assembly to ensure you have performed all of the following.

???Make sure the handle is in place and secure.

???Check that oil has been added to the proper level in the engine crankcase.

???Add the proper fuel to fuel tank.

???Check for properly tightened hose connections (high pressure and water supply) and that there are no kinks, cuts, or damage to the high pressure hose.

???Provide a proper water supply at an adequate flow.

???Be sure to read "Safety Rules" and "How To Use Your

Pressure Washer" before using the pressure washer.

HOW TO USE YOUR

PRESSURE WASHER

If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-317-7833.

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.

???Place the pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.0 gallons per minute and no less than 20 PSI at the pressure washer end of the garden hose.

???Check that the high pressure hose is tightly connected to the spray gun and to the pump. See ???Preparing Pressure Washer for Use??? for illustrations.

???Make sure unit is in a level position.

???Connect the garden hose to the water inlet on the pressure washer pump. Turn ON the water.

CAUTION! DO NOT run the pump without the water supply connected and turned on.You must follow this caution or the pump will be damaged.

???Squeeze the trigger on the spray gun until you have a steady stream of water.This purges the pump of air and impurities.

???Attach the adjustable nozzle extension to the spray gun (Figure 6).Tighten by hand.

Figure 6 ??? Connect Nozzle Extension to Spray Gun

???Position the nozzle in the low pressure mode (see ???How to Use the Adjustable Nozzle???) and squeeze the trigger on the spray gun to relieve the air pressure caused by turning ON the water.Water will flow out of the spray gun in a thin stream. Continue to hold trigger until there is a steady stream of water and no air remains in the system.This will make it easier to pull start the engine. Release the trigger.

???Engage the safety latch to the spray gun trigger (Figure 7).

Figure 7 ??? Spray Gun with Safety Latch Engaged

Safety Latch

???Start the engine according to instructions given in the engine owner???s manual.

NOTE: Always keep the throttle lever in the ???Fast??? position when operating the pressure washer.

NOTE: If the recoil starter is hard to pull, squeeze the spray gun trigger to relieve internal pump pressure.

How to Stop Your Pressure Washer

???Let the engine idle for two minutes.

???Turn engine off according to instructions given in the engine owner???s manual.

???Squeeze trigger on the spray gun to relieve pressure in the hose.

NOTE: A small amount of water will squirt out when you release the pressure.

How to Use the Adjustable Nozzle

You now should know how to START your pressure washer and how to STOP it.The information in this section will tell you how to adjust the spray pattern and to apply detergent or other cleaning chemicals.

WARNING! NEVER adjust spray pattern when spraying. NEVER put hands in front of nozzle to adjust spray pattern.

???Slide the nozzle forward when you wish to adjust the spray to low pressure mode (Figure 10). Slide the nozzle backward to achieve high pressure.

Figure 10 ??? Adjusting Nozzle for Pressure

???Point the nozzle down towards a firm surface and press the trigger to test the pattern (Figure 11).

Figure 11 ??? Testing the Spray Pattern

???Twisting the nozzle adjusts the spray pattern from a narrow pattern to a fan pattern (Figure 12).

Figure 12 ??? Adjusting the Nozzle for Spray Pattern

???For most effective cleaning, keep spray nozzle from 8 to 24 inches away from cleaning surface.

???If you get the spray nozzle too close, especially using high pressure mode, you may damage the surface being cleaned.

???DO NOT get closer than 6 inches when cleaning tires.

Applying Detergent with the Adjustable Nozzle

IMPORTANT: Use soaps designed specifically for

pressure washers. Household detergents could damage the pump.

CAUTION! You must attach all hoses before you start the engine. Starting the engine without all the hoses connected and without the water turned ON will damage the pump.

To apply detergent, follow these steps:

???Review the use of adjustable nozzles.

???Prepare the detergent solution as required by the job.

???Place the filter end of the detergent siphoning tube into the detergent container.

CAUTION! Keep the detergent siphoning tube from coming in contact with the hot muffler.

???Slide the adjustable nozzle forward to low pressure mode. Detergent cannot be applied with the nozzle in high pressure position.

???Make sure the garden hose is connected to the water inlet. Check that the high pressure hose is connected to the spray gun and the pump. Start the engine.

???Apply the detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

???Allow the detergent to "soak in" for 3-5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow the detergent to dry on (prevents streaking).

IMPORTANT: You must flush the chemical injection system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Pressure Washer Rinsing

WARNING! Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.When you press the trigger, the recoil from the initial spray could cause you to fall.The high pressure spray could also cause you to fall if you are too close to the cleaning surface.

For Rinsing:

???Slide the nozzle backward to high pressure, press the trigger and wait for the detergent to clear.

CAUTION! Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

NOTE: You can also stop detergent from flowing by simply removing detergent siphoning tube from bottle.

???Keep the spray gun a safe distance from the area you plan to spray.

???Apply a high pressure spray to a small area, then check the surface for damage. If no damage is found, it is okay to continue cleaning.

???Start at the top of the area to be rinsed, working down with same overlapping strokes as you used for washing and applying detergent.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach a temperature between 125?????155??F.When the water reaches this temperature, the automatic cool down system engages and cools the pump by discharging the warm water onto the ground. This system prevents internal damage to the pump.

SPECIFICATIONS

Outlet Pressure . . . . . 2300 psi

Flow Rate . . . . . . . . . . 2.0 gallons per minute (gpm)

Detergent . . . . . . . . . . Use detergent approved for pressure washers

Water Supply . . . . . . Not to Exceed 100??F

Temperature

GENERAL MAINTENANCE

RECOMMENDATIONS

The pressure washer warranty does not cover items that have been subjected to operator abuse or negligence.To receive full value from the warranty, the operator must maintain the pressure washer as instructed in this manual.

???Some adjustments will need to be made periodically to properly maintain your pressure washer.

???All maintenance in this manual and the engine owner???s manual should be made at least once each season.

???Once a year you should clean or replace the spark plug, clean or replace the air filter and check the spray gun and adjustable nozzle extension assembly for wear.A new spark plug and clean air filter assure proper fuel-air mixture and help your engine run better and last longer. Please refer to your engine owner???s manual for more details.

???If equipped with inflatable tires, keep the air pressure at the value marked on the tire or within 15 and 40 psi.

Before Each Use

???Check engine oil level.

???Check water inlet screen for damage.

???Check in-line filter for damage.

???Check high pressure hose for leaks.

???Check detergent siphoning tube and filter for damage.

???Check spray gun and adjustable nozzle extension assembly for leaks.

???Rinse out garden hose to flush out debris.

PRESSURE WASHER

MAINTENANCE

Check and Clean Inlet Screen

Examine the screen on the water inlet. Clean it if the screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

WARNING! NEVER repair a high pressure hose. Replace it with another hose that exceeds the maximum pressure rating of your pressure washer.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged.The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

Check Gun and Adjustable Nozzle

Extension

Examine the hose connection to the spray gun and make sure it is secure.Test the trigger by pressing it and making sure it ???springs back??? into place when you release it. Put the safety latch in the ON position and test the trigger.You should not be able to press the trigger.

Purge Pump of Air and

Contaminants

To remove air from the pump, follow these steps:

???Set up the pressure washer as described in ???Preparing Pressure Washer For Use???. Connect the water supply and turn water on.

???Pull the trigger on the spray gun and hold.

???When the water supply is steady and constant, engage the safety latch.

To remove contaminants from the pump, follow these steps:

???Set up the pressure washer as described in ???Preparing Pressure Washer For Use???. Connect the water supply and turn water on.

???Remove the nozzle extension from the spray gun.

???Start the engine according to instructions in ???How To Use Your Pressure Washer???.

???Squeeze the trigger on the spray gun and hold.

???When the water supply is steady and constant, engage the safety latch and refasten the nozzle extension.

Check In-Line Filter

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

???Place the detergent siphoning tube in a bucket full of clean water.

???Slide the adjustable nozzle forward to the low pressure position. Flush for 1-2 minutes.

???Shut off the engine.

IMPORTANT: Simply shutting OFF engine will not release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun to relieve the pressure in the hose.

Refer to Figure 13 and service the in-line filter if it becomes clogged, as follows:

Figure 13 ??? Clean In-Line Filter

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush the screen, spray gun, and adjustable nozzle extension with clean water to clear debris.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a orifice clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the orifice using the tools included with your pressure washer and follow these instructions:

1.Shut off the engine and turn off the water supply.

2.Detach the nozzle extension from the spray gun.Twist the nozzle clockwise to the stream position. Using the supplied 2mm (5/64) allen wrench, remove the orifice from the end of the nozzle extension (Figure 14).

Figure 14 ??? Removing and Cleaning Nozzle

2.If the screen is damaged, the o-ring kit contains a replacement in-line filter screen and an o-ring. If undamaged, reuse screen.

3.Place the in-line filter screen into the threaded end of the nozzle extension. Direction does not matter. Push the screen in with the eraser end of a pencil until it rests flat at the bottom of the opening.Take care to not bend the screen.

4.Place the o-ring into the recess. Push the o-ring snugly against the in-line filter screen.

5.Assemble the nozzle extension to the spray gun, as described earlier in this manual.

3.Remove the in-line filter from the other end of the nozzle extension.

4.Use the wire included in the kit (or a small paper clip) to free any foreign material clogging or restricting the orifice (Figure 14).

5.Using a garden hose, remove additional debris by back flushing water through the nozzle extension

(Figure 15). Back flush between 30 to 60 seconds.Turn the adjustable nozzle extension to stream spray and move the nozzle from low to high while flushing.

Figure 15 ??? Backflushing the Nozzle

6.Reinstall the orifice and in-line filter into the nozzle extension. DO NOT overtighten the orifice with the allen wrench.

7.Reconnect the nozzle extension to the spray gun.

8.Reconnect the water supply, turn on the water, and start the engine.

Change pump oil as follows:

1.Drain engine oil and fuel from pressure washer.

2.Use a 8mm allen wrench to remove the black pump oil cap between the high pressure outlet and garden hose inlet (Figure 17).

Figure 17 - Changing Pump Oil

9.Test the pressure washer by operating with nozzle in the high and in the low positions.

O???Ring Maintenance

Through the normal operation of your pressure washer, o???rings are used to keep the connections of the hoses and spray gun tight and leak???free.These o-rings may become worn or damaged.

An O???Ring Maintenance Kit is provided with your pressure washer. It includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit???s o-rings. Note that you will not use all of the parts in the kit.

To remove a worn or damaged o???ring:

???Use a small flathead screwdriver to get underneath the o-ring and pry it off.

Pump Maintenance

Changing Pump Oil

Change oil every 50 hours or once yearly, whichever occurs first.

NOTE: Purchase a premeasured bottle of pump oil, item number 190586GS, by contacting the nearest authorized service center.

3.Tilt the pressure washer to drain the oil into an approved container until it drips slowly from the pump.

4.Tilt the pressure washer in the opposite direction and empty the premeasured pump oil bottle into the same opening (a small funnel may be helpful).

5.Install the black pump oil cap and tighten firmly.

6.Set the pressure washer in the upright position. Add fuel and engine oil.

ENGINE MAINTENANCE

See the engine owner???s manual for instructions on how to properly maintain the engine.

CAUTION! Avoid prolonged or repeated skin contact with used motor oil. Used motor oil has been shown to cause skin cancer in certain laboratory animals.Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

PREPARING THE UNIT

FOR STORAGE

Water should not remain in the unit for long periods of time. Sediments or minerals can deposit on pump parts and ???freeze??? pump action. If you do not plan to use the pressure washer for more than 30 days, follow this procedure:

1.Flush detergent siphoning tube by placing the filter into a pail of clean water while running pressure washer in low pressure mode (adjustable nozzle in the forward position). Flush for one to two minutes.

2.Shut off the engine and let it cool, then remove high pressure and garden hoses. Disconnect spark plug wire from spark plug.

3.Empty the pump of all pumped liquids by pulling the recoil handle about 6 times.This should remove most of the liquid in the pump.

4.Use PumpSaver to prevent corrosion build up and freezing of pump.

5.Store unit in a clean, dry area.

NOTE: PumpSaver is available as an optional accessory. It is not included with the pressure washer. Contact the nearest authorized service center to purchase PumpSaver.

CAUTION! You must protect your unit from freezing temperatures. Failure to do so will permanently damage your pump and render your unit inoperable. Freeze damage is not covered under warranty.

CAUTION! Read and follow all cautions and warnings on the PumpSaver can label. Always wear eye protection when using PumpSaver.

To use PumpSaver, make sure the pressure washer is turned off and disconnected from supply water. Read and follow all instructions and warnings given on the PumpSaver container.

NOTE: PumpSaver will drip from pump after treatment and will stain wood and concrete.

NOTE: If PumpSaver is not available, draw RV antifreeze (non-alcohol) into the pump by pouring the solution into a 3-foot section of garden hose connected to inlet adapter and pulling recoil handle twice.

Protecting the Pump

To protect the pump from damage caused by mineral deposits or freezing, use PumpSaver to treat pump.This prevents freeze damage and lubricates pistons and seals.

STORING THE ENGINE

See the engine owner???s manual for instructions on how to properly prepare the engine for storage.