Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper.

Ce manuel est imprim?? sur du papier recycl??.

Este manual ha sido impreso sobre papel reciclado. Questo manuale ?? stato stampato su carta da riciclaggio. Denna handbok ??r tryckt p?? recyclingpapper.

Dit handboek werd op recycling-papier gedrukt.

Herausgegeben von/Published by

Fujitsu Siemens Computers GmbH

Bestell-Nr./Order No.: A26361-K864-Z100-1-5E19

Printed in Taiwan

AG 0502 05/02

A26361-K864-Z100-1-5E19

Deutsch

English

463V FA LCD-Bildschirm LCD monitor

Betriebsanleitung

Operating Manual

Ausgabe Mai 2002 May 2002 edition

Introduction

Your new LCD (Liquid Crystal Display) monitor 463V FA offers numerous features and functions, for example:

???TFT display (Thin Film Transistor; active matrix)

???minimal space requirements thanks to slim casing

???optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners)

???high degree of brightness and good contrast

???high resolution (1280x1024) for displaying the information content of a conventional 21-inch screen with CRT (Cathode Ray Tube)

???presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)

???automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates (vertical frequencies) from 56 to 76 Hz (absolutely flicker-free)

???digital screen controller with microprocessor for storing 26 different display modes

???freely adjustable colour alignment for matching the screen colours to the colours of various input and output devices

???convenient operation via integrated OSD (On-Screen-Display) menu

???VESA-DDC compatibility

???VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) - mechanical interface to swivel arm and wall bracket)

???plug&play capability

???power management for reducing power consumption when the computer is not in use

???compliance with the recommendations in accordance with TCO ???99

In normal screen mode (dark characters against a light background) the monitor satisfies the ergonomic requirements for the GS symbol.

This Operating Manual contains important information you require to start up and run your LCD monitor.

A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface is required to control the 463V FA LCD monitor. The monitor processes the data supplied to it by the screen controller. The screen controller/the associated driver software is responsible for setting the modes (resolution and refresh rate).

When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs (see the "Changing the monitor settings" section in the"Operation of the monitor" chapter).

Target group

You don't need to be an "expert" to perform the operations described here. Do, however, read the chapter "Important notes" in the Operating Manual of the computer and in this Operating Manual.

In the event of any problems occurring, please contact your sales outlet or our Help Desk.

Further information

Details of how you set the resolution and refresh rate are provided in the documentation on your screen controller/the associated driver software.

Colour monitor 463V FA

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

?? Text which follows this symbol describes activities that must be performed in the order shown.

"Quotation marks" indicate names of chapters or terms.

Texts in italics indicate filenames and menu items.

Important notes

This device complies with the relevant safety regulations for data processing equipment, including electronic office machines for use in an office environment. If you have any questions, contact your sales outlet or our Help Desk.

???The display surface of the LCD monitor is sensitive to pressure and scratches. You should therefore be careful with the display surface so as to avoid lasting damage (Newton rings, scratches).

???If the device is brought into the installation site from a cold environment, condensation can form. Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site.

???During installation and before operating the device, please observe the instructions on environmental conditions in the "Technical data" chapter as well as the instructions in the "Installing an ergonomic video workstation" chapter.

???To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never be blocked.

???The power adapter automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure that the local mains voltage lies within these limits.

???Ensure that the power socket on the power adapter or the grounded mains outlet is freely accessible.

???The ON/OFF switch does not disconnect the device from the mains voltage. To completely disconnect the mains voltage, remove the power plug from the socket.

???Lay all cables so that nobody can stand on them or trip over them. When attaching the device, observe the relevant notes in the chapter "Connecting the monitor".

Colour monitor 463V FA

???If you use a different data cable from the one supplied, ensure that it is adequately shielded. CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied.

???No data transmission cable should be connected or disconnected during a thunderstorm.

???Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the device (danger of electric shock, short circuit).

???In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign matter), switch off the unit, disconnect the power plug and contact your sales outlet or our Help Desk.

???The screen background lighting contains mercury. You must observe the applicable handling and disposal safety regulations for fluorescent tubes.

???Only qualified technicians should repair the device. Unauthorised opening and incorrect repair may greatly endanger the user (electric shock, fire risk).

???Only use the power adapter supplied or a power adapter of the same type: LSE9901B1260 (Li Shin) or UP06041120A (Potrans).

???The power adapter may only be opened by authorised specialist personnel.

???You may set only those resolutions and refresh rates specified in the "Technical data" chapter. Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or our Help Desk.

???Keep this operating manual together with your device. If you pass on the device to third parties, you should include this manual.

Cleaning

???Always pull out the power plug before you clean the monitor.

???Do not clean any interior parts yourself, leave this job to a service technician.

???Do not use any cleaning agents that contain abrasives or may corrode plastic.

???Ensure that no liquid will run into the system.

???Ensure that the ventilation areas of the monitor are free.

???The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only using a soft, slightly moistened cloth.

Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has been moistened in mild domestic detergent and then carefully wrung out.

Transport

???Transport the monitor with care and only in its original packaging or another corresponding packaging fit to protect it against knocks and jolts.

???Never drop the LCD monitor (danger of glass breakage).

Colour monitor 463V FA

Energy Star Guidelines

The Fujitsu Siemens LCD colour monitor 463V FA is designed to conserve electricity by dropping to less than 3 W when it goes into standby, suspend and OFF mode. With this new power management the 463V FA qualifies for the U.S. Environmental Protection Agency's (EPA) Energy Star Computers award.

The EPA estimates that computer equipment uses 5 percent of all business electricity and that this is growing rapidly. If all desktop computers and peripherals enter a low-power mode when not in use, the overall savings in electricity could amount to $ 2 thousand million annually. These savings could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere - the equivalent of 5 million automobiles.

As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product meets the Energy Star guidelines for energy efficiency.

CE marking

The shipped version of this device complies with the requirements of the EEC directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage directive".

FCC Class B Compliance Statement

The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation.

NOTE:

This equipment has been tested and found to comply with the limits for a "Class B" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference- Causing Equipment Regulations. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between equipment and the receiver.

???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

???Consult the dealer or an experienced radio/TV technician for help.

Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu Siemens Computers GmbH The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC rules.

Colour monitor 463V FA

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Power cable

To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set.

???The female/male receptacles of the cord set must meet CEE-22 requirements.

???The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the outer sheath or on the insulation of one of the inner conductors.

???For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used. For devices which sit on the floor, only SJT type cable sets may be used.

???The cable set must be selected according to the rated current for your device.

Power cable for devices distributed in the US and Canada

In the United States and Canada the cord set must also be UL-listed and CSA-labelled. The voltage rating should be min. 250 volts a.c.

Please consult the following table for the selection criteria for power cables used in the United States and Canada.

Colour monitor 463V FA

Disposal and recycling

This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging. The device may be taken back after use to be recycled, provided that it is returned in a condition that is the result of normal use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.

If you have any questions on disposal, please contact your local office, our Help Desk, or:

Fujitsu Siemens Computers GmbH

Recyclingcenter

D-33106 Paderborn

Tel.: +49 5251 / 81 80 10, Fax: +49 5251 / 81 80 15

Checking the contents of the consignment

??Unpack all the individual parts.

??Check the delivery for damage incurred during transportation.

??Check whether the delivery agrees with the details in the delivery note. The complete LCD monitor package includes:

???one monitor

???one data cable (D-SUB)

???one data cable (DVI-D)

???one power cable

???a power adapter with power adapter cable

???one floppy disk

???one Warranty Booklet

???this Operating Manual

Should you discover that the delivery does not correspond to the delivery note, notify your local sales outlet immediately.

It is recommended not to throw away the original packaging material. Keep it for future i transportation.

Colour monitor 463V FA

Installing an ergonomic video workstation

Before you set up your equipment, you should select a suitable position for working at the monitor. Please observe the following advice when installing a video workstation.

Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available from specialised dealers, may be advisable. For this purpose the monitor base must be removed beforehand as described in chapter "Removing the monitor base".

Connecting the monitor

!notes" at the beginning of this manual.

CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied.

Do not cover the ventilation openings of the monitor. The computer power plug must be pulled out!

??Be sure that the monitor and the computer are switched off.Please note the information provided in the "Safety" section in the chapter "Important

Colour monitor 463V FA

Connecting cables to the monitor

The monitor ports are protected by a cover.

??Remove the cover (1).

The data cables provided have plugs for the D-SUB connector or the DVI-D connector on the monitor.

??Select the suitable data cable for your computer.

Information on the computer connections and interfaces is contained in the operating manual for your computer.

??Connect one of the D-SUB connectors of the data cable to the D-SUB connector on the monitor (3) and secure the plug-in connection by tightening the safety screws.

??Plug the power adapter cable into the power connector (2) of the monitor.

??Firmly insert the socket with the power cable supplied into the power cable connection of the power adapter and check whether the socket is securely seated.

Colour monitor 463V FA

??Mount the cover over the connections again.

Connecting cables to the computer

Information on the computer connections and interfaces is contained in the operating manual for your computer.

??Connect the data cable to the (active) monitor port on the computer and secure the plug-in connection by tightening the safety screws.

??Connect the male receptacle of the power cable supplied to the monitor socket of the computer and ensure a secure connection.

??Plug the power connector of the computer into a properly grounded mains outlet.

When you start working with your monitor for the first time you should install the

i appropriate graphics drivers for your application software. Details of how to do this are provided in the documentation on your screen controller/the associated driver software.

Operation of the monitor

The monitor offers the following possibilities that enable it to be optimally adjusted for the respective user and the respective situation.

Adjusting rake and rotation

The rake of the monitor can be adjusted by ???5?? (forward) and +20?? (back) from its vertical position.

?? Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the desired rake.

The monitor can be rotated by ??? 45?? from its centre position.

?? Grasp the monitor with both hands on the right and left edge of the casing and rotate it into the desired position.

Colour monitor 463V FA

Switching the monitor on/off

1 = Buttons for the OSD menu (On-Screen-Display)

2 = Power indicator

3 = Power button

12 3

The ON/OFF switch (3) is used for switching the monitor on and off.

The power indicator (2) glows green when the monitor and computer are switched on. The power indicator glows orange when the monitor does not receive a video signal or is in the energy-saving mode. The power indicator goes off when the monitor is switched off.

When you switch the computer system on, you must proceed in the following order:

??First switch the LCD monitor on with the ON/OFF switch (3).

??Then switch on the computer.

Notes on power management

If your computer is equipped with power management, the monitor can support this function fully. Here the monitor does not distinguish between the individual energy-saving modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the mode with the highest energy-saving effect.

Colour monitor 463V FA

If your computer detects inactivity (no input) it sends an appropriate signal to the monitor to reduce the power consumption (energy-saving mode). The power indicator of the monitor changes colour to indicate the status change.

Once an input is made at the computer the screen contents are redrawn and full power is restored.

For detailed information on how energy-saving mode operates refer to the Operating Manual or Technical Manual of the computer.

When the monitor is switched to the energy-saving mode by the power management

i system a power consumption of up to 3 W is maintained to feed the circuit for redrawing the screen contents.

To completely switch off the power consumption, switch off the computer or pull the plug of the monitor power cable out of the monitor socket of the computer.

Changing the monitor settings

When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs.

Basic monitor settings with the floppy disk supplied

If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000, Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be set with the floppy disk supplied.

??Insert the supplied floppy disk into the floppy disk drive.

??Open the Readme file on the floppy disk and follow the instructions in the file.

Your monitor should now already be properly adjusted. If none of the above operating systems is used or minor corrections are to be made to the screen display, then change the monitor settings with the OSD menu.

Monitor settings with the buttons of the control panel

Use the buttons of the control panel to make the following monitor settings directly while the OSD menu is switched off.

Colour monitor 463V FA

Performing auto-adjustment of the monitor

?? Press the MENU \ AUTO button for approx. 1 second while the OSD menu is switched off.

The Auto Processing message is displayed.

Picture quality and position are set to optimum values for your system.

Adjusting contrast/background lighting

?? Press the + or ??? button to call the Contrast / Backlight setting window.

This setting window can also be called, when the OSD menu is locked.

Selecting input signal

The monitor can be operated with analogue or digital signals. You can switch between the analogue and the digital mode (depending on the graphics card you use).

??Press the INPUT button to change the mode of the input signal.

Locking the OSD menu

The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.

??Press the MENU \ AUTO button and the + button simultaneously and hold them until the status indicator on the screen is completely filled.

A message is displayed that the action has been performed.

Please proceed in the same manner to release the locked OSD menu again.

Locking the ON/OFF button

The ON/OFF switch can be locked to prevent the monitor from being switched off inadvertently or by an unauthorised person.

??Press the MENU \ AUTO button and the + button simultaneously and hold them until the status indicator on the screen is completely filled.

A message is displayed that the action has been performed.

Please proceed in the same manner to release the locked ON/OFF switch again.

Monitor settings using the OSD menu

With the buttons on the control panel, call up and use the integrated OSD (On-Screen Display) menu.

The OSD menu is available in different languages. The English menu names are used in i the following description (default setting). With the OSD function Language Select in the

Setup Menu you can select another language.

Colour monitor 463V FA

To set the OSD menu, perform the following steps:

?? Briefly press the MENU \ AUTO button to activate the OSD menu.

The main menu appears on the screen with icons for the setting functions.

The first symbol (Auto Image Adjust) is highlighted. At the bottom of the OSD menu each button's function is displayed.

?? Press the - or + button to highlight another icon if necessary (e.g. Manual Image Adjust).

?? Press the INPUT button to select the highlighted icon.

The corresponding setting window (here: Manual Image Adjust) is displayed.

The first symbol (H. / V. Position) is highlighted.

?? If necessary, press the - or + button to mark the next icon.

?? Press the INPUT button to select the highlighted icon.

The icon's colour changes.

?? Press the - or + button to adjust the selected function.

?? Press the MENU \ AUTO button to save the settings.

The icon's colour changes.

?? Press the - or + button to mark another symbol or press the MENU \ AUTO button to return to the main menu.

All changes are stored automatically.

If you want to change other settings, select the corresponding function from the OSD main menu. All possible adjustments of the main menu are described in the following.

The OSD menu for analogue monitor operation is described in the following. During digital i operation some functions are not available, as they are not required due to the digital

transmission technology used.

Colour monitor 463V FA

Performing auto-adjustment

Performing auto-adjustment (Auto Image Adjust)

The Auto Processing message is displayed.

Adjusting the brightness and contrast

Calling the Contrast / Brightness / Backlight setting window.

Setting the contrast of the display (Contrast)

This function allows you to modify the contrast of bright colour tones.

Setting the brightness of the display (Brightness)

This function allows you to modify the contrast of dark colour tones.

Setting the brightness of the background lighting (Backlight)

This function allows you to change the brightness of the entire display.

If the contrast is set too high, bright surfaces can no longer be distinguished from very i bright surfaces. If the contrast is set too low, the maximum brightness will not be

achieved.

Adjusting size and position

Calling the Manual Image Adjust setting window

Adjusting picture position (H./V.Position)

The INPUT button allows you to switch between the H.Position and the

V.Position.

Adjusting the horizontal size (H.Size)

There is an optimum setting for every resolution.

Eliminating picture interference (Fine Tune)

This function enables the fine tuning of your monitor in case of picture interferences.

Adjusting the Zoom

This function allows you to enlarge a section of the display.

Colour monitor 463V FA

Setting colour temperature and colours

Calling the Color Adjust setting window

Selecting colour temperature (Color Temperature)

The "warmth" of the screen colours is set using the colour temperature. The colour temperature is measured in K (= Kelvin). You can select from 9300 K, 6500 K, 5400 K, 5000 K and Native.

Native = original colour of the LCD display

Setting user-defined colours (User Color)

In the user-defined setting you can change the colour ratios of the basic colours (red, green, blue) as required.

Adjusting the intensity of the grey levels (Gamma correction) (Gamma)

This function allows you to optimise the display of multimedia applications.

Linear = default setting

Emphasize Brighter Level = Bright areas remain bright, dark areas become darker

Emphasize Darker Level = Dark areas remain dark, bright areas become brighter

Setting functions in the "Advanced Menu" menu

Calling the Advanced Menu setting window

Setting scaling (Scaling)

1:1 = full picture size (depending on the resolution)

Fill All = switch on the full-screen mode. The display area is stretched to the full picture size (1,280 pixels, side ratio 5:4). As a result, the display may appear distorted.

Fill Aspect Ratio = Switch on the proportional full-screen mode: The display area is expanded to the maximum picture size while maintaining the side ratio (either full picture width or full picture height).

Adjusting the picture quality in case of interpolation (Sharpness)

This function allows you to set the sharpness of the interpolation filter.

Thus the display can be optimised for pictures or texts.

Displaying the monitor information (Information)

This function allows you to display e.g. the current resolution and refresh rate.

Colour monitor 463V FA

Setting functions in the "Setup Menu" menu

Calling the Setup Menu setting window

Selecting input signal (Input Select)

The monitor can be operated with analogue or digital signals. With this function you can (depending on the graphics card you use) switch over between the analogue and the digital mode.

Setting the language for the OSD menu (Language Select)

You can choose from English (default setting), German, French, Italian and Spanish.

Displaying note on resolution (Resolution Notice)

The optimum resolution for this monitor is 1280 x 1024. With the function activated (ON), a message appears on the screen after approx.

30 seconds if a different resolution has been selected.

Setting position for the OSD menu (OSD Position)

You can shift the OSD menu up, down, to the left or to the right.

Setting display time for the OSD menu (OSD Time Out)

You can select a value from 5 to 60 seconds. If the adjusted time has run out without the settings being saved, the OSD menu is automatically closed.

Mode Message ON/OFF

If this function is enabled (ON) a message will be displayed on the screen after approx. 3 seconds when anther mode or another input has been selected.

Setting background for the OSD menu (OSD Background)

ON = normal setting

OFF = transparent

Activating the factory settings

Activating the factory settings (Memory Recall)

The Auto Processing message is displayed. All settings will be reset without questioning.

Colour monitor 463V FA

Notes on ergonomic colour adjustment

If you select colours for the display in your application programmes, take note of the information below.

The primary colours blue and red on a dark background do not produce the minimum required contrast of 3:1 and are therefore not suitable for continuous text and data entry.

When using several colours for characters and background and giving the primary colours full modulation, you can obtain very suitable colour combinations (see the following table):

+Colour combination very suitable

-Colour combination not suitable because colour locations are too close together, thin characters are not identifiable or rigorous focusing is demanded of the human eye.

Colour monitor 463V FA

Removing the monitor base

Before you can use a swivel arm or a wall bracket, you must remove the monitor base:

!The monitor surface is susceptible to scratching!

??Switch off the monitor and pull the power plug out of the power socket.

??Lay the monitor on its face on a soft surface.

??Remove the cover and disconnect all cables.

??Remove the four screws on the rear of the monitor.

You can now mount a swivel arm or a wall bracket as per VESA FPMPMI with 100 mm hole spacing.

For instructions on how to mount the swivel arm or wall bracket, please see the documentation for the swivel arm or wall bracket.

Technical data

Dimensions and weight (LCD monitor)

VESA-DDC-compatible VGA interface

Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video Electronics Standard Association, Display Data Channel) is used as the communications interface between the monitor and the computer. If your computer is equipped with a VESA-DDC-compatible VGA interface, it can automatically read the data for ensuring optimum operation from your monitor and select the appropriate settings.

Colour monitor 463V FA

Preset operating modes

The picture position and size have been set to optimum values at the factory for the i operating modes listed above. Depending on the screen controller used, it may be

necessary to adjust the display position and size. In this case, you can change and save the settings (see "Operation of the monitor").

The following are the most frequently used of the preset operating modes:

For ergonomic reasons, a screen resolution of 1280 x 1024 pixels is recommended. Because of the technology used (active matrix) an LCD monitor provides a totally flicker-free picture even with a refresh rate of 60 Hz.

Pin assignment D-SUB

51

6

10

15 11

Colour monitor 463V FA

Monitor port DVI-D

1

9

17

Trouble shooting

Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer and/or with another data cable.

If you are unable to solve the problem, please inform our Help Desk.

Colour monitor 463V FA

Colour monitor 463V FA