IMPORTANT:

To aid reporting in case of loss or theft, please record the product???s model and serial numbers in the space provided. The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the presence of uninsulated ???dangerous voltage??? within the product???s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

-The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or brightness.

Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.

-Do not display a still picture for a long period, as this could cause a residual image.

-Never rub or tap the monitor with hard objects.

-Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

-This monitor and its accessories may be upgraded without advance notice.

-Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam, as this could lead to fire.

-Ensure that the monitor does not come into contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock.

-Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.

-Do not use the monitor near heating equipment or in places where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.

-Do not use the monitor in places where it may be exposed to direct sunlight.

-Please be sure to constantly remove dust and garbage that has attached to the ventilation opening.

If dust collects in the ventilation opening, it may lead to excessive heat, outbreak of fire, or malfunction.

-As a standard, clean the inside of the monitor once every year. If dust collects inside the monitor, it may lead to excessive heat, outbreak of fire, or malfunction. Please request a cleaning of the inside of the monitor from an authorized SHARP servicing dealer or service center.

-Images cannot be rotated on this monitor.

When using in portrait orientation, you will need to prepare appropriately orientated content in advance.

-The AC outlet shall be installed near the equipment and shall be easily accessible.

The Power Cord

-Use only the power cord supplied with the monitor.

-Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords.

Damage to the cord may result in fire or electric shock.

-Do not use the power cord with a power tap.

Adding an extension cord may lead to fire as a result of overheating.

-Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.

-Unplug the power cord if it is not used for a long time.

-Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.

Manual Scope

-Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.

-HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Licensing LLC.

-DisplayPort is a registered trademark of Video Electronics

Standards Association.

-Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

-This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.

-All other brand and product names are trademarks or registered trademarks of their respective holders.

-Language of OSD menu used in this manual is English by way of example.

-Illustrations in this manual may not exactly represent the actual product or display.

-This manual assumes use in landscape orientation, except where specifically noted.

LED Backlight

???The LED backlight in this product has a limited lifetime. * If the screen gets dark or does not turn on, it may be

necessary to replace the LED backlight.

*This LED backlight is exclusive to this product and must be replaced by an authorized Sharp servicing dealer or service center. Please contact an authorized SHARP servicing dealer or service center for assistance.

Fan

???The fan in this product has a limited lifetime.

???Please contact an authorized SHARP servicing dealer or service center for assistance with fan replacement.

For the monitor in portrait orientation

Operation panel

Do not remove the factory-affixed sticker but affix the logo sticker over it. Be careful not to cover the remote control sensor or buttons.

???This monitor is ???ixed to the temporary stand used in the package for transportation when shipped from the factory. Please note that this stand is for temporary use only until the monitor is properly mounted.

nFront view

1

1.LCD panel

2.Remote control sensor (See page 15.)

3.Input switch (See page 18.)

4.Power switch (See page 16.)

5.Power LED (See page 16.)

TIPS

???Use a pointed object such as a pen tip to press the switches at the front of the monitor.

nRear view

Caution

???Consult your SHARP dealer for attachment/detachment of optional parts.

???Do not block the fan cover.

This terminal is provided for possible future (optional) function expansion. Offering of this terminal is not a guarantee that future expanded functionality will be provided.

15. LAN terminal (See page 12.)

16. RS-232C output terminal (See page 12.) 17. RS-232C input terminal (See page 12.) 18. Audio output terminal (See page 12.)

19. PC/AV D-sub input terminal (See page 11.) 20. PC/AV HDMI1 input terminal (See page 11.) 21. PC/AV HDMI2 input terminal (See page 11.)

Part Names

nRemote control unit

1

1.Signal transmitter

2.POWER button (See page 16.)

3.MUTE button (See page 18.)

4.VOL +/- buttons (See page 18.) BRIGHT +/- buttons (See page 18.)

Cursor control ( / / / ) buttons

5.DISPLAY button (See page 18.)

6.MODE button (See page 18.)

7.INPUT button (See page 18.)

8.MENU button (See page 18.)

9.ENTER button (See page 18.)

10. RETURN button (See page 18.)

11. SIZE button (See page 18.)

1

Caution

???Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected.

???Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.

???Do not use any cable that has a damaged or deformed terminal. Using such cables may cause malfunctions.

TIPS

???Images may not be displayed properly depending on the computer (video card) to be connected.

???Use the automatic screen adjustment when a PC screen is displayed for the first time using D-SUB[RGB] or DVI-I (analog), or when the setting of the PC is changed. The screen is adjusted automatically when SELF ADJUST in the MONITOR menu is set to ON.

???If the audio output from the playback device is connected directly to speakers or other devices, the video on the monitor may appear delayed from the audio portion. Audio should be played through this monitor by connecting the playback device to the monitor???s audio input, and connecting the monitor???s audio output to the speakers or other devices.

???The audio input terminals used in each input mode are factory-set as follows.

13

11

12

10

5

3

4

8 2 9 6 7

Connection with a PC or AV equipment

1. DisplayPort input terminal

???Use a commercially available DisplayPort cable.

???Select the audio input terminal to be used in DisplayPort of AUDIO SELECT on the SETUP menu.

When DisplayPort is selected, connection to the audio input terminal is unnecessary.

2. DVI-I input terminal

???Use a commercially available signal cable (DVI-I 29 pin).

???Select the audio input terminal to be used in DVI-I of

AUDIO SELECT on the SETUP menu.

???If the display is not shown properly, set EDID SELECT

(DVI-I) of INPUT SELECT on the SETUP menu according to the device to be connected.

3.PC/AV HDMI1 input terminal

4.PC/AV HDMI2 input terminal

???Use a commercially available HDMI cable (conforming to the HDMI standard).

???Set HDMI1 or HDMI2 of INPUT SELECT on the SETUP menu according to the device to be connected.

???Select the audio input terminal to be used in HDMI1[AV], HDMI1[PC], HDMI2[AV] or HDMI2[PC] of AUDIO SELECT on the SETUP menu.

When HDMI is selected, connection to the audio input terminal is unnecessary.

5. PC/AV D-sub input terminal

???Set D-SUB of INPUT SELECT on the SETUP menu according to the device to be connected.

???To use with D-SUB[VIDEO], connect the green terminal to the device???s video output.

???Select the audio input terminal to be used in D-SUB[RGB],

D-SUB[COMPONENT] or D-SUB[VIDEO] of AUDIO SELECT on the SETUP menu.

6.Audio1 input terminal

7.Audio2 input terminal

???Use an audio cable without resistance.

???Set the audio input terminal to be used in each input mode in AUDIO SELECT on the SETUP menu.

Caution

??? Use only the power cord supplied with the monitor.

1.Turn off the main power switch.

2.Plug the power cord (supplied) into the AC input terminal.

3.Plug the power cord (supplied) into the AC power outlet.

3 For power outlet

Main power switch

1 2

Power cord (Supplied)

TIPS

AC input terminal

Installing the batteries

1.Press the cover gently and slide it in the direction of the arrow.

2.See the instructions in the compartment and put in the supplied batteries (R-6 (???AA??? size) x 2) with their plus (+) and minus (-) sides oriented correctly.

3.Close the cover.

TIPS

???When the batteries become exhausted, replace them with new (commercially available) batteries.

???The supplied batteries (R-6 (???AA??? size) x 2) may become exhausted quickly depending on how they are stored.

???If you will not be using the remote control for a long time, remove the batteries.

???Use manganese or alkaline batteries only.

Remote control operation range

The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10?? from the center to the top/ bottom/right/left of the remote control sensor.

Remote control sensor

Caution

???Turn on the monitor first before turning on the PC or playback device.

Turning on the main power

Main power switch

Caution

???The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on.

???When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds.

???For a complete electrical disconnection, pull out the main plug.

Turning power on/off

Press the POWER button or POWER switch to turn the power ON/OFF.

Caution

???When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction.

TIPS

???When the main power switch is off, the monitor cannot be turned on.

???If the monitor is in the input signal standby mode and you press the POWER button on the remote control unit, the monitor enters standby mode.

???Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.

???To disable the logo screen from displaying when turning the power ON, set LOGO SCREEN to OFF on the OTHERS menu. (See page 28.)

nDate/time setting

???If the time has yet to be set when the monitor is first turned on, the date/time setting screen appears. Set the date and time.

DATE/TIME SETTING

OK??????[ENTER] CANCEL??????[RETURN]

1.Press or to select the date and time, and press or to change the numerical values.

2.Press ENTER .

???Be sure to set the date and time.

???The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the SETUP menu when the date/time setting screen disappears.

TIPS

???Set the date in ???Month/Day/Year??? order.

???Set the time on a 12-hour basis.

???The clock is maintained by the internal battery.

???If you already set the time but the date/time setting screen appears when the power is turned on, the internal battery may be exhausted. Please contact an authorized Sharp servicing dealer or service center for assistance with battery replacement.

???Estimated service life of the internal battery: About 5 years (depending on monitor operation)

???The initial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its expected operation life.

Turning Power On/Off

Disabling power on/off operations

Power on/power off operations can be disabled in order to protect the monitor from an accidental power off. Set the ADJUSTMENT LOCK in FUNCTION menu to ???ON 2???. (See page 32.)

2

5

1

3

4

4. VOL +/- (Volume adjustment)

Pressing or displays the VOLUME menu when the menu screen is not displayed.

Press or to adjust the volume of the sound.

*If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears.

6 7

9 8

10

1. INPUT (Input mode selection)

The menu is displayed. Press or to select the input mode, and press ENTER to enter.

*You can select the input terminal by pressing the input switch of the monitor.

*1 Select the terminal to be used in HDMI1 of INPUT

SELECT. (See page 24.)

*2 Select the terminal to be used in HDMI2 of INPUT SELECT. (See page 24.)

*3 Select the terminal to be used in D-SUB of INPUT SELECT. (See page 24.)

*4 Select the terminal for AUDIO SELECT which is used for audio input. (See page 24.)

2. MUTE

Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the previous level.

3. MENU

Displays and turns off the menu screen. (see page 20.)

5. BRIGHT +/- (Brightness adjustment)

Press or to adjust the brightness.

*If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears.

6.ENTER

Confirms the setting.

7.RETURN

Returns to the previous screen.

8. SIZE (Screen size selection)

The menu is displayed.

Press or to select the screen size. (See page 19.)

9. DISPLAY

Displays monitor information.

The display changes from INFORMATION1 ??? INFORMATION2 ??? clear display, and so on every time you

press this button.

???The display disappears automatically after about 15 seconds.

???LAN is displayed during LAN communication.

???If LAN is displayed in red, there is a duplicate IP address.

10. MODE (Color mode selection)

Each time you press this button, the color mode changes in the following order:

STD (Standard) ??? VIVID ??? sRGB ???

HIGH ILLUMINANCE ??? STD...

???HIGH ILLUMINANCE is a display with colors suited to bright locations.

???sRGB applies to PC input only.

sRGB is international standard of color representation specified by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crystal???s characteristics and represents color tone close to its original image.

Displaying the menu screen

Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 20 to 29 for details of each menu items.

Caution

???Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings.

nExample of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Press MENU to display the menu screen.

2.Press or to select PICTURE, and press ENTER.

3.Press or to select CONTRAST.

4. Press or to adjust the setting.

For items that have , press ENTER, make settings and then press RETURN.

5. Press MENU to close the menu screen.

TIPS

???The menu will differ depending on the input mode.

???The menu screen will close automatically if no operation is performed for about 15 seconds. (DATE/TIME SETTING, SCHEDULE and LAN SETUP screens will close in about 4 minutes.)

nMenu screen display

1 Name of the menu

2Input mode

3An item being selected (highlighted)

4Screen resolution of input signal, and other data.

TIPS

???Items that cannot be selected appear in gray.

(e.g. Function not supported by the current input signal)

nDual screen display

You can display two screens simultaneously.

Set this function with PIP MODES of PIP/PbyP in the MULTI/

PIP menu.

*The currently selected input signal is displayed on the main screen.

*The following combinations are available for display: DisplayPort - HDMI1 or HDMI2

DisplayPort - D-SUB[RGB] DisplayPort - D-SUB[COMPONENT] DisplayPort - D-SUB[VIDEO]

DVI-I - HDMI1 or HDMI2

DVI-I - D-SUB[COMPONENT] DVI-I - D-SUB[VIDEO]

TIPS

???You might infringe on a copyright of the author which is protected by copyright law when you display the images of the computer screen and television/VCR simultaneously for profit-making or to show the image to the public.

???The screen size for dual-screen display is the same as the screen size for single-screen display. The Dot by Dot screen is displayed in NORMAL size except when it is set as the PIP main screen.

???When dual-screen display is selected, the SCREEN

MOTION function is disabled.

???When dual-screen display is selected, the AUTO INPUT

CHANGE function is disabled.

???When dual-screen display is selected, the screen cannot be enlarged.

???When dual-screen display is selected, the INPUT SELECT options cannot be set.

???When an interlaced signal (1080i, 480i, video) is input to the sub screen, horizontal lines may flicker. If this happens, display the image on the main screen.

Menu Items

nEnlarge

???You can align several monitors and integrate them into a single large screen to display.

???Up to 5 monitors can be aligned in both the horizontal and vertical directions.

???Each monitor displays enlarged views of separated images.

(Example)

Horizontal direction: 2 monitors

Vertical direction: 2 monitors

Horizontal direction: 3 monitors

Vertical direction: 2 monitors

Setting procedure

Set using MULTI in the MULTI/PIP menu.

1.Set ENLARGE to ON.

2.Select ADVANCED (ENLARGE).

3.Set the number of monitors aligned in the horizontal direction in ENLARGE H.

4.Set the number of monitors aligned in the vertical direction in ENLARGE V.

5.Set the section of the separated image to be displayed on each monitor in ENLARGE-POS.

1)Press ENTER.

2)Press , , or to select position, then press MENU.

TIPS

???When Enlarge is used, the SCREEN MOTION function is disabled.

???When Enlarge is used, the AUTO INPUT CHANGE function is disabled.

???When Enlarge is used, the HDMI AUTO VIEW function is disabled.

nZOOM2 SPECIAL SETTING

If you connect a laptop computer with any of the following screen resolutions and black bands appear around the screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the OTHERS menu to ON and then select ZOOM2 in the SIZE setting.

This displays the area inside the black band.

*1: This setting is effective only when the screen resolution, including the black band, is one of the resolutions listed above.

*2: Use the automatic screen adjustment.

Menu Items

nSCHEDULE

You can set the time to switch the monitor on and off.

Set this function with SCHEDULE in the SETUP menu. (See page 24.)

1.Press or to select the SCHEDULE number, and press .

2.Set the SCHEDULE. (See the description below.)

Press or to select items, and press or to change the setting.

3.Press ENTER.

SCHEDULE becomes effective.

(1)

???: SCHEDULE effective

-: SCHEDULE not effective

(2) POWER

ON : Switches the monitor on at the specified time.

OFF : Switches the monitor off at the specified time and puts the monitor in standby mode.

(3) DAY OF THE WEEK

Specifies the day of the week to execute the SCHEDULE. 0:ONLY ONCE

Executes the SCHEDULE once on the specified day. Specify the day of the week to execute the SCHEDULE.

1:EVERY WEEK

Executes the SCHEDULE on the specified day of the week every week. Specify the day of the week to execute the

SCHEDULE.

Periodic setting such as ???Monday through Friday??? is also possible.

2:EVERY DAY

Executes the SCHEDULE every day regardless of the day of the week.

(4) TIME

Specifies the time to execute the SCHEDULE. Set the time on a 12-hour basis. (Factory default)

Can be entered as 24-hour time using the TIME setting in

DATE/TIME FORMAT.

(5) INPUT

Specifies the input mode at power-on. If you don???t specify this the input active at the last power-off will appear. Input modes displayed on HDMI1, HDMI2 and D-SUB will depend upon the INPUT SELECT settings.

(6) BRIGHT

Sets the brightness when changing the screen brightness at a specified time.

Caution

???Do not switch off the main power after setting the

SCHEDULE.

???Specify the correct date and time. (See page 24.)

SCHEDULE does not function unless the date and time are specified.

???Check regularly that the set date and time are correct.

???When STANDBY MODE is LOW POWER, SCHEDULE cannot be set.

???When a temperature abnormality occurs and the backlight brightness is reduced, the brightness is not changed even if a schedule set to BRIGHT is executed.

TIPS

???Up to 8 SCHEDULE items can be registered.

???Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.

???A SCHEDULE that has a large number has precedence over that of a small number when schedules overlap.

You can return the settings to their factory-preset values and restrict operations.

1.Hold SIZE down until ???F??? appears in the upper left corner of the screen.

2.While ???F??? appears, press , , , in that order.

FUNCTION

OK???[ENTER] END???[RETURN]

3.Select and set the items.

ALL RESET

Resets the settings to the factory default settings.

Press ENTER , select the resetting method, and then press

ENTER.

After initialization, turn the main power switch off and then back on.

ALL RESET1.....Resets all the settings to the factory default settings.

ALL RESET2.....Returns all settings to the factory default settings except for the following items: LAN SETUP, RS-232C/LAN SELECT,

ID No. SET, BAUD RATE, NETWORK,

MAIL, SERVICE & SUPPORT, and

SNMP (See page 25, and pages 49 to 52.)

ADJUSTMENT LOCK

You can disable operations on the monitor and the remote control unit that use buttons.

OFF....Enables operation.

ON 1...Disables all operations other than turning power on/off and FUNCTION.

ON 2...Only the FUNCTION operation is enabled.

Disables all operations other than FUNCTION (not even power on/off).

ADJUSTMENT LOCK TARGET

Sets the target to prohibit operation of with

ADJUSTMENT LOCK.

REMOTE CONTROL..... Prohibits remote control operation

MONITOR BUTTONS.... Prohibits monitor switch operation

BOTH............................. Prohibits remote control and monitor switch operation

RS-232C/LAN

Specifies whether to allow control via RS-232C or LAN (see pages 33 and 45).

OSD DISPLAY

Shows/hides the menu, modes and messages.

The FUNCTION screen cannot be hidden.

LED

Specifies whether to light the power LED.

TEMPERATURE ALERT

Selects the notification method for an abnormal

Selects the notification method for a hardware error. OFF............... Do not notify about the error.

OSD & LED... When a hardware error is detected, the

POWER BUTTON

Normally, leave this setting as MONITOR.

When using an optional part, if instruction appears, change the setting accordingly.

CONTROLLER INPUT

Normally, you do not need to change this setting.

When using an optional part, if instruction appears, change the setting accordingly.

4. Press RETURN to return to the normal screen.

TIPS

???When both abnormal temperature and hardware error are detected, the hardware error notification overrides.

???If TEMPERATURE ALERT or STATUS ALERT is set to OSD&LED, alert messages will appear even if the OSD

DISPLAY is set to ON 2 or OFF.

???If TEMPERATURE ALERT or STATUS ALERT is set to LED or OSD & LED, the LED lights even if the LED function is set to OFF.

You can control this monitor from a PC via RS-232C (COM port) on the PC.

You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 34), you can make input mode selection/adjustment or can check the status of a specific monitor.

TIPS

???To control the monitor via RS-232C, set RS-232C/LAN

SELECT to RS-232C.

???You cannot use RS-232C and LAN control simultaneously.

PC connection

nOne-to-one connection with a PC

Connect with RS-232 straight cable between the PC???s COM

port (RS-232C connector) and the RS-232C input terminal on the monitor.

RS-232C input terminal

PC

To COM port

RS-232 straight cable

(commercially available)

nDaisy chain connection??? Advanced operation

Connect with RS-232 straight cable between the PC???s COM

port (RS-232C connector) and the RS-232C input terminal on the first monitor.

Next, connect RS-232 straight cable to the first monitor???s

RS???232C output terminal and to the second monitor???s

RS-232C input terminal. Connect in the same way to the third and subsequent monitors.

Up to 25 monitors can be connected. (Depending on the length of the cable used and the surrounding environment.)

Second monitor

Communication conditions

Set the RS-232C communication settings on the PC to match the monitor???s communication settings as follows:

*Set to the same baud rate as the BAUD RATE setting of

SETUP menu. (Initial setting: 38400 bps)

*When connecting multiple monitors in a daisy chain, set all monitors to the same BAUD RATE.

Communication procedure

nCommand format

When a command is sent from the PC to the monitor, the monitor operates according to the received command and sends a response message to the PC.

Example: VOLM0030

VOLM 30

*Be sure to input 4 characters for the parameter. Pad with spaces (??? ???) if necessary.

(??? ??? is a return code (0DH, 0AH or 0DH)) Wrong : VOLM30

When inputting a negative value, specify a numerical value in three digits.

Example: AUTR-005

Do not use spaces for MPOS, DATE, and SC01 through SC08. Specify parameters using a specified number of characters.

Example: MPOS010097

If a command has ???R??? listed for ???DIRECTION??? in the ???RS-232C command table??? on page 37, the current value can be returned by using ??????? as the parameter.

Example:

*If an ID number (see page 34) has been assigned

(For example, ID number = 1).

nResponse code format

When a command has been executed correctly

A response is returned after a command is executed. * If an ID number has been assigned

ID number of responding monitor

nCommunication interval

???After OK or ERR is returned, you must send the following commands.

To set a timeout for the command response, specify 10 seconds or longer.

When connecting multiple monitors in a daisy chain, set the timeout to at least the product of the monitor???s position from the computer multiplied by 10 seconds.

Example) 3rd monitor from computer: 30 seconds or longer.

???Provide an interval of 100 ms or more between the command response and the transmission of the next command.

VOLM0020

When a command has not been executed

* If an ID number has been assigned

ID number

TIPS

??????ERR??? is returned when there is no relevant command or when the command cannot be used in the current state of the monitor.

???If communication has not been established for reasons such as a bad connection between the PC and monitor, nothing is returned (not even ERR).

??????ERR??? may be returned when a command cannot be received correctly due to interference from the surrounding environment.

Please ensure that the system or software retries the command if this occurs.

???If no monitor has been assigned the designated ID number

(e.g. if the command IDSL0002 is used, but no monitor with ID number: 2 is found), no response is returned.

If execution of the command is taking some time

When the following commands are used, ???WAIT??? is returned. In this case, a value will be returned if you wait a while. Do not send any command during this period.

No ID number is attached to WAIT response.

???Commands which return WAIT:

1.When repeater control is used

2.When an IDSL or IDLK command is used

3.When one of the following commands is used: RSET,

INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR, AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,

ESHV, ENLG

When control via RS-232C is locked (to prevent use) using the operation lock function (see page 33)

When RS-232C/LAN SELECT is set to LAN

OK

Interval of 100 ms or more

INPS0001

WAIT

OK

TIPS

???When executing ALL RESET, set the timeout period to 30 seconds or longer.

???When turning the power on while the POWER ON DELAY function is in use, set the timeout period to the POWER ON

DELAY period + 10 seconds or longer.

Advanced operation

This section explains commands for daisy chain connection.

The basic communication procedure is the same as in the

???One-to-one connection with a PC??? section.

nID numbers

You can assign a unique ID number to each monitor (see page 25). This allows you to control a particular monitor in a daisy chain of monitors.

You can assign ID numbers either from the menu screen or from the PC using RS-232 cable.

[Example]

ID number: 1 ID number: 2 ID number: 3 ID number: 4

If monitors are connected as shown above, you can execute commands like ???Set the volume of the monitor with ID 4 to 20???.

When designating ID numbers for a set of monitors linked in a daisy chain, you should basically avoid any duplication of ID numbers.

ID numbers do not have to be assigned in ascending order starting from the PC. They can also be connected as shown below.

[Example]

ID number: 3 ID number: 2 ID number: 4 ID number: 1

nCommands for ID control

The command examples shown on this page assume the following connection and ID number set up.

ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST..........A monitor receiving this command sets its own ID number in the parameter field.

Example:

IDST0001

OK 001 ??? The ID number of this monitor is set to 1.

IDLK.........The parameter of this command sets the ID

number of the monitor. The monitor is subject to all subsequent commands.

Example:

TIPS

You can automatically assign ID numbers by using the IDST command with the Repeater control (see ???Repeater control??? on page 36).

For example, using the command ???IDST001+??? automatically sets the ID numbers, as shown below.

[Example]

ID number: 1 ID number: 2 ID number: 3 ID number: 4

VOLM0020 ???

WAIT

OK 002 IDLK0000 ???

WAIT ???

OK 002 ??? VOLM0010

OK 001 ???

Sets volume of monitor with ID number: 2 to 20.*

Canceling fixed ID number setting

Canceling IDLK

Cancelation complete

The volume of the monitor with ID number: 1 (the one directly connected to the PC) is set to 10. (IDLK is canceled.)

IDSL.........The parameter of this command sets the ID number

of the monitor. The monitor is subject to the next command.

Example:

to the PC) is set to 20.*

*The IDSL command is effective only once, for the immediately succeeding command.

*The IDLK command remains effective until it is canceled, or power is shut off.

IDCK........Provides screen display of the ID number currently assigned to a monitor, and the ID number currently set for IDLK (if any).

Example:

(After executing IDLK0002)

nRepeater control

This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command.

This function is called repeater control. You can use Repeater control function without assigning ID numbers.

[Example]

Setting of the GAMMA user data

nTo transfer the GAMMA user data

Use the user data transfer commands (UGRW, UGGW and UGBW). For each of the R, G and B colors, divide the total

512 pieces of user data into 16 blocks, and transfer 32 pieces of data with each command.

C1 C2 C3 C4 P1 P2 P3 P4 ??? S1 S2

Command field Block number (01 to 16) Data field Checksum field

*If monitors are connected as shown above, you can execute a command like ???Set all monitors??? input settings to

D-SUB[RGB]???.

nRepeater control command

Repeater control is achieved by setting the FOURTH CHARACTER of the parameter to ???+???.

Example:

VOLM030 + ??? Sets volume of all monitors to 30.

In repeater control, responses are returned by all the connected monitors.

If you want to determine that a value has been returned by a specific set, assign ID numbers to each monitor in advance.

When some monitors do not return their responses, the probable cause is that the monitors could not receive the command or command processing is not complete. Do not send a new command.

Example: (When 4 monitors are connected, and assigned ID numbers: 1 through 4)

VOLM030 +

WAIT

OK 001

OK 002

OK 003

OK 004 ??? If 4 monitors are connected in

a chain, reliable operation can be ensured by sending a new command only after a reply has been returned by 4th (last) monitor.

Repeater control can also be used for reading settings.

Example:

VOLM ? ? ? +

TIPS

???If repeater control is used during ID designation (IDSL,

IDLK), the ID designation is canceled.

Example: To transfer the data of block 1 (0 to 31 levels)

of red (R) data

UGRW01000000010002 ??? 0031C0

One piece of data consists of 4 digits.

Command Block number 32 pieces of data Checksum

*If data is less than 4 digits, add a ???0??? (zero) to make it 4 digits.

*The checksum field is the character string (ASCII) data of lower-order one byte which indicates the sum of the block number and 32 pieces of data in hexadecimal (0 to F).

nSaving the GAMMA user data

Use the user data save command (UGSV) to save the transferred user data in the monitor.

If the data is not saved, it will be cleared when:

???The main power switch is off

???STANDBY MODE is LOW POWER and the monitor enters standby mode

nActivating the GAMMA user data

To activate the transferred user data, select USER for GAMMA of the PICTURE menu, or send the corresponding RS-232C command.

nChecking the GAMMA user data

Use the user data read commands (UGRR, UGGR and

UGBR) to return 512 pieces of user data for each of the R, G and B colors. Divide the data into 16 blocks and return 32 pieces of data with each command. The value to be returned is not the value stored in the monitor, but the value in the temporary memory for display. (These values are the same when the user data save command (UGSV) above has been sent.)

TIPS

???The user data is not initialized by RESET of the PICTURE menu. To initialize the user data, use ALL RESET of the

FUNCTION menu.

The GAMMA user data initialize command (UGRS) allows the initialization of the user data only.

Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN.

You can also configure the monitor to send e-mail notification when it has a problem.

The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

Network (LAN)

Hub

LAN terminal

LAN cable (commercially available, straight)

TIPS

???You must assign an IP address to the monitor by following the procedures in ???Settings to connect to a LAN???. (See the description on the right.)

???Your PC must be installed with Internet Explorer (version 7.0 or later).

???To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 25.)

???You cannot use RS-232C and LAN control simultaneously.

Initializing personal information

???Personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET 1. (See page 32.) Note that ALL RESET 2 will not initialize e-mail addresses and other settings.

Settings to connect to a LAN

Set the monitor???s IP address and subnet mask to match the settings of your LAN.

These settings can be made on either the monitor or a PC connected to the monitor.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

??? To set on the monitor

Set RS-232C/LAN SELECT of COMMUNICATION SETTING on the SETUP menu to LAN, and then set the LAN SETUP options. (See page 25.)

After setting each item, select SET and press ENTER.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON.

To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

Press or to select items, and press or to change the values.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

Press or to select items, and press or to change the values.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway.

If you are not using a gateway, specify ???0.0.0.0???.

Press or to select items, and press or to change the values.

RESET

Resets the values of the LAN settings to the factory preset values.

Select ON and then press ENTER.

TIPS

???When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

Controlling the Monitor with a PC (LAN)

??? To set from a PC

When the monitor is connected to a PC, LAN settings can be configured via PC.

Set up process

(1)Connect your monitor to a PC

(2)Specify the PC???s IP address

(3)Configure the monitor???s LAN settings

(1) Connecting your monitor to a PC

Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor.

LAN cable

(commercially available, crossover)

(2) Specifying the PC???s IP address

To configure the monitor???s LAN settings, you must temporarily change the settings on the PC.

This explanation is based on Windows 7.

1.Log on to the PC with an administrator account.

2.Click [Start], and then click ???Control Panel???.

3.Click ???View network status and tasks??? in ???Network and

Internet???.

In ???Classic View???, click ???Network and Sharing Center???.

4.Click ???Local Area Connection??? and then ???Properties???.

5.Click ???Internet Protocol Version 4 (TCP/IPv4)??? and then

???Properties???.

6.Make a note of the current IP address, subnet mask, and default gateway settings.

Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

7.Temporarily change the IP address and subnet mask.

To access the monitor as it is shipped from the factory, set as follows.

???IP Address: 192.168.150.1

???Subnet Mask: 255.255.255.0

???Default Gateway: (leave blank)

8. Click [OK] and then reboot the PC.

TIPS

??? This monitor is factory preset as shown below.

(When DHCP CLIENT is set to OFF)

(3) Configuring the monitor???s LAN settings

Access the monitor using Internet Explorer.

Controlling the monitor

1.Turn the power ON to the monitor.

2.Set RS-232C/LAN SELECT of COMMUNICATION

SETTING on the SETUP menu to LAN.

3.Set DHCP CLIENT of LAN SETUP of COMMUNICATION SETTING on the SETUP menu to OFF.

PC operation

4.Launch Internet Explorer, in the ???Address??? box type ???http://192.168.150.2/??? and press the Enter key.

5. Click on ???LAN SETUP??? under NETWORK.

6. Specify the ???DHCP CLIENT???, ???IP ADDRESS???,etc.

Controlling the Monitor with a PC (LAN)

Controlling with a PC

??? Basic operation

You use Internet Explorer on a PC on the LAN to control the monitor.

1.Launch Internet Explorer on the PC.

2.In the ???Address??? box, type ???http://??? followed by your monitor???s IP address followed by ???/???, then press the Enter key.

You can confirm the IP address with the DISPLAY function.

When prompted to enter a user name and password, type the user name and password that you specified in the security settings (see page 49), and click [OK].

3.You can check, control, and change the monitor???s status and settings by clicking the menu items on the left side of the screen.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ???ON???.

To set the address manually, set this to ???OFF???.

IP ADDRESS

If the DHCP CLIENT is set to ???OFF???, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to ???OFF???, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to ???OFF???, specify the default gateway. If you are not using a default gateway, specify ???0.0.0.0???.

7.When the setting is changed, click [Apply].

8.Check the message and click [OK].

9.Exit Internet Explorer.

10.Restore the PC???s IP address jotted in Step 6, ???(2)

Specifying the PC???s IP address???.

11. Connect the monitor and the PC to the LAN.

Caution

???Wait 10 seconds after clicking [OK] before proceeding.

???When operating using the remote control unit or similar, click [Refresh].

TIPS

???When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

???If you see an [Apply] button next to a setting, click it after you change that setting.

TIPS

???See pages 48 to 52 for details on each setting.

???If you click [Refresh] before the screen finishes updating the current display, the ???Server Busy Error??? will appear. Wait for a moment before operating your monitor again.

???You cannot operate the monitor while it is warming up.

???If ???DHCP CLIENT??? is set to ???ON???, press DISPLAY on the remote control unit two times and then check the monitor???s

IP address.

??? INFORMATION

Information about this monitor appears.

??? CONTROL

You can control the operations corresponding to the buttons (POWER INPUT SIZE ) on the remote control unit. (See page 18.)

TIPS

??? In standby mode, Power ON is the operation available.

??? ADJUSTMENT

You can adjust these settings which are also available on the monitor???s menu.

???SCREEN (See page 21.)

???PICTURE (See page 22.)

???PICTURE (ADVANCED) (See page 23.)

???AUDIO (See page 24.)

???SETUP (See page 24.)

???MONITOR (See page 26.)

???OTHERS (See page 28.)

???SCHEDULE (See page 30.)

???MULTI (See page 27.)

???PIP/PbyP (See page 27.)

???FUNCTION (See page 32.)

TIPS

???After changing DISPLAY COLOR PATTERN to OFF, click [Refresh] to correctly retrieve the status of the monitor.

??? NETWORK (LAN SETUP)

This screen allows you to set the settings necessary when the monitor is connected to a LAN.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON.

To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway.

If you are not using a default gateway, specify ???0.0.0.0???.

DNS SERVER ADDRESS AUTO ACQUISITION

If the DHCP CLIENT is set to ON, specify whether or not to automatically obtain the DNS server address.

DNS SERVER

Specify the DNS server address if the DHCP CLIENT is SET to OFF or the DNS SERVER ADDRESS AUTO ACQUISITION is set to OFF.

If you are not using a DNS server, specify ???0.0.0.0???.

RESET

Clicking [Execute] returns all of the LAN SETUP settings to the factory-preset values except for the DNS SERVER

ADDRESS AUTO ACQUISITION and DNS SERVER settings.

TIPS

???When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

Controlling the Monitor with a PC (LAN)

??? NETWORK (SECURITY)

This screen allows you to specify the security-related settings.

USER NAME / PASSWORD

Sets up a user name and password to restrict access to this monitor.

After entering a user name and password, click [Apply].

ACCEPT IP ADDRESS

You can limit access to this monitor by registering IP addresses of PCs that should have access.

To limit access, specify the option ???From only specific IP addresses???. Otherwise, to allow access from any PC, specify

???All IP Addresses???.

IP ADDRESS 1 to 3

If ???ACCEPT IP ADDRESS??? is set to ???From only specific IP addresses???, enter the IP addresses that you want to allow.

TIPS

???The USER NAME and PASSWORD can be up to 8 alphanumeric characters (hyphens and underscores allowed).

???To cancel the user name and/or password after it has been set, make the box empty and click [Apply].

Controlling the Monitor with a PC (LAN)

??? NETWORK (GENERAL)

This screen allows you to specify the general LAN settings.

MONITOR NAME

Specify a name for this monitor as it should appear on the

Internet Explorer screen.

AUTO LOGOUT TIME

Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network.

Specify in minutes from 1 to 65535. A value of ???0??? will disable this function.

DATA PORT

Specify the TCP port number to use for exchanging data with the monitor.

Specify a value from 1025 to 65535.

SEARCH PORT

Specify the port number to use when searching for this monitor.

Specify a value from 1025 to 65535.

INSTALLATION INFORMATION (NAME/LOCATION)

Specify the information to display for this monitor in the Internet Explorer window.

LINK MODE

Selects the link speed and duplex.

Use AUTO normally.

TIPS

???The MONITOR NAME can be up to 16 alphanumeric characters or symbols.

???Enter up to 50 characters in the NAME field in the

INSTALLATION INFORMATION.

???Enter up to 100 characters in the LOCATION field in the

INSTALLATION INFORMATION.

??? MAIL (ORIGINATOR)

This screen allows you to configure the e-mail sent periodically or when the monitor has an error.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

SMTP SERVER

Specify the SMTP server address for sending e-mail.

*When using a domain name, make sure to specify the DNS server as well. (See page 49.)

SMTP PORT

If the ???AUTHENTICATION??? is ???SMTP-AUTH???, specify the port number.

ORIGINATOR E-MAIL ADDRESS

Specify the e-mail address for this monitor.

This address becomes the e-mail address of the originator.

ORIGINATOR NAME

Specify the name for the originator.

This name appears in the ???Originator Name??? field of the e-mail.

AUTHENTICATION

Specify the authentication method to use when sending e-mail.

POP SERVER

If the ???AUTHENTICATION??? is ???POP before SMTP???, specify the POP server address.

ACCOUNT NAME / PASSWORD

If the ???AUTHENTICATION??? is ???POP before SMTP??? or

???SMTP-AUTH???, specify the account name and password to connect to the SMTP server.

TIPS

???You can enter up to 64 alphanumeric characters or symbols for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR NAME, ACCOUNT NAME, and PASSWORD.

???The SMTP SERVER and POP SERVER can be up to 64 characters.

The following characters can be used: a-z, A-Z, 0-9, - , .

??? MAIL (RECIPIENT)

This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error.

RECIPIENT E-MAIL ADDRESSES

Specify the e-mail addresses to send error notification e-mail to.

CONDITION

Specify the conditions to send mails.

When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting.

CONFIRMATION

Sends test e-mail.

This allows you to confirm that the e-mail settings are configured properly.

Attach the log file to a TEMPERATURE/HARDWARE error e-mail.

When this option is checked, a log is added to the mail which notifies a temperature or status error.

TIPS

???The RECIPIENT E-MAIL ADDRESSES can be up to 64 alphanumeric characters or symbols.

Controlling the Monitor with a PC (LAN)

??? MAIL (PERIODICAL)

When PERIODICAL for CONDITION of MAIL (RECIPIENT) is checked, set the date and time to send the mail.

DAY OF THE WEEK

Specify the day of the week to send the periodical mails.

TIME

Specify the time of the day to send the periodical mails.

Caution

???Do not turn off the main power when you set to send the periodical mails.

???Specify the correct date and time. (See page 24.)

If the date and time settings are incorrect, the periodical mail is not sent properly.

???Regularly confirm that the specified date and time is correct.

???When LOW POWER is selected for STANDBY MODE, periodical mails will not be sent in standby mode.

Controlling the Monitor with a PC (LAN)

??? SNMP

You can configure settings related to SNMP.

SNMP SETTING

Set whether to enable or disable SNMP.

VERSION

Set the version of the SNMP to be supported.

COMMUNITY NAME 1 to 3

Set the name of the community required for the access.

USER 1 to 3

Set the user name, password, authentication method and other options required for access.

TRAP SETTING

Set whether to enable or disable the trap function.

When this function is enabled, a trap will be sent when the monitor is turned on.

TRAP SETTING OF AUTHENTICATION ERROR

Set whether the trap function sends a notification when authentication fails.

TRAP ADDRESS & PORT

Set the destination address and port number of the notification sent by the trap function.

Caution

???After you set SNMP, click [Switch the main power of monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation.

???If the IP address is changed while the SNMP function is operational, turn off the monitor and then turn it on again with the main power switch.

TIPS

???Depending on the SNMP settings, a short delay may occur before the SNMP is usable. (About 5 minutes)

???Up to 16 alphanumeric letters and symbols can be used for the community name, user name and password.

??? SERVICE & SUPPORT

(URL INFORMATION)

You can display a specific URL in the URL INFORMATION field on the INFORMATION screen when an error occurs in the monitor. (See page 48.)

URL INFORMATION

Enter the URL to display on the INFORMATION screen when an error occurs on the monitor.

Up to 64 alphanumeric characters or symbols can be used.

CONDITION

Specify the condition to display the URL.

CONFIRMATION

The home page of the specified URL is displayed.

You can check whether the URL you entered is correct.

TIPS

???It is also possible to specify the message text, such as the name of a contact or a telephone number, to be displayed instead of the linked URL.

If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips.

There is no picture or sound.

???Is the power cord disconnected? (See page 13.)

???Is the main power switch off? (See page 16.)

???Is the monitor in standby mode (the power LED illuminating in orange)? (See page 16.)

???Make sure correct input mode is selected. (See page 18.)

???If any external equipment is connected, make sure the equipment is operating (playing back).

Remote control does not work.

???Are the batteries inserted with polarity (+,-) aligned? (See page 15.)

???Are the batteries exhausted?

???Point the remote control unit toward the monitor???s remote control sensor. (See page 15.)

???Is the menu display hidden or is operation disabled? (See page 32.)

Sound from left and right speakers is reversed. Sound is heard from only one side.

???Are audio cables connected properly?

???Check the setting of BALANCE for AUDIO menu. (See page 24.)

There is a picture but no sound.

???Is the sound muted?

???Make sure the volume is not set to minimum.

???Are audio cables connected properly?

???Is the setting of AUDIO SELECT on the SETUP menu correct? (See page 24.)

Unstable video.

???The signal may be incompatible.

???Try the automatic screen adjustment when the

D-SUB[RGB] or DVI-I (analog) are used.

The video from the PC/AV HDMI input terminal does not appear properly.

???Is the setting for HDMI1 or HDMI2 of INPUT SELECT on the SETUP menu correct? (See page 24.)

???Is the HDMI cable HDMI standard compliant? The monitor will not work with cables that are not standard compliant.

???Is the input signal compatible with this monitor? (See page 58.)

The video from the DVI-I input terminal does not appear properly.

???Is the setting for EDID SELECT (DVI-I) of INPUT SELECT on the SETUP menu correct? (See page 24.)

???Is the input signal compatible with this monitor? (See page 58.)

???Turn off the power to the connected equipment and then turn the power on again.

???If the monitors are connected in a daisy chain, turn off the power to all the monitors connected in a daisy chain and then turn the power on again.

The video from PC/AV D-Sub input terminal does not appear correctly.

???Is the setting for D-SUB of INPUT SELECT on the SETUP menu correct? (See page 24.)

???Is the input signal compatible with this monitor? (See page 58.)

The video from the DisplayPort does not appear properly.

???Is the input signal compatible with this monitor? (See page 58.)

Control buttons do not work.

There is no picture.

???Load noises from outside may be interfering with normal operation. Turn off the power and turn it on after waiting at least 5 seconds, and then check the operation.

The input mode changes automatically.

???When the AUTO INPUT CHANGE is ON and no signal is present in a selected input mode, the AUTO INPUT

CHANGE automatically changes the selected mode to a mode where a video signal is present.

The input mode may change in the following cases:

-When a computer is in standby mode.

-When video play is stopped with a playback device.

Power LED flashes red.

???STATUS [xxxx]??? appears in the corner of the screen.

???Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer.

(When STATUS ALERT is set to OSD & LED. This varies depending on the setting.)

When ???AUTO DIMMING??? is displayed.

???When the internal temperature of the monitor rises excessively, the brightness of the backlight automatically decreases in order to prevent a further temperature rise. If

you attempt to use to adjust the brightness while the monitor is in this state, ???AUTO DIMMING??? is displayed and you cannot change the brightness.

???Remove the cause of the excessive temperature rise.

The monitor makes a cracking sound.

???You may occasionally hear a cracking sound from the monitor. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the monitor???s performance.

nPC/AV D-sub input terminal pins

(Mini D-sub 15 pin)

nRS-232C input terminal pins

(D-sub 9 pin)

5GND

5GND

Cover screws (supplied)

Cover (supplied)

Screw masking sheets (supplied)