Sharp_Air_Conditioner

)DQ )DQ

6ORZHU)DVWHU

212))

AF-Q100RX

AF-Q120RX

10 10 11 11

15 15

.... 16

TO EXHAUST AIR FROM THE ROOM 16

......... 17

PRECAUTIONS................................... 19

AF-Q100RX,AF-Q120RX

:LQGRZVDVKVHDO

WKLQDGKHVLYHEDFNHG )RDPWRS

ZLQGRZJDVNHW

/HIW

DFFRUGLRQ

SDQHO

212))

7RSPRXQWLQJUDLO

VHDOVWULS

6LOOVXSSRUW

1XW %ROW

7RSPRXQWLQJUDLO

5LJKW

DFFRUGLRQ

SDQHO

:LQGRZORFNLQJ 7\SH$ 7\SH% 7\SH& 7\SH' EUDFNHW

WINDOW REQUIREMENTS

???These instructions are for a standard double-hung window. You will need to modify them for other types of windows.

CAUTION: If the sill support bolts do not contact the window sill, or if you have a window without a sill, you must order accessory kit RAK87 to properly install this air conditioner.

???All supporting parts must be secured to firm wood, masonry or metal.

???The electrical outlet must be within reach of the power cord.

REMOVE THE AIR CONDITIONER

FROM THE CASE

ARemove and save the 2 screws from the lower sides of the front grille.

BGrasp the lower corners of the grille while pressing in on the case sides with your finger tips. Pull out to release and lift it up.

NOTE: Do not pull the bottom edge toward you more than 3 ?? or you may damage the tabs of the grille.

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air conditioner to tilt toward the outside, and will keep it from draining properly. To adjust for this, attach a piece of wood to the sill.

WOOD PIECES ???

WIDTH: 2???

ESlide the air conditioner from the case by gripping the base pan handle and pulling forward while bracing the case. Do not pull or lift on the styrofoam discharge area.

ATTACH THE TOP MOUNTING

RAIL SEAL STRIP

Remove the backing from the top mounting rail seal strip and attach the seal strip to the bottom of the top mounting rail, along the front edge. Allow the seal strip to overlap 3/8??? on each end.

INSTALL THE

SIDE ACCORDION PANELS

ASlide the left and right accordion panels into the top and bottom mounting rails.

BAttach the accordion panels to the case using 3 Type A screws on each side.

Top mounting rail

3/8???

Remove backing from seal strip

3/8???

PREPARE THE WINDOW

???Cut the window sash seal to the window width and stick the adhesive side to the bottom of the sash.

3/8??? overlap Seal strip 3/8??? overlap

INSTALL THE TOP MOUNTING

Window sash seal

RAIL ONTO THE CASE

Attach the top mounting rail onto the top

INSIDE

of the case with 3 Type B screws.

9 SECURE THE CASE IN WINDOW AND

INSTALL FOAM TOP WINDOW GASKET

Attach the window locking brackets (one on each side) with Type C screws.

BCut the foam top window gasket to the window width.

C Stuff the foam between the glass and the

window to prevent air and

insects from getting into the room.

NOTE: If the gasket supplied does not fit your window, obtain appropriate material locally to provide a proper installation seal.

10INSTALL THE AIR CONDITIONER

IN THE CASE

ASlide the air conditioner into the case by the base pan. Do not push on the controls, styrofoam air discharge housing or the finned coils. Make sure the air conditioner is firmly seated.

Replace the 2 ground screws removed earlier, one on each side of the case.

IMPORTANT: The ground screws must be reinstalled to ensure a proper ground.

Attach the front grille to the case by inserting the tabs on the grille into the slots on the front top of the case. Push the grille in.

Secure the front grille to the case by replacing the 2 screws removed earlier. Press on the top of the grille to help with side screw installation.

Connect power.