Important safety instructions

1.Read these instructions.

2.Keep these instructions. Always include these instructions when passing the devices on to third parties.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use the devices near water.

6.Clean only with a dry cloth.

7.Do not block any ventilation openings. Install in accordance with these instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.

9.The devices should be operated only from the type of power source indicated on the mains plug. The devices must only be connected to properly grounded power outlets.

10.Protect the mains cable from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the device.

11.Only use attachments/accessories specified by Sennheiser.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip- over.

13.Unplug the devices during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel.

Servicing is required if the device has been damaged in any way, such as mains cable or plug damage, liquid has been spilled, objects have fallen inside, the device has been exposed to rain or moisture, does not operate properly or has been dropped.

15.To completely disconnect the devices from the AC mains, disconnect the mains plug from the AC receptacle.

16.WARNING: To reduce the risk of fire or electric shock, do not expose the devices to rain or moisture.

17.Do not expose the devices to dripping or splashing and ensure that no objects filled with liquids, such as vases or coffee cups, are placed on the devices.

18.The plug of the mains cable shall remain readily operable and easily accessible.

2

Hazard warnings on the rear of the transmitter (SR 350 IEM G2 only)

The label shown on the left is attached to the rear of the transmitter. The symbols on this label have the following meaning:

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the transmitter???s enclosure that may be of sufficient magnitude to constitute risk of fire or electric shock.

This symbol is intended to alert the user to the risk of electric shock if the transmitter is opened. There are no user serviceable parts inside. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying this transmitter.

Overloading

Do not overload wall outlets and extension cables as this may result in fire and electric shock.

Replacement parts

When replacement parts are required, be sure the service technician has used replacement parts specified by Sennheiser or those having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

Safety check

Upon completion of any service or repairs to this device, ask the service technician to perform safety checks to determine that the device is in safe operating order.

Danger due to high volumes

This is a professional transmission system. Commercial use is subject to the rules and regulations of the trade association responsible. Sennheiser, as the manufacturer, is therefore obliged to expressly point out possible health risks arising from use.

This system is capable of producing sound pressure exceeding 85 dB(A). 85 dB(A) is the sound pressure corresponding to the maximum permissible volume which is by law (in some countries) allowed to affect your hearing for the duration of a working day. It is used as a basis according to the specifications of industrial medicine. Higher volumes or longer durations can damage your hearing. At higher volumes, the duration must be shortened in order to prevent hearing damage. The following are sure signs that you have been subjected to excessive noise for too long a time:

yYou can hear ringing or whistling sounds in your ears.

yYou have the impression (even for a short time only) that you can no longer hear high notes.

Reception interference due to high transmission power

The SR 350 IEM G2 twin transmitter can be switched to a transmission power of 100 mW. Depending on the selected frequency, this can affect the reception of other wireless systems.

3

Intended use of the devices

Intended use of the ew 300 IEM G2 series devices includes:

yusing the devices for professional purposes,

yhaving read these instructions especially the chapter ???Important safety instructions??? on page 2,

yusing the devices within the operating conditions and limitations described in this instruction manual.

???Improper use??? means using the devices other than as described in these instructions, or under operating conditions which differ from those described herein.

The ew 300 IEM G2 systems

With the Sennheiser evolution wireless in-ear monitoring systems ew 300 IEM G2 (suitable for both stage and broadcast use), musicians, video and sound amateurs, reporters/broadcasters, etc. can directly monitor the received sound signals without troublesome cables or monitor speakers being required. In addition, the system can also be used for any application where talkback signals are to be transmitted.

The evolution wireless in-ear monitoring systems ew 300 IEM G2 are high- quality state-of-the-art RF transmission systems with a high level of operational reliability and ease of use. The transmitters and the receiver permit wireless transmission with studio-quality sound. The excellent transmission reliability of the ew 300 IEM G2 systems is based on the use of

yfurther optimized PLL synthesizer and microprocessor technology,

ythe HDX noise reduction system,

ythe pilot tone squelch control (during stereo operation),

yand the scan function for scanning the channel banks for free channels.

The ew 300 IEM series offers two systems:

ythe ew 300 IEM G2 system

(SR 300 IEM G2 stereo transmitter, EK 300 IEM G2 stereo receiver)

yand the SR 350 IEM G2 twin transmitter

The EK 300 IEM G2 can also be used with the SR 350 IEM G2 twin transmitter. The SR 350 IEM G2 twin transmitter consists of two complete SR 300 IEM G2 stereo transmitters, but offers some advantages such as

yeasy rack mounting,

ya built-in mains unit

yand a switchable transmission power for optimum operational reliability under varying transmission conditions.

4

The channel bank system

The ew 300 IEM G2 systems are available in six UHF frequency ranges with 1440 transmission/receiving frequencies per frequency range. Please note: Frequency usage is different for each country. Your Sennheiser agent will have all the necessary details on the available legal frequencies for your area:

The transmitters and the receiver of the ew 300 IEM G2 systems have nine channel banks with up to 12 switchable channels each.

The channel banks ???1??? to ???8??? have up to 12 switchable channels that are factory-preset to a transmission/receiving frequency (see enclosed frequency table). These transmission/receiving frequencies cannot be changed but have been preset so that e.g. country-specific regulations on frequency usage are taken into account (see ???Type approvals??? on page 39). For detailed information, please refer to the enclosed frequency data sheets and to the country-specific frequency and transmission power overviews.

An advantage of the factory-preset frequencies is that

ythe system is ready for immediate use after switch-on,

yseveral transmission systems can be operated simultaneously on the preset channels without causing intermodulation interference.

Delivery includes

Depending on the purchased system, delivery includes:

5

Overview of operating controls

Stereo transmitter ??? front view (SR 350 IEM G2 twin transmitter)

6

Stereo transmitter ??? rear view

Operating controls on the SR 350 IEM G2 twin transmitter

            

 3-pin IEC mains socket

 Cable grip for power supply DC cable

 Label with hazard warnings

 Type plate

Service interface;

connection to the NET 1 network system

 Audio input (AF IN BAL/UNBAL), XLR-3F socket (left and MONO)

 Audio input (AF IN BAL/UNBAL), XLR-3F socket (right)

 Antenna output (ANT A/B), BNC socket

 Transmission power switch (RF POWER)

Operating controls on the SR 300 IEM G2 transmitter

    

 DC socket for connection of mains unit (DC IN)

 Cable grip for power supply DC cable

 Type plate

 Service interface (DATA)

 Audio input (AF IN BAL/UNBAL), XLR-3F socket (left and MONO)

 Audio input (AF IN BAL/UNBAL), XLR-3F socket (right)

 Antenna output (ANT), BNC socket

7

EK 300 IEM G2 stereo receiver



 







8

Indications and displays on the transmitter

Modulation display

The level display for audio signal ???AF??? shows the modulation of the transmitter.

When the transmitter???s audio input level is excessively high, the level display for audio signal ???AF??? shows full deflection.

When the transmitter is overmodulated frequently or for an extended period of time, the text ???PEAK??? (backlit in red) flashes in alternation with the standard display.

Button backlighting

During standby operation, the ON button  is backlit in red. When the transmitter is switched on, the SET button  and the / button ! are additionally backlit in green.

  

Indications and displays on the receiver

Modulation display of the received transmitter

The level display for audio signal ???AF??? shows the modulation of the received transmitter.

When the transmitter???s audio input level is excessively high (AF peak), the receiver???s level display for audio signal ???AF??? shows full deflection.

9

RF signal indication

The green LED (RF) ! at the front of the receiver lights up when an RF signal is being received.

However, the green LED (RF) does not light up when the audio output is muted because

y the RF signal of the received transmitter is too weak,

 y the transmitter is set to mono operation and the receiver???s pilot tone evaluation is deactivated.

Display backlighting

After pressing a button, the display remains backlit for approx. 15 seconds.

10

Preparing the devices for use

SR 300 IEM G2 transmitter/

SR 350 IEM G2 twin transmitter

Fitting the device feet

To ensure that the transmitter cannot slip on the surface on which it is placed, four self-adhesive soft rubber feet are supplied.

Note:

Do not fit the rubber feet when rack mounting the transmitter.

CAUTION! Risk of staining of furniture surfaces!

Some furniture surfaces have been treated with varnish, polish or synthetics which might cause stains when they come into contact with other synthetics. Despite a thorough testing of the synthetics used by us, we cannot rule out the possibility of staining.

Do not place the transmitter on delicate surfaces.

Ensure that the base of the transmitter is clean and free from grease before mounting the rubber feet.

Fix the rubber feet to the base of the transmitter by peeling off the safety paper and fitting them as shown in the digram on the left.

Rack mounting

CAUTION! Risks when rack mounting the transmitter!

When installing the device in a closed or multi-rack assembly, please consider that, during operation, the ambient temperature within the rack may significantly rise above room temperature.

The ambient temperature within the rack must not exceed the temperature limit specified in the specifications.

When installing the device in a rack, take good care not to affect the ventilation required for safe operation or provide additional ventilation.

Make sure the mechanical loading of the rack is even to avoid a hazardous condition such as a severely unbalanced rack.

When connecting the device to the power supply, observe the information indicated on the type plate. Avoid circuit overloading. If necessary, provide overcurrent protection.

Ensure a reliable mains ground connection of the device by taking appropriate measures.

When installing the device in a closed or multi-rack assembly, please note that intrinsically harmless leakage currents of the individual devices may accumulate, thereby exceeding the allowable limit value. As a remedy, ground the rack via an additional ground connection.

11



 

Place the two transmitters side by side upside-down onto a flat surface.

Align the jointing plate  over the holes in the bottom sides of the transmitters.

Secure the jointing plate  to the transmitters using eight of the supplied recessed head screws (M 3x6).

Hook the two rack mount ???ears???  to the front panels of the transmitters.

Secure the rack mount ???ears??? to the transmitters using two of the supplied recessed head screws (M 3x6) respectively.

Slide the transmitters into the 19??? rack.

Secure the rack mount ???ears??? to the rack.

12

Antenna front mounting When mounting only one SR 300 IEM G2 transmitter or one SR 350 IEM G2 twin transmitter into a rack, you can use an antenna mount (optional accessory) to mount the transmitter???s antenna connection to the front of the rack.

Use the antenna mount matching the respective transmitter:

yFor the SR 300 IEM G2 transmitter: AM 2 antenna mount

yFor the SR 350 IEM G2 twin transmitter: GA 3030 AM antenna mount

13

The antenna mounts consist of:

y 2 BNC extension cables (screw-in BNC socket to BNC connector ) y 2 washers

y 2 nuts

y 2 antenna holders (GA 3030 AM only) y 4 screws (GA 3030 AM only)

To front mount the antenna of the SR 300 IEM G2 transmitter:



 Screw the BNC socket of the BNC extension cables to the blanking plate  using the supplied washer and nut.

 Screw the antenna holders to the BNC sockets using the supplied washers and nuts.

 Secure the antenna holders to the handles of the twin transmitter using two of the supplied screws respectively.

14

Connect the two BNC connectors to the BNC sockets  on the twin transmitter.

Slide the twin transmitter into the 19?????? rack.

Resecure the rack mount ???ears???  to the rack .

Connect the telescopic antennas to the BNC sockets .

Pull the end caps to extend the telescopic antennas .

Changing the transmission power (SR 350 IEM G2 only)

With the SR 350 IEM G2 twin transmitter, you can choose between two different transmission powers.

ATTENTION! Danger of interference with other transmitters!

Depending on the selected transmission power and frequency, you may have to apply for an approval from the respective authority for a radio transmission licence, as you could interfere with other transmitters. This approval will only be valid for the approved transmission power. For detailed information, please refer to the enclosed frequency data sheets and to the country- specific frequency and transmission power overviews.

Apply for an approval, should country-specific regulations on frequency and/or transmission power usage require this.

ATTENTION! Danger of damage to the device!

Due to the high transmission power (100 mW) in the switch position ???STANDARD???, the optional AC 2 transmitter combiner must not be used as this can cause damage to the devices.

Use only the optional AC 3200 transmitter combiner (see ???Accessories and spare parts??? on page 40).

Set the transmission power switch (RF POWER)  to the desired position.

Transmission power will change as follows:

15

16

Service interface/ connection to the NET 1 network system

The service interface (DATA A/B)  is only required for servicing purposes. In addition, the interface can also be used for connecting the transmitter to the NET 1 network system. For detailed information, please refer to the user manual of the NET 1.



17

Connecting the headphones

CAUTION! Danger of hearing damage!

Listening at high volume levels for long periods can lead to permanent hearing defects.

Set the volume for the connected headphones to the minimum before putting the headphones on.

For monitoring purposes, connect the supplied earphones or any

Sennheiser stereo headphones with 3.5 mm stereo jack plug to the headphone output (PHONES) .

 First, set the volume control  to the lowest volume by turning it to the left as far as possible. Then gradually turn up the volume.





Using the components

Switching the components on/off

Switching the transmitter on/off

Press the ON button  to switch the transmitter on.

To switch the transmitter off, press the ON button until ???OFF??? appears on

the display.

Note:

The transmitter can only be switched off when the standard display is shown on the display panel. Within the operating menu, the ON button

serves as the ESC (cancel) key, i.e. you cancel your entry and return to the standard display.

After switch-off, the transmitter is in standby mode. To disconnect the transmitter from the mains, pull out the mains connector from the wall socket!

18

Adjusting the volume

CAUTION! Danger of hearing damage!

Listening at high volume levels for long periods can lead to permanent hearing defects.

 Set the volume for the connected headphones to the minimum before putting the headphones on.

Adjusting the balance

During stereo operation ??? and provided that the standard display is shown on the display panel ??? the / rocker button  serves to adjust the balance between the left and right stereo signal.

During FOCUS operation, the / rocker button  serves to adjust the relative levels of the two separate channels in the mixed mono signal (see ???Stereo/FOCUS selection (receiver only)??? on page 30).



Activating/deactivating the lock mode

Transmitter and receiver have a lock mode that can be activated or deactivated via the operating menu (see ???Activating/deactivating the lock mode??? on page 33). The lock mode prevents that

y the transmitter is accidentally programmed or switched off during

y the balance setting is accidentally changed via the receiver???s / rocker button.

EK 300 IEM G2

Attaching the receiver to clothing

The receiver is attached to clothing (e.g. belt, waistband) with the supplied belt clip.

19

The operating menu

To ensure intuitive operation of both transmitter and receiver, the operating menus have been largely standardized. As a result, adjustments to the settings can be made quickly and ???without looking??? ??? even in stressful situations, for example on stage or during a live show or presentation.

The buttons

20

Overview of menus

Working with the operating menu

By way of example of the ???Tune??? menu, this section describes how to use the operating menu.

After switching the unit on, the standard display is shown on the display panel.

SR 300 IEM G2/SR 350 IEM G2

EK 300 IEM G2

21

Getting into the operating menu

Press the SET button to get from the standard display into the operating menu.

The last menu selected flashes on the display. With the transmitter, the current setting is additionally displayed.

Selecting a menu

Press the / rocker button to select a menu.

Press the SET button to get into the setting mode of the selected menu. With the receiver, the current setting that can be adjusted flashes on the display. With the transmitter, the name of the menu and the current setting are displayed.

Adjusting a setting

Press the / rocker button to adjust the setting.

By briefly pressing the / rocker button, the display jumps either

forwards or backwards to the next setting. In the ???Channel???, ???Tune??? and ???Name??? menu, the / rocker button features a ???fast search??? function. If you hold down a button, the display cycles continuously. The ???fast search??? function allows you to get fast and easily to your desired setting. With the receiver, the new setting flashes on the display until it is stored.

Storing a setting

Press the SET button to store the setting. ???Stored??? appears on the display, indicating that the setting has been stored. The display then returns to the top menu level.

With most menus, new settings become effective immediately without having to be stored. An exception are the ???Bank???, ???Channel???, ???Tune??? and ???Reset??? menus of the transmitter and the ???RESET??? menu of the receiver. With these menus, new settings only become effective after they have been stored (???Stored??? appears on the display, indicating that the setting has been stored).

Exiting the operating menu

Select the ???Exit??? menu to exit the operating menu and to return to the standard display.

When you have entered the operating menu, the transmitter???s ON button serves as the ESC (cancel) key, i.e. by briefly pressing this button, you cancel your entry and return to the standard display. The receiver has a separate ESC button with which you can cancel your entry.

22

Operating menu of the stereo transmitter

SET

23

24

Operating menu of the stereo receiver

EXIT

STORED

ST--FOC

25

26

27

28

29

30

Selecting the standard display

???NAME???

???CHAN???

31

32

Stereo/mono selection (transmitter only)



33

If a problem occurs ...

Error checklist

If a problem occurs that is not listed in the above table or if the problem cannot be solved with the proposed solutions, please contact your local Sennheiser agent for assistance.

34

Recommendations and tips

... for the EK 300 IEM G2 receiver

yThe antenna should hang freely and be at least 1 cm away from the body. The antenna must not be in direct contact with the skin.

... for optimum reception

yTransmission range depends to a large extent on location and can vary from about 10 m to about 150 m. There should be a ???free line of sight??? between transmitting and receiving antennas.

yIf, with the SR 300 IEM G2 transmitter or the SR 350 IEM G2 twin receiver, transmission conditions are unfavourable, you should use a remote antenna which is connected via antenna cable.

yTo avoid overmodulating the receiver, observe a minimum distance of 5 m between transmitting and receiving antennas.

yObserve a minimum distance of 50 cm between the transmitting antennas and metal objects (such as cross members or reinforced-concrete walls).

... for multi-channel operation

yFor multi-channel operation, you can only use the channels in a channel bank. Each of the channel banks ???1??? to ???8??? accommodates up to 12 factory-preset frequencies which are intermodulation-free. For alternative frequency combinations, please refer to the enclosed frequency table. The freely selectable frequencies can be selected via the ???Tune??? menu and can be stored in the channel bank ???U???.

yWhen using several transmitters simultaneously, interference can be avoided by maintaining a minimum distance of 20 cm between two transmitters. For multi-channel applications, use the appropriate transmitter combiners (see ???Accessories and spare parts??? on page 40):

ySR 300 IEM G2 stereo transmitter: AC 2 transmitter combiner

ySR 350 IEM G2 twin transmitter:

AC 2 transmitter combiner (only when the transmission power is set to ???LOW???) or AC 3200 transmitter combiner

Care and maintenance

Use a slightly damp cloth to clean the units from time to time.

Note:

Do not use any cleansing agents or solvents.

35

Additional information

HDX noise reduction

RF link

Progress you can hear:

The evolution wireless G2 series is equipped with HDX, the Sennheiser noise reduction system that reduces RF interference. It increases the signal-to- noise ratio in wireless audio transmission to more than 110 dB.

HDX is a wideband compander system which compresses the audio signal in the transmitter in a 2:1 ratio (related to dB) to lift it above the inherent noise floor of the RF link. In the receiver the signal is expanded in an identical and opposite way in a 1:2 ratio to restore the original signal, at the same time reducing the RF noise to below the noise floor of the receiver.

HDX has been specially developed for high quality radiomicrophone systems.

Note:

Only transmitters and receivers that are equipped with HDX can work correctly with each other. If non HDX equipment was mixed with HDX, the dynamic range would be drastically reduced and the transmission would sound blunt and flat. HDX is permanently active and cannot be switched off.

Wireless transmission systems

With the ew 300 IEM G2 system, Sennheiser puts an end to cable tangles and enables complete freedom of movement. The systems operate exclusively in the UHF band. UHF transmission is extremely reliable and is far less prone to interference than the overcrowded VHF band ??? harmonics from mains units, fluorescent tubes, refrigerators, computers, etc. are virtually eliminated. Also indoor propagation of UHF radio waves is better than VHF so that the RF power can be kept low ??? this is also an advantage when using multi-channel systems. Finally, UHF frequency ranges are being approved all over the world for radiomicrophone usage ??? in some countries licence-free.

Correct adjustment of transmitter sensitivity is vital. Too high and you get overmodulation and distortion, too low and you get undermodulation and a noisy signal. Please set the sensitivity correctly for the microphone/usage and check it before every performance to ensure best operation.

36

Squelch

Pilot tone squelch

The transmitter adds a 19-kHz pilot tone to the audio signal. The receiver checks incoming audio signals to see if the pilot tone is present. In the absence of the 19-kHz signal, the receiver???s audio output will remain muted, even if a strong RF signal is present.

This prevents strong interfering signals from causing hissing noise in the receiver when the transmitter is switched off.

Field strength-dependent squelch

Depending on the strength of the received RF signal, the receiver???s audio output is opened or muted. Via the ???SQELCH??? menu of the receiver, the squelch threshold can be adjusted in three steps (LO, MID, HI).

37

Specifications

AF characteristics

Headphone output3.5 mm jack socket

AF output voltage (peak deviation, 1 kHzAF) PHONES 2 x ??? 100 mW at 32 ??

38

SR 300 IEM G2 transmitter/SR 350 IEM G2 twin transmitter

Type approvals

Connector assignment

39

Accessories and spare parts

Cat. No. Accessory/spare part

009823 GA 2:

19?????? rack adapter

009912 AM 2 (for SR 300 IEM G2):

Antenna mount for mounting antennas to the front of the GA 2 rack adapter

004645 A 1031-U:

UHF antenna, passive, omni-directional, can be mounted onto a stand

003658 A 2003 UHF:

UHF antenna, passive, directional, can be mounted onto a stand

004368 GA 3030-AM (for SR 350 IEM G2):

Antenna mount

002324 GZL 1019-A1:

Antenna cable with BNC connectors, length: 1 m

002325 GZL 1019-A5:

Antenna cable with BNC connectors, length: 5 m

009822 AC 2:

Transmitter combiner, for combining the RF signals of up to four transmitters onto a single antenna and for powering up to four transmitters

502048 AC 3200:

Transmitter combiner, for combining the RF signals of up to eight trans- mitters onto a single antenna and for powering up to eight transmitters

004863 NT 3:

Plug-in mains unit for AC2

500432 IE 4:

1 pair of earphones with medium ear sleeves

512814 IES 4???L:

Ear sleeves, large (10 pieces)

512815 IES 4???M:

Ear sleeves, medium (10 pieces)

512816 IES 4???S:

Ear sleeves, small (10 pieces)

009950 BA 2015:

Accupack

009828 L 2015:

Charger for BA 2015 accupack

009826 CC 2:

Carrying case for ew 300 IEM G2 system

40

Manufacturer Declarations

Warranty

The original Sennheiser product you have purchased is covered by a warranty of 24 months. The warranty period begins on the date of purchase of brand new, unused products by the first end user. Please retain your sales receipt (or your warranty certificate) as proof of purchase. Unless you submit proof of purchase, which will be verified by your local Sennheiser service partner, you will be obliged to pay for any repairs that are carried out. Proof of purchase must state the date of purchase and name of the product.

We shall satisfy our warranty obligations by remedying any material or manufacturing faults free of charge at our discretion either by repair or by exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of Sennheiser electronic GmbH & Co. KG.

The following cases are not covered by the above warranty:

yminor faults or deviations in the quality of a product which do not affect the product's value or fitness for its intended purpose

yany accessories supplied with the product

yrechargeable and disposable batteries (these products have a shorter service life, the length of which also depends on the frequency of use)

yfaults resulting from improper use (e.g. operating errors, mechanical damage, incorrect operating voltage)

Proper use for the purposes of this warranty is defined as use of the product under the conditions stated in the instructions for use.

yfaults due to wear and tear

yany modification of Sennheiser products effected by you or a third party, unless Sennheiser has given its prior written consent to the nature and extent of the modification

yfaults due to force majeure

yfaults of which the purchaser was already aware at the time of purchase

All warranty claims become void if the product is tampered with by unauthorised persons or repair shops.

Warranty claims can be enforced in any country throughout the world in which the statutory rights of the country concerned are not in conflict with our warranty regulations. No other warranty claims or claims over and above the rights stated in these terms and conditions will be accepted.

Consumers may be entitled to statutory rights in their own countries which are not restricted by these warranty terms and conditions, as the warranty is governed by the laws of the country in which the Sennheiser product was purchased by the consumer. The provisions of the UN Convention on the International Sale of Goods do not apply to this service.

If you wish to file a claim under the warranty, please send the product to your local service partner, together with accessories and proof of purchase.

An up-to-date list of all service partners of Sennheiser electronic GmbH & Co. KG worldwide are available on the internet at www.sennheiser.com.

The customer bears the risk of shipment. To avoid any damage in transit, please use the original packaging if possible.

41

This equipment is in compliance with the essential requirements and other relevant provisions of Directives 1999/5/EC, 2004/108/EU or 2006/95/EC. The declaration is available on the internet site at www.sennheiser.com.

Before putting the equipment into operation, please observe the respective country-specific regulations!

Batteries or rechargeable batteries

The supplied batteries or rechargeable batteries can be recycled. Please dispose of them as special waste or return them to your specialist dealer. In order to protect the environment, only dispose of exhausted batteries.

WEEE Declaration

Your Sennheiser product was developed and manufactured with highquality materials and components which can be recycled and/or reused. This symbol indicates that electrical and electronic equipment must be disposed of separately from normal waste at the end of its operational lifetime. Please dispose of this product by bringing it to your local collection point or recycling centre for such equipment. This will help to protect the environment in which we all live.

Statements regarding FCC and industry Canada

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

This class B digital apparatus complies with the Canadian ICES-003

Changes or modifications made to this equipment not expressly approved by Sennheiser electronic Corp. may void the FCC authorization to operate this equipment.

42