CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LASER CLASE 1

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE REAR COVER.

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a CLASS 1 LASER product.

Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION-INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCKS

DEFEATED, AVOID

EXPOSURE TO BEAM.

Note to CATV system installer :

This reminder is provided to call the CATV system installer???s attention to Section 820~40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical

FCC compliance Information

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received. Including interference that may cause undesired operation.

Information to User

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

During thunderstorms, disconnect AC main plug from the wall outlet.

Voltage peaks due to lightning could damage the unit.

Protect the player from moisture(i.e. vases) , and excess heat(e.g.fireplace) or equipment creating strong magnetic or electric fields (i.e.speakers...). Disconnect the power cable from the AC supply if the player malfunctions. Your player is not intended for industrial use. Use of this product is for personal use only.

Condensation may occur if your player or disc have been stored in cold temperatures.

If transporting the player during the winter, wait approximately 2 hours until the unit has reached room temperature before using.

Do not expose the unit to direct sunlight or other heat sources.

This could lead to overheating and malfunction of the unit.

The battery used with this product contain chemicals that

are harmful to the environment.

Do not dispose of batteries in the general household trash.

2

READ INSTRUCTIONS

All the safety and operating instructions should be read before the appliance is operated.

RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

HEED WARNINGS

All warnings on the appliance and in the operating instructions should be adhered to.

FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

WATER AND MOISTURE

Do not use this video product near water- forexample, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

OVERLOADING

Do not overload wall outlets and extension cords as this can result in the risk of fire

or electric shock.

VENTILATION

Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the video product and to protect it from overheating these openings must not be blocked or covered. The openings should never be blocked

by placing the video product on a bed, sofa, rug, or other similar surface. This video product

should never be placed near or over a radiator or heat register.

This video product should not be placed

in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been followed.

POWER CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

CLEANING

Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners

or aerosol cleaners. Use a damp cloth for cleaning.

LIGHTNING

For added protection of this video product receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges.

OBJECT AND LIQUID ENTRY

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.

ACCESSORIES

Do not place this video product on an unstable cart, stand, tripod, bracket, or table.

The video product may fall, causing serious injury to a child or adult, and serious damage

to the appliance.

Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting

of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.

CART

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

POWER SOURCES

This video product should be operated only from the type of power source indicated

on the marking label. If you are not sure

of the type of supply to your home, consult your appliance dealer or local power company.

For video products intended to be operated from battery power, or other sources, refer

to the operating instructions.

POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits,

or where it can fall into such power lines

or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

POLARIZATION

This video product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other.) This plug will fit into the power outlet only one way.

This is a safety feature. If you are unable

to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

OUTDOOR ANTENNA GROUNDING

???If an outside antenna is connected to the antenna terminal, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

???In the U.S.A section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See the figure below.

ATTACHMENTS

Do not use attachments not recommended

by the video product manufacturer as they may cause hazards.

SERVICING

???Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards.

???Refer all servicing to qualified service personnel.

REPLACEMENT PARTS

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

SAFETY CHECK

Upon completion of any service or repairs

to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.

DAMAGE REQUIRING SERVICE

Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions.

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the video product.

c.If the video product has been exposed to rain or water

d.If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result

in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.

e.If the video product has been dropped or the cabinet has been damaged.

f.When the video product exhibits a distinct change in performance - this indicates

a need for service.

HEAT

This video unit should be situated away from heat sources such as radiators, stoves, or other products (including amplifiers) that produce heat.

PREPARATION

5

You can conveniently operate Samsung DVD and other Samsung AV devices with one remote controller of Samsung TV, using Anynet.

Contents

PREPARATION

CONNECTIONS

OPERATION

SETUP

RADIO OPERATION

MISCELLANEOUS

PREPARATION

V I D E O

1 ~ 6

DVD (Digital Versatile Disc) offers fantastic audio and video, thanks to Dolby Digital surround sound and MPEG-2 video compression technology. Now you can enjoy these realistic effects in the home, as if you were in a movie theater or concert hall.

DVD players and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.

The Region Number for this player is given on the rear panel of the player.

(Your DVD player will only play DVDs that are labeled with identical region codes.)

Disc Recording Format

CD-R Discs

???Depending on the disc recording device (CD-Recorder or PC ) and the condition of the disc, some CD-R discs may not be playable.

???Use a 650MB/74 minute CD-R. Avoid CD-R media, as they may not be playable.

???If possible, do not use CD-RW (Rewritable) media, as they may not be playable.

???Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open, you may not be able to fully play the disc.

CD-R MP3 Discs

???Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.

???MP3 file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).

???Use discs recorded with a compression/decompression data rate greater than 128Kbps.

???Only files with the ".mp3" and ".MP3" extensions can be played.

???Only a consecutively written Multisession disc can be played. If there is a blank segment in the Multisession disc, the disc can be played only up to the blank segment.

???If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.

???For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate (e.g., 32Kbps ~ 320Kbps), the sound may skip during playback.

???If more than 500 tracks are recorded on a single CD, a maximum of 500 tracks can be played.

???If more than 300 folders are recorded on a single CD, a maximum of 300 folders can be played.

CD-R JPEG Discs

???Only files with the ".jpeg" and ".JPEG" extensions can be played.

???If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.

???Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.

???JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).

???Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc, the disc can be played only up to the blank segment.

???A maximum of 9,999 images can be stored on a single CD.

???When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.

???Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.

PREPARATION

???Rear Panel???

Speaker Output

External Digital in Optical 1 Input

Connector

Use this to connect external equipment capable of digital output.

PREPARATION

Terminals

External Video Component

Input Connectors

AM Antenna

External Audio Component

Input Connector

REAR SPEAKER

ANTENNA

Connector

FM Antenna

Connector

REAR SPEAKER ANTENNA

Connector

ANYNET

OUTPUT/INPUT

Connector

S-Video Output Connector

If the TV is equipped with an S-Video input connector (S-VIDEO IN), connect it to the player's S-Video output jack.

TV, DVD POWER button TV/VIDEO, DIMMER button OPEN/CLOSE button

Auto Sound Calibration button

SUPER 5.1 button Live Surround Mode button/ Virtual Headphone button

PL II MODE button

VOLUME button

MENU button

RETURN button

DVD RECEIVER indicator

MODE button

DVD button

TUNER BAND button

DISC SKIP button

SLOW, MO/ST button

MOVIE button

Play/Pause button Stop button

Tuning Preset/CD Skip button PL II EFFECT button

TUNING/CH button

INFO button

MUTE button

Direction/Enter button

TEST TONE button SOUND EDIT button

TUNER MEMORY, P.SCAN button ZOOM button

CANCEL button

REMAIN button

REPEAT button

Insert Remote Batteries

PREPARATION

Range of Operation of the Remote Control

The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be operated at a horizontal angle of up to 30?? from the remote control sensor.

To open the remote control cover, push the top of the cover, then slide downward.

???Place it on a stand or cabinet shelf, or under the TV stand.

The listening position should be located about 2.5 to 3 times the distance of the TV's screen size away from the TV. Example: For 32" TVs 2~2.4m (6~8feet)

For 55" TVs 3.5~4m (11~13feet)

Front Speakers L R

???Place these speakers in front of your listening position, facing inwards (about 45??) toward you.

???Place the speakers so that their tweeters will be at the same height as your ear.

???Align the front face of the front speakers with the front face of the center speaker or place them slightly in front of the center speakers.

Center Speaker C

???It is best to install it at the same height as the front speakers.

???You can also install it directly over or under the TV.

Rear Speakers LS RS

???Place these speakers behind your listening position.

???If there isn't enough room, place these speakers to face each other.

???Place them about 60 to 90cm (2 to 3feet) above your ear, facing slightly downward.

*Unlike the front and center speakers, the rear speakers are used to handle mainly sound effects and sound will not come from them all the time.

Subwoofer SW

???The position of the subwoofer is not so critical. Place it anywhere you like.

???Usually, it is placed by a corner near the front speakers.

Center Speaker

Front Speaker (L)

REAR SPEAKER ANTENNA

GreenWhite

Front Speaker (R)

Wireless Rear Amplifier (SWA-1000) (With built-in wireless receiving antenna)

Subwoofer

CONNECTIONS

Back of the Speakers

Back of the Main Unit

3 Connect the connecting plugs to the back of the DVD player.

???Make sure the colors of the speaker terminals match the colors of the connecting plugs.

Connecting Wireless Rear Speakers

Back of Wireless Rear Amplifier

Caution

???Do not connect the wireless rear speakers to the speaker outputs on the back of the main unit. Malfunction may result.

???The wireless receiving antenna is built into the wireless rear amplifier.

Keep the unit away from water and moisture.

???For optimal listening performance, make sure that the area around the proposed wireless rear amplifier location is clear of any obstructions.

2

3

With the wireless rear amplifier turned on, use a ball point pen or a pair of tweezers to press the RESET button on the back of the unit 2 to 3 times.

Turn on the main unit.

???The wireless rear amplifier's synchronizing signal indicator will light up.

???If Power Standby mode continues, repeat Steps 1 to 3 above.

Back of Wireless Rear Amplifier

Caution

???Sound will be heard from the wireless rear speakers in DVD 5.1-CH or Dolby Pro Logic II mode only.

???In 2-CH mode, no sound will be heard from the wireless rear speakers.

P.SCAN(Progressive Scan) Function

Unlike regular Interlace Scan, in which two fields of picture information alternate to create the

entire picture (odd scan lines, then even scan lines), Progressive Scan uses one field of information (all lines displayed in one pass) to create a clear and detailed picture without visible scan lines.

1 Press STOP button.

??? When disc is played back, press the STOP button twice so that ???STOP???, appears on the display.

2 Press and hold P.SCAN button on the remote control for over 5 seconds.

???Pressing and holding the button for over 5 seconds will select "Progressive Scan" and "Interlace Scan" repetitively.

???When you select P.SCAN, "P.SCAN" will appear on the display

What is Progressive (or Non-Interlaced) Scanning?

Selecting the Video Format

Press and hold NTSC/PAL button on the remote controller for over 5 seconds while the power is turned off.

???"NTSC" or "PAL" will appear in the display.

At this time, press the NTSC/PAL button shortly to select between "NTSC" and "PAL".

???Each country has a different video format standard.

CONNECTIONS

Connecting an External Analog Component

Example: Analog signal components such as a VCR or TV.

CONNECTIONS

1 Connect Video Out on the DVD player to Video In on the TV.

2 Connect Video In on the DVD player to Video Out on the external analog component.

3 Connect Audio In on the DVD player to Audio Out on the external analog component.

??? Be sure to match connector colors.

4 Press AUX on the remote control to select AUX 1 or AUX 2.

???Each time the button is pressed, the selection changes as follows: DIGITAL IN ??? AUX 1 ??? AUX 2.

???You can also use the FUNCTION button on the main unit. The mode switches as follows: DVD/CD ??? DIGITAL IN ??? AUX1 ??? AUX2 ??? FM ??? AM.

???If you have connected an external digital component and also an Analog component to Video In (1, 2) at the same time, there will be video from AUX 1 even when you select DIGITAL IN.

???If you have connected Audio In (L, R) to 1, connect Video In to 1 as well, and if you have connected Audio In (L, R) to 2, connect Video In to 2 also.

???When you select Aux 1 or 2, you are selecting Video 1 or 2 inputs respectively.

A

N

T

E

N

N

A

FM Antenna (supplied)

AM Loop Antenna (supplied)

CONNECTIONS

FM antenna connection

1.Connect the FM antenna supplied to the FM 75???

COAXIAL terminal as a temporary measure.

2.Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface.

???If reception is poor, connect an outdoor antenna. Before attaching a 75??? coaxial cable (with a standard type connector), disconnect the supplied FM antenna.

AM antenna connection

1.Connect the AM loop antenna supplied to the AM and terminals.

2.If reception is poor, connect an outdoor single vinyl-covered wire to the AM terminal. (Keep the AM loop antenna connected).

Press TV/VIDEO

4 button to select VIDEO mode.

Press the MODE button so 5 that the DVD RECEIVER

indicator on the remote control flashes.

Press DVD button 6 to select DVD/CD

mode.

Disc terminology

Groups and tracks (DVD-AUDIO)

???DVD-audio is divided into several large sections called "groups" and smaller sections called "tracks". Numbers are allotted to these sections.

These numbers are called "group numbers" and "track numbers".

Titles and chapters (DVD-VIDEO)

???DVD-video is divided into several large sections called "titles" and smaller sections called "chapters". Numbers are allotted to these sections. These numbers are called "title numbers" and "chapter numbers".

Tracks (Video and music CDs)

???Video and music CDs are divided into sections called "tracks". Numbers are allotted to these sections. These numbers are called "track numbers".

CONNECTIONS

1

2

3

4

Press OPEN/CLOSE button to open the disc tray.

Load one or more discs.

???Place a disc gently into the tray with the disc???s label facing up.

Press DISC SKIP button.

???Rotate the carousel tray so you can load the third, fourth, and fifth discs .

Close the compartment by pressing the OPEN/CLOSE button again.

DVD CD

??? Playback starts automatically.

To stop playback,

press STOP during playback.

???If pressed once, ???PRESS PLAY??? is displayed and the

stop position will be stored in memory.

If PLAY/PAUSE ( ) button or ENTER button is pressed, playback resumes from the stop position. (This function works only with DVDs.)

???If pressed twice, ???STOP??? is displayed, and if

PLAY/PAUSE ( ) button is pressed, playback starts from the beginning.

To temporarily pause playback, press PLAY/PAUSE during playback.

???To resume playback, press PLAY/PAUSE ( ) button again.

Selecting a Disc in the Disc changer

The DVD/CD function is automatically selected when Disc Skip is pushed.

To select a specific disc, press the corresponding DIRECT PLAY (1, 2, 3, 4, 5) buttons on the front panel or DISC SKIP on the remote control, until the required disc indicator flashes.

??? All the discs will be played in turn, starting with the one selected.

If you wish to play the current disc only, press REPEAT on the remote control one or more times, until REPEAT : DISC is displayed.

If the disc selected is not loaded, the next disc is played automatically.

CONNECTIONS

Note

??? Depending on the recording mode, some MP3-CDs may not play.

??? Table of contents of a MP3-CD varies depending on the MP3 track format recorded on the disc.

JPEG Disc Playback

Images captured with a digital camera or camcorder, or JPG files on a PC can be stored on a CD and then played back with this unit.

Press the OPEN/CLOSE button to open the disc tray, and then load the JPEG disc.

???Playback will start automatically and each image will show for 5 seconds before moving to the next image.

To rotate the image

OPERATION

DVD

Display disappears

Something like you

Back for good

Love of my life

More than words

??? appears on the TV screen!

If this symbol appears on the TV screen while buttons are being operated, that operation is not possible with the disc currently being played.

???Depending on the disc, the disc information display may appear different.

???Depending on the disc, you can also select DTS, DOLBY DIGITAL, or PRO

LOGIC.

Screen Display

???

???

???

???

What is a Group?

A group of tracks contained in a DVD-AUDIO disc.

What is a Title?

A movie contained in a DVD-VIDEO disc.

What is a Chapter?

Each title on a DVD disc is divided into several smaller sections called "chapters".

What is a Track (File)?

A section of video or a music file recorded on a DVD-AUDIO, CD, or MP3-CD.

Press the REMAIN button.

???For checking the total and remaining time of a title or chapter being played.

Each time the REMAIN button is pressed

OPERATION

1p~42p(DS690)-SEA 9/15/04 5:00 PM Page 35

Skipping Scenes/Songs

DVD MP3

Briefly press .

???Each time the button is pressed briefly during playback, the previous or next chapter, track, or directory (file) will be played.

???You cannot skip chapters consecutively.

Something like you

Back for good

Love of my life

More than words

I need you

My love

Uptown girl

TITLE 01/05 CHAPTER 004/040

Something like you

Back for good

Love of my life

More than words

I need you

My love

Uptown girl

???During fast playback of a CD or MP3-CD, sound is heard only at 2x speed, and not at 4x, 8x, and 32x speeds.

???No sound is heard during slow playback and step motion playback.

OPERATION

To Select a Repeat Playback Mode in the Disc Information Screen

4 Press ENTER button.

* For MP3 and JPEG discs, you cannot select Repeat Play from the information display screen.

Repeat Playback Options

???CHAPTER : Repeatedly plays the selected chapter.

???TITLE : Repeatedly plays the selected title.

???GROUP : Repeatedly plays the selected group.

???RANDOM : Plays tracks in random order.

(A track that has already been played may be played again.)

???TRACK : Repeatedly plays the selected track.

???DIR : Repeatedly plays all tracks in the selected folder.

???DISC : Repeatedly plays the entire disc.

???OFF : Cancels Repeat Playback.

OPERATION

DVD CD

1 Press INFO button twice.

??? For a CD, press INFO button once.

Press Cursor ,

3 buttons to select ???A-??? and then press ENTER button at the beginning of the segment.

???When ENTER button is pressed, the selected position will be stored in memory.

A -

A -?

REPEAT : A???

Press Cursor 2 button to move to

REPEAT PLAYBACK () display.

Press ENTER 4 button at the end

of the segment.

???The specified segment will be played repeatedly.

A - B

REPEAT : A???B

Zoom (Screen Enlarge) Function

want to enlarge.

SELECT ZOOM POSITION

Press EZ VIEW button.

???Each time the button is pressed, the zoom function will switch between On and Off.

???When a movie is played in Widescreen format, black bars at the top and bottom of the TV screen can be removed by pressing the EZ VIEW button.

DVD

3 Press ENTER

button.

???Each time the button is pressed, the zoom level changes as follows:

Bonus Group DVD-

AUDIO

Some DVD-Audio discs have an extra ???bonus??? group that requires a 4-digit key number to access. See the disc packaging for details and the-key number.

When you play a DVD-Audio disc that has a bonus group, the key number input screen appears automatically.

BONUS GROUP

KEY NUMBER :

???If you eject the disc, switch the power off, or unplug the player, you will need to re-enter the key number.

OPERATION

1Press INFO button twice.

Press Cursor , 2 buttons or numeric

buttons to select the desired audio language.

???Depending on the number of languages on a DVD disc, a different audio language (ENGLISH, SPANISH, FRENCH, etc.) is selected each time the button is pressed.

SP 2/3

FR 3/3

SP 02/ 03

FR 03/ 03

OFF / 03

???Depending on the disc, the Subtitle and Audio Language functions may not work.

Press Cursor, buttons

1Press INFO button. 2 or numeric buttons to select the desired title/track and then

press ENTER button.

Moving to a Chapter

Press Cursor , 3 buttons to move to

Chapter ( ) display.

Moving to a Specific Time

Press the numeric 6 buttons to select the

desired time and then press ENTER button.

OPERATION

MP3 JPEG

Press the numeric buttons.

???The selected file will be played.

???An MP3 or JPEG disc cannot be moved from the disc information screen.

???When playing an MP3 or JPEG disc, you cannot use , to move a folder.

To move a folder, press (Stop) and then press , .

???You can press on the remote control to move directly to the desired title, chapter, or track.

???Depending on the disc, you may not be able to move to the selected title or time.

40

1 In Stop mode, press MENU button.

Press Cursor , 2 buttons to move to

???DISC MENU??? and then press ENTER button.

???When you select the disc menu that is not supported by the disc, the "This menu is not supported" message appears on the screen.

WIDE

4:3LB

(4:3 Letterbox)

4:3PS

(4:3 Pan&Scan)

:Select this to view a 16:9 picture in the full-screen mode on your wide screen TV.

???You can enjoy the wide screen aspect.

:Select this to play a 16:9 picture in the letter box mode on a conventional TV.

???Black bars will appear at the top and bottom of the screen.

:Select this to play a 16:9 picture in the pan & scan mode on a conventional TV.

???You can see the central portion of the screen only (with the sides of the 16:9 picture cut off).

SETUP

Press Cursor 3 button to move to

???PARENTAL??? and then press ENTER button.

Press Cursor , button 4 to select the desired rating

level and then press ENTER button.

???If you have selected Level 6, you cannot view DVDs with Level 7 or higher.

???The higher the level, the closer the content is to violent or adult material.

Enter the password 5 and then press

ENTER button.

???The password is set to "7890" by default.

???Once the setup is complete, you will be taken to the previous screen.

During playback, press

1PLAY/PAUSE button when an image you like appears.

PAUSE

The power will turn off 3 and then back on and the disc tray will open

automatically.

???The selected wallpaper will be displayed.

??????COPY LOGO DATA??? will be displayed on the TV screen.

COPY LOGO DATA

Press OPEN/ 4 CLOSE to close the disc tray.

???You can repeat Steps 1 and 2 to set up to 3 wallpapers.

Select this to set the Samsung Logo image as your wallpaper.

Select this to set the desired image as your wallpaper.

Press RETURN button to return to the previous level.

Press MENU button to exit the setup screen.

SETUP

Press the MENU 1 button while the disc tray is open.

Press Cursor 3 button to move to

???DVD TYPE??? and then press ENTER button.

Press Cursor 2 button to move to ???Setup??? and then

press ENTER button.

Press Cursor , 4 button to move to

???DVD VIDEO??? and then press ENTER button.

???Set steps 1 ~ 4 again if you want to switch to DVD AUDIO Play mode.

???

???

DVD VIDEO : set to play the DVD video contents contained in DVD audio disc.

DVD AUDIO : set to play the default DVD audio.

???DVD Play mode is set to DVD Audio as factory default setting.

Press RETURN button to return to the previous level.

Press Cursor , buttons 3to move to ???AV-SYNC??? and

then press ENTER button.

??? AV-SYNC screen appears.

Press Cursor , buttons 4 to select the Delay Time of

AV-SYNC and then press the ENTER button.

???You can set the audio delay time between 0 ms and 300 ms. Set it to the optimal status.

SETUP

In Stop mode, 1 press MENU

button.

In the Speaker 3 Setup, press the

ENTER button again.

Press Cursor 2 button to move to ???Audio??? and then

press ENTER button.

Press Cursor , ,

, buttons to move 4 to the desired

speaker and then press ENTER button.

???For C, LS, and RS, each time the button is pressed, the mode switches alternately as follows: SMALL ??? NONE.

???For L and R, the mode is set to SMALL.

Press RETURN button to return to the previous level.

Press MENU button to exit the setup screen.

SETUP

Alternate method: press the TEST TONE button on the remote.

Press TEST TONE button.

???Test tone will be produced as follows: When playing a DVD or CD, this will work only in Stop mode.

???Use this function to check that each speaker is correctly connected and that there is no problem.

To end the test tone,

press TEST TONE button again.

Multi-Channel Pro Logic Mode

Start

56

Press Cursor button 3to move to ???DELAY

TIME??? and then press ENTER button.

Press Cursor , , 4 , buttons to move

to the desired speaker and then press ENTER button.

Press Cursor , 5 totime.set the Delay

???You can set the delay time for C between 00 and 05mSEC and for LS and RS between 00 and 15mSEC.

Press RETURN button to return to the previous level.

Press MENU button to exit the setup screen.

SETUP

???Setting CENTER SPEAKER

If the distance of Dc is equal to or longer than the distance of Df in the figure, set the mode as 0ms. Otherwise, change the setting according to the table.

???Setting REAR (SURROUND) SPEAKERS

If the distance of Df is equal to the distance of Ds in the figure, set the mode as 0ms. Otherwise, change the setting according to the table.

Ideal CENTER

SPEAKER placement

Ideal

SURROUND

SPEAKER placement

It is desirable to place all speakers within this circle.

Df: The distance from FRONT SPEAKER

Dc: The distance from CENTER SPEAKER

Ds: The distance from SURROUND SPEAKER

58

Press Cursor button 3 to move to ???SOUND

EDIT??? and then press ENTER button.

Press Cursor , 4 buttons to select and

adjust the desired item. Press the , buttons to adjust the settings.

SETUP

Press Cursor 3 button to move to

???DRC??? and then press ENTER button.

4 Repeatedly press Cursor , to adjust the ???DRC???.

???Pressing the Cursor button increases the compression, and pressing the Cursor reduces it.

To Turn On or Off Sound Logo

When you turn on the power, the unit produces a sound logo after the disc reading to notify that the unit is optimized for playback.

1 Press and hold ASC button.

??? "S.LOGO ON" or "S.LOGO OFF" appears in the display.

2 Briefly press ASC button.

To Verify the Auto Sound Calibration

1 Press and hold ASC button twice.

??? "ASC CHECK" appears in the display.

2 Briefly press ASC button.

???Distance and level values specified for each channel will appear in the display.

Plug the auto sound calibration 1 microphone into the auto sound

calibration input jack.

??? The auto sound calibration setup takes about 2 minutes to complete.

A bell sounds and the setup finishes.

When the message "REMOVE MIC" 5 appears in the display, unplug the auto

sound calibration microphone.

To cancel the auto sound calibration setup, press ASC button.

??? The tone output stops, "CANCEL ASC" appears in the display followed by "REMOVE MIC", and the setup is cancelled.

To listen in the auto sound calibration mode, briefly press ASC button.

(If you set the auto sound calibration in the order from 1 to 4 above for the first time)

???The selection alternates between ASC ON and ASC OFF in the display.

???If you select "ASC ON", you will hear sound in the auto sound calibration mode.

If you select "ASC OFF", you will hear sound in the mode set in the audio setting of the setup screen.

SETUP

You can reproduce a 2-channel sound source, such as CD, and radio broadcast, in 5.1-channel

surround sound.

If you press the MUSIC button when listening to a 2-channel sound source, it will be reproduced in 5.1-channel surround sound so that you can enjoy a dynamic sound with a sense of presence.

You can select from 3 different modes of sound field for movies.

Press SUPER5.1

5.1 and SUPER OFF.

???Select "SUPER 5.1" to play 2-channel

sound in 5.1 channels.

Press MOVIE button.

???Each time the button is pressed, the selection changes as follows:

Plug the

1 headphones into the headphone jack.

???You can purchase headphones from most Electronics stores.

???Each time the button is pressed, the selection alternates between

VIRTUAL ON and VIRTUAL OFF.

???

???

VIRTUAL ON: Select to enjoy a 5.1-channel surround sound that gives the feeling of being in a baseball park or concert hall.

VIRTUAL OFF: Select to listen to a standard 2-channel stereo sound.

Press PL II MODE

1 button to select ???MUSIC??? mode.

Press PL II EFFECT button 3 and then press Cursor ,

buttons to select the mode.

??? You can select between 0 and 7.

Press PL II EFFECT button 2 and then press Cursor ,

buttons to select the mode.

??? You can select either 0 or 1.

Press PL II EFFECT button 4 and then press Cursor ,

buttons to select the mode.

??? You can select between 0 and 6.

SETUP

???The selection toggles back and forth between "FM ??? AM" each time the TUNER(BAND) button is pressed.

Automatic Tuning 1

Automatic Tuning 2

Manual Tuning

When is pressed, a preset broadcast station is selected.

Press and hold to automatically search for active broadcasting stations.

Briefly press to increase or decrease the frequency incrementally.

Main Unit

Press the Function 1 button to select the

desired band (FM, AM).

2 Select a broadcast station.

Automatic Tuning 1 Press the STOP ()

button to select PRESET and then press button to select the preset station.

Automatic Tuning 2 Press the STOP () button

to select "MANUAL" and then press and hold button to automatically search the band.

Manual Tuning Press STOP () to select MANUAL and then briefly

press to tune in to a lower or higher frequency.

???

69 ???

Each time the button is pressed, the sound switches between "STEREO" and "MONO". In a poor reception area, select MONO for a clear, interference-free broadcast.

Press the

1TUNER(BAND) button and select the FM band.

???Each time the button is pressed, the band switches between "FM ??? AM".

2 Press to select "89.10".

???Refer to Step 2 on page 69 to automatically or manually tune in to a station.

3 Press the TUNER

MEMORY button.

??? ???PRGM??? flashes in the display.

??????PRGM??? disappears from the display and the station is stored in memory.

OPERATION RADIO

Mute Function

This is useful when answering the door or a telephone call.

Press MUTE button.

??????MUTE ON??? appears in the display.

???To restore the sound, press the button again to select ???MUTE OFF???.

kHz

MHz

MISCELLANEOUS

When operating a TV with the remote control

???If the code matches the TV's code, the TV will be turned off.

???If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.

Example: For a Samsung TV

While holding down POWER, use the number buttons to enter 00, 01, 02, 03, 04, and 05.

Pont the remote control toward the TV and press 5 POWER. If the TV turns off or on, the setting is

complete.

???You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9).

TV Brand Code List

MISCELLANEOUS

MISCELLANEOUS

???Do not allow the discs to become contaminated with dirt.

???Do not load cracked or scratched discs.

SAMSUNG DVD PLAYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year Parts and Labor*

(*90 Days Parts and Labor for Commercial Use)

This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the service center is the responsibility of the purchaser.

SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.

SAMSUNG???s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an ???AS IS??? basis. NonSAMSUNG- manufacturers, suppliers, publishers, and service providers may provide their own warranties.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS

WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING

ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER

BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO

USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN

AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT

LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND

PURCHASER???S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS

PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT

EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR

EXCLUSIVE REMEDY.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

To obtain warranty hardware service, please contact SAMSUNG at:

SAMSUNG CUSTOMER CARE CENTER

400 Valley Road, Suite 201, Mt. Arlington, NJ 07856, Tel: 973-601-6000, Fax: 973-601-6001

MISCELLANEOUS

1-800-SAMSUNG (1-800-726-7864) and www.SAMSUNGUSA.com

80