CAUTION/WARNINGS USED

OTHER SIGNS USED

Represents something you must NOT do.

WARNING

Indicates that a danger of death or serious injury exists.

Represents something you must NOT disassemble.

Represents something you must NOT touch.

Represents something you must follow.

WARNINGS

Do not plug several appliances into the same multiple power board.

??? This could cause overheating and the risk of fire.

Make sure that the power plug is not squashed or damaged by the back of the refrigerator .

???A damaged power plug may overheat and cause fire.

Do not directly spray water inside or outside the refrigerator/ freezer. .

??? There is a risk of electric shock.

Do not use aerosols near the refrigerator .

??? There is a risk of explosion or fire.

Do not bend the power cord excessively or place heavey articles on it .

???This constitutes a fire hazard. If the power cord is damaged, have it replaced immediately by the man- ufacturer or its service agent.

Do not insert the power plug with wet hands.

??? You may receive an electric shock.

Do not put a container filled with water on the refrigerator.

??? If spilled, there is a risk of fire or electric shock.

Do not install the refrigerator in a damp place or a place where it may come in contact with water.

???Deteriorated insulation electrical parts may cause electric shock or fire.

Indicates that you must disconnect the power plug from the socket.

Represents a ground is needed to prevent electric shock.

It is recommended that this sentence be handled by service man.

Do not store volatile or flammable substances in the refrigerator.

???The storage of benzene, thinner, alcohol, ether, LP gas and other such products may cause explosions.

Do not disassemble or repair the refrigerator by yourself.

???You run the risk of causing a fire, malfunctions and/or personal injury.

Pull the power plug out of the socket before changing the interior light of the refrigerator.

??? Otherwise, there is a risk of electric shock.

If you wish to dispose of the refrigerator / freezer throw it away after first removing the doors and seals.

???Do so in a way, that is not possible for a child to remain trapped inside.

The refrigerator must be grounded.

??? You must ground the refrigerator to prevent any power leakages or electric shocks caused by cur- rent leakage from the refrigerator.

Never use gas pipes, telephone lines or other potential lightening rods as ground.

???Improper use of the ground plug can result in elec- tric shock.

SAFETY WARNING

CAUTIONS

Do not overfill the refrigerator with food.

???When you open the door, an item may fall out and cause personal injury or material damage.

Do not put bottles or glass containers in the freezer .

???When the contents freeze, the glass may break and cause personal injury.

If the wall socket is loose, do not insert the power plug.

??? There is a risk of electric shock or fire.

Do not disconnect the power cord by pulling on it.

???Damage to the cord may cause a short-circuit, fire and/or electric shock.

???If the power cord is damaged, it must be replaced by the manufacturer, a certified service agent or qualified service personnel.

Do not store articles on the top of the appliance .

???When you open or close the door, the articles may fall and cause personal injury and/or material dam- age.

Do not store pharmaceuticals products, scientif- ic materials or temperature-sensitive products in the refrigerator.

???Products that require strict temperature controls must not be stored in the refrigerator.

Do not let children hang on the door. If not, a serious injury may occur.

If you smell pharmaceuticals or smoke, pull out the power plug immediately and contact your SAMSUNG Electronics service center.

Do not touch the inside walls of the freezer or products stored in the freezer with wet hands.

??? This may cause frostbite.

Do not insert your hands into the bottom area under the appliance.

??? Any sharp edges may cause personal injury.

Never put fingers or other objects into the dispenser hole and ice chute. It may cause per- sonal injury or material damage

SAFETY WARNING SIGNS

Do not use a wet or damp cloth when cleaning the plug. Remove any foreign matter or dust from the power plug pins.

???Otherwise there is a risk of fire.

???If the refrigerator is disconnected from the power supply, you should wait for at least five minutes before plugging it back.

If the refrigerator is not to be used for a long period of time, pull out the power plug.

???Deterioration in the insulation may cause fire.

???Contains fluorinated greenhouse gases covered by the Kyoto Protocol.

???Hermetically sealed system.

???Do not vent gases into the atmosphere.

???Refrigerant type: R-134a

???Quantity: 0.22 Kg

???Global Warming Potential (GWP) = 1300

Place the refigerator in an appropriate loca- tion with reasonable clearance between the wall and the refigerator.

(refer to installation instructions in this man- nal)

When the refrigerator is plugged in, the interior light should come on when you open the doors.

Set the temperature control to the coldest temperature and wait for an hour. The freezer should get slightly chilled and the motor should run smoothly.

Once the refrigerator temperature is suffi- ciently low, you can store food in the refrigerator. After starting the refrigerator, it takes a few hours to reach the appropriate temperature.

CONTROL PANEL

Basic Model

Dispenser Model (Child Lock)

Dispenser Model (Moisture Control)

OPERATING INSTRUCTIONS

FREEZER TEMP. BUTTON

To set the freezer temperature, press the button repeatedly to change the set temperature in sequence between

-14??C and -25??C

FRIDGE TEMP. BUTTON

To set the fridge temperature, press the button repeatedly to change the set temperature in sequence between 7??C and 1??C.

POWER FREEZE BUTTON

Speeds up the freezing process in the freeze.

ICE TYPE BUTTON

Use this button to choose Cubed or Crushed Ice or Ice off.

POWER COOL BUTTON

Speeds up the cooling process in the refrigerator

MOISTURE CONTROL BUTTON

Initially the light of moisture control but- ton is on. If the moisture in the dis- penser or Beverage StationTM is found, press this button. So the light will be on, and eliminate the moisture.

CHILD LOCK BUTTON

When this button is pressed for 3 sec., the Power Freeze, Power Cool, Freeze Temp. Fridge Temp. are locked and can not be modified. The Water and Ice dispenser are not locked as to allow for usage.

Freezer Temp. indicates the current freezer temperature. Fridge Temp. indicates the current refrigerator temperature.

Quick Cool, Thaw, and Select show the status of the CoolSelect ZoneTMDrawer

OPERATING INSTRUCTIONS

Power Freeze

Power Cool

Deodorizer

???This light is on when you press the Power Freeze button.

Press this button to quickly return the freezer to the set temperature.

???If you need much ice, you can get ice faster.

???Press the button again to cancel the Power Freezer mode.

???This light is on when you press the Power Cool button.

Press the button to quickly return the refrigerator to the set temperature.

???Press the button again to cancel the Power Cool mode.

???This light indicates the recyclable deodorizer is in operation.

???Recycle the honeycomb cartridge once or twice a year (see ???Cleaning the Accessories??? section)

Ice Dispenser

The ice maker produces 10 cubes at once and about 120 cubes a day automatically. This quantity may be influenced by factors such as the freezer temperature, the Power Freeze function and the number of door openings. When your refrigerator is plugged in, the Cubed Ice mode is auto- matically selected .

Press the IceType button to select the type of ice:

??? Cubed Ice

Water Dispenser

The capacity of the water tank is approximately 1.2 .

Cold Water

???Push the water dispenser lever with a cup.

???If you have just installed the refrigerator, throw away the first six glassfuls of water to flush out impurities in the water supply system.

Push the ice dispenser lever with a cup.

???Place a cup in line with the dispenser lever the dispenser to prevent ice from jumping out.

Push

WARNING

Push

If you have a long vacation or business trip and won???t use the water or ice dispensers, close the water valve. Otherwise, water may occur leakage.

Never put fingers or any other objects in the dispenser opening.

It may cause injury.

Basic Model

OPERATING INSTRUCTIONS

Dispenser Model

FOOD STORAGE GUIDE

CHILLED FOOD STORAGE IN REFRIGERATOR

Tempered Spill Proof Glass Shelf

??? Can be used to store all types of chilled food.

??? Safe and hard to break resistant.

??? Circular marks on the glass surface are a normal phenomenon.

Chilled Bin or CoolSelect ZoneTM Drawer (optional)

???Helps to preserve the taste of food and prolongs its freshness. Use to store cheese, meat, poultry, fish or any other foods used quickly.

Fruit & Vegetable Drawer (Upper and Lower)

??? Is used to store fruits and vegetables.

???This drawer is airtight. Optimized humidity control design helps to pre- serve the freshness of the stored vegetables and fruits.

Without drawers, the fruit & vegetable can be stored.

NOTE

Dairy Compartment

??? Can be used to store butter or margarine.

Gallon Door Bins

??? Can be used to store foods in small packages, such as milk and yogurt.

Beverage Station (optional)

??? Can be used to store the frequently used items, such as canned bev- erages and snacks and allows access to these items without opening the refrigerator door.

Bottles should be stored tightly together so that they do not fall out.

CAUTION

Egg Container

??? Put eggs in the container and place them on the shelf.

Wine Shelf (optional)

??? Place your wine bottle on the shelf to maintain their taste.

OPERATING INSTRUCTIONS

???

???

???

When ???Soft Freeze??? is chosen, the temperature on the

digtal panel displays -5oC regardless of the set tempera- ture of the refrigerator.

???Soft-Freeze??? temperature helps keep meats and fishes

fresh longer. Can cut meat easily without drips.

???

???

When ???Chill??? is chosen, the temperature of the CoolSe- lect ZoneTM Drawer is kept at -1oC regardless of the set refrigerator temperature.

???Chill??? temperature helps keep meat or fish fresh longer.

???

???

When ???Cool??? is chosen, the temperature will be the same as the set temperature of the refrigerator. The digital panel shows the same temperature as that of the display panel.

The CoolSelect ZoneTM Drawer allows extra refrigerator space.

CoolSelect ZoneTM Drawer GUIDE

???Quick Cool??? button

??? You can use the Quick Cool feature with the CoolSelect ZoneTM.

??? ???Quick Cool??? allows 1~3 canned beverages to cool within 60 min.

??? To cancel this option, press the ???Quick Cool??? button again. CoolSelect ZoneTM returns to the previous temperature.

??? When ???Quick Cool??? ends, it returns to the ???Cool??? temperature set- ting.

Depending on the beverages, the cool-down time may vary.

NOTE

??? For ???Quick Cool??? option, food stored in the CoolSelect ZoneTM Drawer should be removed.

WARNING

???Thaw??? button

??? Drips loss and quality deterioration of meats reduces the fresh- ness of foods.

??? After ???Thaw??? is selected, warm and cold air is alternately sup- plied into the CoolSelect ZoneTM Drawer .

??? Depending on the weight of meat, thawing time can be selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs sequentially.

??? When ???Thaw??? ends, CoolSelect ZoneTM display returns to ???chill??? condition.

??? When ???Thaw??? ends, there are no juice in the meats and they are half-freezed condition so it is easy to cut them for cooking.

??? To cancel this option, press any button except ???Thaw???.

??? The approximate thawing time of meat and fish are shown below. (Based on 1inch thickness)

Depending on the size and thickness of meat and fish, the thawing time may vary.

Ex) The total thawing time for 400g frozen beef and 600g frozen chicken will be 10 hours.

??? With the ???Thaw??? option, food stored in the CoolSelect ZoneTM Drawer should be removed.

WARNING

OPERATING INSTRUCTIONS

Glass shelf

???Pull the shelf out as far as it goes. Then lift it up and remove it.

Door bin

???Hold the door bin with both hands and then lift it up.

Plastic drawer

???Remove the drawer by pulling it out and lifting it up slightly.

Ice maker bucket (optional)

??? Remove the bucket by lifting up and pulling out.

Front leg cover

??? Open the freezer and refriger- ator doors, remove three screws and detach the cover.

??? To reassemble the cover leg front, put it back to original position and tighten the three screws.

BEVERAGE STATIONTM (optional)

To open the Beverage StationTM, hold the Beverage StationTM door handle and pull it downward.

???The door of the Beverage StationTM should never be removed. The Beverage StationTM cannot function if its door is missing.

???When closing the Beverage StationTM door, be careful not to put your hands or fingers around the door frame

where they can be caught or injured.

WARNING ??? When you use the open door as a tray, do not place heavy objects on it. Do not allow children to hang on the door because there is a risk of personal injury or material damage.

??? When you open the beverage stationTM door, be careful not to hit children head.

CLEANING THE ACCESSORIES

Interior

??? Clean the accessories with a mild detergent, then wipe out with a dry cloth.

??? After washing the accessories, make sure that they are dry before using them again.

Exterior

??? Wipe the digital panel and display panel with a clean cloth.

??? The doors and handles should be cleaned with a mild detergent and cloth. Dry them with a clean cloth.

??? The exterior part of refrigerator should be polished once or twice a year.

Rear

??? Use a vacuum cleaner to remove dust once or twice a year.

Ice and water dispenser (optional)

??? Use a damp cloth to clean the ice and water dispenser. Then wipe it out with a dry cloth.

??? To keep drainage grid dry, do not touch ice and water dispenser.

Beverage StationTM (optional)

??? Use a damp cloth to clean the Beverage StationTM. Then wipe it out with a dry cloth.

Rubber door seals

??? If the rubber door seals are dirty, the door will not close properly, The refrigerator will not be able to function efficiently. Clean the doors with a mild detergent and damp cloth. Wipe with a dry cloth.

??? Do not spray the refrigerator with water. It may cause a death by an electric shock.

??? Do not clean it with benzene, thinner or car detergent. It may cause a fire.

WARNING

15

OPERATING INSTRUCTIONS

Pull out the screw cap ??? and remove the screw.

Lower (optional)

Pull out the screw cap ??? and remove the screw.

Push the lamp cover in the direction of the arrows.

Take the lamp cover out in the direction of the arrows.

After changing the bulb, reattach the light cover and screw it in again.

After changing the bulb, reattach the light cover and screw it again.

To replace freezer and refrigerator light bulbs (Bulb size E14), please contact SAMSUNG dealer.

NOTE

INTERIOR LIGHT IN THE FREEZER (Basic Model)

WATER FILTER

The water ???Filter Indicator??? light

??? ???Filter Indicator??? light lets you know when it is time change your water filter cartridge. The light

will change from green to orange. This tells you that it is almost time to change the current cartridge. It is recommended that you replace the cartridge when the light changes to red.

(see ???Install the water filter??? section for more information)

Using the dispenser without the water filter

???You can not use the water and ice dispenser without a water filter cartridge because of the water line block at the water supply.

Ordering replacement filters

??? To order more water filter cartridges, contact your authorized Samsung dealer.

DOORS

The refrigerator doors have a special door opening and closing feature to make sure that the doors close all the way and are securely sealed.

When opening the door, it will only open so far. After reaching a certain point, it will remain open.

When the door is partially open, it will close automatically .

OPERATING INSTRUCTIONS

SCREW

Separating the water supply line from the refrigerator (Optional)

1)Remove the screw from clamp ( a ).

2)Remove the water tube by pressing the coupler (???) and pulling the water tube (???) away.

Do not cut the water tube but separate it from the coupler.

WARNING

19

INSTALLATION INSTRUCTIONS

3)Remove the door from the lower hinge (???) by carefully lifting the door (???).

4)Remove the lower hinge (???) from the bracket lower hinge (???) by lifting the lower hinge (???) in the direction of the arrow.

REMOVING THE REFRIGERATOR DOORS

Removing the Refrigerator Door

1)With the door closed, remove the upper hinge cover (???) using a screwdriver, and then discon- nect the wires (???).

2)Remove hinge screws (???) and ground screw (???) counter-clockwise, and take off the upper hinge (???) in the direction of the arrow (???). Take care when removing the door to ensure that it

does not fall on you.

INSTALLATION INSTRUCTIONS

1)Insert the lower hinge (???) in the bracket lower hinge (???).

2) Reattach the freezer door by inserting the hose (???) in the lower side of the door into the hole in the lower hinge (???) and pulling the hose down.

REATTACHING THE REFRIGERATOR DOORS

Reattaching the Refrigerator Door

3)Insert the upper hinge shaft (???) into the hole (???). After levelling between the upper hinge hole (???) and the hole of the cabinet (???). Reattach hinge screws (???) and screw (???) in the clockwise direc- tion.

INSTALLATION INSTRUCTIONS

ADJUSTING THE CLEARANCE BETWEEN THE DOORS

Please level the refrigerator first.

The doors will be uneven if the refrigerator is not level.

Case 1) Freezer door is lower than that of the refrigerator

DIFFERANCE OF HEIGHT

Insert a straight screwdriver (-) (???) into a slot of the control lever (???), turn it clockwise and level the refrigerator.

??? DRIVER(-)

Case 2) Freezer door is higher than that of the refrigerator

DIFFERANCE OF HEIGHT

??? CONTROL LEVER

Insert a straight screwdriver (-) (???) into a slot of the control lever (???), turn it clockwise and level

the refrigerator.

??? DRIVER(-)

??? CONTROL LEVER

Do not make small adjustment by turning the control lever, Please refer to the next page.

NOTE

INSTALLATION INSTRUCTIONS

If the door of the freezer is lower than that of the refrigerator.

If the door of freezer is higher than that of the refrigerator.

CHECKING THE WATER DISPENSER LINE (Optional)

1)In order to operate the ice maker properly, water pressure of 1.4 ~ 10 kgf/cm2 is required. In this range a 100 cc paper cup can be filled in 10 seconds.

2)The water filter removes particles. It does not sterilize or destroy any micro-organisms.

3)If the refrigerator is installed in an area with low water pressure (below 1.4kgf/cm2), you should install a booster pump to compensate for the low pressure.

4)Ensure the water storage tank inside the refrigerator is preperly filled initially. Push the water dis penser lever until the water runs from the outlet.

A universal water supply kit is available at extra cost from your dealer. The refrigerator manufac- NOTE turer recommends using a water supply kit containing copper tubing.

Checking the Parts

Purifier

(Interior model)

Sealing tape

Clip A x 8EA

Tapping screw x 12EA

Purifier lock

(Exterior model)

INSTALLATION INSTRUCTIONS

- Shut off the main water supply line and turn the Ice maker to the off position.

- Locate the nearest cold drinking water line.

- Follow the instructions in the ice maker installation kit.

1.Cold Water line

2.Pipe Clamp. 3.Copper (or Plastic) line 4.Compression Nut 5.Compression Sleeve 6.Shut Off Valve 7.Packing Nut.

-Slip the compression nut and plastic ferrule through the plastic tube.

-After inserting the sleeve, tighten the compres- sion nut onto 1/4??? compression fitting(union).

Do not overtighten the compression

NOTE nut.

- Slip the compression ferrule and nut on cop- per (or plastic) tubing as shown.

Tighten the comperssion nut onto the com- pression fitting(union).

- Turn water on and check for any leakege.

Compression Nut

Ferrule

Sleeve

Compression fitting

Ferrule

Compression Nut

Connect the water pipe with coupler and tap.

-Close the main water tap.

-Connect coupler ???A??? to the tap.

-Every join should be protected with sealing tape.

WARRANTY INFORMATION

This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty. Follow these instructions carefully to minimise the risk of expensive water damage.

CAUTION

The water line must be connect- ed to the cold water pipe.

If it is connected to the hot water pipe, it may cause the puri- fier to malfunction.

COUPLER ???A???

the right couplers fittings.

TAP

INSTALLING THE WATER DISPENSER LINE

Connect the water line to the refrigerator.

CONNECTION NUT

- Remove the compressor cover of the refrigerator.

- Connect the water line to the valve, as shown in the figure. - When connected, check if there is any leakage.

If any, repeat the connection.

- Reattach the compressor cover of the refrigerator.

COMPRESSOR COVER OF

REFRIGERATOR

Secure the water line.

- Using clip ???A???, fix the water line to the wallor (the back of refrigerator).

CLIP A

- When the water line is secure, make sure whether the water line is not excessively bent, pinched or squashed.

WATER LINE

Complete the installation of the water supply line.

-Power on the refrigerator and press the lever on the right of the

dispenser until water runs out through the water line and all air has been empty.

-At this time, check for any possible leakages at the join point in the water line. After securing the water line, move the refrigerator to the required location. Once the refrigerator is in position, do not move possibly.

Install the water filter.

- As shown, separate the fixed cap in the refrigerator by rotating it counterclockwise.

Remove the water filter from the box and put a month indicator sticker on the filter as shown.

- Write the month you installed the filter on the label. EX) If the water filter was installed in March, put ???MAR???

-Remove the protective cap then position and insert the filter as shown,

-Slowly turn the water filter clockwise 90?? to align the indication mark on the

cover, locking the filter in postion. Do not overtighten.

COVER FILTER

SEPARATION

OF RED CAP

INSTALLATION INSTRUCTIONS

STICKER

ALIGN THE INDICATION MARK

WITH LOCK POSITION.

the right couplers fittings.

TAP

-Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap.

-If you wish to reassemble the water inlet and outlet sides of the purifier during purifi- er installation, see the reference illustra- tion.

LINE

OUTLET

PURIFIER

WATER

COUPLER

WATER INLET SIDE

OF PURIFIER

-Open the main water tap to check whether water is running through the water tube on the water inlet side of the purifier.

-If water does not come out through the line, check whether the tap is open.

-Leave the tap open until clean water is running out and any residual matter that built up during manufacturing has been removed.

OUTLET SIDE

OF PURIFIER

PURIFIER

WATER LINE

WATER

- Fix the purifier in position, as shown in the figure

PURIFIER

on the right.

TIGHTENING

BAND

Connect the water line to the refrigerator.

WATER LINE

- Remove the compressor cover of the refrigerator.

- Connect the water line to the valve, as shown in the fig- ure.

- When connected, check if there is any leakage. If any, repeat the connection.

- Reattach the compressor cover of the refrigerator.

PURIFIER

LOCK STA-

TIONS

CONNECTION NUT

COMPRESSOR COVER OF

REFRIGERATOR

INSTALLATION INSTRUCTIONS

Secure the water line.

-Using clip ???A???, fix the water line to the wallor (the back of refrigerator).

-When the water line is secure, make sure whether the water line is not excessively bent, pinched or squashed.

CLIP A

WATER LINE

2)When you press the test button, the ice cube container is filled with water from the water supply tap.

Check the amount of water (see the illustration below). If the water level is too low,

the ice cubes will be small.

This is not a problem with the ice maker but of the water pressure in the pipe, and occurs frequently. When this problem occurs, contact

the dealer service center to check the amount of water supplied.

TEST BUTTON

TOO HIGH

OPTIMUM

LEVEL

TOO LOW

The refrigerator does not work at all or it does not chill sufficiently

???Check that the power plug is properly connected.

???Is the temperature control on the display panel set to the correct temperature? Try seting it to a lower tem- perature.

???Is the refrigerator in direct sunlight or located near a heat source?

???Is the back of the refrigerator too close to the wall?

The food in the refrigerator is frozen

???Is the temperature control on the display panel set to the correct temperature? Try seting it to a warmer temperature.

???Is the temperature in the room too low?

???Did you store the food with a high water content in the coldest part of the refrigerator.

You can hear unusual noise or sounds

???Check that the floor is levelled and stable.

???Is the back of the refrigerator too near to the wall?

???Was anything dropped behind or under the refrigera- tor?

???A ???ticking??? sound may be heard from inside the refrig- erator, but this is normal. This occurs because vari- ous accessories are contracted or expanded.

The front corners and sides of the cabinet are hot; condensation occurs.

???Anti-condensators are installed in the front corners of the refrigerator to prevent condensation.

???Condensation can occur when you leave the door open for a long time.

Ice is not dispensed

???Did you stop the ice making function?

???Is there any ice in the ice storage unit?

???Is the water line connected and the shut-off valve open?

???Is the freezer temperature too warm? (Set the temperature lower)

???Did you wait for 12 hours after installation of the water supply line before making ice?

You can hear water bubbling in the refrigerator

???The bubbling comes from the refrigerant circulating in the refrigerator and is normal.

There is a bad smell in the refrigerator

???Wrap food with a strong smell so that it is airtight. Throw away any rotten food.

Frost forms on the wall of the freezer

???Is the air vent blocked?

???Allow sufficient space between the foods stored for efficient air circulation.

???Is the door closed properly?

No water is supplied

???Is the water line connected and the shut-off valve open?

???Is the water supply line crushed?

???Is the water tank frozen because the refrigerator tem- perature is too low? Select a warmer setting on the display panel.

INSTALLATION INSTRUCTIONS