[ SALES NETWORK ]

B W CCD CAMERA

INSTRUCTION MANUAL

BW-4302 SERIES

??SAMSUNG TECHWIN CO., LTD

OPTICS & DIGITAL IMAGING DIV.

145-3, SANGDAEWON 1-DONG, JUNGWON-GU,

SUNGNAM, KYUNGKI-DO, KOREA 462-121

TEL : 82 - 031-740 - 8137~41

FAX: 82 - 031- 740 - 8145

??SAMSUNG OPTO-ELECTRONICS AMERICA INC.

40 SEAVIEW DIRVE, SECAUCUS N.J 07094, U.S.A.

TEL : 209-902-0347

FAX : 201-902-9342

SAMSUNG CCD CAMERA

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

4 B W CCD CAMERA

WARNING- TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE.

INFORMATION -This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the manufacturer could void the user???s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use other than specified power source. Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

B W CCD CAMERA 5

Features

Automatic Backlight Compensation

The backlight compensation technology allows the camera to find the best picture conditions in any environment and automatically gives a necessary light level compensation, so that you can always obtain the clear picture, the finest detail and perfect light contrast.

High Resolution

The horizontal resolution of 570 TV lines can be achieved by using a high density CCD

having effective 410,000 pixels, which provides clean, noiseless and reliable pictures.

Electronic Iris

Electronic iris shutter is automatically controlled at the speed of 1/60~1/100,000sec (EIA models), 1/50~1/100,000sec (CCIR models).

Video / DC Selection Switch

The camera accepts 2 types of auto lris lenses (DC type/Video type) and is set with Video/ DC selection switch.

SYNC. System

You can select INT(Internal Synchronization) mode or L. L(Linelock Synchronization) mode.

Precautions

It can cause malfunctions to occur.

Do not expose the camera to rain or spill beverage on it.

If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components.

It can damage the CCD.

Do not touch the front glass of the camera.

It is one of the most important parts of camera. Be careful not to be stained by fingerprint.

Do not disassemble the camera.

There are no user-serviceable parts inside it.

Notes: ???If the camera is exposed to spotlight or object reflecting the strong light, smear or blooming may occur.

???Please check the power whether it satisfies the normal specification before connecting the camera.

Getting to Know Your Camera

Getting to Know Your Camera

???C - Mount Lens Adapter

??? Glass Protecting Cap

??? Back Focus

Lock Screw

??? CS- Mount Lens Adapter

Tripod Mounting Hold

Used to install the camera on an optional tripod. The tripod must be equipped with the screw specified as shown below

1/4???-20 UNC (20 THREAD)

L : 4.5mm ??0.2 mm (ISO standard), or 0.197???(ASA standard)

L

You can remove and install this bracket on the top of the camera.

You must use the supplied screw or the equivalent

(within 5mm). If not, it can cause malfunction and demage inside the camera.

IRIS Mode

Selection Switch.

Video Out Jack

Auto Iris Lens Connector

SYNC Mode selection switch

Notes:There is no Sync selection switch on the rear of DC power type.

High Voltage type (4302CH)

IRIS lens plug

BLC Function select Switch

LEVEL Adjustment V.R

(Using DC Iris Lens Only!)

L-Wrench

Power Input Terminal

Notes: Each model has the different power source.

V.PHASE Adjustment V.R

Notes: There is no V.PHASE VR on the rear of DC power type.

Instruction

Manual

Controls and Adjustments

Glass Protecting Cap

Be sure to cap the lens mount when the lens is not mounted. Pull out the cap to remove.

C-Mount Lens Adapter

Used to mount a C-mount lens. Remove it to mount a CS-mount lens. Turn counterclockwise to remove.

CS-Mount Lens Adapter

Used to mount a CS-mount lens. C-mount lenses can be used when the C-mount adapter is attached, and CS-mount lenses can be used when it is removed.

Back Focus Lock Screw

Used to readjust backfocus of the camera. There are two backfocus lock screws. These must be loosened before the camera may be back focused. Loosen lock screw using the L-wrench to turn the CS-mount lens adapter, and tighten the lock screw after adjustment.

Tripod Mounting Hole

This screw hole is used to install the camera on a mount. The camera can be installed on a tripod or other camera mount either from the top or the bottom by using the 1/4??? - 20UNC threaded holes in the camera. For details, see page 11.

Video Out Jack

Connect to the video input connector of monitor. This jack outputs a composite video signal. Use a coaxial cable for connection.

Auto lris Lens Connector

Used to connect auto iris lens plug. Be sure to use video-drive auto iris lens that operates on DC 12V and requires 40 mA or less. For details, see page 18.

Controls and Adjustments

SYNC Mode Selection Switch

Used to choose INT or LL mode.

SYNC (Synchronization) Mode

INT(Internal) mode : The camera may be operated independently with its internal crystal control.

LL(Linelock) mode : It synchronizes the video signal between cameras using the frequency of the AC power supply without external synchronous generator.

Notes : The LL mode can be used in the areas of 60Hz(EIA models) and 50Hz(CCIR models).

There is no SYNC selection switch on the rear of DC power type.

V. PHASE Adjustment V. R

If camera is to be used in the LL mode, the vertical phase may require adjustment to synchronize the vertical phase of the camera with other camera in the system.

Make this adjustment when the vertical phase of the camera does not match with other cameras or systems. For correct adjustment, use a multi- channel oscilloscope. The V adjustment has been set at 180 degrees and can be readjusted in the range of 0 to 270 degrees.

Notes : This adjustment is necessary only when line lock sync operation is performed.

There is no V. PHASE V.R on the rear of the DC power type.

Power Input Terminal

Used to connect AC/DC power source. For details, see page 23.

Notes : Each model has the different power source, you must confirm appropriate power source of your camera.

Level Adjustment V. R (Using DC Iris Lens Only!)

Used to adjust video output level. When the brightness control of the monitor does not operate correctly, you can get the optimum picture by controlling the Video output level of camera.

Controls and Adjustments

Notes : This function is activated when being in the ESC mode.

BLC(Backlight Compensation) Function CENTER/FULL Switch

This switch improves an image that is darkened because of backlighting. This Function be possible only when the camera have a manual lens. When the lighting source is in the rear of object, the object might be seen some darkness. If you want to see object clearly, turn this switch Center or Full the following diagram:

IRIS Mode Selection Switch

Used to choose DC/VIDEO or ESC mode according to the type of your lens.

USING AUTO IRIS LENS

You can choose DC or VIDEO mode according to the type of the lens. In this case, electronic shutter is fixed in ???1/60??? sec(EIA models), ???1/50???sec(CCIR models).

MANUAL LENS

When manual lens is mounted, two modes are available.

In VIDEO or DC mode, electronic shutter is fixed in ???1/60??? sec(EIA models), ???1/50??? sec(CCIR models).

In ESC mode, electronic shutter is automatically controls the shutter speed from ???1/60??? to ???1/100,000??? sec(EIA models), ???1/50??? to ???1/100,000??? sec(CCIR models).

Notes : ESC (Electronic Shutter Control)mode : Electronically controls optimal shutter speed.

Connection

Lens

Lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts auto iris lens, both C- and CS-mount lens.

Notes:

If the lens is stained with fingerprint or something, the image quality might be poor.

It is recommended to use a high quality lens to improve the image quality under low illumination.

Installing Auto Iris Lens

1. Peel the end of lens cable outer cover approximately 8mm. (5/16inch)

approx.

8 mm(5/16inch)

2. Peel the end of the cable inner cover approximately 2mm. (1/16inch)

approx. 2 mm(1/16inch)

CONNECTION

3.Remove the cover from the connector pin supplied, and solder the lens cable to the connector pin as shown

below.

??? Video type :

4.Remove the protecting cap, and attach the lens into the camera by turning clockwise.

CONNECTION

5.Connect the lens plug to the auto iris connector on the rear of the camera.

6.Set the IRIS Mode selection switch to Video according to the type of the lens.

CONNECTION

Installing CS-Mount lens

1. Remove the protecting cap and C-mount adapter.

C-Mount Lens Adapter.

Glass Protecting Cap.

2. Attach the lens into the camera by turning clockwise.

CONNECTION

Connecting to Monitor

Connect the VIDEO out jack to the monitor video in jack.

CONNECTION

Connecting to Power

Each model has the different power source and the operation characteristics.

Make sure the power is supplied to the appropriate power terminals on the camera. Connect the power as referred on the following figures.

???As a connecting method varies according to instruments, refer to the manual supplied with the instrument.

???Connect the cable after power is turned off.

???Set the 75???/Hi-Z selection switch as shown below if you have intermediate device.

AC24V, 60Hz : BW-4302EA

AC24V, 50Hz : BW-4302CA

Intermediate

VIDEO

IN OUT

VIDEO

75 Hi-Z

IN OUT

AC230V , 50Hz : BW-4302CH

Notes:

Troubleshooting

If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician.

Specifications

Application of Council Directive(s)

Manufacturer's Name

Manufacturer's Address

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Beginning Serial NO.

Year of Manufacture

Conformance to

89/336/EEC

SAMSUNG TECHWIN CO., LTD

SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-120

Black & White CCD CAMERA

BW-4302CA/BW-4302CH

M1120001

2001

EN 60065

EN 55 013

EN 50 082-1