Q3
Q4
Q5
HDD does not be recognized in BIOS setup.
1First, confirm whether each cable was connected correctly.
2Confirm whether
3Confirm whether BIOS setup became correctly.
Even though the HDD recognized in BIOS setup, it does not be seen in Windows.
1Confirm whether did correctly partition and format.
2Partition can be created through the Fdisk or Installing OS according to OS's version.
I am looking for a Software & Firmware (mainly about drivers) but I found nothing.
Where I can find I want ?
We don't release any firmwares.
Because the product has been already optimized with its own configurations.
IDE (PATA & SATA) drive does not need any drivers. You just have to make a partition and format your drive for using.
Please make sure whether you had partitioned and formatted. First of all, you must partition and format for recognizing the new drive in the Windows Explorer.
Within Win98 series, please use the Fdisk.
Within Win2000 &
To open the Disk Management
1Click Start, point to Settings, and then click Control Panel.
2
3In the left panel, expand Storage, and then expand Disk Management.
Contact SAMSUNG WORLD WIDE
If you have any comments or questions regarding a Samsung products.
The Names and Content of Toxic and Hazardous Substances or Elements
O : Indicates that the concentration of the hazardous substance in all h omogeneous materials in the parts is below the relevant threshold of the
X : Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the
" Hybrid Disk Drive products are licensed for use only on devices that deploy the Windows VISTA operating system as the principle operating system. If you or any other party install(s) an operating system on the computing device that is not Window Vista, the use of this Hybrid Disk Drive may require an additional license from Microsoft.
For further information, please contact Microsoft. "
SAMSUNG ELECTRONICS CO., LTD.
STORAGE SYSTEM DIVISION
HEAD OFFICE:
FAX :
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
This marking shown on the product or its literature, indicates that
it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
C Samsung Electronics Co., Ltd. Printed in Korea.
2.5" HDD INSTALLATION GUIDE
Samsung does NOT guarantee any data on your drive, please always
Precautions
1MB = 1,000,000bytes / 1GB = 1,000,000,000 bytes.
Actual accessible capacity may vary from advertised capacity due to formatting and partitioning of the hard drive, as well as due to your computer's operating system.
Do not drop, shock or strike.
If apply impact to the HDD, it causes a Bad Sector by crashing between Head and Media. Do not stack. Do not external shock and vibration.
Do not remove all items, such as Hard drive label, warranty label.
Warranty void if any stickers or labels are removed or damaged. Never disassemble hard drives.
Do not touch the circuit board with hands or tools.
Protect the HDD from Electrostatic Discharge(ESD).
MR Head is very sensitive in Electrostatic.
Keep the HDD in their static shielding bag.
Avoid extreme temperatures and humidity places.
Humidity causes a drive malfunction by reacting with an ingredient of oil in Disk and Head surface. Also, parts can be corrode by leaving in humidity.
When use an external case DO NOT DROP! DO NOT PRESS!
Do not drop or fall while using and being storage the external case.
An external case is easy to transfer, but can be shocked easily also.
Check the External case's Grounding
External case's Grounding prevents HDD malfunction form ESD
PATA Installation
Configuring your Hard Disk Drive (Master, Slave)
Installation Your Hard Drive
Note: - Turn off the system power !
SATA Installation
Installing the hard disk
Note: SATA 1.5Gb/s Speed Limit Jumper setting Only for SATA 3.0Gb/s products. In some rare cases SATA 1.5Gb/s hosts can not establish SATA interface connection with SATA 3.0Gb/s devices due to interface protocol issues.
In this case the jumper may be installed as shown on the figure below to force the device to negotiate for SATA 1.5Gb/s speed.
Installing the hard disk
2 Make the computer detect the hard disk.
1If your computer supports IDE HDD Auto Detection, the hard disk drive will automatically be detected.
2If your computer does not support auto detect, go into the User Define Mode and by referring written information on the product, set the correct settings for Cylinder, Head, and Sector and if some Bios must be, set the HDD Mode to LBA.
3Save the changed details and exit.
2.Partitioning and Formatting the Drive
Refer to your Operating System manual or system manual for partitioning and formatting.
3. Samsung World Wide Web Site
Additional information can be obtained at www.samsunghdd.com.
Do Not Connect
In Reverse !!
Computer
Main Board
SATA
Interface
Cable
Power Cable
1. Making Computer Detect the New Device
Run the CMOS (BIOS)
1 Go into CMOS screen during the booting of the computer.
FAQs
Serial SATA
Host Adapter
For descriptive details of the program, refer to the computer's user's manual
Format does not work if there is no partition.