Simplified Panel, Specialized for

Remote Control from Other Devices

The AR-200S can be used as a dedicated playback device, which is controlled by means of instructions from other devices, and which employs phrases created with the AR-3000/200 and saved on CompactFlash cards.

Audio Recording System Uses No

Moving Parts

The AR-200S uses memory cards in an audio recording system that has no moving parts. The system uses no rotating parts or drive mechanism, so it???s practically maintenance free. It also features excellent sound quality and superior reliability.

High-Quality Recording and

Playback

Roland???s innovative RDAC system enables high- quality recording and playback using less data. You can select recording settings tailored to the usage circumstances and the capacity of the card, with six different sampling frequencies and four levels of signal processing (RDAC-Mode). This ensures compatibility for recording and playback for a variety of situations and applications.

All recorded phrases are saved on memory cards, allowing you to quickly play phrases for any situation, simply by changing cards.

*Maximum recording time with use of 128 MB CompactFlash cards (with monaural recording)

A Variety of Control Terminals for a Wide Range of Playback Methods

The AR-200S features ???Control Input Terminals??? as control connectors. This permits connection of switches, sensors, program timers, and other devices, enabling control of the unit from another location. In addition, the AR-200S can be controlled with a computer via the RS-232C port.

Compact Half-Rack Size Body

The 1U half-rack size body takes up practically no space. The AR-200S can be mounted in any standard 19-inch EIA rack using the optional rack mount adapter.

HIGH (44.1 kHz)/16-bit Linear: 24 minutes (approximately 11 seconds/MB)

Allows DC-Powered Operation

LONG1 (22.05 kHz)/RDAC-MODE 3: 2 hours 11 minutes (approximately 1 minute/MB) ANNOUNCE (8 kHz)/RDAC-MODE 1: 9 hours (approximately 4 minutes 10 seconds/MB)

234

The AR-200S features input terminals for DC power supplies, making the unit compatible in a variety of usage environments.

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.

Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.

* Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.

The ??? symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power- cord plug must be unplugged from the outlet.

001

???Before using this unit, make sure to read the instructions below, and the

Owner???s Manual.

............................................................................................

002c

???Do not open (or modify in any way) the unit or its AC adaptor.

............................................................................................

003

???Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all

servicing to your retailer, the nearest Roland Service Center, or an authorized Roland

distributor, as listed on the ???Information??? page.

............................................................................................

004

??? Never use or store the unit in places that are:

???Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle,

near a heating duct, on top of heat- generating equipment); or are

???Damp (e.g., baths, washrooms, on wet floors); or are

???Humid; or are

???Exposed to rain; or are

???Dusty; or are

???Subject to high levels of vibration.

............................................................................................

005

???This unit should be used only with a rack mount adaptor (RAD-50) that is

recommended by Roland.

............................................................................................

006

???When using the unit with a rack mount adaptor recommended by Roland, the

rack must be carefully placed so it is level and sure to remain stable. If not

using a rack or stand, you still need to make sure that any location you choose for placing the unit provides a level surface that will properly support the unit, and keep it from wobbling.

............................................................................................

008c

???Be sure to use only the AC adaptor supplied with the unit. Also, make sure

the line voltage at the installation matches the input voltage specified on

the AC adaptor???s body. Other AC adaptors may use a different polarity, or be designed for a different voltage, so their use could result in damage, malfunction, or electric shock.

............................................................................................

008d

???Take care not to exceed the maximum rated specifications (100 mA) when

using the DC OUT terminal for the power supply.

............................................................................................

009

???Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards!

...........................................................................................

010

???This unit, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause

permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an

audiologist.

...........................................................................................

011

???Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.

...........................................................................................

012c

??? Immediately turn the power off, remove the AC adaptor from the outlet, and request servicing by your retailer,

the nearest Roland Service Center, or an autho- rized Roland distributor, as listed on the ???Infor- mation??? page when:

???The AC adaptor or the power-supply cord has been damaged; or

???If smoke or unusual odor occurs

???Objects have fallen into, or liquid has been spilled onto the unit; or

???The unit has been exposed to rain (or otherwise has become wet); or

???The unit does not appear to operate normally or exhibits a marked change in performance.

...........................................................................................

013

???In households with small children, an adult should provide supervision until

the child is capable of following all the rules essential for the safe operation of the unit.

...........................................................................................

014

???Protect the unit from strong impact. (Do not drop it!)

...........................................................................................

015

???Do not force the unit???s power-supply cord to share an outlet with an unrea- sonable number of other devices. Be especially careful when using extension

cords???the total power used by all devices you have connected to the extension cord???s outlet must never exceed the power rating (watts/ amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up

and eventually melt through.

...........................................................................................

016

???Before using the unit in a foreign country, consult with your retailer, the

nearest Roland Service Center, or an authorized Roland distributor, as listed on the ???Information??? page.

101b

???The unit and the AC adaptor should be located so their location or position

does not interfere with their proper ventilation.

...........................................................................................

102d

???Always grasp only the output plug or the body of the AC adaptor when

plugging into, or unplugging from, this unit or an outlet.

...........................................................................................

103b

???At regular intervals, you should unplug the AC adaptor and clean it by using a

dry cloth to wipe all dust and other accumulations away from its prongs. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time. Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to fire.

...........................................................................................

104

???Try to prevent cords and cables from becoming entangled. Also, all cords and

cables should be placed so they are out of the reach of children.

...........................................................................................

106

???Never climb on top of, nor place heavy objects on the unit.

...........................................................................................

107d

??? Never handle the AC adaptor body, or

its output plugs, with wet hands when plugging into, or unplugging from, an outlet or this unit.

...........................................................................................

108b

???Before moving the unit, disconnect the AC adaptor and all cords coming from

external devices.

...........................................................................................

109b

???Before cleaning the unit, turn off the power and unplug the AC adaptor from

the outlet.

...........................................................................................

110b

???Whenever you suspect the possibility of lightning in your area, disconnect the

AC adaptor from the outlet.

...........................................................................................

118c

???Keep any removed screw terminals, the ground terminal screw, screw terminal

cover, included Euroblock connector, rubber feet, and card protector attachment screws safely out of children???s reach so as to prevent these pieces from being swallowed accidentally by young children.

...........................................................................................

Power Supply

301

???Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect

a power supply noise filter between this unit and the electrical outlet.

302

???The AC adaptor will begin to generate heat after long hours of consecutive

use. This is normal, and is not a cause for concern.

307

???Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.

Placement

351

???Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of

interference.

352a

???This device may interfere with radio and television reception. Do not use

this device in the vicinity of such receivers.

352b

???Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so

they are at a greater distance from this unit, or switch them off.

355b

???When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.

Maintenance

401a

???For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to

wipe the unit thoroughly with a soft, dry cloth.

402

???Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

Additional Precautions

???Keep the included Euroblock connector in a safe place out of children???s

reach, so there is no chance of them being stepped on accidentally.

552

???Unfortunately, it may be impossible to restore the contents of data that was stored on a memory card once it has been lost. Roland Corporation

assumes no liability concerning such loss of data.

553

???Use a reasonable amount of care when using the unit???s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling

can lead to malfunctions.

554

???Never strike or apply strong pressure to the display.

556

???When connecting / disconnecting all cables, grasp the connector itself??? never pull on the cable. This way you will avoid causing shorts, or damage

to the cable???s internal elements.

558b

???To avoid disturbing your neighbors, try to keep the unit???s volume at

reasonable levels (especially when it is late at night).

559a

???When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equiv-

alent packaging materials.

562 (Modified)

???Some connection cables contain resistors. Do not use cables that incor- porate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.

Before Using Cards

Using Memory Cards

704

???Carefully insert the memory card all the way in???until it is firmly in place.

fig.CFslot

CompactFlash???

705

???Never touch the terminals of the memory card. Also, avoid getting the

terminals dirty.

707

???This unit???s memory card slot accepts CompactFlash memory cards.

Microdrive storage media are not compatible.

708

???CompactFlash cards are constructed using precision components; handle the cards carefully, paying particular note to the following.

???To prevent damage to the cards from static electricity, be sure to discharge any static electricity from your own body before handling the cards.

???Do not touch or allow metal to come into contact with the contact portion of the cards.

???Do not bend, drop, or subject cards to strong shock or vibration.

???Do not keep cards in direct sunlight, in closed vehicles, or other such locations (storage temperature: -25 to 85?? C).

???Do not allow cards to become wet.

???Do not disassemble or modify the cards.

Copyright

851

???Unauthorized recording, distribution, sale, lending, public performance, broadcasting, or the like, in whole or in part, of a work (musical compo- sition, video, broadcast, public performance, or the like) whose copyright is

held by a third party is prohibited by law.

853

???Do not use this unit for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this unit.

Front Panel

1.PLAY/CLIP Indicator

Lights during playback of phrases.

Also lights during recording of phrases when the input level is too high (at clipping level).

2.REC Indicator

Lights during recording of phrases.

3.Display

Phrase numbers are indicated here.

4.MEMORY CARD Slot

Slot for inserting CompactFlash cards.

5.Eject Button

Press to eject the CompactFlash card.

Rear Panel

6.Ground Terminal

Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that the surface feels gritty to the touch when you touch this device, microphones connected to it, or the metal portions of other objects, such as guitars. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are concerned about this, connect the ground terminal (see figure) with an external ground. When the unit is grounded, a slight hum may occur, depending on the particulars of your installation. If you are unsure of the connection method, contact the nearest Roland Service Center, or

an authorized Roland distributor, as listed on the ???Information??? page.

927

Unsuitable places for connection

???Water pipes (may result in shock or electrocution)

???Gas pipes (may result in fire or explosion)

???Telephone-line ground or lightning rod (may be dangerous in the event of lightning)

7.Audio I/O Terminals

Terminals for input and output of analog audio.

8.INPUT VOLUME Knob

Adjusts the volume level of signals input to the audio input terminals.

9.Control/Power Input Terminals (CONTROL A)

Terminals for external control signals used to control the AR-200S and for connecting to an external DC power supply (p. 10, p. 11).

*The terminal block features a protective cover. Be sure not to lose the cover when making connections to the terminals or other times when the cover is removed. Also be sure to keep the removed cover out of the reach of children.

10.Control I/O Terminals (CONTROL B)

Terminals for external control signals used to control the AR-200S and for connecting to an external DC power supply (p. 10, p. 11, p. 12, p. 13, p. 15, p. 23).

11.RS-232C Connector

Allows for communicating with computers or other equipment (p. 9, p. 17).

12.AC Adaptor Jack

Accepts connection of the supplied AC adaptor.

*Be sure to use only the PSB-1U AC adapter.

Bottom Chassis

13.REC MODE Switches

Used for recording settings (p. 14).

14.MODE Switches

Used for switching the playback mode and output level (p. 22).

Display Examples

*Depending on the playback mode (p. 10), a phrase with a different number than the one displayed may be played back.

Attaching the Rubber Feet (Included

Items)

Attach these as required, such as when you???re using the AR-200S without mounting it on a rack or the like.

Peel off the double-sided tape from the rubber feet and affix the rubber feet at the locations shown in the following figure.

fig.Set-01

Rack Mounting (Important Notes on Heat Radiation)

When you are mounting the unit on a rack or the like, give attention to the following points to ensure efficient cooling.

???Install in a well-ventilated location.

???Avoid mounting in a sealed rack. Warm air within the rack cannot escape and is sucked into the unit again, making efficient cooling impossible.

???When you are using a stacked mounting arrangement, be especially sure to provide for adequate ventilation within the rack to keep discharged air from being sucked back into the unit. If the back surface of the rack cannot be kept open, then provide a ventilation port or ventilation fan at the upper area of the back surface of the rack, where warm air accumulates.

???When you are using the unit in a portable case or rack, remove the covers from the front and back surfaces of the case, so that the front and back surfaces of the unit are not obstructed.

*When placing the unit on the rack, be careful not to pinch your fingers.

*For more information about installation, also see ???Placement??? in the Important Notes (p. 3).

Rack-Mounting the AR-200S

By attaching a rack mount adaptor (RAD-50: sold separately) to the AR-200S, you can install it in an EIA rack. One RAD-50 can accommodate up to two AR- 200S units.

1.Remove the four rubber feet from bottom of the unit.

fig.Set-02.e

Note: Do not use these holes.

2.Attach the RAD-50 adaptor to the AR-200S using the screws that are

supplied with the RAD-50.

fig.Set-03

RAD-50

Attaching the Card Protector

By attaching the Card Protector (supplied) to the AR-200S, you can prevent the memory card from inadvertently being removed from the AR-200S.

1.After confirming that the card is securely inserted in the card slot, use the provided screws to attach the Card Protector, as shown in

the figure below.

fig.CardProtect.e

Card Protector

With the AR-200S, recorded audio and non-audio information (phrase data) is stored on cards.

Optional Roland CompactFlash cards (PM-***-CF Series) are recommended for use with the AR-200S.

Up to a maximum of 1000 phrases can be saved to cards formatted with the AR-200S.

*To format a card on the AR-200S, transmit the format command via the RS- 232C port.

Important Notes on Handling Cards

???When Inserting

Insert the card all the way into the card slot.

*Insert the card straight into the slot, with the card label facing upwards.

Side with arrow should face upwards

CompactFlash???

???When Removing

To remove the card, press the eject button. Press the eject button firmly, all the way in.

*Never remove a card during recording, playback, or formatting. Furthermore, do not turn off the power or remove the AC adaptor cord during recording, playback, or formatting. Doing so may damage the card.

Card Compatibility with Other Models in the AR Series

The AR-200S???s file format is the same as the format for the AR-3000/200.

Using Cards Formatted on Earlier Model Units with the AR-200S

???Files on PC cards used on AR-3000/200/2000/100 models can be used by copying the data to CompactFlash with the ARE-3000.

(Cards copied using AR models cannot be used.)

Using Cards Formatted on the AR-200S with

Earlier Models

???Cards can be used as is with the AR-3000/200 by copying the data to PC card (PM series) with the ARE-3000.

???Cards cannot be used with the AR-2000/100.

(Cards copied using other AR models cannot be used.)

Please download the ARE-3000 (free of charge) from the following URL. http://www.rssamerica.com/

fig.Use-01.e

Momentary Switch

Pressing the switch plays back a set announcement, guidance message, explanation, or the like

???Set announcements played back as required

???Broadcast of museum exhibition explanations or guidance

Sensor

Program Timer

p m .

Control timer for automatic broadcasts

???Playback of message broadcasts and announcements at regular, set times in offices, factories, or other such areas

???Broadcasts at set times of upcoming events at amusements areas

Sensor-triggered automatic broadcasts

???Guidance announcements made upon detection of a person???s presence

???Playback of event performances at attractions and other sites

Types of External Control

AR-200S

Control Signal

Audio Signal

Control Output

Control signals can be output during or after phrase playback to control an external device (p. 18).

fig.Use-02.e

Busy Out

Power Amp

Control Signal

Audio Signal

AR-200S

Only during phrase playback, power amp or other gear is powered up (offset time set to five seconds)

Lamp lights during phrase playback

Power Amp

Power Unit

Power

Reray

Switch

AR Control with a computer

AR-200S

Control signal Audio signal

You can use the control input and DC input screw terminals (CONTROL A) and the 25-pin D-sub-type control I/O connector (CONTROL B) on the AR- 200S???s rear panel to control the AR-200S from an external device.

This chapter explains how to connect external devices and make the settings for the AR-200S.

*The control I/O connector cannot be used to switch the power to the AR unit on or off.

About Phrases

On the AR-200S, a single unit amount of recorded data (audio signals) is called a phrase. Phrases are managed using phrase numbers.

Types of Control Input Playback

There are four types of control input playback: Playback by Card Data (p. 10), Direct Playback (Last-In) (p. 11), Binary Playback (p. 12), and Interval Playback (p. 13). You cannot use more than one type of playback at the same time.

Operational Specifications for Control Input Playback

*The AR-200S features one type of control input recording, ???Terminal Rec???(p. 14).

What Is No-voltage/Make-contact?

This is contact that makes starting possible simply by connecting two lines to the control input connectors and shorting their ends. This is a general-use method that lets you create start systems easily using only a switch and without any need for a power source, enabling easy use for a variety of applications.

You can control playback and recording with the AR-200S using On/Off signals from No-voltage/Make-contact input from an external source. By connecting infrared sensors or switches, relays, and timers, or other

external starting connectors to the AR-200S, you can use the unit in an even wider variety of applications.

The AR-200S can help simplify installation operations by making the starting- side contact hot and sharing the ground as the common connector.

For more on the control input specifications, refer to Control I/O

Direct Playback (Normal Playback)

A phrase is played back when a control signal is input directly to the terminal with the number to which the phrase is assigned. Up to 9 phrases can be played back.Assign Phrases 1 through 9 beforehand to Port Nos. 1 through 9, respectively.

This makes it very convenient when you want to specify a desired phrase directly using a switch, relay, sensor, or other such means.

fig.CtrIn-Dir01.e

A Control

Signal

Connectors Used for Direct Play (Control I/O Connector)

10 (STOP) This stops phrase playback.

11/12 (COM) Shorting with the above terminals results in ???ON.???

*Control Input and DC Input Terminal (CONTROL A) ???1, 2??? are connected in parallel with Control I/O Connector (CONTROL B) ???1, 2.???

Basic Operation of Direct Playback (Normal Playback)

fig.CtrIn-Dir02.e

Port No. 1

Port No. 2

STOP Port

Audio Output

001 Interrupted

Playback: Input a control signal to a Port, 1???9.

??? The phrase assigned to the Port is played back. Stopping: Input a control signal to Port 10 (STOP).

??? Playback of the phrase is stopped.

Terminal Priorities

fig.CtrIn-DirPrior.e

???When a new high-priority control signal is input during phrase playback

Playback of the current phrase is stopped, and playback of the specified

phrase begins.

Connector Specifications (p. 23) in the Appendices.

Playback By Card Data

Cards Created on the AR-3000 or AR-2000

Playback will use the settings (playback method) recorded in the card. For more information, please refer to the owner???s manuals for each device.

fig.CtrIn-Dir03A.e

Port No. 1

Port No. 2

Audio Output

002001

002 Interrupted

*Some functions are not available. (p. 21)

Card made on the AR-200/100

*If a control signal has a lower priority than that of the phrase currently being played back, the specified phrase is not played back.

???While the control signal is continuously input

Playback is repeated while the signal is input.

Playback mode is available Direct Playback (Normal).

Phrases 1 through 9 are assigned to the control I/O connector Port Nos. 1 through 9.

fig.CtrIn-Dir04.e

Port No. 1

Audio Output

001 001 001

Playback Instructions (Control Input Playback)

Specifying Phrases in Binary Notation

(Binary Playback)

By inputting binary (Base 2) signals to Port Nos. 1 through 8 to select a phrase and inputting a start message to the START terminal, you can then play back the selected phrase. A maximum of 250 phrases can be selected and played back with this method.

This allows you to specify 250 phrases with control signals (from a switch or other ON/OFF signal device), without having to use computers or other complicated equipment.

fig.CtrIn-Bin01.e

Binary Specification

Port No. 1???8

8 7 6 5 4 3 2 1

01110000

*To conduct Binary Playback, you will need to obtain a control device capable of generating binary signals.

Connectors Used in Binary Playback

fig.CtrIn-BinPin.e

Even without connecting to all eight connectors used for making the binary specifications, you can still conduct Binary Playback. The number of phrases that can be specified is determined by the formula ???two to the nth power minus one??? (with ???n??? being the number of connectors used).

Example:

Using three timers or other such devices capable of outputting the necessary signals gives two to the third power minus one (i.e., 8 - 1 = 7), meaning you can specify the seven phrases 001 through 007.

However, start signals feature other special requirements.

Operational Specifications of Binary

Playback

START Port

001

Audio Output

Playback: Specify the phrases using combinations of 0 (Off) and 1 (On) signals to Port Nos. 1 through 8, and Port Nos. 11 and 12, and input a control signal to the Port No. 9 (START).

??? This plays back the specified phrase. Stopping: Input a control signal to Port No. 10 (STOP).

??? This stops playback of the phrase.

The basic operation of Binary Playback is shown below.

fig.CtrIn-Bin03.e

???Binary specified phrases are played back repeatedly.

???Playback is repeated while the start signal is continuously input.

???You can begin playback of phrases by specifying phrases in binary with the start signal continuously being input.

???When the START connector control signal switches to Off, the current phrase finishes, and then playback is stopped.

???No action results when a new start signal is input while a phrase is being played back.

AR-200S Settings

With the power to the AR-200S switched off, set the MODE switches on the bottom panel as shown below.

SW 1: OFF, SW 2: ON

To Specify Phrases with Binary Signals

Example: Specifying Phrase 112 (Phrase #: 112)

Convert the phrase number to a binary signal number. ???0??? (Off), ???1??? (On)

According to the Phrase Number / Binary Signal chart (p. 13), the phrase number ???112??? is converted to the binary number ???01110000.???

Phrase Number (Binary)

Input of binary specifications should be completed in no more

than 50 milliseconds.

Repeated Playback of Phrases

(Interval Playback)

The specified phrase will be played back at fixed intervals. Make each of the terminal settings beforehand for the playback interval and phrases to be played back.

???When making settings in Interval Playback mode, assign Phrases 1 through 9 to the control output connectors 1 through 9.

???The playback interval settings are shown below.

Phrase Number / Binary Signal chart

fig.Bin-Chart.e

Playback Instructions (Control Input Playback)

Operational Specifications of Interval Playback

fig.CtrIn-Int01.e

Port No. 2

STOP Port

002002

Audio Output

002 Interrupted

Interval time used for phrases

Playback: Input control signals to the control Input/output connectors No. 1 through 9.

??? Results in the repeated play of the phrase assigned to the terminal.

Stopping: Input a control signal to Port No. 10 (STOP). ??? This stops playback of the phrase.

AR-200S Settings

With the power to the AR-200S switched off, set the MODE switches on the bottom panel as shown below.

SW 1: ON, SW 2: ON

Required Settings for Recording Audio Signals (Recording Settings)

In order perform recording matched to usage conditions, including the connected equipment, recording source, sound quality, time, and playback system, you make recording settings.

???Recording settings are made in phrase units. You can mix phrases having different recording settings on a single card.

???The possible recording time of a card varies according to the recording settings. For a rough guide to maximum recording times with various settings, see Card Audio Recording Time Chart (p. 21).

MODE SW Setting

With the power to the AR-200S switched off, set the MODE switches on the bottom panel as shown below.

SW 6: ON

REC MODE SW Settings

The REC MODE switches are located on the AR-200S???s bottom panel. You can change the recording settings by changing the settings of the REC MODE switches.

Each switch is ON when in the upward position, and OFF when in the downward position.

When the AR-200S is shipped from the factory, all switches will be OFF.

*Use a pointed object to change the ON/OFF settings of the REC MODE switches.

*Set the REC MODE switches with the power to the AR-200S turned off.

fig.RecModeSW

RDAC-Grade (Sampling Frequency)

The RDAC grade is the type of sampling frequency for digital recording. On the AR-200S, you can select from among six grades.

STANDARD is best for ordinary recording. ANNOUNCE uses up the least card space, and is best for recording announcements, narration, and the like. When you are recording audio such as a narration with ANNOUNCE or LONG2, you can record with higher clarity by using the equalizer to cut the bass range. Select an RDAC grade that matches the circumstances of use.

Selecting RDAC-Grade

With the power to the AR-200S turned off, set the REC MODE switches on the bottom panel as shown below.

RDAC-Mode (Signal Processing Format)

The RDAC mode is a type of digital data processing system for recording. On the AR-200S, you can select from among four modes.

Selecting RDAC-Mode

With the power to the AR-200S turned off, set the REC MODE switches on the bottom panel as shown below.

If the type of card does not provide the recording time you want, change the RDAC mode or RDAC grade setting to use less card capacity, then perform recording again.

Card Audio Recording Time Chart (p. 21)

What???s RDAC?

RDAC (Roland Digital Audio Coding) is a proprietary audio recording standard from Roland.

It achieves high sound quality and also makes it possible to record for long times.

If You???re Not Sure About Which Grade and Mode to Choose

The optimal grade and mode vary according to the usage conditions, including the connected equipment, recording source, sound quality, time, and playback system.

The factory default settings are RDAC-Grade: LONG1; and RDAC-Mode: MODE1.

First, try recording and playback with these settings. In most cases, this yields satisfactory sound quality.

Recording Type (Stereo/Mono)

Select either stereo recording or mono recording.

Choosing mono recording gives you recording times that are twice as long as with stereo recording.

Selecting Recording Type

With the power to the AR-200S turned off, set the REC MODE switches on the bottom panel as shown below.

What is mono recording

In the case of mono recording, input the audio signal to the ???MONO/L??? input terminal. When audio signals are input simultaneously to the ???MONO/L??? and ???R??? input terminals, L and R are mixed and recorded.

Line Thru Output (p. 19)

???REC MODE SW 6: OFF (Mono)

When audio signals are input to ???MONO/L,??? output is from OUTPUT L and R. When audio signals are input to ???R,??? output is from OUTPUT R only. When audio signals are input to both ???MONO/L??? and ???R,??? solely the signals input to ???MONO/L??? are output from OUTPUT L, while the ???MONO/L??? and ???R??? signals are mixed and output from OUTPUT R.

???REC MODE SW 6: ON (Stereo)

Audio signals input to ???MONO/L??? are output from OUTPUT L, and audio signals input to ???R??? are output from OUTPUT R.

Connectors Used in Terminal Rec

You can specify phrases by inputting binary (base 2) signals to the Port Nos. 1 through 8, and perform record, playback, and delete functions by inputting control signals to Port Nos. 9 and 10. A total of 250 phrases can be specified with control signals (On/Off). This is convenient when you want to control recording from an external control device.

fig.CtrIn-Rec01.e

Binary Specification

Port 1???8

8 7 6 5 4 3 2 1

01101111

*To conduct binary control, you need to provide a control device that can generate binary signals.

fig.CtrIn-RecPin.e

Recording Instructions (Terminal Rec)

Operational Specifications for Terminal Rec

Phrases are specified by combinations of signals of 0 (Off) and 1 (On) to the Port Nos. 1 through 8 as well as Port Nos. 11 and 12, and record, playback, and delete functions are specified with combinations of control signals of 0 (Off) and 1 (On) to Port Nos. 9 and 10.

Presence or Absence of Phrases

If there is a binary-specified phrase that has already been recorded, a signal is output from the CONT OUT connector (Port No. 15). If there is an empty phrase, no signal is output.

*During Terminal Rec, the CONT OUT connector functions as a connector for signals confirming the presence or absence of phrases. Note that this differs from

the normal function of CONT OUT.

fig.CtrIn-Rec02.e

Timing Chart (The presence or absence of phrases)

Binary Specification

Port No.1???8

Tbcd

Control Out (the presence or absence

of phrases)

Recording

9:0 (Off)

10:1 (On)

While control signals are being input, the specified phrase is recorded. When input of the control signal stops, recording then ends.

fig.CtrIn-Rec03.e

Timing Chart (Rec)

Tbrs Tbrh

*Recording does not start if there is a binary-specified phrase that has already been recorded (the recording instruction is disabled). When recording, either specify an empty phrase or delete the existing phrase before recording the new one. Additionally, in Terminal Rec, since a make signal is output from the CONT OUT connector when a specified phrase has already been recorded, this allows confirmation using a connected external control device.

*The remaining recording time appears in the display when ten seconds or less of recording time remains.

*When you???re using the Terminal Recording Mode, recording takes place immediately, without entering trigger recording standby.

*Use the INPUT VOLUME knob to adjust the recording level so that the PLAY/ CLIP indicator does not light.

Recording Instructions (Terminal Rec)

Playback

9:1 (On)

10:0 (Off)

The specified phrase is played back.

Even when control signals are input continuously, the phrase is played back one time only and then ends.

fig.CtrIn-Rec04.e

Timing Chart (PLAY)

(msec)

*Playback does not begin if the binary-specified phrase is empty (the playback instruction is disabled). When playing back, specify a phrase that has already been recorded.

Delete

9:1 (On)

10:1 (On)

First, when ON is input to Port No. 10, and then ON is input to Port No. 9, deletion of the specified phrase begins. Deletion ends when the signal from the CONT OUT connector confirming the presence or absence of the phrase changes to OFF.

*Deletion does not begin if the binary-specified phrase is empty (the delete instruction is disabled). When deleting, specify a phrase that has already been

recorded.

fig.CtrIn-Rec05.e

Timing Chart (Delete)

Tbdh

Control Out (the presence or absence

of phrases)

*Play phrase output delay time is dependent on the card used.

To Specify Phrases with Binary Signals

Note that the way phrases are specified in Terminal Rec differs

from that used in Binary Playback.

Example: Binary specification of Phrase 112 (Phrase #: 112) Convert the phrase number to a binary signal number. ???0??? (Off), ???1??? (On)

The phrase number ???0001??? is specified in the binary notation as ???00000000,??? and as shown in the Phrase Number / Binary Signal chart

(p. 13), each subsequent specification is shifted by one.

248 11111000

249 11111001

25011111010

The phrase number ???112??? becomes the binary signal ???01101111.???

You can use the 25-pin D-sub-type control I/O connector (CONTROL B) on the AR-200S???s rear panel to control an external device from the AR-200S.

The AR-200S outputs two kinds of control signals, Busy Out and Control Out. This chapter explains how to connect external devices and make the settings for the AR-200S.

Starting Another Device (Busy Out)

Busy Out is a continuous signal output from the BUSY OUT pins during playback (as well as during recording and recording standby) of audio phrases, pattern phrases, and song phrases.

This signal can be used to start amplifiers and other external devices in sync with phrase playback.

Busy Out Specifications

No-voltage/make-contact

Contact capacity: Max. DC 30 V, 3 A

Port Nos. 13 and 17 have Make-contact during output.

Output of Busy Out Signals In Dual Mono Mode (p. 19)

When in Dual Mono mode, the Busy Out signal of the left channel is output from the BUSY OUT pins (Port Nos. 13 and 17), and the right channel Busy Out signal is output from the CONT OUT pins (Port Nos. 15 and 18).

fig.CtrOut-02.e

Controlling Another Device

(Control Out)

The Control Out signal is output for a duration of one second from the CONT OUT pins after playback of audio phrases, pattern phrases, and song phrases. This signal can be used to start amplifiers and other external devices in sync with phrase playback.

You can set the time that is to pass after phrase playback before output is made to anything from 0 seconds to 59 minutes 59 seconds. Settings are made in phrase units.

Note that if playback of a phrase in progress is cut off, no

Control Out signal is output.

Control Out Specifications

No-voltage/make-contact

Make-contact time: 1 second, Contact capacity: Max. DC 30 V, 3 A

Port Nos. 15 and 18 have Make-contact during output.

Output of Control Out Signals In Dual Mono Mode (p. 19)

Note that Control Out signals are not output in Dual Mono Mode (the Control Out settings are not effective).

In such instances, if the Busy Out output settings have been made, then the Busy Out signal of the left channel is output from the BUSY OUT pins (Port Nos. 13 and 17), and right channel???s Busy Out signal is output from the CONT OUT pins (Port Nos. 15 and 18).

AR-200S Settings

Settings for these parameters cannot be made with the AR-200S. Only phrases set on the AR-3000 are effective. For detailed information, please refer to the AR-3000 owner???s manual.

Moreover, by using an optional AR-3000 to create and edit phrases, you can also use the following functions.

For detailed information, please refer to the AR-3000 owner???s manual.

*You cannot make settings for these parameters on the AR-200S. Furthermore, they are effective only with phrases whose settings have been made on the AR- 3000.

Playing Data for Two Units on the Left and Right (Dual Mono Mode)

The Dual Mono mode is a feature for playing different mono audio phrases independently on the left and right channels.

By outputting odd-numbered phrases (001, 003, ...) from the left channel and even-numbered phrases (002, 004, ...) from the right channel, you can play back two units??? worth of phrases using only the one device.

You can also play back separate phrases on the left and right channels either simultaneously, or shifted.

fig.DualMono.e

To Users of the AR-2000/100 (Legacy Models)

On the AR-2000/100 (legacy models), this ???Dual Mono Mode??? is the function called ???Channel Playback Mode.??? When using them, please try to keep in mind that the two functions are identical.

Adjusting the Sound Quality During

Audio Phrase Playback (EQ???Equalizer)

You can adjust the quality of the sound during audio phrase playback with two-band equalization.

Playing Back Phrases in the Order They Are Selected (Program Playback)

You can have the group of preset phrases play back in the order they are selected by inputting a control signal to the START port.

With program playback, you can register up to a maximum of 100 phrases in each of the five patterns of Programs 1 through 5.

Since the order and duration of the phrases is predetermined, this is a convenient option when you have only one contact, such as a timer or switch, with which to trigger this action.

Line Out (Thru) Setting During Phrase

Playback

You can take audio from INPUT, mix it during phrase playback, and mixed it from OUTPUT.

fig.LineThru-01.e

CD player or other sound playback device

INPUT

OUTPUT

Sound input to INPUT

+

AR sound phrase

Power Amp

This is useful when you want to do things like taking music from INPUT and layering it with narration phrases as background music.

You can also make the Input sound fade out or in.

Line throughput is possible only for signals connected to the INPUT terminals.

Line Thru Output Specifications

The following output specifications apply, depending on the Line Thru settings.

When fade-out or fade-in settings have been made

About playback

Control Input Playback (Direct/Binary) does not work as intended

???Make sure the MODE switches??? settings (Direct/Binary) are selected correctly. You cannot achieve control input playback merely by connecting a device to the port. Be sure to set the control input mode and match the method used for connecting to the connectors (p. 22).

Phrases in Direct Playback cannot be selected as intended

???When the card is formatted, phrase assignments for Port Nos. 1 through 9 are such that Phrase 001 is assigned to Port No. 1, Phrase 002 to Port No. 2, and so on up to Phrase 009, which is assigned to Port No. 9. Check to make sure that the phrases are properly selected.

Phrases play repeatedly in Direct Playback

???Check to make sure that ???INTERVAL PLAYBACK??? is not selected with the MODE switch settings (p. 22).

Card made on the AR-3000

Phrases are not played back (PLAY indicator is flashing)

???Is the MTC ???Sync Source??? set to ???MTC????

When not synchronizing playback with MTC and using the AR-200S as a slave, set ???Sync Source??? on the AR-3000 to ???Internal.???

Pattern phrases and song phrases are not played back as intended

???Phrases composed from pattern phrases or song phrases will not be played back properly unless they are saved as actual phrases (if the composed phrase is not saved, the next phrase is sought and then played back). Check the AR-3000 to confirm whether or not the composite phrase has been saved.

The start of phrase playback is delayed when playback is controlled from an external device

???Has the ???Delay Time??? been set for the phrase?

Check the AR-3000 to confirm whether or not the delay time has been set. Check the control signals being sent from the external control device, connections and so on once more.

Others

No sound

???Reconfirm that the power to the AR-200S or connected device is on.

???Reconfirm that the volume control on the AR-200S or connected device is turned up.

???Reconfirm that there are no shorts in any connector cables.

Phrase number flashes during playback

???This indicates that a MIDI phrases is playing back.

Although the AR-200S is not MIDI phrase-compatible, if a specified phrase is a MIDI phrase, the phrase number will flash.

There is a scraping sound coming from the AR-200S

???In situations such as when control signals are input continuously, the movement of the internal relays may make a scraping sound, but this does not indicate any malfunction. To prevent overuse and failure of the relay, you may also switch to Interval Playback in order to have the relay move only once (p. 13).

The volume of the device connected to the output connector is low

???Could you be using a connection cable that contains a resistor? Use a connection cable that does not contain a resistor.

Card Audio Recording Time Chart

The following table shows recording times available for cards formatted for the AR-3000.

*Recording times listed are for mono recording. Recording times are halved when data is recorded in stereo.

*These times are for when 1 phrase is recorded continuously, and are provided for your reference when recording. The recording time will depend on the combination of the grade settings of each phrase recorded in each memory card.

*Minimum recording times are listed only for MODE2. Depending on conditions, you may be able to attain recording times longer than listed here.

Recorded Phrase Data

When a piece of Phrase data recorded by the AR-200S, the settings of data on the card will be as follows.

If you will be using the card on the AR-3000, refer to this list.

AR-3000 Settings That Can Be Used

When cards created with an AR-3000 are played back on an AR-200S, the resulting playback could diverge from the original. This is due to a variety of factors, including the fact that data created for settings specific to the AR-3000 cannot be used by the AR-200S. For details, see the tables below.

Phrase Compatibility

1. Phrase messages

*1: MIDI phrases are played back silently for the duration of the phrase in accordance with the playback tempo.

*2: The phrase name will not be displayed on the AR-200S.

*3: If a MIDI phrase is set, playback is silent for the duration of that phrase.

*4: The card name will not be displayed on the AR-200S.

*5: Enabled only when the playback mode is set to ???Playback by Card Data.???

*6: For binary playback, up to 250 phrases can be played back.

???Control Input and DC Input Terminal (CONTROL A) ???1, 2??? are connected in parallel with Control I/O Connector (CONTROL B) ???1, 2.???

???When using Program Playback on a PC card created by the AR-3000, use connectors 1 (INC), 3 (DEC), 5 (EXCHANGE), 9 (START), and 10 (STOP).

*Do not make any connection to NC pins, since this will cause faulty operation.

DC Power Supply

???Power can be supplied to the AR-200S from an external power supply unit (DC power supply) as well as from the AC adaptor.

???To supply power from an external power supply unit (DC power), use the Control Input and DC Input Terminal (CONTROL A) or the Control I/O Connector (CONTROL B) DC IN and GND pins.

Power Supply Specifications

DC +9???24 V, 1200 mA

*The DC OUT pin of the Control I/O Connector (CONTROL B) can be used as power supply for a sensor, etc.

???Never short a power supply pin (21, 24, 25) to the GND pin, since this will damage the unit.

???When using the DC OUT, be careful not to exceed the maximum rating (100 mA).

???For reasons of safety, do not connect the DC IN + pin of the Control Input and DC Input Terminal (CONTROL A) to metal parts such as the chassis or the Control I/O Connector (CONTROL B).

???Do not supply electrical power simultaneously to multiple connectors or terminals; doing so may result in damage to the unit.

AR-200S: Audio Recorder

Recording Format

RDAC (Roland Digital Audio Coding)

RDAC-Grade (Sampling Rate)

Playback Rate Area

RDAC-Mode (Signal Processing Method)

Recording Media

Memory Card (PM-128-CF: option)

*In order to recording/playback of audio signal, you will need to purchase one of the memory cards.

CompactFlash Card Slot

1 slot

Phrase Types

Audio Phrases (stereo/mono)

Number of Phrases

Playback Methods

Master Equalizer (Functions only when using cards that have been prepared on the AR-3000.)

High: -12 dB thru +12 dB (3/6 kHz, Shelving Type)

Low: -12 dB thru +12 dB (200/400 Hz, Shelving Type)

Residual Noise Level

-80 dBu (Input Short, INPUT VOLUME: middle, DIN-Audio, typ.)

S/N Ratio

Output: 84 dB (DIN-Audio, typ.)

RS-232C

*The setting for 38400 bps is for compatibility with legacy models (the AR-2000). However, it is a value for the communication speed that is not defined by the RS- 232C standards. Make this setting as necessary when using a legacy model by means of card conversion.

Display

7 segments, 4 characters (LED)

Controllers

INPUT VOLUME Knob

Card Eject Button

REC MODE Switches (Bottom Chassis)

MODE Switches (Bottom Chassis)

Indicators

PLAY/CLIP Indicator

REC Indicator

Connectors

LINE I/O Connector (8-pin Euroblock)

Control/Power In Terminal (5-pin Terminal Block with M3 bolts) Control I/O Connector (DB-25 type)

RS-232C Connector (DB-9 type)

Power Supply

DC 9 V (AC Adaptor)

DC 9???24 V (Control/Power In Terminal, Control I/O Connector)

Current Draw

1000 mA (When Using the AC Adaptor)

1200 mA (When Using an External Power Supply Unit)

Dimensions

218 (W) x 233.3 (D) x 44 (H) mm

8-5/8 (W) x 9-3/16(D) x 1-3/4 (H) inches

Weight

1.5 kg / 3 lbs 5 oz (Excluding AC Adaptor)

Accessories

Rubber Feet

Card Protector (with screws)

Euroblock Connector

Owner???s Manual

AC Adaptor (PSB-1U)

Options

*0 dBu = 0.775 Vrms

*In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

*In addition to the owner???s manual, the separate publication ???RS-232C Reference Notes??? is also available for those needing detailed documentation regarding RS-232C connector control.

Please download the PDF file (free of charge) from the following URL. RS-232C Reference Notes cover the following topics:

???Setup

???Overviews, detailed descriptions, and lists of commands

???Examples of usage algorithms

http://www.rssamerica.com/

Dimensions

fig.Dimensions

217.6

218

42 3.3

14.2

3.7

ASIA

TAIWAN

ROLAND TAIWAN

ENTERPRISE CO., LTD.

Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, TAIWAN, R.O.C.

TEL: (02) 2561 3339

SINGAPORE/

MALAYSIA

Roland Asia Pacific Sdn. Bhd.

45-1, Block C2, Jalan PJU 1/39,

Dataran Prima, 47301 Petaling

Jaya, Selangor, MALAYSIA

TEL: 3-7805-3263

EUROPE

EAST EUROPE

Roland East Europe Ltd.

Warehouse Area ???DEPO??? Pf.83

H-2046 Torokbalint, HUNGARY

TEL: (23) 511011

AUSTRIA/BELGIUM/

FRANCE/GERMANY/

HOLLAND/

LUXEMBOURG/

PORTUGAL/SPAIN/

SWITZERLAND

Roland Iberia, S.L.

Paseo Garc??a Faria, 33-35

08005 Barcelona SPAIN

TEL: 93 493 91 00

NORTH AMERICA

CANADA

Roland Canada Music Ltd.

(Head Office)

5480 Parkwood Way, Richmond B. C., V6V 2M4 CANADA

TEL: (604) 270 6626

Roland Canada Music Ltd.

(Toronto Office)

170 Admiral Boulevard

Mississauga ON L5T 2N6

CANADA

TEL: (905) 362 9707

U. S. A.

Roland Systems Group U.S.

14830 Desman Road, La Mirada,

CA 90638 U.S.A.

TEL: 714-521-8000