??
Use and
Care Guide
??
Use and
Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic precautions should always be observed, including the following.
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
WARNING
To reduce the risk of burns, fire, electric shock or injury to persons:
SAVE THESE INSTRUCTIONS
Contents
Product Features
High Precision??? Hair Clipper
High Precision??? Hair Clipper from Remington?? brand provides a quick and easy way to obtain
Clipper Parts
A.On/Off Switch
B.Charge indicator light
C.Charging adaptor
D.8 Attachment guide combs
(3mm, 7, 9, 12, 18, 25, L/R ear taper)
E.Oil
F.3 sectioning clips
G.Storage/travel pouch
H.Barbers Comb
I.Cleaning brush
J.Neck brush
K.Blade guard
L.Scissors
B.
A. 
L.
C.G.
I.
K.
How to Use
CHARGING YOUR HAIR
CLIPPER
Turn the clipper off
???Insert the adapter plug into the bottom of the clipper and plug the adapter unit into a power outlet. The red light will glow to indicate that it is charging.
???The clipper will be fully charged in
???The batteries cannot be overcharged, but we recommend that charging be discon- tinued if the clipper will not be used for a long period of time.
???It is advisable not to use this clipper directly from the power outlet when it has been fully charged, but if while using the clipper in cordless mode there is a noticeable drop in power, you can use directly from the power outlet. Never use under water when connected to
the outlet.
???If the clipper has not been used for a month or longer, it is advisable to recharge it for
???To preserve the life of the batteries, discharge them by running the clipper until the blades move slowly. Switch off and fully recharge. Do this every six months.
???Charge the clipper at temperatures between
???
INSTRUCTIONS FOR HAIR
CUTTING
Before starting the cut
1.Inspect the clipper making sure that it is free from hair and dirt.
2.Seat the person so that their head is approximately at your eye level.
3.Before cutting, always comb the hair so it is tangle free and as it is naturally worn.
4.Hair must be dry.
Reminders:
Cut the hair gradually using short strokes only to work gradually over the entire head. Always take off a little hair at a time. You can always trim off additional hair later.
As you work, comb the hair frequently back into the style that you are cutting. Each comb attachment is marked accoringly on its outside middle surface.
BEST TECHNIQUE
These instructions are only to be used as a guide. You may prefer to begin trimming with a longer comb attachment to avoid cutting hair too short. As you become familiar with the settings, you can select your desired length setting.
STEP 1 ??? Nape of the neck ??? Diagram 1 1. Use 3mm or 7mm1
Guide Comb.
2.Hold the clipper with the cutting edge
pointed up and begin the haircut. Start at the center of the head at the base of the neck.
3.Hold the clipper lightly against the head with the comb teeth pointing upward. Slowly lift the clipper, working upwards and outwards through the hair, trimming just a little at a time.
2.For longer hair on top, use without a
Guide Comb. Lift the hair on top of the head with a hand comb. Cut over the hand comb with the hair lifted or hold the hair between the fingers and cut it to the desired length.
3.Always work from the back of the head.
STEP 5 ??? The finishing touches ??? Diagram 5
2.To produce a clean straight line at the sideburns, reverse the hair clipper. Press the reversed clipper at right angles to the head, tips of the blades lightly touching the skin and then work downwards.
SHORT TAPERED STYLES ??? ???FLAT TOPS??? &
SHORT CUTS
1.Starting with the longest Guide Comb attached (25mm), cut from the back of the neck to the crown. Hold the Guide Comb flat against the head and slowly move the clipper through the hair, as shown.
2.Use the same procedure from the lower side to the upper side of the head, as illustrated. Then cut the hair against the direction in which it grows and level with the sides.
3.To give a ???flat top??? look, the hair on top of the head must be cut over the top of a flat comb
4.Use a closer Guide Comb to taper the hair down to the neckline as desired.
Cleaning & Maintaining Your
Clipper
AFTER EACH USE
High Precision??? Hair Clipper is washable enabling use in the shower and ease of cleaning. Therefore, to maintain the perform- ance of the cutters and trimmer, oil lightly before and after each use.
???Brush or rinse the accumulated hair from the cutters. Do not submerge the clipper in water.
???Place one or two drops of cutter oil on the blades. Turn the clipper on to distribute the oil evenly. Wipe off any excess oil.
???To clean the unit, wipe with a damp cloth and dry immediately.
! Be sure the clipper is turned off when applying the oil.
How to Use
Battery
EVERY SIX MONTHS
???At regular intervals the Blade Set should be removed and cleaned. To remove the Blade Set, remove the two screws hold- ing the large blade to the clipper body.
The Blade Set will separate from the body and can be cleaned as necessary. Replace the Blade Set and place a few drops of cutter or sewing machine oil onto the blades.
CLEANING CAUTIONS
Troubleshooting
The clipper does not work when turned on:
???Clipper must be charged for a full
Clipper cutters do not move:
???The cutting unit may be dirty and clogged. Clean the unit as directed in Cleaning & Maintaining section.
Clipper does not hold charge:
Battery Removal
When your recharge- able clipper reaches the end of its useful life, the batteries must be removed and recy- cled or disposed of properly in accordance with your local and state requirements.
CONTAINS NICKEL-
CADMIUM BATTERY.
BATTERY MUST BE RECYCLED
OR DISPOSED OF PROPERLY.
CAUTION: THESE
BATTERIES MUST BE RECYCLED
OR DISPOSED OF IN ACCORDANCE WITH
STATE AND LOCAL REGULATIONS.
Do not burn or mutilate as they may burst or release toxic materials. Do not short- circuit as this may cause burns.
The
STORAGE
???Always store this appliance and cord in a
???Do not wrap the cord of the charging adaptor around the appliance.
???Do not store in temperatures above 140??F.
The following procedure should be followed for battery removal:
???Make sure your clipper is unplugged from any outlets so you don???t risk. an electric shock.
???For your safety remove the clipper assembly. Using a phillips head screw driver, remove the 2 screws on the back of the fixed blade.
???Grasp bottom portion of the clipper with one hand and top portion with the other hand. Pull the two halves apart. You may need to twist them slightly or use a flat screwdriver to pry them apart.
ily participating in an industry program to collect and recycle these batteries at the end of their useful life when taken out of service in the United States or Canada. The RBRC?? program provides a convenient alternative to placing used
???Pull up or pry up on the battery pack and twist to remove it.
Performance Guarantee
Full
Spectrum Brands, Inc. warrants this product against any defects that are due to faulty material or workmanship for a
If the product should become defective within the warranty period, we will repair it or elect to replace it free of charge. Return your product with your name, address and day time phone number to: Spectrum Brands, Inc., Attention: Consumer Services, 601 Rayovac Drive, Madison, WI 53711. For more information call
This warranty does not cover products damaged by the following:
???Accident, misuse, abuse or alteration of the product
???Servicing by unauthorized persons
???Use with unauthorized accessories
???Connecting it to incorrect current and voltage
???Wrapping cord around appliance causing premature wear & breakage
???Any other conditions beyond our control
No responsibility, obligation, or liability is assumed for the installation or maintenance of this product.
SPECTRUM BRANDS, INC. SHALL NOT BE
RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF FITNESS
AND MERCHANTABILITY, ARE LIMITED
IN DURATION TO TWO YEARS FROM DATE
OF ORIGINAL PURCHASE.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province. Some states do not allow the exclusion or limitation of incidental, special or consequential damages.
Spectrum Brands, Inc.
If within 30 days after you have purchased your Remington?? branded product, you are not satisfied and would like a refund, return it with the sales slip indicating purchase price and date of purchase to the retailer from whom it was purchased. Spectrum Brands, Inc. will reimburse all retailers who accept the product within 30 days from the date of purchase. If you have any questions concerning the
120 VAC 60 Hz
Questions or comments:
Call
or visit
Dist. by: Spectrum Brands, Inc.,
Madison, WI 53711
Dist. by: Rayovac Canada Inc.,
Mississauga, ON L4W 2T7
REMINGTON and HIGH PRECISION are registered trademark sof ROVCAL, INC.
MADE IN CHINA
Gu?? us cui
10