Cat. No.
OWNER???S MANUAL
Please read before using this equipment.
Cat. No.
OWNER???S MANUAL
Please read before using this equipment.
FEATURES
Your Radio Shack
Your CB has the following features:
LCD Digital Display ??? lets you see the channel number you select, incoming and outgoing signal strength, and the selected mode (such as Weather, Emergency, etc.)
PLL
er ??? provides highly accurate and stable tuning.
Two Ceramic Filters ??? provide superior selectivity and freedom from adjacent channel interference.
Hysteresis Squelch Circuit ??? compensates for fading signals and eliminates signal chopping during reception.
Automatic Noise Limiting (ANL) Circuit ??? reduc- es noise caused by nearby electrical equipment such as motors or automotive ignition systems.
Emergency Channel 9 Switch ??? lets you quickly switch to Channel 9 so you can report or monitor emergency situations.
?? 1995 Tandy Corporation.
All Rights Reserved.
Radio Shack is a registered trademark used by Tandy Corporation.
2
High/Low Power Button ??? lets you save power by selecting a suitable transmitting power for long or short distances.
For your records, we recommend you record your CB???s serial number here. The number is located on the CB???s back panel.
Serial Number _____________________
FCC INFORMATION
The Federal Communications Commission (FCC) does not require you to have a license to operate this CB. However, you must know Part 95 of FCC Rules. It explains the proper operation of a Class D citizen???s band transceiver. We enclosed a copy of Part 95 with your CB.
Warning: Do not open the CB to make any internal adjustments. A CB is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the unit to exceed these limitations.
Any adjustments to a CB must be made by a quali- fied technician using the proper test equipment.
To be safe and sure:
???Never open your CB???s case.
???Never change or replace anything in your CB.
Your CB might cause TV or radio interference even when it is operating properly. To determine whether your CB is causing the interference, turn it off. If the interference goes away, your CB is causing it. Try to eliminate the interference by:
???Moving your CB away from the receiver
???Contacting a radio/TV technician or your local Radio Shack store for help
If you cannot eliminate the interference, the FCC re- quires that you stop using your CB.
This device complies with Part 95 of FCC Rules. Op- eration is subject to the following two conditions:
3
1.This device must not cause harmful interfer- ence.
2.This device must accept any interference re- ceived, including interference that may cause undesired operation.
4
PREPARATION
CONNECTING POWER
You can power your transceiver from any of three sources:
???Internal batteries (not supplied)
???Vehicle battery power (using an optional DC cig- arette lighter power cord)
???Standard AC power (using an optional DC power supply)
Note: Connecting a DC power cord automatically disconnects internal batteries.
Using Internal Batteries
You can power your transceiver with nine AA batter- ies. For the longest operation and best performance, we recommend alkaline batteries (such as Cat. No.
Follow these steps to install or replace batteries.
1.If the transceiver is on, turn VOLUME/OFF coun- terclockwise until it clicks to turn it off.
2.Remove the battery compartment cover by slid- ing it in the direction of the arrow.
illustration
3.Remove any old batteries from the compart- ment.
Cautions:
???Always dispose of old batteries promptly and properly.
5
???Never leave dead, old, or weak non- rechargeable batteries in the transceiver. They can leak chemicals and corrode or dam- age electronic circuits.
???Do not expose batteries to extreme heat or fire. They might explode and cause personal injury or damage equipment.
4.Position the NI/AL switch to match the battery type.
???NI: for rechargeable
???AL: for standard or alkaline batteries.
illustration
5.Install nine fresh
illustration
Cautions:
???Improper installation (incorrect polarity) might damage the transceiver.
???Use only fresh batteries of the required size and type. Never mix new and old batteries or rechargeable and
6
???If you do not plan to use batteries in the trans- ceiver for a month or more, remove the bat- teries. This protects the transceiver from possible battery leakage.
6.Replace the cover.
When BATT (battery low) appears on the display, re- place or recharge the batteries.
Using Vehicle Battery Power
You can power your transceiver from your vehicle???s cigarette lighter socket with an optional DC cigarette lighter power cord (such as Cat. No.
Cautions:
???You must use a DC power cord that supplies 12 volts and delivers at least 2.5 amps. Its center tip must be set to positive, and it must have a plug that properly fits your transceiver???s DC13.8V CHARGE jack. The recommended power cord meets these requirements. Using a power cord that does not meet these specifications could damage the transceiver or the power cord.
???To protect your vehicle???s electrical system, always plug the power cord into the transceiver before you plug it into your vehicle???s cigarette lighter socket. Always unplug the power cord from the vehicle???s cigarette lighter socket before you unplug it from the transceiver.
illustration
1.Insert the power cord???s barrel plug into the trans- ceiver???s DC13.8V CHARGE jack.
2.Plug the other end of the cord into your vehicle???s cigarette lighter socket.
7
Notes:
???If you installed rechargeable
???If the transceiver does not operate when you use the power cord, unplug the cord from the cigarette lighter socket and clean the socket to remove ashes and debris. If it still does not operate properly, check the
Using Standard AC Power
You can operate the transceiver from AC power us- ing a
Cautions:
???You must use a DC power cord that supplies 12 volts and delivers at least 2.5 amps. Its center tip must be set to positive, and it must have a plug that properly fits your transceiver???s DC13.8V CHARGE jack. The recommended power cord meets these requirements. Using a power cord that does not meet these specifications could damage the transceiver or the power cord.
???Be sure you connect the DC power cord to the transceiver before you connect it to the power supply. Then disconnect the power cord from the power supply before you disconnect it from the transceiver.
Note: Most
8
Follow these steps to power the transceiver from AC power.
1.Using the
2.Insert the power cord???s barrel plug into the trans- ceiver???s DC13.8V CHARGE jack.
Note: If you installed rechargeable
3.Insert the cigarette lighter plug on the DC power cord into the cigarette lighter accessory outlet.
4.Connect the DC power supply to a standard AC outlet.
9
CHARGING
BATTERIES
The transceiver has a
Warning: Do not connect a power cord to the trans- ceiver???s DC13.8V CHARGE jack if you installed
It takes about 16 to 18 hours to recharge batteries that are fully discharged.
Notes:
???
???To prevent permanent
???Do not overcharge batteries. Overcharging can severely reduce the battery???s useful life.
Important: At the end of a rechargeable battery???s useful life, it must be recycled or disposed of proper- ly. Contact your local, county, or state hazardous waste management authorities for information on re- cycling or disposal programs in your area. Some op- tions that might be available are: municipal
10
CONNECTING AN ANTENNA
Your transceiver comes with a flexible rubber anten- na that is ideal for most applications. However, the transceiver???s BNC antenna connector makes it easy to connect other types of antennas. Your local Radio Shack store sells a wide variety of antennas. Choose the one that best meets your needs.
Follow these steps to connect the supplied antenna.
illustration
1.Position the antenna???s BNC connector over the antenna jack on the transceiver.
2.Slip the slot in the antenna connector over the antenna jack???s tab on top of the transceiver.
3.Press down and turn the antenna???s connector clockwise until it locks into place.
To use a mobile or
Warning: Use extreme caution when installing or re- moving an outdoor antenna. If the antenna starts to fall, let it go! It could contact overhead power lines. If the antenna touches a power line, contact with the antenna, mast, cable, or guy wires can cause elec- trocution and death! Call the power company to re- move the antenna. Do not attempt to remove the antenna yourself.
11
USING AN EXTERNAL SPEAKER
In a noisy area, an external speaker (such as Cat. No.
illustration
USING AN EXTERNAL SPEAKER/
MICROPHONE
You can use an external speaker/microphone (such as Cat. No.
illustration
12
USING THE WRIST STRAP
You can use the supplied wrist strap to keep the transceiver accessible. Hook the strap???s connecting ring to the tab, as shown. Then simply slip the strap over your hand.
illustration
USING THE BELT CLIP
Use the supplied belt clip to make the transceiver easier to take with you. Use the two supplied screws to attach the belt clip to the transceiver. Slide the belt clip over your belt or waistband.
illustration
13
OPERATION
Before you use your transceiver, you should know how to use it effectively and courteously. ???Operation- al Hints??? contains information that will help you get more enjoyment from your transceiver.
RECEIVING TRANSMISSIONS
AND ADJUSTING SQUELCH
1. Turn SQUELCH fully counterclockwise.
illustration
2.Rotate VOLUME clockwise until it clicks to turn on the power. A channel number appears on the display.
illustration
3.Press CHANNEL s or t to select the desired chan- nel.
illustration
Note: If you press CHANNEL s when you are tuned to Channel 40, the channel selector returns to Channel 1. If you press CHANNEL t when you are tuned to Channel 1, the channel selector returns to Channel 40.
14
4.Adjust VOLUME to a comfortable listening level.
5.To cut out background noise between transmis- sions, wait until there is no signal on the chan- nel, then slowly turn SQUELCH clockwise until the background noise stops.
Note: Do not turn SQUELCH too far clockwise because you might cut out weak signals, too.
6.To turn off the transceiver, turn VOLUME counter- clockwise until you hear it click.
TRANSMITTING
We recommend you try receiving transmissions be- fore you try to transmit.
Follow these steps to transmit.
1.Press and hold the talk button. TX appears on the display, and the signal meter on the display shows the output level. Hold the transceiver about
illustration
2.When you finish transmitting, release the talk button.
15
3.If you are transmitting to nearby units, press H/L to set the output power to low output power, if necessary. LOW appears on the display.
illustration
If the other transceiver is farther away or the receiving person complains of noise, press H/L again to set it to high output power. LOW disap- pears from the display.
4.To turn off the transceiver, turn VOLUME counter- clockwise until you hear it click.
TURNING ON/OFF THE LIGHT
Press LIGHT to turn on and off the display???s light. If you do not turn the light off manually, the light auto- matically shuts off in 5 seconds.
illustration
16
LOCKING THE FUNCTIONS
Use the KEY LOCK switch to lock the transceiver???s functions (except the talk button and LIGHT) to pre- vent accidental program changes. Press KEY LOCK so LOC appears on the display.
illustration
To release the lock, press KEY LOCK again. LOC disappears from the display.
USING CHANNEL 9
For emergency call monitoring or transmitting on Channel 9, just press
illustration
Important! Channel 9 is reserved for motorist assis- tance and for reporting emergency information about accidents, hazardous road conditions, and so on. Al- ways give emergency messages priority on Channel 9.
To release the transceiver from Channel 9, press CH- 9 again. The previously selected channel number ap- pears on the display.
Note: The KEY LOCK, WEATHER, and CHANNEL but- tons do not work when
17
LISTENING TO THE WEATHER
BAND
The FCC (Federal Communications Commission) has allocated 11 channels for use by the National Oceanographic and Atmospheric Administration (NOAA). NOAA broadcasts your local forecast and regional weather information on one or more of these channels in your area. We have preprogrammed your CB with 10 of the U.S frequencies used by NOAA. See ???Channel Assignments.???
To select a weather broadcast, press WEATHER then press CHANNEL s or t to choose between the 10 fre- quencies. WX appears on the display.
illustration
Press WEATHER again to return to normal CB opera- tion.
Note: The H/L and
18
OPERATIONAL HINTS
Like most activities, CB radio has its customs and courtesies. The following tips will help you get the most enjoyment from your transceiver.
COMMON USES FOR A CB
Business Uses
???Truck drivers and delivery personnel can learn road and traffic conditions and get assistance in locating destinations. A CB is also good com- pany on those ???long hauls.???
???On construction crews, a CB quickly pays for itself when you are calling for additional materi- als or coordinating the activities of different work crews.
???For security officers, a CB is more than a conve- nience ??? it is a must for both safety and effi- ciency.
Personal Uses
???Keep in touch with home while driving to work, to the store, or to a social activity. Let your family know you are tied up in traffic or that you will stop by the store on the way home.
???If you are a
???Contact friends or neighbors ??? find out ???what???s happening??? or plan a
???Ever have car trouble or run out of gas on the highway? What an assurance it is to be able to call for assistance!
???Camping, fishing, and other sports are more fun with a CB. Locate a buddy or find out ???what???s cooking??? back at camp.
19
TRANSMISSION COURTESY
???Wait for a pause in someone else???s transmission before you ask for a break.
???If you do not receive an answer to your call after a second attempt, sign off and wait several min- utes before trying again.
???Do not hold down the talk button when you are not talking. (This is called dead keying.)
???Assist callers with directions, information about road conditions, and any other reasonable requests.
MAXIMUM RANGE
The maximum range and quality of CB transceiver transmissions vary depending on the following condi- tions:
???The type and quality of antenna used
???The height of the antenna???s mounting location ??? the higher the antenna, the better the signal???s range
???The surrounding terrain ??? mountains and tall buildings limit the range
???Weather conditions
???The number of nearby CBs operating on the same channel
Note: Your transceiver???s transmission range is gen- erally
USING COMMON
Citizen???s band operators and CB users have largely adopted the
20
This table lists codes adopted by the Associated Public Safety Communications Officers (APCO).
21
CHANNEL ASSIGNMENTS
Your transceiver receives and transmits on the 40 channels listed here.
22
In addition, your transceiver is programmed with the following weather service channels:
23
CARE AND MAINTENANCE
Your Radio Shack
???Keep the CB dry. If it gets wet, wipe it dry imme- diately. Liquids can contain minerals that can corrode the electronic circuits.
???Use and store the CB only in normal tempera- ture environments. Temperature extremes can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.
???Handle the CB gently and carefully. Dropping it can damage circuit boards and cases and can cause the CB to work improperly.
???Keep the CB away from dust and dirt, which can cause premature wear of parts.
???Wipe the CB with a damp cloth occasionally to keep it looking new. Do not use harsh chemi- cals, cleaning solvents, or strong detergents to clean the CB.
Modifying or tampering with the CB???s internal compo- nents can cause a malfunction and might invalidate the CB???s warranty, and void your FCC authorization to operate it. If your CB is not performing as it should, take it to your local Radio Shack store for assistance.
24
SPECIFICATIONS
Note: The transceiver draws an additional 800 mA when charging
Note: The transceiver draws an additional 800 mA when charging
Specifications are typical; individual units might vary. Specifications are subject to change and improve- ment without notice.
25
NOTES
26
27
RADIO SHACK LIMITED WARRANTY
This product is warranted against defects for 90 days from date of purchase from Radio Shack company- owned stores and authorized Radio Shack franchisees and dealers. Within this period, we will repair it without charge for parts and labor. Simply bring your Radio Shack sales slip as proof of purchase date to any Radio Shack store. Warranty does not cover transportation costs. Nor does it cover a product subjected to misuse or accidental damage.
EXCEPT AS PROVIDED HEREIN, RADIO SHACK
MAKES NO EXPRESS WARRANTIES AND ANY
IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE DURATION OF THE WRITTEN LIMITED WAR- RANTIES CONTAINED HEREIN. Some states do not permit limitation or exclusion of implied warranties; there- fore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102