Your thermometer shows the current time, time zone, and day of week in English, Spanish, or French under normal mode. The time is automatically updated by the US Atomic Clock in Boulder, Colorado unless you disable this feature. Signals are collected by the thermometer when it is within 932 miles (1500 km) of a signal.
Initial reception takes 2-10 minutes, and is initiated when you ???rst set up the unit, and whenever you press RESET. The following icons display in the clock area based on your signal strength.
If you cannot receive Atomic Clock signals, press and hold ZONE for 2 seconds until the signal icon disappears. This turns the atomic clock off. Then, manually set the clock.
To force a manual search for Atomic Clock signals, press and hold e for 2 seconds until a beep sounds and the signal icon displays. If no signal is found, check the batteries.
% indicates the Atomic Clock feature is on. No icon indicates it is off.
Note: When you use the Atomic Clock function, press ZONE ???rst to choose your corresponding time zone.
set your clock
1.Open the battery compartment.
2.Press ZONE repeatedly to display the desired Time Zone: (P) Paci???c, (M) Mountain, (C) Central, or (E) Eastern.
3.Close the battery compartment.
4.Press and hold MODE for 2 seconds until a beep sounds. The Clock Area will blink.
5.Press MODE repeatedly to select the hour, minute, year, month, day and language. Press or hold e or d to change the setting. Press MODE to con???rm.
???When you set your clock, the display returns to normal mode if no button is pressed within 60 seconds.
???AM/PM appears for morning and afternoon time.
???The language options are (E) English, (F) French, and (S) Spanish.
Press MODE repeatedly to toggle between clock with seconds, clock with weekday, and calendar.
This product is equipped with a 2-minute crescendo alarm and 8-minute snooze. Press 3. The alarm time and on/off status displays in the clock area.
set your alarm
???LLL or HHH appears when the temperature is out of range.
???Place the sensor out of direct sunlight and moisture.
???Do not place the sensor more than 100 feet (30.5 meters) from the thermometer.
???Position the sensor facing the thermometer, minimizing obstructions such as doors, walls, and furniture. Place it away from metallic or electronic objects.
???Position the sensor close to the thermometer during cold winter months, as below-freezing temperatures may affect battery performance and signal transmission.
???If you still do not receive a signal, check the batteries, obstructions, and remote unit location.
???Signals from household devices, such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. This is normal and does not affect general product performance. The reception will resume once the interference ends.
???If the unit???s performance fails due to low temperature, the unit will resume proper functioning as the temperature rises to within the normal temperature range.
care
Clean your thermometer and sensor with a slightly damp cloth and alcohol-free mild detergent.
safety
???Never immerse your thermometer and sensor in water. This can cause electrical shock and can damage the units.
???Do not subject the thermometer to extreme force, shock, or temperatures.
???Do not tamper with the internal components.
???Do not scratch the LCD display.
???Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product. The technical specification of this product and contents of this user guide are subject to change without notice.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
???Reorient or relocate the receiving antenna.
???Increase the separation between the equipment and receiver.
???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult your local RadioShack store or an experienced radio/TV technician for help.
If you cannot eliminate the interference, the FCC requires that you stop using your thermometer. Changes or modi??? cations not expressly approved by RadioShack may cause interference and void the user???s authority to operate the equipment.
