FCC STATEMENT

This phone is Hearing Aid compatible.

Your phone complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number and the REN to your telephone company. Both numbers are on the bottom of the phone.

Note: You must not connect your phone to:

???coin-operated systems

???party-line systems

???most electronic key telephone systems

We have designed your phone to conform to federal regulations, and you can connect it to most telephone lines. However, each phone (and each device, such as an answering ma- chine) that you connect to the telephone line draws power from the telephone line. We re- fer to this power draw as the device's ringer equivalence number, or REN on the bottom of your phone.

If you use more than one phone or other de- vice on the line, add up all of the RENs. If the total is more than five (three in rural areas), your telephones might not ring. If ringer oper- ation is impaired, remove a device from the line.

In the unlikely event that your phone causes problems on the phone line, the phone com- pany can temporarily discontinue your ser- vice. If this happens, the phone company attempts to notify you in advance. If advance notice is not practical, the phone company notifies you as soon as possible and advises you of your right to file a complaint with the FCC.

Also, the phone company can make changes to its lines, equipment, operations, or proce- dures that could affect the operation of this telephone. The telephone company notifies you of these changes in advance, so you can take the necessary steps to prevent interrup- tion of your telephone service.

THE FCC WANTS YOU TO

KNOW

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour- aged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

?? Installation

SELECTING A LOCATION

You can place the phone on a desk or table, on a standard wall plate or mount it directly on a wall. Select a location that is:

???near a telephone line jack

???out of the way of normal activities

???away from electrical machinery, electri- cal appliances, metal walls, filing cabi- nets, wireless intercoms, security alarms, and room monitors

Your telephone connects directly to a modu- lar telephone line jack. If your telephone wir- ing does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store), or have the telephone company up- date the wiring for you. You must use com- patible modular jacks that are compliant with Part 68 of FCC Rules. The telephone cord and modular plug provided is Part 68 compli- ant for connecting to the telephone company network.

Note: The USOC number of the single-line jack to be installed is RJ11C (or RJ11W for a wall plate jack). The USOC number for a two-line jack is RJ14C (or RJ14W for a wall plate).

MOUNTING THE PHONE

On a Desktop

1.Plug one end of the supplied long modu- lar cord into the modular jack on the base???s bottom.

2.Route the phone cord through the groove on the base???s bottom. Secure the cord under the tabs along the groove.

3.Plug the other end of the cord into a modular phone jack.

On a Wall Plate

1.Plug one end of the supplied short mod- ular cord into the modular jack on the back of the phone.

2.Route the phone cord through the first tab, then into the groove leading to the rectangular space. Secure the cord with the tabs.

3.Plug the other end of the cord into a wall plate with a modular phone jack. Press any excess cord into the rectangular space on the bottom of the system to keep it out of the way.

4.Fit the wall plate studs into the keyhole slots on the bottom of the phone, then slide the base down to secure it.

1/4-inch (6.3 mm) from the wall. (Be sure to use screws with heads that fit into the keyhole slots on the base???s bottom).

2.Plug one end of the supplied long modu- lar cord into the modular jack on the base???s bottom.

3.Route the phone cord through the groove on the base???s bottom, securing the cord under the tabs.

4.Fit the heads of the screw into the bot- tom???s keyhole slots, then slide the base down until it is secure.

5.Plug the other end of the cord into a modular phone jack.

line???s battery status when the phone is off- hook.

If Line 1 is in use, BATT LOW lights when no battery is installed for Line 1 or when Line 1???s batteries are low. When this happens, re- place the batteries.

Note: The BATT LOW indicator remains off when batteries are sufficient.

Warning: Dispose of old batteries promptly and properly. Do not burn or bury them.

Caution: If you do not plan to use the phone for a month or more, remove the batteries. Batteries can leak chemicals that can de- stroy electronic parts.

INSTALLING THE BATTERY

Your phone requires four AA batteries (not supplied) to power the LINE indicators. For the best performance and longest life, we recommend RadioShack alkaline batteries.

Cautions:

???Use only fresh batteries of the required size and recommended type.

???Do not mix old and new batteries, or dif- ferent types of batteries.

Follow these steps to install batteries.

1.Use a flat-blade screwdriver to lift up the battery compartment cover, then remove the cover.

2.Place the batteries in the compartment as indicated by the polarity symbols (+ and ???) marked inside. Be sure each line compartment has two batteries.

3.Replace and snap the cover into place.

Each LINE indicator requires two batteries for power. The BATT LOW indicator shows a

CONNECTING THE

HANDSET

To connect the handset to the phone???s base, plug one end of the supplied coiled cord into the modular jack on the handset.

Plug the other end into the jack on the side of the base.

Place the handset in the cradle.

Your local RadioShack store sells a variety of longer coiled handset cords, which are useful when you mount the system on a wall.

?? Preparation

SETTING THE DIALING

MODE

Set PULSE/TONE on the handset for the type of service you have. If you are not sure which type you have, follow these steps to perform

atest.

1.Lift the handset and set PULSE/TONE to TONE. When you hear the dial tone, press any number other than 0.

Note: If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not press the access code either.

# does not function when PULSE/TONE is set to PULSE.

2.If the dial tone stops, you have touch- tone service. Leave PULSE/TONE set to

TONE.

If the dial tone continues, you have pulse service. Set PULSE/TONE to

PULSE.

SETTING THE RINGER

To adjust the ringer volume, set each line???s RINGER to HI, LO or OFF. With the ringer off, you can still answer calls if you hear an ex- tension phone ring or see one of the phone???s LINE indicators flash.

TURNING OFF THE LINE 2

INDICATOR

If you want to install the phone as a one-line phone, you can turn off the LINE 2 indicator by removing the batteries for Line 2.

CHECKING THE LINE

STATUS INDICATORS

You can check the status of each line by glancing at the line status indicator.

?? Operation

VOLUME ??? Set to LO to hear a medium volume through the handset or to HI for a louder handset volume.

FLASH ??? Use to perform the switchhook operation for special services, such as Call Waiting.

For example, if you have Call Waiting, press FLASH to take an incoming call without disconnecting the current call. Press FLASH again to return to the first call.

Notes:

If you do not have special phone services, pressing FLASH might disconnect the current call.

When CONF is pressed, FLASH has no function

REDIAL ??? To dial the last num- ber dialed, lift the handset. When you hear the dial tone, press REDIAL. The phone dials the last number dialed.

RESET ??? At the end of a call, you can make your next call without placing the handset in the cradle. Press RESET to hang up the cur- rent call, then dial the next number. Note: When CONF is pressed, RE- SET has no function

LINE 1 and LINE 2 ??? Press the line button to se- lect a line, then lift the handset and dial the number. When you receive a call, that line???s indicator flashes rapidly until the line stops ringing. To answer the call, press the corresponding line button (LINE 1 or LINE 2), then lift the handset.

To end a call, hang up the handset.

HOLD ??? Press to place a call on hold. The line indicator flashes slowly. To return to the call, press its line button or pick up a parallel phone.

Note: Pressing another line button without pressing HOLD disconnects the current call.

USING THE DATA PORT

The phone is equipped with an extra phone jack that allows you to connect a communi- cation device (a computer modem, answer- ing machine, or fax machine) to Line 2. Connect a line cord (not supplied) from the communication device to DATA on the back of the phone.

Note: You cannot use Line 2 while a comput- er modem or fax machine is connected to DATA and in use. Line 1 still functions nor- mally. When you are finished using the mo- dem or fax machine, Line 2 becomes available again.

The USOC number of the data jack to be in- stalled is RJ11.

SWITCHING BETWEEN

LINES

Making a Call on Another Line

1.Press HOLD to place the first call on hold.

2.Press the LINE not in use, then dial the desired number.

3.Press the first call???s LINE at any time to return to the first call.

Answering a Call on Another Line

1.Press HOLD to place the first call on hold.

2.Press the flashing LINE to answer the incoming call.

3.To switch back to the first call, press HOLD to place your current call on hold.

4.Press the other LINE to return to the first call.

MAKING A CONFERENCE

CALL

1.Make or answer a call.

2.Press HOLD, then make or answer a call on another line.

3.When the second call is connected, press CONF. The lines are immediately connected.

4.To end the conference call, hang up. Both parties are disconnected, or you can press a LINE if you wish to continue with the call on that line. The party on the other line is disconnected.

?? Memory Operation

The phone has two types of memory ??? prior- ity and standard ??? that let you store and dial up to 13 phone numbers. You can store up to 3 phone numbers (up to 16 digits each) in priority memory and dial them by pressing a single button. You can store up to 10 phone numbers (up to 16 digits each) in standard memory and dial those numbers by pressing two buttons.

DIALING A STORED

NUMBER

To dial a phone number stored in a priority memory location, simply press that number???s priority memory (M1, M2, or M3).

To dial a phone number stored in a standard memory location, press MEMORY then the desired memory number (0???9).

STORING A NUMBER IN

MEMORY

With the phone off the hook, press STORE. Enter the phone number you want to store.

To store the number in one of the priority memory locations, press STORE again, then press M1, M2, or M3, then hang up the phone.

To store the number in one of the standard memory locations, press STORE again, then press one of the memory locations (0???9). Hang up the phone.

Notes:

???For security purposes, we recommend that you do not store private numbers, such as personal identification numbers or passwords.

???You cannot erase a number in memory, but you can replace it by storing a new one in its place.

???Write the memory location number and the name associated with that number on the system???s memory dialing card. Remove the card???s cover by lifting its edge.

TESTING STORED

EMERGENCY NUMBERS

If you store the number of an emergency ser- vice (police department, fire department, am- bulance) and you choose to test the stored number, remain on the line to explain the reason for your call. Make the test call during the late evening or early morning hours to avoid periods of peak demand.

CHAIN-DIALING SPECIAL

SERVICE NUMBERS

For quick recall of numbers for special ser- vices (such as alternate long-distance or bank-by-phone), you can store each group of numbers in its own memory location.

When calling special services, dial the ser- vice???s main number first. At the appropriate place in the call, press the appropriate mem- ory number for the additional numbers you want to send.