Radio_Shack_DVD_VCR_Combo_DVD_

Please read before using this unit.

DVD/CD Player with Video Cassette Recorder

INSTRUCCIONES EN ESPA??OL INCLUIDAS.

Supplied Accessory

Precautions

??2006. RadioShack ?? Corporation.

Table of Contents

Precautions

Laser Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

??? Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Avoid the Hazards of Electrical Shock and Fire . . . . . . . . . . . . . . 4 Moisture Condensation Warning . . . . . . . . . . . . . . . . . . . . . . . . . 4 Notice for Progressive Scan Outputs . . . . . . . . . . . . . . . . . . . . . 4 About Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Symbols Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

??? About the Video Cassettes and Discs . . . . . . . . . . . . . . . . . . . 5

Playable Video Cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unplayable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setup

??? Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Hint for Cable Box or Satellite Box . . . . . . . . . . . . . . . . . . . . . . . 6 Connection to an Audio System . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front & Rear Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

??? Preparation for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turn on the Unit for the First Time . . . . . . . . . . . . . . . . . . . . . . . 8 Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

??? Function Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VCR/DVD Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installing the Batteries for the Remote Control . . . . . . . . . . . . . 10

VCR Functions

??? Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

??? Other Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Time Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Auto Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

??? Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Recording & OTR (One Touch Recording) . . . . . . . . . . . . . . . . 12 Timer Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Hints for OTR and Timer Recording . . . . . . . . . . . . . . . . . . . . . 13 Copying a Video Tape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

??? MTS System (Multi-Channel Television Sound) . . . . . . . . . . . 14

When You Receive or Record a Program Broadcast in MTS . . . 14 When You Play Back a Tape Recorded in Hi-Fi Stereo . . . . . . . 14

DVD Functions

??? Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

??? On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

??? Search Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Track Search / Title/Chapter Search / Time Search . . . . . . . . . 17

??? Marker Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 ??? Repeat / Random / Programmed Playback . . . . . . . . . . . . . . 18

Repeat Playback / Repeat A-B Playback /

Random Playback / Programmed Playback. . . . . . . . . . . . . . . . 18

??? Special Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Subtitle Language / Audio Language / Camera Angle /

Black Level Setting / Stereo Sound Mode / Virtual Surround . . . . . . . 19

??? DVD Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

LANGUAGE Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 DISPLAY Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 AUDIO Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 PARENTAL Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 OTHERS Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Reset to the Default Setting (Except for PARENTAL Setting) . . . 23

Information

??? Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

??? Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

??? Language List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

??? Limited Ninety-Day Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 24

Espa??ol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Quick Use Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Information DVD Functions VCR Functions Setup

Connect

From TV

RF cable (supplied)

5 Please refer to ???Connections??? on page 6.

Espa??ol

817-415-3200

Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to pos- sible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

Phone

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1)Reorient or relocate the receiving antenna.

2)Increase the separation between the equipment and receiver.

3)Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4)Consult with your local RadioShack store or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil num??rique de la classe B est conforme ?? la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ??VITER LES CHOC ??LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU???AU FOND.

A NOTE ABOUT RECYCLING

This product???s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

Make your contribution to the environment!!!

???Used up batteries do not belong in the dust bin.

???You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.

???Do not throw away batteries. Dispose of them properly.

IMPORTANT SAFEGUARDS

1.Read Instructions - All the safety and operating instruc- tions should be read before the appliance is operated.

2.Retain Instructions- The safety and operating instructions should be retained for future reference.

3.Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions - All operating and use instructions should be followed.

5.Cleaning - Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the refer- ence to unplugging the appliance in the cleaning descrip- tion otherwise required in item 5.

6.Attachments - Do not use attachments not recommend- ed by the video product manufacturer as they may cause hazards.

7.Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swim- ming pool, and the like.

8.Accessories - Do not place this video product on an unsta- ble cart, stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult, and seri- ous damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufactur- er, or sold with the video product. Any mounting of the appliance should follow the manufactur-

er's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appli- ance and cart combination to overturn.

9.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these open- ings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10.Power Sources - This video product should be operated only from the type of power source indicated on the mark- ing label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

11.Grounding or Polarization - This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety fea- ture. If you are unable to insert the plug fully into the out- let, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12.Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep- tacles, and the point where they exit from the appliance.

13.Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to

proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna- discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges.

15.Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.

18.Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified ser- vice personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the video product.

c.If the video product has been exposed to rain or water.

d.If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.

e.If the video product has been dropped or damaged in any way.

f.When the video product exhibits a distinct change in per- formance this indicates a need for service.

20.Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21.Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to per- form safety checks to determine that the video product is in proper operating condition.

22.Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Precautions

Installation Location

For safety and optimum performance of this unit:

???Do not stand the unit up vertically. Install the unit in a horizontal and stable position. Do not place any- thing directly on top of the unit. Do not place the unit directly on top of the TV.

???Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations sub- ject to strong vibration or strong magnetic fields.

???Be sure to remove a disc and unplug the AC power cord from the outlet before carrying the unit.

Avoid the Hazards of Electrical Shock and Fire

???Do not handle the power cord with wet hands.

???Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.

???If, by accident, water is spilled on this unit, unplug the power cord immediately and take the unit to your local RadioShack ?? store for servicing.

???Do not put your fingers or objects into the unit cas- sette holder.

Moisture Condensation Warning

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours until its inside gets dry.

Notice for Progressive Scan Outputs

Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 525 progressive scan output, it is recommended that the user switch the connection to the ???standard definition??? output. If there are questions regarding your TV set compatibility with this 525p DVD player, please contact RadioShack store.

About Copyright

Unauthorized copying, broadcasting, public perfor- mance and lending of discs are prohibited.

This product incorporates copyright protection tech- nology that is protected by U.S. patents and other intellectual property rights. Use of this copyright pro- tection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Maintenance

SERVICING

???Please refer to relevant topics on the ???Troubleshooting Guide??? on page 23 before returning the product.

???If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-service- able parts inside. Turn off, unplug the power plug, and please consult with your local RadioShack store.

CLEANING THE CABINET

???Use a soft cloth slightly moistened with a mild deter- gent solution. Do not use a solution containing alco- hol, spirits, ammonia or abrasive.

CLEANING DISCS

???When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion.

???Do not use solvents such as benzine, thinner, com- mercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for ana- log records.

CLEANING THE DISC LENS

???If this unit still does not perform properly although you refer to the relevant sections and to ???Troubleshooting Guide??? in this Owner???s Manual, the laser optical pick- up unit may be dirty. Please consult with your local RadioShack store for inspection and cleaning of the laser optical pickup unit.

DISC HANDLING

???When you handle a disc, hold it by its edge and try not to touch the surface of the disc.

???Always store the disc in its protective case when it is not used.

AUTO HEAD CLEANING

???Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

???Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accu- mulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your unit may need to be cleaned.

1.Please visit your local RadioShack store and pur- chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob- lem, please consult with your local RadioShack store.

Hint

???Remember to read the instructions along with the video head cleaner before use.

???Clean video heads only when problems occur.

Symbols Used in This Manual

The following symbols appear in some head- ings in this manual.

:Description refers to playback or recording VCR of video cassette tapes.

:Description refers to playback of DVD- DVD-V Video discs.

:Description refers to playback of Audio CD CDs.

Note to CATV system installer

This reminder is provided to call the CATV system installer???s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in par- ticular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

Manufactured under license from Dolby Laboratories. ???Dolby??? and the double-D symbol are trademarks of Dolby Laboratories.

About the Video Cassettes and Discs

Playable Video Cassettes

Use only cassettes marked with this unit.

Playable Discs

is a trademark of DVD Format/Logo Licensing Corporation.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.

*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc???s producers.

*3: Discs recorded in the VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or spe- cial properties of discs.

*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not play them back. Even if they are played back, the sound or video quality will be compromised.

*7: You may play back the unfinalized DVD-RW/R disc recorded in the video format on our brand???s DVD recorder. However, depending on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth, etc.).

*9: If there is too much recording space left on a disc (the used portion is less than 55 mm across), it may not play back properly. *10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.

Unplayable Discs

??NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / DVD-Audio / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL / DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers

??On the following disc, the sound MAY NOT be heard.

Super Audio CD

NOTE: Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

??Any other discs without compatibility indications

Precautions

Setup

Connections

Please refer to ???Basic TV Connection??? on the front page before you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.

???If ???VCR??? light does not appear on the display of this unit, press [VCR/TV] on the remote control.

4) Press [PLAY B] once.

5) After a few seconds, press and hold [PLAY B] on the unit for 3 seconds.

???The RF output channel will change to channel 4 from channel 3 and you will see a playback picture. In this case, ???ch04??? will appears on the front panel.

???When a picture does not appear on the TV screen, repeat step 4).

6) Press [STOP C] to stop playback.

Hint

???The RF output channel does not change when you adjust tracking during playback. In case RF output channel changes, you can easily switch it back just start the playback again then press and hold [PLAY B] on the unit for 3 seconds.

Setup

Hint for Cable Box or Satellite Box

Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the unit. You can view or record ONLY the channels you have selected on the cable box or the satellite box.

???While you are recording, only the recorded channel can be viewed.

To select channels of the cable box or satellite box

1)Turn on the unit by pressing [POWER], then press [VCR/TV].The ???POWER??? and ???VCR??? lights on the front panel will appear, then press [SKIP/CH. G/K H/L] to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).

???If you use the channel 4, you need to change the unit???s RF output to channel 4. Refer to ???RF Output Channel???.

2)At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).

3)On the cable box or satellite box, select the channel you want to view or record.

Connection to an Audio System

Audio cable (supplied)

Hint

??? Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

Select this connection when you want to change channels on the VCR/DVD. With this connection, you may watch one channel while recording another.

??? You may not view or record a scrambled channel.

To select channels of the cable box or satellite box

1)At the cable box or satellite box, select channel 3 or 4 (the same channel as the VCR/DVD???s RF output channel).

??? Refer to ???RF Output Channel???.

2)At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box.

3)Turn on the VCR/DVD by pressing [POWER], and then, press [VCR/TV]. The ???POWER??? and ???VCR??? lights on the front panel will appear. Then, select the channel you want to view or record.

To playback a tape

Follow the steps 1) to 2) above. Then, playback a tape.

??? Refer to ???Playback??? on page 11.

To view one channel while recording another

1)While you are recording on the VCR/DVD, press [VCR/TV] so that the ???VCR??? light disappears on the VCR/DVD.

2)At the cable box, select the channel you want to view.

* To complete these settings, refer to pages 20-21.

Hint

???The audio source on a disc in a Dolby Digital multi channel surround format cannot be recorded as digital sound by an MD or DAT deck.

???By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital multi channel surround sound as heard in the movie theaters.

???Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

Connection to a TV

Basic Audio

Video cable (supplied)

Hint

???Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due to the copy protection system.

???The COAXIAL, DVD AUDIO OUT, S-VIDEO OUT and COMPONENT VIDEO OUT jacks are only useful in DVD mode.

If your TV is compatible with 525p (480p) progressive scanning and you want to enjoy that high quality picture;

Set ???PROGRESSIVE??? to ???ON??? in the DISPLAY menu, so that the ???P.SCAN??? on the front panel display appears. Details are on page 21.

If your TV is not compatible with progressive scanning;

Use this unit in interlace mode. Make sure ???PROGRESSIVE??? is set to ???OFF??? and P.SCAN light on the front of the unit is off. Progressive scanning mode can be set to off either in the DISPLAY menu or by pressing and holding [PLAY B] on the front of the unit for more than 5 seconds. Details are on page 21.

After you have completed connections

???Press the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually near channel 0) for viewing the picture from this unit.

If the picture does not appear, also refer to the manual accompanying your TV.

Input modes for common TV brands (Example)

??? Listed below are inputs for common brand name TV???s.

Setup

Front & Rear Terminals

ANT-IN jack

Connect your antenna or cable box here.

VIDEO L - AUDIO - R

[Front

Panel]

ANT-OUT jack

Connect the supplied RF cable to the antenna input jack on your TV.

Preparation for Use

Turn on the Unit for the First Time

VCR

Turn on the TV and set it to channel 3.

???If channel 3 is already occupied for broadcasting, see???RF Output Channel??? section on page 6.

???If your antenna is connected to an antenna ampli- fier, the amplifier???s gain adjustment may need to be temporarily reduced in order for Auto-Setup to program all channels properly.

To Add or Delete Channels

1)Press [MENU] until the main menu appears.

2)Select ???CHANNEL SET UP??? by pressing [K/L]. Then, press [B].

3)Select ???MANUAL SET UP??? by pressing [K/L]. Then, press [B].

4)Enter the desired channel number by pressing [K/L] or

[SKIP/CH. G/K H/L].

5)Add or Delete it from memory by pressing [s/B] so that ???ADD??? or ???DELETE??? flashes on the TV screen accordingly.

Setup

ESPA??OL

Do you connect the cable from the cable box or the satellite box to the unit???s ANT-IN jack?

YES

Yes Press [MENU]

to exit.

??? Refer to ???Hint for Cable Box or

Satellite Box??? section on page 6. NO

6)Exit the Preset mode by pressing

[CLEAR/C.RESET].

To Preset the Channel Again

1)Press [MENU] until the main menu appears.

2)Select ???CHANNEL SET UP??? by pressing [K/L], then press [B].

3)Select ???AUTO SET UP??? by using [K/L], then press [B]. After scanning, the tuner stops on the lowest memorized channel.

To Change the On-Screen Language

1)Press [MENU] until the main menu appears.

2)Select ???LANGUAGE SELECT??? by pressing [K/L], then press [B].

3)Select ???ENGLISH??? , ???FRANCAIS??? or ???ESPA??OL??? by pressing [K/L] , then press

[CLEAR/C.RESET] to exit.

Hint

???If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].

???To add or delete channels in this unit, [SKIP/CH. G/K H/L] button works on the channel number memorized in this unit, [K/L] works on all.

Clock Setup

No Please wait for a few minutes.

After scanning...

VCR

???The tuner stops on the lowest memorized channel.

???You can select only the channels memorized in this unit by using [SKIP/CH. G/K H/L]

(or [CHANNEL K/L]).

???If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press [B] once again.

Hint

???Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Select a Channel

You can select a channel by using the Number buttons or

1MENU

- M E N U -

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

BCLOCK SET

LANGUAGE SELECT

AUDIO OUT

TV STEREO [ON]

SAP

???If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2).

Select ???AM??? or ???PM???.

8To exit the CLOCK SET screen

Hint

[SKIP/CH. G/K H/L].

Notes for using the Number buttons:

???When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press [1], [1], [7])

???You must precede single-digit chan- nel numbers with a zero (for example:

02, 03, 04 and so on).

Select the current month.

mark will disappear when you set VCR/DVD in DVD

Function Overview

Front Panel Display

Lights up when power is on.

No disc inserted

/ cannot read disc

Opening the tray

Closing the tray

Loading the disc

When a disc or tape is

???DVD: DVD disc

???CD: Audio CD

Setup

being played back

Lights up when the playback is

in still or slow mode.

Lights up when the inserted cassette is being played back.

VCRREC

Lights up when current time is P.M.

Works as a tape counter(hour,minute,second). Also displays a channel number,

tape speed, remaining time for OTR or current time.

* , and

mode. However, the function indicated by each mark is still working.

VCR/DVD Switching

Because this product is a combination of a VCR and a DVD player, you must select first which compo- nent you wish to operate with [OUTPUT].

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD OUTPUT light is lit.)

Hint

???Pressing only [OUTPUT] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

OUTPUT button

VCR Functions

VCR

Other Operations

Hint

???When a tape without record tab is inserted, the unit will start playback automatically.

???Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press

[SKIP/CH. G/K H/L] (or [CHANNEL K/L]).

To cue or review picture during playback (Picture Search)

Press [g / h]([F.FWD g] or [REW h] ).

???Press it again and the unit will search in super high speed (in the SLP mode only).

To freeze the picture on TV screen during play- back (Still mode)

Press [PAUSE k]. Each time you press the button, the picture will be forwarded by one frame.

???If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing

[SKIP/CH. G/K H/L] (or [CHANNEL K/L]).

???If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV if equipped.

Counter Reset

Press [CLEAR/C.RESET].

To play back in slow motion (Slow mode)

Press [SLOW] during playback or the still mode.

???If the noise bars appear on the TV screen, you can reduce it by pressing [SKIP/CH. G/K H/L](or

[CHANNEL K/L]).

Auto Rewind

When a tape reaches its end during playback, fast-for- ward or recording (except Timer Recording and One Touch Recording), the tape will automatically rewind to the beginning. After rewinding finishes, the unit will eject the tape.

Hint

???Still/Slow mode will be automati- cally canceled after 5 minutes to prevent damage to the tape and the video head.

???To return to play- back from the Picture Search/Still/ Slow mode, press [PLAY B].

Functions

Index Search

You can skip the program backward and forward by the Index Mark.

VCR

??? Insert a tape into this unit.

1 SEARCH

MODE

INDEX SEARCH

??? ???

Press once.

To rewind

To fast forward

After searching,

4PLAYB

Time Search

You can search backward and for- ward a specific length of time on a tape.

VCR

??? Insert a tape into this unit.

1 SEARCH

MODE

TIME SEARCH

??? : ??? ???

Press twice.

2Select the desired length of time for fast forwarding or

rewinding.

TIME SEARCH

2 : 5 0

0:01~ 9:59 (1 minute~9 hours and 59 minutes)

3 To rewind

To fast forward

After searching,

4PLAYB

???11 ???

Hint

???The Index Mark will be made automatically at the beginning of each recording.

???The time gap between Index Marks should be greater than 1 minute for SP mode, 2 minutes for LP mode and 3 minutes for SLP mode.

???Index Search and Time Search functions are not available during recording.

???Press [STOP C] to stop the search.

???If a tape ends during a search, your search will be canceled and the tape will rewind to the beginning.

VCR

5Select the desired start time

(hour).

Select the minute.

Select ???AM??? or ???PM???.

7Repeat the procedure in steps 5) and 6) to set the end time.

Select the desired channel.

???If you have connected the unit to a cable box or satellite box as the Connection on page 6, select the VCR to channel 3 or 4 (the RF output chan- nel of the VCR). Then, select the desired channel at the cable box or satellite box. Leave the cable box or satellite box on for timer recording.

Select the desired recording speed.

???To set another program after step 9), press [B]. Then, continue with step 2).

CLEAR/

C. RESET

appear in the front panel dis- play. In some occasions, how- ever, the VCR/DVD may be automatically turned off, instead of changing to the DVD mode after pressing

[SUBTITLE/T-SET].

???To use the VCR after Timer Recording finishes normally, press [SUBTITLE/T-SET].

Hint

???To go back one step, press [s] (during steps 3) to 9) ).

To Check, Correct or Cancel a Timer Program

1)Press [SUBTITLE/T-SET] then,

[VCR] on the remote control.

2)Select main menu by pressing [MENU].

3)Select ???TIMER PROGRAMMING??? by pressing [K/L]. Then, press [B].

4)Select the program number which you want to check by pressing [K/L]. The

details of the program you selected will appear on the TV screen.

???Go to the digit you want to change by pressing [s/B]. Then, enter cor- rect numbers by pressing [K/L].

???You may cancel the entire program by pressing [s] while the program number flashes.

5)Press [CLEAR/C.RESET] to exit.

6)Press [SUBTITLE/T-SET] to return to timer stand-by mode.

To cancel a Timer Recording in progress

Press [STOP/EJECT C/A] on the unit.

VCR Functions

Hints for OTR and Timer Recording

???Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode, then press [SUBTITLE/T-SET].

???If a tape is not in the unit or does not have the record tab, the light flashes and Timer Recording cannot be performed. Please insert a recordable tape.

???When Timer Recordings are set, the light will appear. To use the VCR as usual until the time for the recording, press [SUBTITLE/T-SET] so that the light disappears. Press [VCR/TV] to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual.

After an OTR and a Timer Recording has been set, this unit operates as follows:

???If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. Press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT] on the unit, then press [VCR] to activate the VCR function again.

???Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is pressed. ([OUTPUT] on the front panel and [VCR] on the remote control will not function.)

???To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT] on the unit, then press [VCR] to activate the VCR function again.

???The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after you canceled Timer

Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you operate.

???Once the unit switches to the DVD mode, all the VCR function will be unavailable. ??? ??? will not appear as long as the DVD is in use. All the DVD functions are available during OTR, timer standby mode and Timer Recording.

When an OTR or a Timer Recording is completed...

???If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically, and the light appears to indicate the unit is in the timer standby mode.

???The light flashes if there are no more Timer Recordings on standby.

???If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR function will be unavailable. The light will not appear as long as the DVD is in use. All the DVD functions are available during OTR, timer standby mode and Timer Recording.

???Press [STOP/EJECT C/A] on the front panel or [SUBTITLE/T-SET] on the remote control to use the VCR when the unit is off.

???Press [OUTPUT] on the front panel or [VCR] on the remote control to use the VCR when the unit is on. In case Timer Recording is in standby mode, press [STOP/EJECT C/A] on the front panel or [SUBTITLE/T-SET] on the remote control, and then press [OUTPUT] on the front panel or [VCR] on the remote control.

If you want to use the DVD function during a timer recording or while the light is on or blinking.

???Press [POWER] to turn on the VCR/DVD. Press [DVD] on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual.

Note (for Timer Recording) :

??? If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.

Functions VCR

Copying a Video Tape

Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.

1)Insert a pre-recorded tape into the playing VCR.

2)Insert a tape with its record tab into the recording unit.

3)Press [SPEED] on the remote control of the recording unit to select the desired recording speed (SP/SLP).

4)Select the ???L1???or ???L2??? position on the recording unit.

???To use the input jacks on the back of this unit, select ???L1??? position by pressing [0], [0], [1] on the remote control or

[CHANNEL K/L].

???To use the input jacks on the front of this unit, select ???L2??? position by pressing [0], [0], [2] on the remote control or

[CHANNEL K/L].

5)Press [REC/OTR] on the recording unit.

6)Begin playback of the tape in another source.

7)To stop recording, press [STOP/EJECT C/A] on the recording unit, then stop playback of the tape in another source.

Hint

??? For best results during dubbing, use the front panel controls whenever possible. The remote control might affect another source???s operation.

???Always use video-quality shielded cables with RCA-type connectors. Standard Audio cables are not recommended.

???You can use a video disc player, satellite receiver or other Audio/Video component with Audio/Video outputs.

??????L1??? or ???L2??? is found before the lowest memorized channel. (Example: CH02)

??????L2??? input jacks are on the front of this unit.

MTS System (Multi-Channel Television Sound)

When You Receive or Record a Program Broadcast in MTS

DVD Functions

Operations described after this section are mainly based on the remote control use. Some operations can be carried out on main unit.

Playback

Before: Turn on the TV, amplifier and any other components which are connected to this unit. Make sure the TV and audio receiver (commercially available) are set to the correct channel.

DVD menu

Some discs contain menus which allow you to customize DVD playback. Press [K / L / s / B] to select an item, then press [ENTER] (or [PLAY B]).

Calling up a Menu Screen during Playback

???Press [MENU] to call up the DVD menu.

???Press [TOP MENU] to call up the title menu.

Hint

???Menu operations may vary depending on the disc. Refer to the manual accompanying the disc for details.

Resume

DVD

DVD-V CD

Hint

???To cancel resume, press [STOP C] one more time during the Stop mode.

???The resume information stays on even when the power is turned off.

Paused and Step-by-Step Playback

DVD

DVD-V CD

Press [PAUSE k] during playback.

To continue playback, press [PLAY B].

DVD-V

The disc goes forward by one frame each time [PAUSE k] is pressed during the pause mode.

To continue playback, press [PLAY B].

Hint

???On DVDs, set ???STILL MODE??? to ???FIELD??? in the DISPLAY menu if pictures in the pause mode are blurred. (Refer to pages 20-21.)

Fast Forward/Reverse Search

DVD

DVD-V CD

Hint

???For DVDs, fast forward or reverse search speed is different depending on the disc. Approximate speed is 1(x2), 2(x8), 3(x20), 4(x50), 5(x100).

???For Audio CDs, approximate speed is 1(x2), 2(x8), 3(x30).

Slow Forward/Slow Reverse

DVD

Hint

???Slow forward or reverse speed is different depending on the disc. Approximate speed is 1(1/16), 2(1/8), 3(1/2).

???Set ???STILL MODE??? to ???FIELD??? in the DISPLAY menu if pictures in the slow playback mode are blurred. (Refer to pages 20-21.)

Zoom

DVD

DVD-V

1)Press [ZOOM] during playback.

2)Press [ZOOM] repeatedly to select the required zoom factor: x2, x4 or OFF.

3)Press [K / L / s / B] to slide the zoomed picture across the screen.

4)To exit zoom mode, press [ZOOM] to select OFF.

Hint

???Zooming function does not work while the disc menu is showing up.

???x4 zoom is not available on some discs.

???The picture may be distorted when you press [PAUSE F], [D] or [E] repeatedly in the zoom mode.

???In the zoom mode, it automatically changes x2(x4) to the zoomed position guide.

DVD Functions

On-Screen Display

You can check the information about the current disc by pressing [DISPLAY] on the remote control.

DVD

DVD-V

Functions DVD

DISPLAY

Elapsed time of the current chapter

CH(Chapter):

Current chapter number / Total chapters

Remaining time of the current title

Elapsed time of the current title

TT(Title):

Current title number / Total titles

Layer numbers, appears only when playing a two-layered disc

L0: Layer 0 is playing

L1: Layer 1 is playing

Current repeat setting appears only when the repeat setting is active

C: Chapter repeat / T: Title repeat / AB: A-B repeat

BIT RATE: The amount of audio and video data currently being read

???When you are playing a disc in PROGRAM or RANDOM mode,

PROGRAM (or RANDOM) will be displayed instead of 2 .

Search Function

Track Search

DVD

Using [SEARCH MODE]

1SEARCH

MODE

/29

7 8 9

0 +10

within 30 seconds

???For the disc with less than 10 tracks, press the track number directly.

???For discs with more than 10 but less than 99 tracks, to play a single-digit track, press [0] first, then the track number (e.g. for track 3, press [0], [3]). To play a double-digit track, press the track number.

???[+10] button can also bring the Track Search display, except for the disc with less than 10 tracks. For such a disc, track search can be done by just pressing the track number.

???For Audio CDs, Track Search is not avail- able for Programmed or Random Playback.

Title / Chapter Search

DVD

DVD-V

Using [SEARCH MODE]

PLAY

/12

Using [SKIP/CH. G/K H/L]

(If the disc has no chapters)

Hint

???Depending on the disc being played, this function can also be performed by directly entering the desired chapter number with the Number buttons. Refer to the manual accompanying the disc.

Time Search

DVD

DVD-V CD

Hint

???When there is no need to enter a number, ???0??? appears automatically.

For example, ???0: 0_: __??? appears in the Time Search display if the total time of the title or track is less than 10 minutes.

???Press [CLEAR/C.RESET] to erase the incorrect input at step 2).

Functions

Marker Setup

DVD

??? Playback will restart from the specific point which you set.

To exit the marker screen

RETURN

Hint

???The Marker display will disappear in about 30 seconds when there is no output.

???To clear a marker, select the marker to be cleared at step 2) in the section ???To set a marker??? or ???To return to the marker later??? and then press [CLEAR/C.RESET].

???Opening the disc tray or turning off the power will erase all markers.

???Selecting ???AC??? at step 2) in the section ???To set a marker??? or ???To return to the marker later??? will also erase all markers.

Repeat / Random / Programmed Playback

Repeat Playback

DVD

DVD-V CD

Repeat function is available only during playback.

Each time you press [REPEAT], repeat function changes as example below.

DVD-V

Repeat A-B Playback

DVD

DVD-V CD

PLAY

A-

A-B

At your desired starting point (A)

At your desired end point (B)

???Point B should be in the same title or track as point A.

Programmed Playback

DVD

You may determine the order in which tracks will play.

CHAPTER (current chapter repeat)

TITLE (current title repeat)

Hint

???To exit the sequence, press [A-B] so that OFF appears.

???To cancel Point A, press [CLEAR/C.RESET].

???This function does not work in the other repeat modes.

Random Playback

ENTER

??? Up to 99 tracks can be ordered.

???If eight or more tracks were in a program, use

[SKIP/CH. G/K H/L] to see all the tracks.

Functions DVD

ALL (entire disc repeat)

Hint

???Repeat setting (except ALL) will be cleared when moving to another title, chapter or track.

???Repeat playback are not available with all discs or during repeat A-B playback.

This function shuffles the playing order of tracks instead of playback in the sequence.

???To repeat the current track in the random selections, press [REPEAT] repeatedly until ??? TRACK??? appears during playback.

???To repeat the entire random selections, press [REPEAT] repeatedly until ??? ALL??? appears during playback.

???During Random Playback, you cannot go back to the previous track.

PLAY

Hint

???Press [CLEAR/C.RESET] at step 2) to erase the most recently entered track.

???To erase all programmed tracks at once, select ???ALL CLEAR?????? and press [ENTER] at step 2).

???While a program is being played back, [STOP C] works as follows;

??Press [STOP C] and [PLAY B] next, so that the programmed playback restarts.

??Press [STOP C] twice and [PLAY B] next, so that playback restarts from the first track in the original order. However, your programmed playback can be restarted when you follow above steps. (Your programs are still stored until either the disc tray is open or power is turned off.)

???To repeat the current track in the program, press [REPEAT] repeatedly until

??? TRACK?????? appears during playback.

???To repeat the entire program, press [REPEAT] repeatedly until ??? ALL?????? appears during playback.

Special Settings

Subtitle Language

DVD

DVD-V

This unit allows you to select a subtitle language (if available) during DVD play- back.

Each time you press [SUBTITLE/T-SET],

subtitle language changes as example below.

OFF (no subtitles)

ENG (English subtitles)

FRE (French subtitles)

ENG (English audio)

SPA (Spanish audio)

FRE (French audio)

...

To set subtitle ON/OFF

Hint

??? If your language is not shown after press- ing [AUDIO] or [SUBTITLE/T-SET] several times, the disc may not have that lan- guage. However, some discs allow audio language or subtitle language setting on the disc menu. (Operation varies depend- ing on the discs, so refer to the manual

Hint

???Some discs will only allow you to change the audio setting from the disc menu. Refer to the manual accompanying the discs for details.

???When ???OFF??? appears on the TV screen, it means audio language is not available.

???If your language is not shown after pressing [AUDIO] several times, the disc may not have that language. However, some discs allow audio language setting on the disc menu. (Operation varies depending on the disc, so refer to the manual along with the disc.)

Camera Angle

DVD

DVD-V

Some DVD discs may con- tain scenes which have

been shot simultaneously

from various angles. You can change the camera angle if the icon appears on the screen. If the ???ANGLE ICON??? setting is ???OFF??? in the OTHERS menu, the icon will not appear. (Refer to pages 20 and 22.)

Each time you press [AUDIO], sound mode changes as example below.

STEREO (right and left channels are active)

L-ch (left channel is active)

Virtual Surround

DVD

DVD-V CD

You can enjoy stereophonic virtual world on your existing 2 channel stereo system.

MODE

Press twice (once for CD ).

DVD Functions

along with the disc.)

??? When ???NOT AVAILABLE??? appears on the TV screen, it means no subtitle is recorded on the scene.

??? If you choose a language that has three- letter-language code, the code will be dis- played every time you change the subtitle language setting. If you choose any other languages, ???---??? will be displayed instead.

(Refer to page 24.)

??? Some discs will only allow you to change the subtitle from the disc menu. Refer to the manual accompanying the discs for details.

Black Level Setting

DVD

DVD-V

Adjust the Black Level Setting to make the dark areas of the TV picture brighter.

3RETURN

Hint

For CD play back only

???Virtual Surround will not be effective if the sound mode is set to something other than STEREO. Refer to ???Stereo Sound mode???.

???When playing back 96kHz with Virtual Surround function, the sound will be down sampling at 48kHz and output as digital audio.

BDISPLAY Setting

You can change the display functions. Follow steps 1) to 3) in the ???CUSTOM Menu??? section on page 20.

ENTER

Select the desired setting.

ENTER

Select the desired setting.

ENTER

6 To exit the menu

SETUP

Hint

TV ASPECT:

???Select ???4:3 LETTER BOX???, so that black bars may appear on the top and bottom of the screen.

???Select ???4:3 PAN & SCAN??? for a full height picture with both sides adjusted.

???Select ???16:9 WIDE??? if a wide- screen TV is connected to this unit.

STILL MODE:

PROGRESSIVE:

???You can set ???PROGRESSIVE??? to ???OFF??? either in the DISPLAY menu or by pressing and hold- ing [PLAY B] on the front of the unit for more than 5 seconds.

???When ???PROGRESSIVE??? is ???ON???, video signals from VIDEO OUT and S-VIDEO OUT jacks will be distorted or not be output at all.

Functions

Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow steps 1) to 3) in the ???CUSTOM Menu??? section on page 20.

DOLBY DIGITAL: QUICK

(Default: BITSTREAM)

Set to ???BITSTREAM??? when the unit is connected to a Dolby Digital decoder.

???BITSTREAM: Outputs a Dolby Digital Signals.

???PCM: Convert the Dolby Digital into PCM (2 channel).

ENTER

6To exit the menu

SETUP

Hint

DRC:

???This function is available only on the discs which are recorded in the Dolby Digital format.

DOWN SAMPLING:

???When playing disc with copyright Protection, the sound will be down sam- pled at 48kHz, even if you set to ???OFF???.

???This function is avail- able only on digital out- putting of a disc recorded in 96kHz.

DVD

DPARENTAL Setting

Parental Control limits the disc viewing that exceed your settings. (An incorrect password will not be accepted.) This feature prevents your children from viewing inappropriate materials.

Parental Levels

Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set. Follow steps 1) to 3) in the ???CUSTOM Menu??? section on page 20.

Hint

???DVD-Video discs may not respond to the parental lock settings. Make sure this function works with your DVD-Video discs.

To Change the Password for Parental Controls

You can change your password for parental controls. Follow steps 1) to 3) in the ???CUSTOM Menu??? section on page 20.

7To exit the menu

SETUP

ENTER

Hint

???Record the password in case you forget it.

???If you forget the pass- word, press [4], [7], [3], [7] at step 4), then enter your new password. Password will be cleared and parental levels will be set to ???ALL???.

You can change the other functions. Follow steps 1) to 3) in the ???CUSTOM Menu??? section on page 20.

1Conexiones

Consulte la ???Basic TV Connection??? en la p??gina delantera antes de utilizar esta unidad.

Canal de salida RF

Si el canal 3 se est?? utilizando para una transmisi??n.

1)Programe su televisor al canal 4. 2)Inserte una cinta pregrabada en esta

unidad.

3)Pulse [OUTPUT] en la unidad para que se encienda la luz VCR OUT- PUT.

???Si aparece ruido en la pantalla de TV, presione [VCR/TV] en el mando a distancia.

4)Pulse una vez [PLAY B]. 5)Despu??s de unos segundos, pulse

[PLAY B] en la unidad durante 3 segundos.

???El canal de salida RF cambiar?? del canal 3 al canal 4 y podr?? ver una imagen reproducida.

???Cuando no aparezca una imagen en la pantalla del televisor, repita el paso 4).

6)Pulse [STOP C] para parar la repro- ducci??n.

2Instalaci??n de las pilas del control remoto

???

3Conmutaci??n VCR/DVD

Bot??n OUTPUT

MODO VCR

Pulse [VCR] en el control remoto. (Compruebe que est?? encendida la luz

VCR OUTPUT.)

MODO DVD

Pulse [DVD] en el control remoto. (Compruebe que est?? encendida la luz

Espa??ol

4Activaci??n de la unidad por primera vez

VCR

Encienda el televisor y sin- tonice al canal 3.

???Si el canal 3 se est?? utilizando para una trans- misi??n, vea la secci??n ???Canal de salida RF???.

Conecta el cable de la caja de canales de cable o la caja de sat??lite en la toma ANT-IN de la unidad?

Si Pulse [MENU]

para salir.

No Espere unos minutos.

Despu??s del escaneo...

???El sintonizador se detiene en el canal memorizado m??s bajo.

???Puede seleccionar s??lo los canales memo- rizados en esta unidad con

[SKIP/CH. G/K H/L] (o [CHANNEL K/L]).

???Si aparece nuevamente ???AJUSTE AUTO??? en la pantalla de TV, verifique las conex- iones de cable. Presione nuevamente [B].

5Ajuste del reloj

VCR

PROGRAMAR

AUTOREPETIR [OFF]

AJUSTE CANAL

BAJUSTE DE RELOJ

SELEC. IDIOMA

SALIDA DEL AUDIO

TV ESTEREO [ON]

SAP

??? Si no se ha ajustado el reloj,

Seleccione "AM" o "PM".

DVD OUTPUT.)

Consejo

???Si pulsa s??lo [OUTPUT] en el panel frontal NO camb??a el modo del control remoto. DEBE seleccionar tambi??n el modo correcto en el control remoto.

aparece la pantalla AJUSTE DE RELOJ cuando pulse [MENU]. En este caso, vaya al paso 2).

Espa??ol

???

1Connections

Please refer to ???Basic TV Connection??? on the front page before you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.

???If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, hold [PLAY B] on the unit for 3 seconds.

???The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

???When a picture does not appear on the TV screen, repeat step 4).

6)Press [STOP C] to stop playback.

2Installing the Batteries for the Remote Control

3VCR/DVD Switching

OUTPUT button

Quick Use Guide

4Turn on the unit for the first time

VCR

Turn on the TV and set it to channel 3.

???If channel 3 is already occupied for broadcasting, see???RF Output Channel??? section.

Do you connect the cable from the cable box or the satellite box to the unit???s ANT-IN jack?

YES

Yes Press [MENU]

to exit.

No Please wait for a few minutes.

After scanning...

???The tuner stops on the lowest memorized channel.

???You can select only the channels memo- rized in this unit by using

[SKIP/CH. G/K H/L] (or [CHANNEL K/L]).

???If ???AUTO SET UP??? appears on the TV screen again, check the cable connections. Then, press [B] once again.

VCR MODE

Press [VCR] on the remote control.

(Verify that the VCR OUTPUT light is lit.)

5Clock Setup

VCR

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD OUTPUT light is lit.)

Hint

???Pressing only [OUTPUT] on the front panel DOES NOT switch the mode of the remote control. You MUST select the cor- rect mode on the remote control.

1MENU

- M E N U -

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

BCLOCK SET

LANGUAGE SELECT

AUDIO OUT

TV STEREO [ON]

SAP

???If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2).

Select ???AM??? or ???PM???.

8To exit the CLOCK SET screen