???at panel solutions

LCD TV Wall Mount

Installation Manual

MAF121BKR

Tools Required

Phillips Head Screw Driver

Ratchet or Driver with 1/2??? (13 mm) Socket Electric Drill

1/4??? ( 6 mm) Drill Bit and Stud Finder for Dr y wall Installation 7/16??? (11 mm) Masonr y Bit for Concrete Installation

Warnings

1. Make sure these instructions are read and thoroughly understood before attempting installation. If you are unsure of any par t of this installation, contact a professional installer for assistance.

2.

3.

4.

5. Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display. Consult the owner???s manual for your display for more information.

CAUTION:

This wall mount is intended for use only with the ma ximum weight of

36 kg /80 lbs. Use with heavier than the ma ximum weights indicated may result in instability causing possible injur y. Follow the installation and operation instructions carefully.

Hardware Kit

( R ) M6 Lag Bolt

Washer (x4)

Keep your sales receipt to obtain warranty par ts and ser vice and for proof of purchase. Attach it here and record the model number.

Model No. _____________________________________________________________

Purchase Date: _________________________________________________________

Dealer/Address /Phone __________________________________________________

Part 1a - Mounting the Wall Plate (Drywall)

Important ! For safety reasons, this mount must be secured to a wood stud and the stud must be capable of suppor ting the combined weight of the mount and display.

1. Using a high quality stud ???nder, locate and mark one stud for securing the mount.

2. With the help of another person, place the mount against the wall over the marked stud. Make sure the mount is level.

3. While another person holds the mount in place, mark two locations on the wall where the mount is to be installed.Fig.1

Be sure to use the center of the stud.

4. Set the mount aside and drill a 1/4??? ( 6 mm) pilot hole at each

marked location.

5. Place the mount back against the wall and secure it using the Lag Bolts ( Q ) and Lag Bolt Washers

( R ) provided (see Fig. 1). Do not over-tighten these bolts and do not release the mount until all bolts are in place

Part 1b ??? Mounting to the Wall (Concrete)

Important ! For safety reasons, the concrete wall must be capable of suppor ting the combined weight of the mount and display.

1.

2.

3.

4. Inser t a Concrete Anchor ( P) into each hole so that it is ???ush with the concrete sur face. A hammer can be used to lightly tap the anchors into place if necessar y.

NOTE : If the concrete wall is covered by a layer of plaster or dr y wall, the concrete anchor must pass completely through the layer to rest ???ush with the concrete sur face.

5. Place the mount back against the wall and secure it using the Lag Bolts ( Q ) and Lag Bolt Washers ( R ) provided (see Fig. 1). Do not over-tighten these bolts and do not release the mount until all bolts are in place.

Part 2 - Attaching the Arms to the Display

Important ! Use extra care during the par t of the installation. If possible, avoid placing your display facedown as it may damage the viewing sur face.

Note: Your mount comes with a selection of bolt diameters and lengths to accommodate a wide variety of display models. Not all of the hardware

in the kit will be used.

1.Determine the correct length of bolt to use with your display by ???rst examining the back of your display.

A. If your display has a ???at back, you will use one of the shor ter bolts (A, D, G, or J ) from the hardware kit.

B. If your display has a cur ved or recessed back, you will use one of the longer bolts ( B, E, H, or K ) along with a spacer ( M or N ).

2. Determine the correct diameter of bolt to use by

carefully tr ying one bolt each from Bags 1 - 4 ofFig. 2 the hardware kit. Do not force any of the bolts ???

if you feel resistance stop immediately and tr y a smaller diameter bolt.

3.Attach the arms to the back of your display using the bolts identi???ed in Steps 1 and 2 along with the corresponding Lock Washer ( C, F, I, or L) (see Fig. 2 and 3 ).

A. If you are using the M4, M5, or M6 bolts ( Bags 1, 2, and 3 respectively), you will also need to use the M6 Washers ( O ).

B. If you are using one of the longer bolts on a display with a cur ved or recessed back, you

will also use a Spacer ( M or N ). Use the Smaller Spacer ( M ) for M4 and M5 bolts and the Large Spacer ( N ) for M6 and M8 bolts.

4.Make sure all screws are secure, but do not over-tighten them.

Fig. 3

For displays with ???at backs... For displays with cur ved or recessed backs

Part 3 - Final Installation and Adjustment

1. With the help of another

person, carefully lif t your

display and place it on mountFig. 4 (see Fig. 4). Place the display

in the middle of the mount, and do not release the display until the mounting arms have securely hooked onto the crossbars.

3.Use the cable management hooks to help keep your power cord and other cables in order.

5. If any of the arms become too lose to hold their position, they can be tightened using the Alley Key provided in your hardware kit (see Fig. 6 ).

6. To adjust the tilt position of your display, have one person hold the display in place while another person loosens the two tilt adjustment knobs located on either side of the mount (see Fig. 7). Once the knobs are loose, move the display to the desired angle. Tighten the knobs securely before releasing the display. NOTE: The tilt adjustment knobs have a ratchet feature. If you need

to change the position of the knob without tightening or loosening the screw, simply pull the knob out before moving it.

Limited Lifetime Warranty

Audiovox Electronics Corporation (the ???Company??? ) warrants to you the original retail purchaser of this product that should it, under normal use and conditions, be proven defective in material or workmanship during its lifetime while you own it, such defect(s) will be repaired or replaced (at the Company???s option) without charge for par ts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), speci???cation of defect(s), transpor tation prepaid, to the Company at the address shown below. Do not return this product to the Retailer.

This Warranty does not cover product purchased, ser viced or used outside the United States or Canada.

This Warranty is not transferable and does not extend to costs incurred for installation, removal or reinstallation of the product. This Warranty does not apply if in the Company???s opinion, the product has been damaged through alteration, improper installation, mishandling, misuse, neglect, or accident. THE EX TENT

OF THE COMPANY???S LIABILIT Y UNDER THIS WARRANT Y IS LIMITED TO THE

REPAIR OR REPL ACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE

COMPANY???S LIABILIT Y EXCEED THE PURCHASE PRICE PAID BY PURCHASER

FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED

WARRANTIES, INCLUDING ANY IMPLIED WARRANT Y OF MERCHANTABILIT Y

OR FITNESS FOR A PARTICUL AR PURPOSE SHALL BE LIMITED TO DURATION

OF THIS WARRANT Y. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states / provinces do not allow limitations on how long an implied warranty lasts or

the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you speci???c legal rights and you may also have other rights which var y from state /province to state /province.

U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788

CANADA: Audiovox Return Center, c /o Genco, 6685 Kennedy Road, Unit 3, Door 16, Mississauga, Ontario L5T 3A5

Trademark(s) Registered

All other brands and product names are trademarks or registered trademarks of their respective owners.