Lyra Wireless

User???s Guide

Changing Entertainment. Again.

RD900W

Important Information

Refer to the identification/rating label located on the back panel of your product for its proper operating voltage.

FCC Regulations state that unauthorized changes or modifications to this equipment may void the user???s authority to operate it.

Product Registration

Please fill out the product registration card (packed separately) and return it immediately or register on-line at rca.com. Registering allows us to contact you if needed.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. The numbers are located on the bottom or back of the product.

Model No. _______________________________________________________________________

Serial No. ________________________________________________________________________

Purchase Date: ___________________________________________________________________

Dealer/Address/Phone: _____________________________________________________________

1

2

Chapter 1: Connections and Setup

Things to Consider Before You Connect

Protect Against Power Surges

???Connect all components before you plug any of their power cords into the wall outlet.

???Turn off all components before you connect or disconnect any cables.

Protect Components from Overheating

???Don???t block ventilation holes on any of the components. Arrange the components so that air can circulate freely.

???Don???t stack components.

???When you place components in a stand, make sure you allow adequate ventilation.

???If you connect an audio receiver or amplifier, place it on the top shelf so the heated air from it won???t flow around other components.

Position Cables Properly to Avoid Audio Interference

??? Insert each cable firmly into the designated jack.

Chapter 1: Connections and Setup

Audio System Requirements

??? Audio receiver with auxiliary inputs (line level) or other component with audio inputs (TV, VCR, etc.).

Computer System Requirements

Windows?? PC Requirements

???Pentium 300MHz or higher

???Windows?? 98SE, Me, 2000, or XP

???Microsoft Internet Explorer 5.0 or higher

???Internet access

???50MB free hard disk space

???400MB for MUSICMATCH Jukebox Radio MX??? feature (recommended)

???96MB RAM (32MB for Win98)

???CD-ROM drive capable of digital audio extraction

???Available USB port

???16-bit color video card

For more information, Frequently Asked Questions (FAQs), and the latest software updates for your Lyra Wireless, visit www.rca.com/digitalaudiodownloads

Windows is a trademark of Microsoft Corporation, registered in the U.S.A. and other countries.

MUSICMATCH, MUSICMATCH Jukebox, and MUSICMATCH Radio MX are registered trademarks of MUSICMATCH Corporation.

Chapter 1: Connections and Setup

Unpack the box and check your parts

All of the items shown below should have come packed in the box with your Lyra Wireless.

Chapter 1: Connections and Setup

Remote control antenna

Chapter 1: Connections and Setup

3 4

CHANNEL

9V

POWER

2

5 1

Connecting the Lyra Wireless Transmitter to your Computer

1.Connect the small end of the USB cable to the USB jack on the back of the Lyra Wireless transmitter and the other end to the USB jack on your computer.

2.Connect the small end of the large power supply to the power jack on the back of the Lyra Wireless transmitter and the other end into an AC outlet.

3.Make sure the ON switch is set to ON (the power indicator comes on).

4.Make sure the CHANNEL switch is set to the same channel as the CHANNEL switch on the Lyra Wireless receiver.

5.Extend and position the wire antenna on the back of the unit for best possible remote control reception.

6.Raise the antenna on the front of the unit so it is straight up.

7.Position the transmitter so that it is facing in the general direction of the receiver.

8.Follow the steps on the next page to connect the Lyra Wireless receiver to your audio receiver.

Chapter 1: Connections and Setup

Connecting the Lyra Wireless Receiver to your Audio Receiver

1.Connect the small end of the audio cable to the LINE OUT jack on the back of the Lyra Wireless receiver and the other ends (the red and white plugs) to the Audio Input jacks (sometimes labeled Aux or Line ) on your audio receiver. Also, make sure to put your audio receiver in the right mode to receive the sound from those jacks (see your audio receiver???s owner???s manual for more information).

2.Connect the small end of the small power supply to the power jack on the back of the Lyra Wireless receiver and the other end into an AC outlet.

3.Make sure the CHANNEL switch is set to the same channel as the CHANNEL switch on the Lyra Wireless transmitter.

4.Raise the antenna on the front of the unit so it is straight up.

5.Position the receiver so that it is facing in the general direction of the transmitter.

Chapter 1: Connections and Setup

Improving Performance

Orientation of the Antennas

Proper orientation of the antennas is important for good performance. You may find that the system works better with one or more of the antennas in the horizontal (flat) position. The receiver and transmitter tend to operate better in high locations, where the signal path is wider and stronger (on a shelf, for example). Watch the receiver signal strength indicators for indication of signal strength.

You may also need to experiment with the position of the remote control antenna on the transmitter unit. See what position works the best for the remote control.

The Lyra Wireless transmitter and receiver antennas can rotate to multiple positions. You may want to try several different angles for the best reception.

Chapter 1: Connections and Setup

Fine Tuning the Lyra Wireless

To get the best signal reception, the Lyra Wireless units should face each other using an imaginary ???line of sight.??? You can place the transmitter and receiver in separate rooms, or even separate floors of your house, so you don???t have to worry about the units being close to each other. Other barriers in your house may affect the signal, so you may need to adjust the positions of the transmitter and receiver somewhat.

If the transmitter is sending the signal to the receiver properly, you should see some of the receiver???s signal strength meter indicators light up.

If there is no signal at all

Make sure the CHANNEL switch on the back of both units is set to the same number.

If the signal is weak or there is interference

Try changing the channel on both units. Make sure the CHANNEL switch is set to the same channel on both units.

Lyra Wireless Receiver

Table or high shelf

Lyra Wireless

Transmitter

Table or high shelf

The Lyra Wireless system can transmit through walls and floors (up to 100 ft.).

Avoiding Interference

Cordless Phone and Baby Monitor Interference

The transmitter and receiver have 4 RF channels, but if you have a 900Mhz cordless phone or baby monitor, pick a channel that doesn???t interfere with the phone or monitor. Channel 4 is typically the channel with the least interference with telephones and baby monitors. If you have interference, leave your cordless phone or monitor on, then switch to a channel on both Lyra Wireless units that is clear.

Chapter 2: MUSICMATCH and the Lyra Wireless

Install the software on your computer

In order to play music through the Lyra Wireless system, you need to install some software first. The Music Management CD that came with your Lyra Wireless contains all the software you need.

The MUSICMATCH Jukebox??? software organizes your music collection and plays it through the Lyra Wireless system, and the remote control application makes it easier to navigate through MUSICMATCH.

MUSICMATCH compresses audio files (from music CDs) to the mp3 format so you can play them through the Lyra Wireless system. It also enables you to play music from internet radio.

1.Turn on your computer and place the Music Management CD that came with your Lyra Wireless into your computer.

2.If the setup screen does not appear, double click My Computer, double click your CD-ROM drive icon, and double click install.exe. You can also click, Run, then type D:\install.exe (where D is the letter of your CD-ROM drive). (The Lyra Wireless Quick Start screen appears.)

3.Click Install Remote Control Application to install the Lyra Wireless remote control application.

4.When the RCA Lyra Wireless Setup screen appears, click Next to begin setup.

5.Read the License Agreement and click Yes to continue the installation.

6.Click Next to select the destination location of the

Chapter 2: MUSICMATCH and the Lyra Wireless

Chapter 2: MUSICMATCH and the Lyra Wireless

Chapter 2: MUSICMATCH and the Lyra Wireless

Chapter 2: MUSICMATCH and the Lyra Wireless

Audio Setup

Depending on how your computer is currently set up, you may have to make some adjustments so that the music and sound are directed to the right places. You may need to make sure MUSICMATCH is configured properly, too (see below).

Settings in MUSICMATCH

1.Make sure the MUSICMATCH application is launched on your computer. If it???s not, press the LYRA WIRELESS button on the remote.

2.From MUSICMATCH???s main menu, click on Options and then Settings.

3.Select the Player tab, then click on the arrow under

Output Control and select USB Audio Device (or Lyra Wireless for Windows XP).

Note: For Windows 98SE, 2000, and Me, the Lyra Wireless is recognized as a ???USB Audio Device.??? If there is more than one USB audio device, the system numbers all the devices.

The MUSICMATCH Settings screen for

Windows 98SE, 2000, and Me.

The MUSICMATCH Settings screen for

Windows XP.

Chapter 2: MUSICMATCH and the Lyra Wireless

Soundcard Settings in Your Computer???s Control Panel

Note: This setting configures the chime and Windows sounds that play through your computer???s sound card. If you want them to play through the Lyra Wireless, select USB Audio Device (or Lyra Wireless, for Windows XP) under the preferred device setting.

If you have Windows 98SE or Me

1.Click on the Start icon in the lower left-hand corner of your screen.

2.Select Settings, followed by Control Panel (the Control Panel window appears).

3.Double click on the Multimedia icon, and select the

Audio tab.

4.Click on the arrow under Preferred device and make sure your sound card is selected.

The sound card settings screen for

Windows 98SE and Me.

If you have Windows 2000

1.Click on the Start icon in the lower left-hand corner of your screen.

2.Select Settings, followed by Control Panel (the Control Panel window appears).

3.Double click on the Sounds and Multimedia icon, and select the Audio tab.

4.Click on the arrow under Preferred device and make sure your sound card is selected.

The sound card settings screen for

Windows 2000.

Chapter 2: MUSICMATCH and the Lyra Wireless

If you have Windows XP

1.Click on the Start icon in the lower left-hand corner of your screen.

2.Select Settings, followed by Control Panel (the Control Panel window appears).

3.Double click on the Sounds and Audio Devices icon, and select the Audio tab.

4.Click on the arrow under Default device and make sure your sound card is selected.

The sound card settings screen for

Windows XP.

CD-ROM Settings in Your Computer???s Control Panel

If you have Windows 98SE

1.Click on the Start icon in the lower left-hand corner of your screen.

2.Select Settings, followed by Control Panel (the Control Panel window appears).

3.Double click on the Multimedia icon, and select the CD Music tab.

4.Under CD-ROM Selection, click the box for Enable digital CD audio for this CD-ROM device.

1.Click on the Start icon in the lower left-hand corner of your screen.

2.Select Settings, followed by Control Panel (the Control Panel window appears).

3.Double click on the System icon, and select the Device Manager tab.

(continued on next page)

Chapter 2: MUSICMATCH and the Lyra Wireless

4.Double click on the CD-ROM in the device list.

5.Click on the CD-ROM drive you want to use with MusicMatch Juke Box.

6.Click the Properties button, then click on the Properties tab.

7.Click the box for Enable digital CD audio for this CD-ROM device.

Note: Some CD-ROM devices do not support digital CD audio, and are not compatible with the Lyra Wireless. If

Enable digital CD audio for the CD-ROM device is grayed out, your CD-ROM is not compatible.

Chapter 2: MUSICMATCH and the Lyra Wireless

More on MUSICMATCH

To let you get started listening to your music, we???ll only mention the MUSICMATCH features that directly apply to the Lyra Wireless in this user???s guide. For additional information about MUSICMATCH Jukebox features such as MUSICMATCH Radio MX, creating music CDs, and all the music library features, go to:

???The MUSICMATCH tutorial on the Lyra Wireless Quick Start screen.

???Getting Started tips

???Online help (www.musicmatch.com)

Note: MUSICMATCH Radio MX requires a subscription. See the MUSICMATCH website for details.

Install Batteries in the Remote

1.Remove the battery compartment cover on the back of the remote.

2.Insert new batteries. Match the polarities (+ and ???) on the batteries with the diagram on the remote.

3.Put the battery compartment cover back on the remote.

Important Battery Information

???If you???re not going to use the remote for a month or more, be sure to remove the batteries because they can leak and cause damage.

???Dispose of batteries in the proper manner, according to federal, state, and local regulations.

???Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all batteries are not replaced at the same time, if disposed of in fire, or if an attempt is made to charge a battery not intended to be recharged.

???Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.

Using the Remote with the Lyra Wireless and Other Components

The software that comes with your Lyra Wireless enables you to use the remote to control many of the MUSICMATCH features. When you want the remote to operate MUSICMATCH, point it at the Lyra Wireless transmitter and press a button.

The remote control antenna of the Lyra Wireless system allows you to operate MUSICMATCH from another room, or even another floor of your house, so you don???t have to worry about being right in front of the transmitter. For more information on how to use the remote with MUSICMATCH, go to the end of this chapter.

For other components (TV, VCR, etc.), the remote has to be pointed in the correct direction and toward the correct component in order for the remote control???s signal to communicate with the sensor on the component. Make sure there is a clear path between the remote control and the component you want to operate, so the signal isn???t blocked.

Chapter 2: MUSICMATCH and the Lyra Wireless

Playing Music through the Lyra Wireless

Now that you have connected your Lyra Wireless and installed all the necessary software, it???s time to listen to some music.

1.Make sure the MUSICMATCH application is launched on your computer. If it???s not, press the LYRA WIRELESS button on the remote.

2.Select the music source you want to play by pressing the corresponding button on the remote (FILE, RADIO, CD). If you choose FILE or CD, also select the song you want to play.

3.Turn on your audio receiver or other audio component and make sure it is on the right input mode for how you connected the Lyra Wireless receiver unit (AUX, INPUT, etc.). See you owner???s manual for the audio system or audio component for more details.

4.Adjust the volume on your computer and audio receiver to a comfortable level.

5.Press PLAY (the song plays through your audio receiver).

Fine Tuning the Lyra Wireless

To get the best signal reception, the Lyra Wireless units should face each other using an imaginary ???line of sight.??? You can place the transmitter and receiver in separate rooms, or even separate floors of your house, so you don???t have to worry about the units being close to each other. Other barriers in your house may affect the signal, so you may need to adjust the positions of the transmitter and receiver somewhat (see the diagrams in Chapter 1).

If the transmitter is sending the signal to the receiver properly, you should see some of the receiver???s signal strength meter indicators light up.

If there is no signal at all

Make sure the CHANNEL switch on the back of both units is set to the same number.

If the signal is weak or there is interference

Try changing the channel on both units. Make sure the CHANNEL switch is set to the same channel on both units.

Improving Performance

Orientation of the Antennas

Proper orientation of the antennas is important for good performance (see the diagrams in Chapter 1). You may find that the system works better with one or more of the antennas in the horizontal (flat) position. The receiver and transmitter tend to operate better in high locations, where the signal path is wider and stronger (on a shelf, for example). Watch the receiver signal strength indicators for indication of signal strength.

Also, you may need to experiment with the position of the remote control antenna on the transmitter unit. See what position works the best for the remote control.

Chapter 2: MUSICMATCH and the Lyra Wireless

Using the Remote with MUSICMATCH

You can use the remote to control several of the functions of MUSICMATCH, including launching the MUSICMATCH software; changing play modes (radio, music files, CDs); adjusting the volume; and changing tracks, playlists, and internet radio stations.

Music source buttons

Chapter 3: Additional Information

Troubleshooting

Most problems you encounter with your Lyra Wireless can be corrected by consulting the following troubleshooting list.

Note: For additional troubleshooting information, visit www.rca.com/digitalaudiodownloads or call 580-634-0115.

General Problems

Lyra Wireless won???t turn on

???Make sure both the transmitter and receiver are plugged in.

???Check the wall receptacle (or extension cord) to make sure it is ???live??? by plugging in something else.

No sound

???Make sure all the connections are snug between the Lyra Wireless receiver and your audio receiver (or other component).

???Make sure the music is not being sent to your sound card. In the MUSICMATCH menu, select Options, then Player, then Settings. Under Output Control, make sure USB Audio Device is selected (or Lyra Wireless for Windows XP). If it wasn???t already selected, you may have to restart MUSICMATCH to activate the new setting. Once you restart, try playing the music again. You should hear audio play through your audio system (not from your PC). The normal Windows sound prompts should still play through your PC.

???Make sure the correct input mode or channel is selected on your audio system. In order for your audio system to receive the sound coming from the Lyra Wireless, the correct input mode must be selected (AUX, INPUT, etc.). See your owner???s manual for the audio system or component for more details.

The chime sound and Windows prompts are playing through the Lyra Wireless

???Make sure your sound playback settings are correct. If all sounds are playing through your audio system, including Windows sound prompts, you need to set the Windows prompts to only play through your sound card. See page 16 for details.

Poor reception

???Make sure the antenna is positioned correctly. Proper orientation of the antenna is important for good performance. You may find that the system works better with one or more of the antennas in the horizontal (flat) position. The receiver and transmitter tend to operate better in high locations, where the signal path is wider and stronger (on a shelf, for example). Watch the receiver signal strength indicators for indication of signal strength.

???Your cordless phone or baby monitor may be causing interference. The transmitter and receiver have 4 RF channels, but if you have a 900Mhz cordless phone or baby monitor, pick a channel that doesn???t interfere with the phone or monitor. Channel 4 is typically the channel with the least interference with telephones and baby monitors. If you have interference, leave your cordless phone or monitor on, then switch to a channel on both Lyra Wireless units that is clear.

Chapter 3: Additional Information

The Remote Control Doesn???t Work

???Something might be between the remote and the remote sensor on the component. Make sure there is a clear path. (This is only when using the remote to operate other components, such as a TV or VCR.)

???Maybe batteries in remote are weak, dead, or installed incorrectly. Put new batteries in the remote.

???You may need to reset the remote control: remove batteries and press the number 1 button for at least 60 seconds. Release the 1 button, replace the batteries, and reprogram, if necessary.

Care and Cleaning

CAUTION: Turn OFF your unit before cleaning.

You can clean the unit as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the cabinet to help assure adequate ventilation.

Never use strong cleaning agents, such as ammonia-based cleaners, or abrasive powder. These types of cleaners will damage the unit.

Avoid placing drinks or vases with water on top of the unit. This could increase the risk of fire or shock hazard or damage to the unit.

Chapter 3: Additional Information

Chapter 3: Additional Information

SHUF???REPEAT Puts a compatible CD player or DVD player in repeat or shuffle mode.

STOP Stops the current function (record, playback, rewind, etc).

TAPE Puts a compatible audio receiver in tape mode.

TV Turns on a compatible RCA, GE, or Proscan TV and puts the remote in TV mode. Also used with the ON???OFF button to turn on/off a compatible TV.

VCR Turns on a compatible VCR and puts the remote control in VCR mode.

VOL < and > Raises and lowers the volume of some compatible TVs.

WHO??? INPUT In VCR or TV mode, selects between the Video Input Channels and the tuner. Video Input Channel refers to the signal coming from the component connected to audio/video input jacks on the VCR or TV.

Chapter 3: Additional Information

Chapter 3: Additional Information

How to Use the Remote After You???ve Programmed It

Because this universal remote can control several different components (TV, DVD, VCR, satellite receiver, etc.) it uses operational modes triggered by the component buttons. For example, if you want the remote to control the TV, you would press the TV button to put the remote into TV mode before you could control the TV.

1.Press the appropriate component button (DVD, TV, VCR, SAT???CABLE, AUX) to set the remote to control the component.

2.Press ON???OFF to turn the component ON or OFF.

3.Use the remote buttons that apply to that component.

Notes:

???The remote may not be compatible with all brands and models of components. It also may not operate all functions of the remote that came with your component.

???If you keep pressing buttons and nothing happens, the remote is probably in the wrong mode. You must press the component button that matches the component you want to operate (i.e., if you want to operate the VCR, press VCR on the remote control to put the remote in VCR mode.)

Chapter 3: Additional Information

Chapter 3: Additional Information

Chapter 3: Additional Information

Chapter 3: Additional Information

Chapter 3: Additional Information

FCC and Industry Canada Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.

???Consult your service provider or an experienced radio/TV technician for help.

FCC regulations state that unauthorized changes or modifications to this equipment may void the user???s authority to operate it.

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Important: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Chapter 3: Additional Information

Limited Warranty

What your warranty covers:

??? Defects in materials or workmanship.

For how long after your purchase:

???90 days from date of purchase - Unit repair or exchange, which includes parts and labor.

???91 days to 1 year from date of purchase - Unit repair or exchange, which includes parts only; you pay the labor.

???The warranty for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.

What we will do:

???During the initial 90 days:

Repair or exchange the defective portion of your Lyra Wireless. If the unit is replaced it will be with a new or, at our option, refurbished unit.

???After the 90 days and within one year:

Repair or exchange the defective portion of your Lyra Wireless. If the unit is replaced it will be with a new or, at our option, refurbished unit.

We will charge you a flat rate to repair or replace a defective Lyra Wireless. This charge covers the labor cost for its repair.

How you get service:

???Call 580-634-0115 and have your unit???s date of purchase and model/serial number ready. The model/serial number information is on your unit.

???A representative will troubleshoot your problem over the phone.

???If the representative determines that you should receive a replacement unit, you will be provided with a Service Request (SR) number and the location of a nearby exchange point, if one exists. No returns will be accepted without an SR number.

???Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required.

???Write the SR number on the outside of the carton used to return the unit. Make sure you insure your shipment in case of damage or loss.

???Carefully pack the unit using the original box and packing material if possible. Please retain all non-defective accessories that were included with your unit such as the headphones.

???Include with the shipment:

1.Evidence of purchase date such as a bill of sale.

2.A brief note describing your unit???s problem.

3.Your name, address and phone number.

???After we receive your product, it will be repaired, or a new, or at our option, refurbished unit will be shipped to you.

Chapter 3: Additional Information

What your warranty does not cover:

???Acts of nature, such as but not limited to lightning damage.

???Adjustment of customer controls.

???Damage from misuse or neglect.

???A unit that has been modified or incorporated into other products or is used for institutional or other commercial purposes.

???Batteries.

???Units purchased, serviced or operated outside the U.S.A.

???Loss of customer???s software, firmware, information, or memory data.

???Installation.

???Shipping damage if the unit was not packed and shipped in the manner prescribed by Thomson.

Product Registration:

???Please complete and mail the Product Registration Card packed with your product. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage.

Limitation of Warranty:

???THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO

VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES

SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.

???REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF

THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF

ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES

AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO

THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE

WARRANTY PERIOD SET FORTH ABOVE.

How State Law relates to warranty:

???Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.

???This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.

If you purchased your unit outside the United States:

??? This warranty does not apply. Contact your dealer for warranty information.