CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

CAUTION: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user???s authority to operate it.

CAUTION: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

???Unplug the display if you are not going to use it for an extensive period of time.

???Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off.

However, never use alcohol, solvents or ammonia-based liquids.

???Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.

???The casing cover should be opened only by qualified service personnel.

???Keep the display out of direct sunlight and away from stoves or any other heat sources.

???Remove any object that could fall into the vents or prevent proper cooling of the display???s electronics.

???Do not block the ventilation holes on the cabinet.

???Keep the display dry.To avoid electric shock, do not expose it to rain or excessive moisture.

???If turning off the display by detaching the power cable, wait for 6 seconds before re-attaching the power cable for normal operation.

???To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.

???When positioning the display, make sure the power plug and outlet are easily accessible.

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer???s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS TO

RAIN OR MOISTURE.

WARNING: Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

WARNING: The batteries (batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

WARNING: The mains plug or appliance coupler is used as the disconnect device,the disconnect device shall remain readily operable.

WARNING: To prevent the spread of fire, keep candles or other open flames away from this product at all times.

WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

CAUTION: These servicing instructions are for use by qualified service personnel only.To reduce the risk of electric shock,do not perform any servicing other than that contained in the operating instructions unless you are qualitified to do so.

CAUTION: Excessive sound pressure from earphones and headphones can cause hearing loss. Adjustment of the equalizer to maximum increases the earphone and headphone output voltage and the sound pressure level.

Therefore, to protect your hearing, adjust the equalizer to an appropriate level.

For UL/CUL application: For use only with UL Listed Wall Mount

Bracket with minimum weight/load: 41.1 kg.

For CB application: Unit without base weight: 13.7 kg.The equipment and its associated mounting means still remain secure during the test. (Used wall mounting kit: 400 x 400 mm distance by using M6 screws of 20 mm long plus the thickness of the mounting bracket.)

Regulatory Information

CE Declaration of Conformity

We declare under our responsibility that the product is in conformity with the following standards:

???EN60065:2002+A1:2006+A11:2008+A2:2010+A12:2011 (Safety requirement of Audio, video and similar electronic apparatus)

???EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment)

???EN55024:2010 (Immunity requirement of Information Technology Equipment)

???EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission)

???EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker)

???EN 50581:2012 (Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances)

following provisions of directives applicable:

???2006/95/EC (Low Voltage Directive)

???2004/108/EC (EMC Directive)

???2009/125/EC (ErP Directive, EC No. 1275/2008, 642/2009 Implementing Directive for Standby and Off mode power consumption)

???93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level.

???2011/65/EU (RoHS 2 Directive)

Federal Communications Commission (FCC)

Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate the equipment.

Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS

OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT

REGULATIONS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Polish Center for Testing and Certification

Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source.

The phasing conductor of the room???s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible.

A protection mark ???B??? confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251.

Information for U.K. only

WARNING ???THIS APPLIANCE MUST BE EARTHED.

This apparatus is supplied with an approved moulded 13A plug.To change a fuse in this type of plug proceed as follows:

1.Remove fuse cover and fuse.

2.Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3.Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.

NOTE: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.

How to connect a plug

Electric, Magnetic and Electronmagnetic

Fields (???EMF???)

1.We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.

2.One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.

3.We are committed to develop, produce and market products that cause no adverse health effects.

4.We confirm that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today.

5.We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization for early integration in its products.

The wires in the mains lead are coloured in accordance with the following code:

BLUE ??? ???NEUTRAL??? (???N???) BROWN ??? ???LIVE??? (???L???)

GREEN & YELLOW ??? ???EARTH??? (???E???)

1.The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with the letter ???E??? or by the Earth symbol or coloured GREEN or GREEN & YELLOW.

2.The BLUE wire must be connected to the terminal which is marked with the letter ???N??? or coloured BLACK.

3.The BROWN wire must be connected to the terminal which marked with the letter ???L??? or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead ??? not simply over the three wires.

China RoHS

????????????????????????????????????????????????

??????????????????????????????????????????????????????????????????

*??????????????????????????????????????????????????????????????????????????????????????? ??????????????????????????????

???????????????????????????????????????????????????????????????????????????SJ/ T11363-2006????????????????????????????????????????????????????????????????????? ?????????????????????

??????????????????????????????????????????????????????????????????????????????????? SJ/T11363-2006??????????????????????????????????????????????????????????????????

??????????????????

?????????????????????????????????????????????????????????????????????????????????????? ????????????????????????????????????????????????????????????

10

??????????????????

????????????????????????????????????????????????????????????????????? 10 ??????

???????????????????????????????????????????????????????????????????????????????????? ???????????????????????????????????????????????????????????????????????????????????? ???????????????????????????????????????????????????????????????????????????????????? ??????????????????????????????????????????????????????

?????????????????????????????????????????????????????????????????????

???????????????????????????????????????????????????

???????????????????????????????????????????????????????????????

???????????????????????????????????????????????????????????????????????????????????? ???????????????????????????????????????????????????????????????????????????????????? ????????????????????????????????????????????????????????????????????????????????? ??????

???2000m ?????????????????? 2000m ???????????????????????? :

??? ??? ?????????????????? 2000m ???????????????????????????

?????????

??? ???

??? ???

??? ??? Hai dou gaxgonq, wngdang sien duenh denvasen bae.

????????? ??? ??? ??????????????????????????????????????????

?????????????????????????????????????????????????????????

?????????

??? ???

??? ???

???Louzsim

Danghnaeuz denyouz vuenh ndaej mbouj habdangq aiq miz ??? ??? gij yungyiemj fatseng bauqcaq

Cijndaej yungh gij denyouz doengzyiengh loihhingz roxnaeuz daengjyauq loihl haenx vuenh???

?????????????????????????????????????????????????????????????????? , ??? ??? ??? ????????????????????????????????? !???

?????????

??? ???

??? ???

???Gij mizsienq vangjloz denhsen ciephaeuj bonj sezbi daeuj ??? ??? haenx itdingh aeu caeuq gij ciepdieg baujhoh doxliz, mboujne

aiq miz gij yungyiemj dawzfeiz daengj!???

North Europe (Nordic Countries)

Information

Placering/Ventilation

VARNING:

F??RS??KRA DIG OM ATT HUVUDBRYTARE OCH UTTAG

??R L??T??TKOMLIGA, N??R DU ST??LLER DIN UTRUSTNING

P??PLATS.

Placering/Ventilation

ADVARSEL:

S??RG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG

STIKKONTAKT ER NEMT TILG??NGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETT?? VERKKOJOHTO VOIDAAN

TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

N??R DETTE UTSTYRET PLASSERES, M?? DU PASSE P?? AT

KONTAKTENE FOR ST??MTILF??RSEL ER LETTE ?? N??.

End-of-Life Disposal

Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old display from your local Philips dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling contact www.eia.org (Consumer Education Initiative)

Waste Electrical and Electronie Equipment-

WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/ EC governing used electrical and electronic appliances, this product may not be disposed of with normal household waste.You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection.To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product.

End of Life Directives-Recycling

Your new Public Information Display contains several materials that can be recycled for new users.

Please dispose of according to all Local, State, and Federal laws.

As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Table Of Contents

7.2.Types of Pixel Defects +

1.Unpacking and Installation

1.1.Unpacking

???This product is packed in a carton, together with the standard accessories.

???Any other optional accessories will be packed separately.

???Due to the size and weight of this display it is recommended for two people to move it.

???After opening the carton, ensure that the contents are complete and in good condition.

1.2.Package Contents

Please verify that you received the following items with your package content:

??? LCD display

???CD ROM

???Remote control with AAA batteries

???Power cord (1.8 m)

???VGA cable (1.8 m)

??? RS232 cable (1.8 m)

??? Quick start guide

* The supplied power cord varies depending on destination.

CD ROM

LCD Display

BDL4620QL

Remote Control

and AAA Batteries

Kurzanleitung / Gu??a r??pida / Guide de d??marrage rapide / Guida rapida /

Instrukcja szybkiego uruchomienia / ?????????????? ?????????????????????? ???? ?????????????? /

H??zl?? ba??langi?? k??lavuzu / ?????????????????? / ??????????????????

Installation / Installation / Instalaci??n / Installation / Installazione / Instalacja /

?????????????????? / Kurulum / ?????? / ??????

Connect /Verbindungsf??higkeit / Conectividad / Connectivit?? / Connettivit?? /

Po????czenia / ?????????????????????? / Ba??lant?? / ????????? / ?????????

2.Parts and Functions

2.1.Control Panel

4

5

6

7

1 [] button

Press to switch the display on or off.

2 [] button

Press to select input source.

3 [] button

Press to access the OSD menu.

4 [ ] button

Press to move the highlight bar up to adjust the selected item while OSD menu is on.

5 [ ] button

Press to move the highlight bar down to adjust the selected item while OSD menu is on.

6 [] button

Press to increase the adjustment while OSD menu is on, or to increase the audio output level while OSD menu is off.

7 [ ] button

Press to decrease the adjustment while OSD menu is on, or to decrease the audio output level while OSD menu is off.

8

8Remote control sensor and power status indicator

???Receives command signals from the remote control. -- Lights green when this display is turned on

-- Lights red when this display is in standby mode

-- Lights off when the main power of this display is turned off

BDL4620QL

2.2.Input/Output Terminals

Y Pb Pr

1AC IN

AC power input.

2MAIN POWER SWITCH

Main power on/off switch.

3HDMI IN

HDMI video/audio input.

4DVI IN

DVI-D video input.

5RJ-45

LAN control function for the use of remote control signal from control center.

6VGA IN (D-Sub)

VGA video input.

7COMPONENT IN (RCA)

Component YPbPr video source input.

8AUDIO IN (RCA)

Audio input from external AV device.

9AUDIO OUT (RCA)

Audio signal output to connect your external AV device.

10AUDIO IN (3.5mm)

Audio input from your PC.

11SPDIF OUT

Digital audio signal output to connect your external AV device.

12IR OUT / 13 IR IN (3.5 mm)

IR signal output/input for the loop-through function.

NOTES:

???This display???s remote control sensor will stop working if the jack [IR IN] is connected.

???To remotely control your A/V device via this display, refer to page 8 for IR Pass Through connection.

14RS232C OUT / 15 RS232C IN (2.5 mm)

RS232C network output/input for the loop-through function.

16USB PORT

Connect your UBS storage device.

2.3.Remote Control

2.3.1. General functions

1 POWER button

Switch this display on or off.

2PLAY buttons

Control playback of media files.

3 SOURCE button

Select input source. Press [] or [] button to select from USB,

Network, HDMI, DVI, YPbPr, AV, or VGA. Press [] button to confirm and exit.

4 HOME button

Access the OSD menu.

5 LIST

No function.

6 NAVIGATION buttons

Navigate through menus and select items.

7 button

Confirm an entry or selection.

8 ADJUST button

Access currently available options, picture and sound menus.

9 BACK button

Return to the previous menu page or exit from the previous function.

10 VOLUME button

Adjust volume.

11 MUTE button

Press to turn the mute function on/off.

12 COLOR buttons

Select tasks or options.

13NUMERIC buttons

Enter text for network setting.

14 FORMAT button

Change picture format.

15 INFO button

Display information about current activity.

16 OPTIONS

Access currently available options, picture and sound menus.

DISPLAY

[IR OUT]

DVD / VCR / VCD

[IR IN]

[RJ-45]

PC

ROUTER

[RJ-45]

4.Operation

NOTE: The control button described in this section is mainly on the remote control unless specified otherwise.

4.1.Watch the ConnectedVideo Source

See page 7 for external equipments connection.

1.Press button.

2.Press or button to select a device, then press button.

4.2.Change Picture Format

You can change the picture format to suit the video source. Each video source has its available picture formats.

The available picture formats depend on the video source:

1.Press button.

2.Press or button to select a picture format, then press button.

???{Auto zoom}: Enlarge the picture to fill the screen.

Recommended for minimal screen distortion but not for HD or

PC.

???{Movie expand 16:9}: Scale 4:3 format to 16:9. Not recommended for HD or PC.

???{Wide screen}: Shows widescreen format content unstretched. Not recommended for HD or PC.

???{Unscaled}: Provide maximum detail for PC. Only available when PC mode is selected in the {Picture} menu.

???{4:3}: Display the classic 4:3 format.

4.3.Select your Preferred Picture Settings

1.While this display is playing video source, press button.

2.Press or button to select ???

, then press button.

3.Press or button to select an option, then press button:

???{Personal}: Apply your personalised picture settings.

???{Vivid}: Rich and dynamic settings, ideal for daytime viewing.

???{Natural}: Natural picture settings.

???{Standard}: Default settings that suit most environments and types of video.

???{Movie}: Ideal settings for movies.

???{Photo}: Ideal settings for photos.

???{Energy saving}: Settings that conserve the most energy.

4.4.Select your Preferred Sound Settings

1.While this display is playing video source, press button.

2.Press or button to select ???

, then press button.

3.Press or button to select an option, then press button:

???{Personal}: Apply your personalised sound settings.

???{Original}: Settings that suit most environments and types of audio.

???{Movie}: Ideal settings for movies.

???{Music}: Ideal settings for listening to music.

???{Game}: Ideal settings for games.

???{News}: Ideal settings for spoken audio, such as the news.

4.5.Play Multimedia Files

You can play videos, photos, and music on your display from:

???Your computer connected through your home network.

???A USB device connected to this display.

4.5.1. Play files from computer

To play files from computer, you will need:

???A wired home network, connected with a Universal Plug and Play (uPnP) router.

???Optional: A LAN cable that connects your display to your home network.

???A media server running on your computer.

???Appropriate settings on your computer firewall to allow you to run the media server.

Set up the network

1.Connect your display and the computer to the same home network. See page 9 for connecting your display to a network.

2.Switch on your computer and the router.

NOTE: If the apparatus does not return to DLNA mode due to external electrical disturbances (e.g. electrostatic discharge), user intervention is required.

Set up media sharing

1.Install a media server on your computer to share media files.These are some media servers:

???For PC:Windows Media Player 11 (or higher) or TVersity

???For Mac:Twonky

2.Switch on media sharing on your computer using the media server. For more information on how to set up the media server, refer to the website of the media server.

Play files

1.Press button.

2.Select [Browse network], then press button.

3.Select a file from the content browser, then press button to start playing.

4.Press the Play buttons on the remote control to control playing.

Tips:

???Select the top bar to filter your files by type.

???Select [Sort] to arrange the files by album name, artist, or other fields.

???To clear the list of offline media servers, press button, then select [Clear offline servers] and press button.

4.5.2. Play multimedia files from USB device

This display can play music, movie, or photo files from your USB device.

1. Connect your USB device to the USB port on this display.

USB

2. Press button, select USB, then press button.

3. The connected USB device is detected automatically for all its playable files, which will be automatically sorted into 3 types:

, , and .

Help

4. Press the BACK button to go up to the top layer in the screen. Press button to select the file type. Press button to enter its play list.

5. Select the file you want. Press button to start playing.

6.Follow the on-screen instruction to control the play option.

7.Press the PLAY buttons (H F G I J) to control playing.

Supported file system:

???FAT32

Supported file format:

???Music: MP3,WMA, M4A, AAC, AC3

???Movie: AVI, MP4, MOV, MPG/MPEG

???Photo: JPEG, BMP, GIF

Caution:

???The manufacturer is not responsible if the USB device is not supported, nor is it responsible for damage to or loss of data in the device.

BDL4620QL

???Do not overload the USB port. If you connect a USB storage device that consumes more than 500mA power, make sure that it is connected to its own external power supply.

4.6.Play options

4.6.1. Playing music files

1.Select Music in the top bar.

2.Select one music track, then press button.

???To play all the tracks in a folder, select one music file, then select

{Play All}.

???To skip to the next or previous track, press or button.

???To pause the track, press button. Press button again to resume playback.

???To skip backward or forward 10 seconds, press or button.

???To search backward or forward, press Gor J button, press repeatedly to toggle between different speeds.

???To stop the music, press H button.

Music options

While you play music, press button, then press button to select an option:

???{Repeat}: Select {Repeat} to play a track or an album repeatedly, or select {Play once} to play a track once.

???{Media Server}:When you play content from a media server, you can select another media server.

???{Shuffle On} / {Shuffle Off}: Enable or disable random play of tracks.

NOTE: To view information about a song (for example, title, artist or duration), select the song, then press button.To hide the information, press button again.

2. Select a video, then press button.

???To play all the videos in a folder, select one video file, then select

{Play All}.

???To skip to the next or previous video, press or button.

???To pause the video, press button. Press button again to resume playback.

???To skip backward or forward 10 seconds, press or button.

???To search backward or forward, press Gor J button, press repeatedly to toggle between different speeds.

???To stop the video, press H button.

Movie options

While playing video, press button, then press button to select an option:

???{Subtitles}: Select the available subtitle settings.

???{Subtitle Language}: Select the language for subtitles if available.

???{Character Set}: Select the correct character set for the subtitles.

???{Audio Language}: Select an audio language.

???{Repeat}: Select {Repeat} to play the video file repeatedly or {Play once} to play the video file once.

???{Media server}:When you play content from a media server, you can select another media server.

???{Shuffle On} / {Shuffle Off}: Enable or disable random play of video files.

???{DivX(R) VOD}: Display the DivX registration and deregistration codes for this display.

NOTE: To view information about a video (for example, played position, duration, title, or date), select the video, then press button.To hide the information, press button again.

Start a slideshow

If there are multiple photos in a folder, select a photo, then select {Play All}.

???To skip to the previous or next photo, press or button, and then press button.

???To stop the slideshow, press H button.

Slideshow options

While you play a slideshow, press button, then press button to select an option:

???{Shuffle Off} / {Shuffle On}: Enable or disable random display of pictures in the slideshow.

???{Repeat}: Select {Repeat} to watch a slideshow repeatedly or {Play once} to watch once.

???{Slideshow Time}: Select the displaying time for each photo in the slideshow.

???{Slideshow Transitions}: Select the transition from one photo to the next.

???{Media Server}:When you play content from a media server, you can select another media server.

1.Press button to display the OSD menu.

2.Press , or button to select {Setup}. Pressbutton to enter.

1. Press button to display the OSD menu.

2. Press[] [] [] or [ ] button to select menu item or adjust its value.

3.Press button to confirm menu selection and enter its submenu.

4.Press button to exit the OSD menu.

5.1.Quick Picture and Sound

Setup

Source

You can select picture and sound settings with the help of the settings assistant, which demonstrates the effect of your chosen setting immediately.

3.Press , , , or button to select {Quick picture and sound}, {Settings}, {Connect to network}, or {Network settings}. Press button to enter.

4.Press , , , or button to select its menu item or to adjust its value. Press button to confirm.

5.Press button to go back to the previous menu layer.

6.Press button to exit the OSD menu.

1.Press button to display the OSD menu.

2.Select {Setup}. Press button.

3.Select {Quick picture and sound}. Press button.

4.Select {Continue}, then press button

5.Follow the on-screen instructions to choose your preferred settings.

5.2.Settings

5.2.1. Picture menu

Picture style

Select a predefined picture setting.

Restore style

Restore the last-selected predefined picture setting.

Backlight contrast

Adjust the brightness of this display???s backlight.

Colour

Adjust the colour saturation of the picture.

Sharpness

Adjust the sharpness of the picture.

Noise reduction

Select the amount of noise reduction for the picture.

MPEG artifact reduction

Smoothen transitions and haziness in the digital picture.

Digital Crystal Clear

Fine-tune each pixel to match surrounding pixels and produce a brilliant, high-definition image.

???{Advanced sharpness}: Enable superior sharpness, especially on lines and contours in the picture.

???{Dynamic contrast}: Dynamically enhance the details in the dark, medium and light areas of the picture.

???{Dynamic backlight}: Select a backlight level to optimise dynamic power consumption and picture contrast.

???{Colour enhancement}: Dynamically enhance the vividness and details of colours.

Advanced

Access advanced settings such as gamma, tint settings and video contrast settings.

???{Gamma}: Adjust the non-linear setting for picture luminance and contrast.

???{Tint}: Change the colour balance.

???{Custom tint}: Customise colour balance setting. Only available if {Tint} ??? {Custom} is selected.

???{Video contrast}: Adjust video contrast.

???{Brightness}: Adjust screen brightness.

Game or computer

When viewing content from a connected game console, select {Game} to apply game settings.When a computer is connected through HDMI, select {Computer}.

Make sure that {Format and edges} ??? {Picture format} ??? {Unscaled} is selected so as to view maximum detail.

Format and edges

Access advanced settings to control the displaying format of the picture.

???{Picture format}: Change the picture format.

???{Screen edges}: Change the picture size.

???{Picture shift}: If available, move the position of the picture.

5.2.2. Sound menu

Sound style

Access predefined sound settings.

Restore style

Restore the last-selected predefined sound setting.

Bass

Adjust the bass level of the speaker and headphones.

Treble

Adjust the treble level of the speaker and headphones.

Surround mode

Select a surround sound mode to enhance your audio experience.

Audio out

Adjust audio output volume.

Advanced

Access advanced settings to enhance your audio experience.

???{Auto volume leveling}: Enable the reduction of sudden volume changes.

???{Speaker settings}:Turn on or off the internal speakers.

???{Clear sound}: Enhance sound quality.

???{Audio out format}: Select the type of audio output through the digital audio output connector.

???{Audio out leveling]: Set the output level for stereo audio. Select {Less} for a certain amount of loss in intensity or signal strength. Select {More} for no loss in intensity or signal strength.

???{Audio out delay}: Automatically sync the image on this display to the audio from a connected home theatre.

???{Audio out offset}: Adjust the setting for audio output delay. Available if {Audio out delay} is switched on.

5.2.3. General settings menu

Menu language

Select language used for OSD menus.

Monitor id

Set the ID number for controlling this display via the RS232C connection. Each display must have a unique ID number when multiple sets of this display are connected.

Eco mode

Set this display to reduce the power consumption automatically.

Auto search

Choose to let this display detect and display available signal sources automatically.

Clock

Adjust clock settings.

USB scheduling

This function allows you to program up to 3 different scheduled time intervals for this display to activate, and auto play USB media file of your setting.

After changing the {Clock} option in the {General settings} menu, you need to set this {USB scheduling} again.

Sleep timer

Switch off this display after a specified time.

Auto switch off

Set the time for this display to be switched off after a period of no activity. Press any key on the remote control to disable this function.

Local KB lock

Choose to enable or disable the keyboard (control buttons) function of this display.

???{Unlock}: Enable the keyboard function.

???{Lock all}: Lock all keyboard function.

???{Lock but volume}: Disable all the keyboard function except the and button.

???{Lock but power}: Disable all the keyboard function except the button.

RC lock

Choose to enable or disable the button function of the remote control.

???{Unlock}: Enable the button function.

???{Lock all}: Lock all button function.

???{Lock but volume}: Disable all the button function except the button.

???{Lock but power}: Disable all the button function except the button.

NOTE: To disable the lock function from [Local KB lock] or [RC lock] item, press buttons 1 9 9 8 on the remote control.

Factory settings

Reset all your customized settings to the factory defaults.

5.3.Network Settings

View network settings

Network settings

Static IP Configuration

Digital Media Renderer ..

View network settings

View connected network status.

Network settings

Select how this display should assign addresses to the network resources.

Static IP Configuration

Assign {IP address}, {Netmask}, {Gateway}, {DNS1}, and {DNS2} for this display.

Digital Media Renderer - DMR

Receive multimedia files from Smart Phones or Tablets connected to your network.

7.1.Pixels and Sub-pixels

subpixel

pixel

A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and blue. Many pixels together form an image.When all sub-pixels of a pixel are lit, the three colored sub-pixels together appear as a single white pixel.When all are dark, the three colored sub-pixels together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as single pixels of other colors.