Philips_Garage_Door_Opener

General

Do not insert the power plug in a wall socket or hang the TV to the wall before all connections are made.

???Place or hang the TV wherever you want, but make sure that air can circulate freely through the ventilation slots.

??? Do not install the TV in a confined space such as a book case or a similar unit.

???To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be placed in the vicinity.

???Avoid heat, direct sunlight and exposure to rain or water.

???The equipment shall not be exposed to dripping or splashing.

Examples of stationary images (this is not an all- inclusive list, you may encounter others in your viewing):

???TV and DVD menus: listings of DVD disk content;

???Black bars: when black bars appear at the left and right side of the screen, it is recommended to change to a picture format so that the picture fills the entire screen;

???TV channel logo: present a problem if they are bright and stationary. Moving or low-contrast graphics are less likely to cause uneven aging of the screen;

???Stock market stickers: presented at the bottom of the TV screen;

???Shopping channel logos and pricing displays: bright and shown constantly or repeatedly in the same location on the TV screen.

Examples of still pictures also include logos, computer images, time display, teletext and images displayed in 4:3 mode, static images or characters, etc.

Tip: reduce contrast and brightness when viewing.

Care of the screen

Do not touch, push or rub or strike the screen with anything hard as this may scratch, mar or damage the screen permanently.

And please do not rub with dust clothes with chemical treatment.

Do not touch the surface with bare hands or greasy cloth (some cosmetics are detrimental to the screen). Unplug the TV before cleaning the screen.

When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks. Do not use acetone, toluene and alcohol because they cause chemical damage. Do not use liquid cleaners or aerosol cleaners.Wipe off saliva or water drops as soon as possible.Their long time contact with the screen causes deformations and colour fading.

Stationary images on the TV screen

A characteristic of LCD and Plasma Panels is that displaying the same image for a long time can cause a permanent after-image to remain on the screen. This is called phosphor burn in. Normal use of the TV should involve the showing of pictures that contain constantly moving and changing images that fill the screen.

Electric, Magnetic and Electromagnetic

Fields (???EMF???)

???Philips Royal Electronics manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electro magnetic signals.

???One of Philips??? leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.

???Philips is committed to develop, produce and market products that cause no adverse health effects.

???Philips confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today.

???Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardisation for early integration in its products.

Downloaded From TV-Manual.com Manuals

Connect the antenna

<Insert the aerial plug firmly into the aerial socket x at the bottom of the TV.

Tip: for best quality use the suppressor cable supplied.

Connect the mains

< Insert the mains cord supplied into the mains at the bottom of the TV and in the wall socket.

Warning: verify that the mains supply voltage corresponds to the voltage printed on the sticker at the rear of the TV.

UK - EIRE

Remote control

<Insert the 2 batteries supplied (Type R6-1,5V).

Be sure the (+) and (-) ends of the batteries line up correctly (inside of case is marked.)

For most keys pressing a key once will activate the function.

Pressing a second time will de-activate it.

Downloaded From TV-Manual.com Manuals

BStandby

Press to switch the TV from or to standby mode.

When switched to standby, a red indicator on the TV lights up.

Attention: the TV is never powered off completely unless it is physically unplugged.

TV Press to select TV mode.

DVD STB VCR AUX

Press to select one of the system modes in which the remote control can be used.

See Audio and Video equipment keys, p. 51.

DEMO Press to switch the Demo menu on or off.

Colour keys

- When functions are attached to the colour keys, the colour keys are shown on screen.

- To select a page in Teletext mode.

OPTION

- To open and close the Quick access menu which contains a few frequently used options, like Picture format.

- When in teletext, press repeatedly to enlarge the teletext page display. See Teletext, p. 38.

aTo open and close the Electronic Programme Guide. See EPG (Electronic Programme Guide), p. 32.

Cursor keys

Press the cursor keys up/down, left/right to navigate through the menus.

OK - To activate a setting

- Starts playing content in the Multimedia Browser application.

BROWSE/MENU:

To open and close the main menu. See How to navigate through the menus, p. 11.

bTeletext On/Off

Press to switch teletext on. See Teletext, p. 37.

Only for UK: Digital text/Interactive television.

Attention: not all channels transmit interactive television applications at all times.

VVolume

Press + or - to adjust the volume.

??Mute key: interrupt the sound or restore it.

Downloaded From TV-Manual.com Manuals

The OPTION key allows you to display the Quick access menu which will give you direct access to some features and menu options.

1.Press the OPTION key.

> The Quick access menu appears.

2.Press the cursor up/down to select a menu item.

3.Press the OK key to jump to the selected menu item in the TV menu. (Except for the Clock option).

4.Use the cursor keys to make a selection.

5.Press the OPTION key to exit.

Note: digital related menu items will only be accessible in case of digital TV broadcasting.

Digital audio language:

See Adjust sound menu settings, p. 17.

Digital subtitle language:

See Adjust feature menu settings, p. 19.

Subtitles:

See Adjust feature menu settings, p. 19.

Picture format:

See Use of the TV menu settings,Adjust picture menu settings, p. 16.

Equalizer:

See Use of the TV menu settings,Adjust sound menu settings, p. 17.

Clock:

<Select to activate/deactivate the clock display on the screen.

Keys at the left side of the TV

In case your remote is lost or broken, apart from channel selection and volume adjustment, you can still change some of the basic settings with the keys at the side of your TV.

<Press the power switch B to switch the TV on or off.

The MENU key can be used to summon the TV menu without the remote control.

<Use:

-the VOLUME - and + keys and the PROGRAM/CHANNEL - and + keys to select menu items;

-the MENU key to confirm your selection.

Downloaded From TV-Manual.com Manuals

Introduction: Digital TV

Next to analogue broadcast reception, your TV has a built-in TV tuner which receives, decodes and displays digital terrestrial signals.

Digital TV and radio channels are only available and reproduced:

-when Digital Video Broadcasting Terrestrial (DVB-T) is applicable in your local area;

-and if DVB-T signal is supported by your TV for the country you live in. See www.philips.com/support for the list of supported countries.

Switch the TV on

<Press the power switch B at the side of the TV.

>An indicator on the front of the TV lights up and the screen comes on.

<If the TV is in standby mode, press the -P+ keys or the B key on the remote control.

Note: the first time (and only the first time) you switch on your TV, you see a Welcome screen followed by the installation procedure. See First time installation, p. 9.

First time installation

The first time (and only the first time) you switch on your TV, you see a Welcome screen followed by the installation procedure.

The installation procedure consists of a series of screens that will guide you through the installation of your TV.

Follow the instructions on screen.

Note: if the TV has already been installed before and/or you want to change the First time installation settings, proceed with Use of the TV menu settings, p. 13.

Downloaded From TV-Manual.com Manuals

This will help you to install the following sections:

Television

Settings assistant

PHILIPS Television

System searching: please wait..........

Step 1: select your on-screen language

After the Welcome screen you are asked to select a language of the TV's on-screen menus.The text of the header and the info on screen continuously change language. Also the digital audio and subtitle language will be set to the selected menu language.

1.Press the cursor up/down to highlight your language.

2.Press the OK key on the remote control.

3.Follow the instructions on screen to proceed.

Step 2: complete the initial TV installation procedure

1.Press the green colour key on your remote control when Television is highlighted.

2.Select the country where you are now located.

Notes:

-if you select a wrong country, the channel numbering will not be according to the standard for your country.

-in case the country selected is not DVB-T supported by your TV, digital related menu-items will not be accessible.

3.Press the green colour key on your remote control to start the Automatic channel installation.

>All available digital TV and radio channels and analogue TV channels are searched for and stored automatically. This will take a few minutes.When the search is complete, the menu will indicate the number of digital and analogue channels found.

Notes:

-reception of digital terrestrial TV channels is applicable dependent on the country selected;

-if you choose to install the channels at a later time, select the Automatic installation in the TV menu, Installation, Channels to scan available channels.

4.Press the red colour key again when the search is completed.

Downloaded From TV-Manual.com Manuals

PHILIPS Installation

This will help you to complete the Settings assistant.

Television

Settings assistant

PHILIPS Settings assistant

Please select your location before

continuing:

Home

Shop

Step 3: Settings assistant: select your TV settings

By means of several split screens/full screens you are prompted to select your preferred Picture and Sound settings, to finally arrive at a complete setting which satisfies you.

1.Press the green colour key on your remote control to enter the Settings assistant menu.

2.Select your Location with the cursor up/down.

>If you choose Shop it will skip the Settings assistant. The TV parameters for Picture and Sound will then be set to predefined fixed settings.

Press the green colour key again to proceed.

>If you choose Home it will display the Settings assistant.

3.Use the cursor left/right to each time select your preferred screen.

4.Press the green colour key to each time confirm your selection and to jump to the following screen.

>The following items will be presented sequentially.

In the header it is mentioned how many screens have been completed and how many screens there are in total.

The Settings assistant will step sequentially through the following settings: Picture and Sound.

5.Press the green colour key again to store all the settings and to return to the TV installation menu.

Note: when you skip or stop the Settings Assistant, then the standard settings Philips selected for you will be chosen.

6.Press the green colour key again to finish the First time installation procedure and to display the first stored TV channel.

Note: any time you can change or reset your settings or adjust individual settings for Picture and Sound in the TV settings menu. See p. 13, Use of the TV menu settings.

To control the settings of special TV functions, features and accessory equipment, see p. 19, Adjust feature menu settings.

Downloaded From TV-Manual.com Manuals

A lot of guiding instructions, help texts and messages will be displayed on your TV when you use the menus or when you try to execute an action.

Read the help texts which are being displayed on the specific item highlighted.

The colour keys at the bottom of the screen refer to the different actions which may be executed.

Press the corresponding colour key on the remote control to perform the required or desired action.

Note: digital related menu items will only be accessible in case of digital TV broadcasting.

1.Press the MENU/BROWSE key on the remote control.

>The main menu appears on the screen.

-TV menu allows you to access the TV menu. See below.

-TV channels allows you to access the TV channel list and to create up to four favourite lists with your preferred TV channels and digital radio stations. See Create your favourite channel list, p. 31.

-Programme guide allows you to access detailed information about individual digital TV programmes. According to the type of Electronic Programme Guide, it also allows you to access the table of scheduled Digital TV programmes and easily select and tune to a desired programme.

See EPG, Electronic Programme Guide, p. 32.

-Multimedia allows you to access the Multimedia browser application. It lets you display your personal multimedia files. Multimedia is only present when a USB device is connected.

See Multimedia browser, p. 34.

2.Use the cursor up/down to highlight and select a menu item.

3.Use the cursor right to enter the highlighted menu item.

>The right panel shows the content of the highlighted menu item.

Downloaded From TV-Manual.com Manuals

Use of the TV menu settings

The TV menu allows you to access and change settings and preferences in case you want to change the First time installation settings and/or you want to control the settings of special TV functions, features and peripheral equipment.

Adjust Picture and Sound settings

1.Press the MENU/BROWSE key on the remote control.

>The main menu appears on the screen.

2.Select TV menu and press the cursor right.

>The TV menu is displayed.

3.Select TV settings and press the cursor right.

>The TV settings menu is moved to the left.

4.Press the MENU/BROWSE key to exit the menu.

To make it easier to change the settings of the TV, there are 3 ways of doing it. See next page.

Downloaded From TV-Manual.com Manuals

A.Change settings in an easy-to-use manner with the Settings assistant.

Each time you've made a selection, press the green key to confirm your selection.

1.Select Settings assistant and press the cursor right.

>By means of several split screens/full screens you are prompted to select your preferred Picture and Sound settings to finally arrive at a complete setting which satisfies you.

See First time installation, Step 3: Settings assistant: select your TV settings, p. 10.

2.Press the green colour key to return to the TV menu again.

B.Use of the Standard settings (if present)

<Select Picture or Sound and press the cursor right.

>A menu appears which allows you to fine tune the Picture and Sound settings.

>To adjust the Picture settings, see Adjust picture menu settings, p. 14.

>To adjust the Sound settings, see Adjust sound menu settings, p. 17.

Downloaded From TV-Manual.com Manuals

The picture menu contains the settings that affect the quality of the picture.

1.Press the MENU/BROWSE key on the remote control.

>The main menu appears.

2.Select TV menu and press the cursor right.

>The TV menu is moved to the left.

3.Select TV settings and press the cursor right.

>The TV settings menu is moved to the left panel.

4.Select Picture and press the cursor right.

>The Picture menu is moved to the left panel.

5.Use the cursor up/down to select the Picture menu items.

6.Press the cursor right to enter the selected Picture menu item.

Note: all digital related menu items will only be accessible in case of digital TV broadcasting.

7.Use the cursor keys to adjust the settings.

8.Press the cursor left to return to the Picture menu.

Contrast

Adjusts the intensity of bright parts in the picture but keep the dark parts unchanged.

Brightness

Adjusts the light output of the complete picture, which will mainly affect the darker areas of the picture.

Colour

Adjusts the saturation level of the colours to suit your personal preference.

Hue

Compensates for the colour variations in NTSC encoded transmissions.

Sharpness

Adjusts the sharpness of fine details in the picture.

Tint

Increases or decreases Warm (red) and Cool (blue) colours to suit personal preferences.

<Select Cool to give the white colours a blue, Normal to give the white colours a neutral, Warm to give the white colours a red tint.

<Select Custom to make a customised setting in the Custom tint menu item.

Downloaded From TV-Manual.com Manuals

TV menu

Custom tint (only when Tint is set to Custom)

Fine tunes the white point (WP) and black level (BL) of the picture.

1.Select Custom tint and press the cursor right.

2.Use the cursor keys to select and adjust the settings of: R-WP: allows you to customise the colour tint by adjusting the red whitepoint of the picture.

G-WP: allows you to customise the colour tint by adjusting the green whitepoint of the picture.

B-WP: allows you to customise the colour tint by adjusting the blue whitepoint of the picture.

R-BL: allows you to customise the colour tint by adjusting the red blacklevel of the picture.

G-BL: allows you to customise the colour tint by adjusting the green blacklevel of the picture.

3.Use the colour keys to reset to the predefined settings.

4.Press the cursor left to return to the Picture menu.

Pixel Plus

Pixel Plus is the most ideal setting, as it fully processes the image to make every single pixel the best it can be, improving contrast, sharpness, picture depth, and colour reproduction and brilliance from every source, including High Definition.

<Select On or Off to activate/de-activate Pixel Plus.

Digital Natural Motion

Reduces the field and line flicker and reproduces smooth movement especially in movies.

<Select Off, Minimum or Maximum in order to activate/de-activate Digital Natural Motion and to really see the difference in picture quality.

ClearLCD

ClearLCD results in superior sharpness of motion reproduction, better black level, high contrast with a flicker- free, quiet image and a larger viewing angle.

<Select On or Off.

Dynamic contrast

Automatically makes the contrast in the darker and the brighter picture areas more noticeable as the image on the screen changes.

<Normally select Medium. It may be preferred to select

Minimum, Maximum or Off.

DNR

DNR automatically filters out and reduces the image noise. This improves picture quality when receiving weak signals.

<Select Off, Minimum, Medium or Maximum according to the image noise in the picture.

Downloaded From TV-Manual.com Manuals

Movie expand 16:9 Wide screen

Picture format

This allows you to adjust the size of the picture dependant on the broadcasted format and your preferred setting. How to navigate through the TV settings menu, see p. 12: Use of the TV menu settings.

Tip: this function is also accessible via the OPTION key on the remote control.

Choose among the following picture formats:Auto format, Super zoom, 4;3, Movie Expand 14:9, Movie Expand 16:9 or Wide screen.

Auto format makes the picture fill the screen as much as possible.

In case of subtitles in the bottom black bar,Auto format makes the subtitles visible.

In case of a broadcaster logo in the corner of the top black bar, the logo disappears from the screen.

Super zoom removes the black bars on the sides of 4:3 programmes with minimal distortion.

When in Movie Expand 14:9, Movie Expand 16:9 or Super zoom screen format, you can make subtitles visible with the cursor up/down.

Note: with HD sources not all picture formats will be available.

Downloaded From TV-Manual.com Manuals

The sound menu contains the settings that affect the quality of the sound.

1.Press the MENU/BROWSE key on the remote control.

>The main menu appears.

2.Select TV menu and press the cursor right.

>The TV Menu is moved to the left.

3.Select TV settings and press the cursor right.

>The TV settings menu is moved to the left panel.

4.Select Sound and press the cursor right.

>The Sound menu is moved to the left panel.

5.Use the cursor up/down to select the Sound menu items.

6.Press the cursor right to enter the selected Sound menu item.

Note: dependent on the input signal, one or more menu items may not be selectable.

7.Use the cursor keys to adjust the settings.

8.Press the cursor left to return to the Sound menu.

Equalizer

Allows you to change the frequency response of the sound to match your personal taste.

Tip: this function is also accessible via the OPTION key on the remote control.

Volume

Allows you to adjust the sound output level.

Balance

Allows you to adjust the output of the right and left speakers to obtain the best stereo reproduction for your listening position.

Digital audio language (only with Digital TV broadcasting)

Allows you to select an audio language out of the list of the available broadcasted languages for the current digital programme.

Note: if there is more than one variant for an audio language, then select one of the variants.

To permanently change the audio language, use the Language menu in the Installation menu.

Tip: this function is also accessible via the OPTION key on the remote control.

Downloaded From TV-Manual.com Manuals

The Features menu allows you to control the settings of special TV functions, features and accessory equipments.

1.Press the MENU/BROWSE key on the remote control.

>The main menu appears.

2.Select TV menu and press the cursor right.

>The TV Menu is moved to the left.

3.Select Features and press the cursor right.

>The Features menu is moved to the left panel.

4.Use the cursor up/down to select the Features menu items.

5.Press the cursor right to enter the selected Features menu item.

6.Use the cursor keys to adjust the settings.

7.Press the cursor left to return to the Features menu.

Subtitle

This displays Teletext and DVB-T subtitles from the selected TV channel.These can be permanently displayed, or only when mute is active.The teletext subtitle page of analogue channels must be stored for each TV channel.

1.Switch on teletext and select the proper subtitle page from the index.

2.Switch off teletext.

3.Select

-Subtitle On to display the subtitles on the selected TV channels.

-On during mute to automatically display the subtitles only when the sound has been muted with the ?? key on the remote control.

Tip: this function is also accessible via the OPTION key on the remote control.

Digital subtitle language (only with Digital TV broadcasting)

This allows you to (temporarily) select your preferred subtitle language out of the list of the broadcasted languages for the current programme.

Note: to permanently change the subtitle languages, use the Language menu in the Installation menu.

<Use the cursor up/down to temporarily overrule your permanent language selection and confirm with the OK key.

Tip: this function is also accessible via the OPTION key on the remote control.

Downloaded From TV-Manual.com Manuals

1.Select Childlock.

2.Press the cursor right to enter the Childlock menu.

3.Enter your 4-digit code.

Note: you have to re-enter your code each time you enter the Childlock menu.

4.Select one of the menu items of the Childlock menu and press the cursor right:

-Lock to lock all channels and externals:

-Custom lock to lock a certain programme or to lock all the channels from a certain time.

<Select:

-Lock after to lock all programmes from a certain time onwards.

<Press the cursor right twice.

<Select On to set the lock.

<Press the cursor left.

<Select Time and press the cursor right.

<Enter the time with the cursor up/down and right.

- Channel lock to lock a certain TV channel or external.

<Press the OK key to activate/deactivate.

-Parental rating to set an age rating to a digital programme if the programme is parental rated.The ratings applied are according the selected country in the initial installation.

<Press the cursor right and select an age rating with the cursor up/down.

-Select Unlock to disable all locks you have set.

Important: you have forgotten your code !

1.Select Change code and press the cursor right.

2.Enter the overriding code 8-8-8-8.

3.Enter a new personal 4-digit code.

4.Confirm your new entered code.

>The previous code is erased and the new code is stored.

Downloaded From TV-Manual.com Manuals

1.Select On timer.

2.Press the cursor right to enter the On timer menu.

3.Select Timer and press the cursor right.

4.Select On.

5.Select Channel and then the TV channel you want your TV to switch to on a selected time and day

6.Select Day and then a day of the week or select Daily.

7.Select Time and enter the time with the digit keys or with the cursor up/down.

8.Press the OK key to activate.

9.Press the cursor left to return to the Features menu or press the MENU/BROWSE key to switch off the menu.

Note: From now on, every week, your TV will automatically switch to the selected channel, on the selected day, at the selected time, until the On timer function is switched off again.

Downloaded From TV-Manual.com Manuals

Tip: you will need this chapter only if you want to change the installation settings.

Installation menu

This menu will adjust settings related to the installation of the TV channels, language and country and to the initial installation of your TV.

1.Press the MENU/BROWSE key on the remote control.

>The main menu appears.

2.Select TV menu and press the cursor right.

>The TV Menu is moved to the left.

3.Select Installation and press the cursor right.

>The Installation menu is moved to the left panel.

4.Use the cursor up/down to select the Installation menu items.

5.Press the cursor right to enter the selected Installation menu item.

6.Use the cursor keys to make a selection.

7.Press the OK key to activate or to confirm.

8.Press the cursor left to return to the Installation menu or press the MENU/BROWSE key to switch off the menu.

Select your language preferences

This menu allows you to select your preferred language for menu, audio and subtitle.

Menu language

This allows you to select your menu language out of the list of the available languages.

Preferred audio language (only with Digital TV broadcasting)

This allows you to select your audio language preference in case several languages are broadcasted.

Preferred subtitle language (only with Digital TV broadcasting)

This allows you to select your subtitle language preference in case several languages are broadcasted.

Hearing impaired (only with Digital TV broadcasting)

This allows you to select the hearing impaired audio or subtitle language.

When set to On, the Hearing impaired version of your preferred audio or subtitle language will, if available, be reproduced.

When set to Off, the normal audio and subtitle language behaviour will be applicable.

Downloaded From TV-Manual.com Manuals

Select your country

This allows you to select the country where you are now located.

Notes:

-if you select a wrong country, the channel numbering will not be according to the standard for your country;

-in case the country selected is not DVB-T supported by your TV, digital related menu-items will not be accessible.

Select the time zone (only with digital TV broadcasting)

Only applicable for certain countries and dependent on the selected country.

This allows you to select your local time zone so that the clock display shows the correct time.

Downloaded From TV-Manual.com Manuals

Analogue: manual installation

This gives you the possibility to manually install (tuning-in channel by channel) analogue channels. Manual installation will not find nor store any DVB-T (digital) channels.

1.Select Analogue: manual installation and press the cursor right.

2.Select System.

3.Select your country or part of the world where you are now located.

4.Select Search and press the cursor right.

5.Select the red or green colour key to proceed.

Tip: if you know the frequency, enter the 3 digits of the frequency with the digit keys 0 to 9 (For example, 049).

6.Press the cursor left to store the channel found or to search for another channel.

7.Select Fine tune and press the cursor right.

Fine tuning can be useful when the frequency has shifted a bit or when interference of another frequency occurs. Adjust the frequency with the cursor up/down in case of poor reception of the channel found.

8.Select Store current channel if you want to store the (fine tuned) frequency under the current channel number. Press the cursor right and confirm with the OK key. Select Store as new channel if you want to store the (fine tuned) frequency under a new channel number. Press the cursor right and confirm with the OK key.

9.Use the rearrange menu to rename or reshuffle the channels. See next page.

Note: when on a frequency where a DVB signal is broadcasted, the tuner will try to decode an analogue TV channel, and hence will not show video.

Downloaded From TV-Manual.com Manuals

<Select Teletext 2.5 On to take advantage of this feature.

<Select Teletext 2.5 Off if you like the more neutral teletext layout.

>The selection made is valid for all the channels which broadcast Teletext 2.5.

Note: it may take a few seconds before teletext broadcast switches over to Teletext 2.5.

Select the On Screen Display (OSD)

This allows you to select the display of the volume bar and a reduced or extended on screen display of programme and channel information.

<Select Minimum to activate the display of reduced channel information.

<Select Normal to activate the display of extended channel and programme information. For example, information on the programme, input signal quality of connected peripheral equipment, the screen format and sound mode, selected audio language, subtitle language, ratings, remaining time of the sleeptimer setting,...

Display a Programme title

This allows you, to display the programme title according to the transmitted information.

>When selected Yes, after the selection of a TV programme or after you press the i key on the remote control, a programme title will be displayed if transmitted.

>When selected No, the programme title will only appear after you press the i key and not after the selection of a channel.

Downloaded From TV-Manual.com Manuals

This allows you to reset most of the predefined factory states.

1.Select and press the cursor right.

2.Press the OK key to erase settings and reset them to their default values.

<Press the red colour key on your remote control if you want to be reminded later on.

<Press the green colour key on your remote control to confirm you have read the message.

>Once you have confirmed, the message will not pop up again.

If however, you want to see the last broadcasted announcement again, select Announcement in the Software upgrade menu.

Note: as long as the software upgrade has not been executed, the message will be available.

Downloaded From TV-Manual.com Manuals

All channels

EXT1

EXT2

HDMI

A1 Analogue channel 1

2 Digital channel 1

3 Digital channel 2

Change list

Tune to a channel by pressing OK. Use -P+ for page up/down.

All channels

All

TV channels

Radio channels

AAnalogue Favourites 1 Favourites 2

This allows you to select up to four favourite channels lists with your preferred TV channels and radio stations. For example, each member of your family can create his/her own favourite list.

In addition to the favourite channel lists you may also select a list with only digital TV channels or a list with only the radio channels or a list with only the analogue channels.

Note: when this key is pressed the first time after you have finished the installation, it will bring up the full channel list. In other situations it will bring up the last selected channel list.

To select a channel from the displayed favourite list

1.Press the FAV key (or the OK key).

> The last selected channel list appears.

2.Use the cursor up/down to select a channel.

3.Press the OK key to display the selected channel.

To select another favourite channel list

1.Press the FAV key.

> The last selected channel list appears.

2.Press the red colour key to bring up the list of possible favourite channel lists.

3.Use the cursor up/down to select a list.

4. Press the OK key.

5. Press the FAV key again to exit.

To create a favourite list or to modify the list

1. Press the FAV key.

> The last selected channel list appears.

2.Press the red colour key.

>A list with all possible favourite channel lists appears.

3.Use the cursor up/down to select a Favourites (1 to 4) channel list.

4.Press the OK key.

5.Press the green colour key to enter the Edit mode.

>The selected Favourite list will bring up a full channel list.

6.Use the cursor up/down to select a channel.

7.Press the OK key to check or uncheck the highlighted channel and to add it to or remove it from your selected

favourite list.

8a. < Press the green colour key again to leave the Edit mode.

>The modified favourite channel list appears. < Press the FAV key again to exit.

>With the ???P+ key you will be able to browse through the TV channels of the selected list.

8b. Press the red colour key to remove the channel list.

Note: with the digit keys you can still select channels which are not marked as favourite.

Downloaded From TV-Manual.com Manuals

To select only TV or only radio channels on the All channels list

When the All channels list is displayed or selected you may filter the list and select a list with only the TV channels or a list with only the radio channels.

1.Press the FAV key.

>The last selected channel list appears.

2.Press the cursor left.

3.Select the All channels list and press the cursor right.

4.Press the red colour key to filter.

5.Select your desired channels list.

6.Press the FAV key again to exit.

>With the ???P+ key you will be able to browse through the TV channels of the filtered list.

Note: the filtering will not be remembered after the TV is switched off or set to standby.

EPG (Electronic Programme Guide) (only with Digital TV channels)

TV channels

Programme Guide

The Electronic Programme Guide shows you detailed information about the current programme and also about the next programme (only for TV programmes that provide EPG information).

Note: these instructions may differ according to the type of Electronic Programme Guide.

1.Press the a key.

>The EPG screen appears. Dependent on conditions it may take some time to acquire EPG data.

>The EPG screen updates automatically if the EPG data is acquired successfully. If not, the EPG screen remains blank.

>Information about the selected programme appears.

<Use the coloured keys to activate the available EPG features displayed at the bottom of the screen.

2.To quit the Electronic Programme Guide, press the a key again.

When the type of Electronic Programme Guide available, displays a list of TV programmes (for UK only):

1.Use the cursor up/down to select a desired TV programme. > Information about the selected programme appears.

Tips:

-press the blue colour key on the remote control to view more information (not currently displayed) about the selected programme.

-to quit the display of detailed information, press the blue colour key again.

Downloaded From TV-Manual.com Manuals

Multimedia Browser

The Multimedia browser lets you display pictures, movies or play audio files stored on a USB device.The Multimedia browser application is invoked from the main menu.

-Following file formats can be reproduced: for pictures: JPEG

for audio: MP3, MP3 Pro, LPCM

for video: MPEG1, MPEG2

-Only FAT/DOS-formatted memory devices are supported.

-Philips can not be held responsible if your USB device is not supported.

To view content from a USB device

Tip: if your USB device does not fit into the USB connector at the side, use an USB extend cable to connect the USB device to the USB port. Ask your dealer for more information.

To insert a USB device

Note: USB devices are not supplied with this TV.

In case of a USB-memory stick or a digital camera, connect it to the USB connector at the side. See To make video and audio connections, Side panel overview, p. 41.

When a USB device is inserted, the Multimedia browser menu is displayed automatically. See further.

To remove the USB device

1.Press the MENU/BROWSE key on the remote control to switch off the main menu.

2.Remove the USB device.

Downloaded From TV-Manual.com Manuals

Multimedia Browser (Continued)

Function keys at the bottom of the screen

Note: to rotate a picture or to select one of the zoom magnifications, first stop the slide show with the OK key or the blue colour key.

Multimedia function keys on the remote control

?? to fast rewind displaying content

???to stop playing content

??- to play a single file, start a slide show, playback of a

folder or other collection - to pause playing content

??? to fast forward displaying content

Downloaded From TV-Manual.com Manuals

Note:Teletext is not available via equipment connected to the HDMI connector.

Most TV channels broadcast information via teletext. This TV has a 1200 pages memory that will store most

broadcasted pages and subpages to reduce waiting time. After each programme change, the memory is refreshed.

<Press b to switch the teletext on.

> The main index page appears on the screen.

Select a Teletext page

<Enter the desired page number with the digit keys or with the -P+ key.

<Select the options at the bottom of the screen with the colour keys.

Previous selected teletext page

<Press the 0 key.

Select T.O.P. teletext broadcasts

<Press i.

>A T.O.P. overview of the teletext subjects available is displayed.

<Select with the cursor up/down, left/right the desired subject and press the OK key.

Note: not all TV channels broadcast T.O.P. teletext.

Select subpages

When a selected teletext page consists of different subpages, a list of available subpages appears on the screen. Press the cursor left or right to select the next or previous subpage.

Picture/Teletext

1.Press the b key.

2.Press the b key to show Teletext on the right of the screen.

3.Press the b key to return to a full teletext picture.

4.Press the b key to return to a full screen picture.

Downloaded From TV-Manual.com Manuals

Hypertext

With hypertext you can quickly jump to a pagenumber or search for a specific word shown on the current teletext page.

1.Press the OK key to highlight the first word or a number on the page.

2.Use the cursor up/down, left/right to select any other word or number you want to search for.

3.Press the OK key to confirm.The search starts.

>A message appears at the bottom of the screen to indicate the searching, or that the word or page is not found.

4.Use the cursor up until the top of the page to exit hypertext.

Enlarge a Teletext page

<Press the OPTION key on the remote control repeatedly to display the upper teletext part, the lower teletext part and then to return to the normal teletext page size.

Teletext menu

The Teletext menu offers various functions to control teletext.

1.Switch teletext on and press the MENU/BROWSE key to activate the menu.

2.Press the cursor up/down to select the menu items.

3.Press the OK key to activate.

4.Press the MENU/BROWSE key to leave the teletext menu.

Reveal

Reveals/conceals hidden information on a page, such as solutions to riddles and puzzles.

Cycle subpages (if subpages are available)

Makes the subpages cycle automatically.

<Press the OK key to activate and to deactivate again.

Language

If the displayed characters on screen do not correspond with the characters used by the teletext broadcaster, you can change the language group here.

< Select Gr. I or Gr. II with the OK key.

Downloaded From TV-Manual.com Manuals

Digital text (only for UK)

Some digital channels offer dedicated digital text services (for instance BBCi).

1. Press b to switch Digital text on.

Note: UK only: digital text is displayed when programmes are carrying digital text or interactive services.

2.To use the digital text, follow the instructions on screen.

3.Depending on the service, you may be asked to use the cursor keys, the OK key, the coloured keys, the teletext key and sometimes the digit keys.

4.When you have finished watching teletext, select a different channel with the -P+ keys or follow the instructions on screen to return to picture.

5.Press ??? CANCEL to cancel the digital text or interactive services.

Text info

Some digital channels also offer information on the programme being broadcast. In that case a message may appear at the bottom of the screen for a few seconds. Follow the instructions on screen and use the cursor keys to scroll through the next pages.

Note: digital text will not be available when Subtitles are set to On in the Features menu.

Downloaded From TV-Manual.com Manuals

Tip: use the inputs that are available on your equipment that provide the best video or audio performance, as below.

Note: your TV comes with all types of connectors with the exception of the DVI connector but some of your equipment may be equipped with this type. In this case you'll need a DVI to HDMI adapter or a HDMI to DVI cable and separate audio cables, all available at your local dealer.

Warning: be sure to connect the DVI output connector first, then connect to the HDMI input on your TV.

Notes:

- cables are often colour-coded to connectors. Connect red to red, white to white....

- component video (YPbPr) connection is necessary to view video sources, for example digital broadcastings coming from a settop box, in 1080i, 720p, 576i, 576p, 480i or 480p,

- PC equipped with a VGA connector, see p. 47.

Downloaded From TV-Manual.com Manuals

3 1

USB

Camera, Camcorder, Game

1.Connect your camera, camcorder or game as shown.

2.Connect to VIDEO 2 and AUDIO L 3 for mono equipment. For stereo equipment also connect AUDIO R 3.

S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS cables with the S-VIDEO input 1 and AUDIO inputs

Warning: do not connect cable 1 and 2 at the same time.This may cause picture distortion !

Headphone

1.Insert the plug into the headphone socket L as shown.

2.The headphone impedance must be between 8

and 4000 Ohm.The headphone socket has a 3.5 mm jack.

In the Sound menu select Headphone volume to adjust the headphone volume.

Tip: Press ?? on the remote control to switch off the internal loudspeakers of the TV.

USB

See Multimedia browser, p. 34.

Downloaded From TV-Manual.com Manuals

Warning: do not place your recorder too close to the screen as some recorders may be susceptible for signals from the display. Keep a minimum distance of 0,5 m from the screen.

EXT 1/2

CABLE

ANTENNA

RECORDER

With a eurocable

1.Connect the aerial cables 1 and 2 as shown.

2.Connect the eurocable 3 as shown.

3.Make your selection of the source to which the VCR has been connected in the Installation menu, Select your connections, p. 29.

With the aerial cable only

1.Connect the aerial cables 1 and 2 as shown.

2.Tune in your recorder???s testsignal and store the testsignal under programme number 0.

See Analogue: manual installation, p. 26. See also the handbook of your recorder.

Connect a decoder and a VCR

Connect a eurocable 4 to your decoder and to the special euroconnector of your recorder. See also the handbook of your recorder.

Tip: you can also connect your decoder directly to EXT1 or EXT2 with a eurocable.

Downloaded From TV-Manual.com Manuals

Note: you can not record signals from equipment connected to the YPbPr input.

With aerial cables only

RECORDER RECORDER

1.Connect the aerial cables 1, 2 and 3 as shown.

2.Tune in your recorder???s testsignal and store the testsignal under programme number 0.

See Analogue: manual installation, p. 26. See also the handbook of your recorder.

Connect a satellite receiver

CABLE

EXT 1/2

With a eurocable

1.Connect the aerial cables 1 and 2 as shown.

2.Connect your satellite receiver to EXT1 or 2 with a eurocable 3.

3.Select the equipment you have connected in the Installation menu, Select your connections, p. 29, and link it to EXT1 or 2.

With Component Video connectors

See Connect a DVD player, a satellite receiver or a cable box, p. 46

Downloaded From TV-Manual.com Manuals

Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys.

HDMI

HDMI is the leading new standard for Digital video and audio interconnection.

1.Connect your equipment with the HDMI connector.

2.Select the equipment you have connected in the Installation menu, Select your connections, p. 29, and link it to HDMI 1 or 2.

Note: in case of any problems, see Annex 5: Issues referring to connected peripherals with a HDMI connector, p. 60.

Connect a DVD player or Cable box

Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys.

HDMI

With a DVI connector

Note: only a DVD player with DVI with digital sound can be connected to the HDMI connector.

HDMI

DIGITAL

1AUDIO

DVI

Downloaded From TV-Manual.com Manuals

Tip: if necessary, you can adjust the picture position to the centre of the screen with the cursor keys.

DVD / STB

With Component Video Connectors

1.Connect the three separate component video cables 1 to the YPbPr jacks on the DVD player and to the Y, Pb and Pr jacks of EXT3 on the TV.

2.Connect the audio cable 2 to the digital out of the equipment and to the DIGITAL AUDIO IN connector of the TV.

3.Select the equipment you have connected in the Installation menu, Select your connections, p. 29. Also select Digital audio in in the same Connections menu and link it to EXT3.

4.In case of a DVD player with analogue audio, connect the audio cable to the DVD???s audio L and R jacks and to the L/R AUDIO jack of

EXT3 3.

5.In case of a cable box and/or a satellite receiver also connect the cable TV cable and/or the satellite antenna cable 4 and the aerial cable 5.

ANTENNA 75

Notes:

-cables are often colour coded. Connect red to red, white to white, etc..;

-the labels for the component video sockets may differ depending on the DVD player connected. Although the abbreviations may vary, the letters

B and R stand for the blue and red component CABLE signals, respectively, and Y indicates the

luminance signal. Refer to the DVD player???s instructions for use for definitions and connection details;

-to get an optimal viewing, it is advised to switch your equipment to the highest possible supported display modes.

Downloaded From TV-Manual.com Manuals

Notes:

-only a PC with digital sound can be connected to the HDMI connection;

-if your PC does not have digital sound output, connect your PC via a VGA connector;

-before connecting your PC to the TV, select your PC monitor settings to a refresh frequency of 60 Hz;

-supported PC monitor modes:

AUDIO OUT DISPLAY SYNCHRONIZED

VGA

HDMI

DVI

PC equipped with a VGA connector:

1.Connect one end of a VGA cable 1 to the video card of the computer and the other end to the VGA connector at the bottom of the TV. Fix the connector firmly with the screws on the plug.

2.In case of a Multimedia computer, connect the audio cable 2 to the AUDIO outputs of your computer and to the L/R AUDIO input of the TV.

3.Select VGA in the Installation menu, Select your connections, p. 29 and link it to VGA.

4.Also select Analogue audio In in the same Connections menu.

PC equipped with a DVI connector: With Digital audio

1.Use a DVI to HDMI cable to connect to one of the HDMI connector of your TV 1.

2.Connect the audio cable 2 to the DIGITAL AUDIO IN connector of the TV.

3.Select the computer you have connected in the Installation menu, Select your connections,

p. 29 and link it to HDMI 1 or 2.

4.Also select Digital audio In in the same Connections menu.

With Analogue audio

1.Use a DVI to HDMI cable to connect to the HDMI 2 connector of your TV 1.

2.Connect the audio cable 3 to the L/R AUDIO input of the TV.

3.Select the computer you have connected in the Installation menu, Select your connections,

p. 29 and link it to HDMI 2.

4.Also select Analogue audio In in the same Connections menu.

Downloaded From TV-Manual.com Manuals

AUDIO OUT

EXT 1 / 2

Digital Home Cinema amplifier

<Connect a digital Home Cinema amplifier to the DIGITAL AUDIO OUT connector 1 at the bottom of the TV.

Tip: to avoid visible delay between picture and sound, use this DIGITAL AUDIO OUT connector to connect your Home Cinema amplifier.

Analogue Home Cinema amplifier

<According to the type of connector cables and the connector input available on your Home Cinema amplifier, connect your receiver to the AUDIO OUT L and R connectors 3 or to EXT1 or 2 2 at the bottom or the rear of the TV.

Downloaded From TV-Manual.com Manuals

Warning: switch off your TV before any module is inserted in the Common Interface slot.

COMMON INTERFACE

o o

TOP

To receive scrambled DTV signals you will need a CA (Conditional Access) module and a Smart card provided by the service provider.

A CA module can enable additional services, for example Pay TV.

Contact your Common Interface service provider to get more information about these modules. Although CA module types may vary dependent on the manufacturer, each one of the CA modules supports a certain kind of encryption system.Your TV supports CA modules to work with the DVB-T standard.

Note that a smart card may only be valid for a single broadcast channel.

CA modules and smart cards are neither supplied nor optional accessories from Philips.

The CA module is responsible for the messages and texts on screen. In case of failure or strange behaviour, you must call your CI service broadcaster.

Insert a CA module

<Insert the specified Conditional Access module into the Common Interface slot as far as it will go. It may take a few minutes before the CA module is activated and service information is downloaded.

Warning: when you connect the CA module incorrectly, it may damage the card and the TV. After inserting a card, leave it in the slot permanently. Do not remove it from the slot unless asked to do so. For example, your card has to be in the slot when your CI service broadcaster wants to download new information to the smart card. Once the CA module is removed, your TV will no longer decrypt scrambled digital DVB-T channels.

To access common interface applications, see TV menu,Adjust feature menu settings, Common Interface, p. 22.

Downloaded From TV-Manual.com Manuals

Before operating your connected equipment you have to make aa selection in the Installation, Select your connections menu,

p. 29.

1. Press the MENU/BROWSE key.

2.Select TV menu and press the cursor right.

3.Select Installation.

4. Press the cursor right.

5.Select Connections.

6.Press the cursor right.

7. Select the input to which the peripheral equipment is connected.

8. Press the cursor right again to enter the list of types of peripherals connected to the selected input

9. Select the peripheral equipment with the cursor up/down.

Record with your recorder

Note: to record digital programmes to an analogue recorder, the TV needs to be switched on and tuned to that digital programes.

Record a TV programme

You can record a TV programme using your recorders tuner without affecting your TV.

1.Select the channel number on your recorder.

2.Set your recorder to record.

See the handbook for your recorder.

Note: when recording analogue progammes, switching channel numbers on your TV does not disturb recording !

Downloaded From TV-Manual.com Manuals

Most of the audio and video equipment from our range of products can be operated with the remote control of your TV. Press one of the keys after you pressed one of the mode keys (DVD, STB, VCR, AUX) according to the equipment you want to operate with this remote control.

See Use of the Remote control, p. 5-6.

Normal mode: if no action is being undertaken within 30 seconds, the remote control returns to TV mode.

Expert mode: in Expert mode the remote will stay in the selected mode even when the 30 seconds time-out is elapsed.

To select between Normal and Expert mode

1.Select TV mode with the TV key.

2.Press the OK key simultaneously with the ?? key for four seconds.

>When the B key is On for one second, the Expert mode is selected and the remote control will remain in the mode selected.

3.Select the desired mode (DVD, STB, VCR, AUX)

4.To go back to the TV mode, select TV and repeat steps 1. to 3.

Downloaded From TV-Manual.com Manuals

Annex 1:To set the remote control to work a Philips DVD or DVD/R EN

Your TV remote control gives you the opportunity to control your Philips DVD or DVD/R.

1.Press the DVD mode key for 4 seconds until the LED lights up constantly

2.Enter the code 500 with the digit keys for a Philips DVD player.

Enter the code 542 with the digit keys for a Philips DVD recorder.

>All mode LEDs will blink fast for 3 seconds as a confirmation you entered the correct code.

If you entered a wrong code all mode LEDs will stay on for 2 seconds. Redo Step 2.

>Your remote control is in the DVD or DVD/R mode.

To cancel the selected mode

<Press the DVD mode key for 4 seconds.

> The remote control will return to TV mode.

Downloaded From TV-Manual.com Manuals

Introduction

Philips offers software upgrade capability for your TV using portable memory. After you have completed a software upgrade, your TV will typically perform better.

What improvements are made depends on the upgrade software you are using as well as the software your TV contained before the upgrade.

You can execute the software upgrade procedure yourself. Be aware that the content of this document is addressing technical or software skilled users.

To prepare a portable memory for software upgrade

For the procedure you will require:

-a personal computer with web browsing capability;

-an archive utility that supports the ZIP-format (e.g.WinZip for Windows or Stuffit for Mac OS);

-a preferably empty USB memory stick.

Note: only FAT/DOS-formatted portable memory is supported.

New software can be obtained from your dealer or can be downloaded from the www.philips.com/support website:

1.Go to www.philips.com/support using the web browser on your PC.

2.Follow the procedure to find the information and the software related to your TV.

3.Select the latest software upgrade file and download it to your PC.

4.Decompress the ZIP-file and copy the file ???autorun.upg??? to the root directory of the USB portable memory.

Note: only use software upgrades that can be found on the www.philips.com/support web site.

To verify the version of the TV software

Before you start the software upgrade procedure, it is advised to check what the current TV software is.

1.Select Software Upgrade in the TV menu, Installation, Software upgrade.

2.Press the cursor right.

> The Software Upgrade menu moves to the left panel.

3.Select Current Software Info to observe the version and the description of the current software.

Downloaded From TV-Manual.com Manuals

Software Upgrade Application

Upgrade busy...

Software Id: TL32E-234

Validating Done

Programming

Automatic software upgrade procedure

1.Switch off your TV and remove all memory devices.

2.Insert the USB portable memory that contains the downloaded software upgrade.

3.Switch on your TV with the power key B at the side of the TV.

4.At startup the TV will scan the USB portable memory until it finds the update content.The TV will automatically go to the upgrade mode. After a few seconds it will display the status of the upgrade procedure.

Warning:

-you are not allowed to remove the USB portable memory during the software upgrade procedure;

-in case of a power drop during the upgrade procedure, don???t remove the USB portable memory from the TV. The TV will continue the upgrade as soon as the power comes back;

-if you try to upgrade to a software version lower than the current version, a confirmation will be asked. Downgrading to older software should only be done in case of real necessity;

-if an error occurs during the upgrade you should retry the procedure or contact your dealer;

-the automatic software upgrade procedure will only start if the version on the USB portable memory is different from the one in the TV.

5.When the software upgrade was successful, remove the USB portable memory and restart your TV with the power switch B at the side of the TV.

Your TV will start up with the new software.

Note: once the upgrade is finished use your PC to remove the TV software from your USB portable memory.

Downloaded From TV-Manual.com Manuals

Notes:

-the latest version of this document can be found on the Philips support website (www.philips.com/support).

Use the type number of your TV to find this documentation and other related files.

-Philips can???t be held responsible for any problems that may occur as a result of the content in this document. Errors reported to Philips will be adapted and published on the Philips support website as soon as possible.

Introduction

This document explains how to make a Philips slideshow file with background audio.

Be aware that the content of this document is addressing technical or software skilled users. To start the slideshow open the slideshow file in the Multimedia browser of your TV.

1.Press the MENU/BROWSE key on the remote control after having inserted a USB device and switched on the TV.

2.Go to where you stored the slideshow file (.alb) on your portable memory.

3.Select the slideshow file and press the OK key to start the slide show.

4.To stop a slide show, press the ??? key.

General Rules

-The slideshow will use plain ASCII XML syntax to allow the creation and editing of the slideshow files using simple tools.

-All references to network content must be based on the global address of the content.

-Content on a Portable Memory (PM) doesn't have a global address; as a result content from a PM can never be referenced from a slideshow not stored on the PM itself.

-To maintain portability, a slideshow stored on a PM should ONLY reference content on the same

PM. Referencing global addresses can result in inconsistencies if the PM is used on a non- networked CE device. The latter is however not forbidden, it is only a recommendation.

-It is preferable that URL???s referencing PM content are based on a relative path starting from the directory where the slideshow is stored. This path includes the device or drive name of the PM. An absolute path to content will also be supported.

-relative path: pictures\test1.jpg, tamper.jpg, ..\new\bird.jpg, ???

-absolute path: USB1:\pictures1\foo_bar.jpg, C:\f1.jpg, \organization.jpg, ???

General Format

The format and syntax below will be used to create the slideshow file (simple ascii text) with the extension .alb (.ALB). Examples: slshow1.alb, summer_holiday_2004.ALB, test.alb, ???

The following syntax should be used to create the text file:

<?xml version="1.0" encoding="ISO-885h9-1" ?> <philips-slideshow version="1.0" >

<title>Title of the slideshow</title> <audio>audio_url</audio> <slide-duration>30</slide-duration> <slides>

<slide>slide_1_url</slide> <slide>slide_2_url</slide> <slide>slide_3_url</slide> <slide>slide_4_url</slide> <slide>slide_5_url</slide> <slide>slide_6_url</slide>

...

<slide>slide_N-1_url</slide> <slide>slide_N_url</slide>

</slides> </philips-slideshow>

Downloaded From TV-Manual.com Manuals

Notes:

-the latest version of this document can be found on the Philips support website (www.philips.com/support);

-the software of your TV is upgradeable. If you have problems first check if you have the latest software installed on your TV. The latest software, together with instructions, can be found on the Philips support website. Use the type number of your TV to find this documentation and other related files.

-Philips can???t be held responsible neither for any errors in the content of this document nor for any problems as a result of the content in this document. Errors reported to Philips will be adapted and published on the Philips support website as soon as possible.

Digital Camera Issues

If a USB connection between your digital camera and the TV isn???t working, you can try the solutions below to resolve your problem.

-Make sure your digital camera is switched on and verify if the configuration of your digital camera is correct (see the manual of your digital camera for more information).

-Some digital cameras allow you to switch off the USB interface. Make sure that the USB interface

is switched on before connecting to the TV.

-If you have a digital camera with only internal memory (no removable memory) you can try to copy the content manually to a USB memory device using a personal computer.

-Some digital cameras allow you to switch between PTP (Picture Transfer Protocol) or ???PC Link??? and USB Mass Storage. Make sure that you select USB Mass Storage or ???PC Drive??? on your digital camera.

-If your camera supports different interface settings be sure to try them one by one or contact the reseller of your camera to find out the correct setting.

USB Memory Device Issues

-Devices connected to the USB port of your TV must be ???Mass Storage Class??? compliant. If your device (digital camera. MP3 player, portable harddisk, ???) is not ???Mass Storage Class??? compliant it

will not be detected by the content browser of the TV.

- The following subsets of the Mass Storage Class specification are supported:

The implementation of the TV is based on the ???Universal Serial Bus Mass Storage Class Specification Overview??? (v1.2, June 23, 2003) including all documents referenced by the document. The document can be found on the USB standardisation website (www.usb.org). Full support of the USB Mass Storage Class Bulk-Only Transport (bInterfaceProtocol = 50h). Full support of SubClass Code = 05h; SFF-8070i spec.

Full support of SubClass Code = 06h; SCSI transparent command set.

-For large USB memory devices, when you are in the Content Browser, it may take a long time before you can access your files.

-When using a USB portable harddisk: Due to the high power consumption of the harddisk, it is advised to use the external power supply of the portable harddisk to guarantee proper working under all conditions.

Digital Content Issues

???Only FAT (DOS) formatted (initialized) portable memory is supported. Errors in this formatting can result in unreadable content. If such problems appear try to re-format the card. Be aware that

formatting the card will also delete all the content on it (pictures, music, ???).

???The maximum size of any multimedia file should never exceed 4Gbyte.

???Do not use a dot ???.??? in folder naming.

???If video streams are supporting multiple audio tracks the first audio track will automatically be selected, the other audio tracks can???t be selected.

???External subtitle files (e.g. DivX.srt subtitle files) are not supported.

Downloaded From TV-Manual.com Manuals

EN Annex 5 - Issues referring to connected peripherals with a HDMI connector

The HDMI IN connector allows the following TV and monitor display modes:

-Your TV supports HDCP (High-bandwidth Digital Content Protection).This is a system for protecting DVD content outputted via HDMI from being copied. It provides a secure digital link between a video source (DVD, PC, etc.) and your TV. Content is encrypted at the source peripheral equipment to prevent unauthorised copies from being made.

-Proper working is only guaranteed with HDMI compliant consumer products.

-Digital peripheral equipments from different manufacturers have the possibility of differing output standards which may cause difficulties for the television to properly display.

-In case no signal is detected from your HDMI equipment, switch off the HDMI equipment and then on again.

To get an optimal viewing, it is advised to switch your DVD player, Blu-Ray of HD settop box to the highest possible supported display modes.

Downloaded From TV-Manual.com Manuals

R The packaging of this product is intended to be recycled. Apply to the local authorities for correct disposal.

The batteries supplied do not contain the heavy metals mercury and cadmium. Please check on how to dispose of exhausted batteries according to local regulations.

Disposal of your old product

Your product is designed and manufactured with highly quality material and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/976/EC.

Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste.

The correct disposal of your old product will help prevent potential negative consequences for the environment and human health.

Product information

-Your TV consumes energy in standby mode. Energy consumption contributes to air and water pollution.Very low standby power consumption.

-Specifications: see the product leaflet on www. philips. com/support.

-If you need further assistance, please call the customer support service in your country.

The corresponding telephone numbers and addresses are given in the supplied Worldwide guarantee booklet.

Downloaded From TV-Manual.com Manuals