Content

28

30

31

ENGLISH

Introduction

Philips digital PhotoFrame can be placed either vertically or horizontally to fit the photos on display.You can place it somewhere in a room for a continuous display by connecting it to the mains power supply.

1.Important

ENGLISH

1.1Safety precautions and maintenance

Read and follow these instructions when connecting and using your PhotoFrame:

???To protect your display from possible damage, do not put excessive pressure on the LCD panel.When moving your PhotoFrame,

grasp the frame to lift; do not lift the it by placing your hand or fingers on the LCD panel.

???Unplug the PhotoFrame if you are not going to use it for an extensive period of time.

???Unplug the PhotoFrame if you need to clean it with a slightly damp cloth.The screen may be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.

???Consult a service technician if the PhotoFrame does not operate normally when you have followed the instructions in this manual.

???The casing cover should be opened only by qualified service personnel.

???Keep the PhotoFrame out of direct sunlight and away from stoves or any other heat source.

???Keep the PhotoFrame dry.To avoid electric shock, do not expose it to rain or excessive moisture.

Important

???When positioning the PhotoFrame, make sure the power plug and outlet are easily accessible.

???To avoid the risk of shock or permanent damage to the set, do not expose the PhotoFrame to rain or excessive moisture.

1.2Care of the PhotoFrame

1Do not drop

PhotoFrame is a complicated electronic device and cannot withstand shock from being dropped.

2Do not expose to moisture

PhotoFrame is neither moisture proof nor moisture resistant. Exposing it to moisture or liquid of any kind will very likely damage your PhotoFrame.

3Do not hit or scratch

The LCD panel of PhotoFrame is made of glass and is therefore sensitive to abnormal force and sharp edges.

4Screen cleaning

Use only a dry soft cloth to clean your screen.



2.Your PhotoFrame

2.1What???s in the box

AC

ENGLISH

2.2Control Buttons and Menu Navigation

???Use your PhotoFrame by pressing the control buttons in the back.

???The control buttons and instructions are shown at the bottom of the menu screen.

Use the navigation controller to move between the menus. Move it left and right to cycle through the menu tree.

2.3Connections

2.3.1Memory Card

Photo display (underside)

A.CF Card

B.SD/ MMC /MS / xD Card

Inserting a memory card:

???Insert the memory card into the slot in the frame.

???For xD, SD, MMC, MMC+, or Memory Stick cards slide the card until it locks in place.

???Push the USB drive in the slot.

???After a few seconds, photos on the memory card will display and a slideshow will start.

DO NOT remove the memory card immediately after inserting it in to the PhotoFrame or when PhotoFrame is counting the Photos.Wait until the screen is stable

Removing a memory card:

???To remove the xD, xD, SD, MMC, or Memory Stick card, push the card again to unlock and then pull out the card.

Note:

To be able to delete photos from the memory card it must NOT be locked.To unlock the card follow the manufacturer???s instructions.

???For installation and more details about his application, follow instrustions in user manual on CD.

Note:

The 5.6??? model does not support a connection.

PhotoFrame

PC

For Mac System: (OS X):

???Connect PhotoFrame to the Mac via a USB cable where it will be recognized as a mass storage device.

???Select the photos to be transferred and copy them directly under the root directory of the storage card. (Only JPEG formatted images supported).

???Disconnect the USB cable

Note:

Do not disconnect PhotoFrame when copying

or transferring Photo between PC and

PhotoFrame.

2.4Product highlights

The PhotoFrame is designed to be flexible and convenient to use and it provides the following features:

???High pixel density for sharp and crisp photo display.

???View photos directly from memory cards

??? no PC needed.

???Auto-Tilt function so portrait and landscape photos are displayed in the best possible way.

???Rotating stand for best possible way of viewing photos.

???Clock and alarm.

ENGLISH

3.Getting started

3.1Placing the Product

The PhotoFrame should be placed on a flat surface and close to a power socket. Keep it away from high temperatures and high levels of moisture

3.2Connecting to the mains

Connect the supplied power cable from PhotoFrame to a power outlet.

1

Note:

For safety reasons and best stability Philips recommend to adjust the stand with the angle defined by the two click positions. Using other positions may cause the PhotoFrame to fall and it is the responsibility of the user.

3.3Turning on your PhotoFrame

Press the power button.

3.4Initial Setup

3.4.1Setting the Language

Press the Mode button to toggle to the Main Menu, select the Setting and navigate Down to Language.

1Navigate Up and Down to select your preferred language (select between English, French, Spanish, Italian, German, Russian, Dutch, Danish, Simplified Chinese and Japanese)

2 Press the Play/OK button to confirm your selection.The new setting will be effective immediately.

Press the Mode button to leave this menu and play the slideshow.

3.4.2Access Menus

There are two ways to access the menu.To quick access the menu while you are viewing photos, press the Menu button to see the menu options for photo editing or slideshow settings. To access the menu options starting from the main menu:

1Press the Mode button.

2Navigate Down to highlight the required menu (Clock, Photos and Settings).

3Press Play/OK to access the menu.

To exit from the menus press the Mode button again to return to the slideshow.

SetTime, Date and Alarm

Use this function to set the time and date of the PhotoFrame

1??? Press the Mode button to access the Main Menu.

???Navigate Down to highlight Clock and press Play/OK.

2??? From the Clock screen, press Menu.

???Navigate Down to Time and Date.

???Navigate Right to Time/Time Mode/ Date and press the Play/OK button.

3Time:

???Navigate Up and Down to select the time.

???Navigate Left and Right to move between hours and minutes.

???Press the Play/OK button to confirm.

Time Mode:

Navigate Up and Down to select 12HR or 24HR.

Date:

???Navigate Up and Down to select the date.

???Navigate Left and Right to move between days, months and years.

???Press the Play/OK button to confirm.

Press the Play/OK button to toggle between Clock, Slideshow or Browse mode. Press the Mode button to leave this menu and play the slideshow.

Note:

The time and date must be set before the Alarm Clock can be set.

ENGLISH

4??? From the Clock screen, press Menu.

???Navigate Up to Alarm Clock.

???Navigate Right to Time/Day/Set On/ Off and press the Play/OK button.

5Time:

???Navigate Up and Down to select the time.

???Navigate Left and Right to move between hours and minutes.

???Press the Play/OK button to confirm.

Day:

???Navigate Up and Down to select

Everyday, Weekday, or Weekend.

???Press the Play/OK button to confirm.

Set On/Off :

???Navigate up or down to select Off or On.

???Press the Play/OK button to confirm.

Press the Play/OK button to toggle between Clock, Slideshow or Browse mode.

Press the Mode button to leave this menu and play the slideshow.

3.4.3Choosing Clock Mode

The clock can either be viewed in the Full screen, Slideshow or both:

Full Screen ??? displays the clock in center of the screen and a pre-selected photo will be displayed.

Slideshow - displays the clock in the bottom right of the screen.

Both - displays the clock in both full screen and slideshow modes.

There are two ways to display photo in the clock mode:

1.To quick access the clock when in slideshow, press Play/OK.

2.To access the clock from the Main menu:

1??? Press the Mode button to access the Main Menu.

???Navigate Down to highlight Clock and press Play/OK.

2??? From the Clock screen, press Menu.

???Navigate Down to Time and Date.

???Navigate Right to Time/Time Mode/ Date and press the Play/OK button.

3??? Navigate Up and Down to select Show clock and press Play/OK.

???Navigate Up and Down to select No Clock or Full Screen, Slideshow or Both.

???Press the Play/OK button to confirm selection.

Press the Play/OK button to leave this menu and play the slideshow, browse or clock mode.

ENGLISH

4.Using your PhotoFrame

4.1View Photos

View pre-stored photos

1Press the Mode button to go to the Main Menu.

2In the Main Menu select photos, select the source as the type of memory card installed (SD/MMC, MMC+, Memory Stick, xD Cards. USB drive).

3Press Play/OK, to play the photos in slidehow mode.

4.2Find a Photo

4.2.1Browse Mode

1When displaying photos in the slideshow, move through the photos, navigating Left and Right to find and select a photo.

2Press Play/OK to toggle between the

Slideshow and Browse modes.

4.2.2Slideshow Mode

Slideshow mode is entered once you turn on the PhotoFrame. Navigate Left and Right to move quickly through the photos.

Note 1:

The frequency of the slideshow can be adjusted. To do so please read ???slideshow frequency??? section.

Note 2:

For slideshow creation and management read the section ???Creating and managing slideshow???.

Note 3:

Photos are easily editable from slideshow mode by pressing the Play/OK button.To go directly to thumbnail mode form read the photo menu section.thumbnail mode form read the photo menu section.

4.2.3Browse Mode

To display photos in clock mode.

1In slideshow mode, use the Left and Right to move quickly through the photos.

2Press Play/OK to the access Browse Mode, press again to go to the clock mode.

4.2.4Thumbnail Access and Navigation

A large number of Photos can be viewed quickly using thumbnail mode

1??? Press the Mode button to access the Main Menu.

???Navigate Up to photo and press the Play/ OK button.

2??? Navigate Down to select the photo source to browse.

???Press Play/OK to access the source.

3 ??? Navigate Left, Right, Up and Down

to move between photos and see a larger version of the image.

Press the Play/OK button to leave this menu and press again to start playing the slideshow.

4.3Copy Photos

When connected to a PC the PhotoFrame is treated as a mass storage device. From the computer, JPEG images can be copied to a memory card inserted into the PhotoFrame. Photos can also be copied between a USB drive to another memory device and vice-versa.

4.3.1Copy from a PC/Mac to your PhotoFrame

1Insert a USB drive/memory card into the Photoframe

2Press Mode to go to the Main Menu.

3Select the photo and then go to the photo source.

4Go to thumbnail mode to select a photo.

5Press Menu to access the menu options for photo editing.

6Select Copy to

7Select PhotoFrame

8Press Play/OK

Note:

PhotoFrame has very limited storage space available. It only stores 1-3 photos

ENGLISH

4.4Delete Photos using the PhotoFrame

If you need to free up space on a memory card you can delete photos.

1??? Press the Mode button to access the Main Menu.

???Navigate Up to Photo and press the

Play/OK button.

2??? Navigate Down to select the media to browse and press Play/OK.

???Press the Up, Down, Left or Right keys to find the image you want to delete.

3??? Press the Menu button and navigate Up to Copy to.

???Press Play/OK

???Navigate Up or Down to Yes or No. Press Play/OK.

???Navigate Right to Yes to confirm the deletion and press Play/OK.

Press the Mode button to leave this menu and play the slideshow.

The delete function is disabled when you first use your Photoframe.To enable the delete function:

1Press Mode to go to Main Menu.

2Press Down to Settings.

3Select Delete function.

4Press Play/OK to go to the option list.

5Select Play/OK.

5.Use more of your PhotoFrame

5.1Menu Navigation

The menu is navigated using the navigation controller and the menu buttons.When in a menu follow the onscreen instructions in the bottom right of the screen for details on how to navigate.

???Navigate the controller Left and Right to cycle through the menus.

???Navigate Down and Up to select options.

???Press the Menu button to go to the main menu.

???Press the Play/OK button to make a selection.

???Press the Mode button to exit the current menu and play a slideshow.

5.2Photo Menu

5.2.1Rotate, Zoom and Crop

PhotoFrame can change the orientation of photos and change the framing of photos.

Note:

The crop function only applies to original photos stored on external memory card.

Rotating

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Photo and press the

Play/OK button.

2??? Navigate Down to select the media to browse and press Play/OK.

???Press the Up, Down, Left or Right keys to find the image you want to rotate.

ENGLISH

3??? Press the Menu button and navigate Up to Rotate.

???Press Play/OK or navigate Right.

???Navigate Up or Down to the rotation required. Press Play/ OK.

Press the Mode button to leave this menu and play the slideshow.

Zooming and Cropping

Note 1:

To retain image quality it is recommended that zooming and cropping is carried out before the image is stored in the PhotoFrame.

Note 2:

All photos processed and copied by the PhotoFrame will be resized for optimal display on PhotoFrame and to save storage space.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Photo and press the Play/ OK button.

2??? Navigate Down to select the media to browse and press Play/OK.

???Press the Up, Down, Left or Right keys to find the image you want to rotate.

3??? Press the Menu button and navigate Up to Zoom and Crop.

???Press Play/OK or navigate Right.

???Navigate Up or Down to the zoom in and out as required. Press Play/OK.

???Navigate Up, Down, Left and Right to pan around the image. Press Play/OK to apply.

???Navigate Right to Yes to confirm the crop and return to the thumbnail images.

Press the Mode button to leave this menu and play the slideshow.

5.2.2Photo Effects

This section describes how to apply the Sepia photo effect to your photos.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Photo and press the Play/ OK button.

3??? Press the Menu button and navigate Up to Photo Effects.

???Press Play/OK or navigate Right.

???Navigate Up or Down to the required effect. Press Play/OK to confirm and return to the thumbnail images.

Press the Mode button to leave this menu and play the slideshow.

ENGLISH

2??? Navigate Down to select the media to browse and press Play/OK.

???Press the Up, Down, Left or Right keys to find the image you want to apply an effect to.

Note:

Effects can be removed by selecting ???no effect???.

5.2.3Frames

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Photo and press the Play/ OK button.

6.Settings

Use this section to setup the PhotoFrame slideshow squences, transition effects, frequency of the change of image, collage effects, background color, brightness levels, display language, enable the delete function on your memory card, automatically turn on and off, check the PhotoFrame status , tilt functions, turning off the beep sound and turning on and off the key help screen when first starting the PhotoFrame

6.1Slideshow Sequence

Slideshows can be played in one of two ways randomly or sequentially.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

Settings

2??? Navigate Down to access Slideshow and navigate Right.

???Navigate Up and Down to select either

Sequential or Random.

???Press Play/OK to confirm.

Press the Mode button to leave this menu and play the slideshow.

6.2Transition Effects

The photos can appear on the screen using special transitions.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

19

ENGLISH

2??? Navigate Down to access Slideshow and navigate Right.

???Navigate Up and Down to select

from the list as follows: NoTransition,

Random, Sliding, Snail, Fading, Translation, Corner Slide, or Grid.

???Press Play/OK to confirm.

Press Play Slideshow to leave this menu and play the slideshow.

Note 1:

This function applies to all the slideshows stored on all media.

Note 2:

Random plays different effects out of sequence during the slideshow transition.

6.3Frequency

Use this function to select how long each photo is displayed during the slide show.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

2??? Navigate Down to access Frequency and navigate Right.

???Navigate Up and Down to select 1 Day, 5 seconds, 10 Seconds, 30 Seconds, 1 Minute, 5 Minutes, 30 Minutes, 1 Hour, 4 Hours or 12 Hours.

???Press Play/OK to confirm.

Press the Mode button to leave this menu and play the slideshow.

Note:

This function applies to all the slideshows stored on all media.

To show multiple photos arranged on the screen at the same time select collage.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

Use this function to select the background border color for photos that are smaller than the PhotoFrame display (these photos appear with black borders).

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

ENGLISH

Note:

If you select random the PhotoFrame will randomly use different collage layouts.

Press the Mode button to leave this menu and play the slideshow.

6.6Brightness

Change the brightness settings of the PhotoFrame to achieve the best visibility depending on the light conditions.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

2??? Navigate Down to access Brightness and navigate Right.

???Navigate Up and Down to select the brightness of the screen from 0 ~ 5

???Press Play/OK to confirm.

Press the Mode button to leave this menu and play the slideshow.

6.7Language

Use this section to choose the menu language of the PhotoFrame.

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

2 Navigate Down to go to language.

3??? Navigate Right to enter the Language menu.

???Navigate Up and Down to select your preferred language (select between

English, French, German, Italian, Japanese, Russian, Simplified Chinese, Spanish, Dutch, and Danish).

???Press the Play/OK button to confirm your selection.The new setting will be effective immediately.

Press the Mode button to leave this menu and play the slideshow.

6.8Memory Card

Use this feature to allow the delete function on the inserted memory card

Delete Permission

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

2 Navigate Down to Delete Function.

3??? Navigate Right and select Do Not Allow or Allow.

???Press Play/OK to confirm choice.

Press the Mode button to leave this menu and play the slideshow.

6.9Timer Function (Auto On/Off)

Depending on your lifestyle and schedule, you may want to have the PhotoFrame to automatically turn ON and OFF for you.

Note:

Local time must be set correctly before setting up this feature (see time and date section in the setup menu).

ENGLISH

Setting the ON and OFF times

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

2 Navigate Down to Auto Dim.

3??? Navigate Right to select Time period.

???Navigate Up or Down to select either

Auto Dim Start or Auto Dim End.

???Navigate Right or Press Play/OK.

4??? Navigate Up and Down to adjust the hours.

???Navigate Right to move to minutes.

???Navigate Up and Down to adjust the minutes.

???Press Play/OK to apply the settings and return to the previous screen.

Turning the Automatic start and finish On and Off

1??? Press the Mode button to access the

Main Menu.

???Navigate Up to Settings and press the

Play/OK button.

2 Navigate Down to Auto Dim

3??? Navigate Right to select On/Off Dim.

???Navigate Up or Down to select either

On or Off.

???Press Play/OK to apply the settings.

Press the Mode button to leave this menu and play the slideshow.

Press the Play/OK to go to Slideshow, Browse or Clock mode.

Note 1:

Digital PhotoFrame will automatically turn off its display exactly at the Auto-Dim-Start time; if the time has already passed it will go into Auto- Dim-End status at the next set time.

Note 2:

If you want to turn ON the PhotoFrame during an auto OFF period, just press any key, the PhotoFrame will wake up until the next auto OFF period.

6.10Check the Status of your Photoframe

You may check the status of your PhotoFrame- how many more photos can be stored, which media are currently connected, and the PhotoFrame software version.

1??? Press the Mode button to access the Main Menu.

???Navigate Down to highlight Settings and press Play/OK.

2??? Navigate Down to go to Status.

???The status of the PhotoFrame is shown in the right window.

???If you have a memory card in the PhotoFrame it will give you the status of the card (card type and free memory left).

Firmware: (PhotoFrame software version)

Connected media: (Lists all memory cards connected to PhotoFrame)

Connected media free space: (remaining free memory in MB)

ENGLISH

6.11Rotate Function (AutoTilt)

With this function your photos will automatically be properly positioned no mater whether you have the PhotoFrame positioned horizontally or vertically.

1??? Press the Mode button to access the Main Menu.

???Navigate Down to highlight Settings and press Play/OK.

2??? Navigate Down to go to Auto tilt.

???Navigate Right to go to On or Off.

???Press Play/OK to confirm selection.

Press the Mode button to leave this menu and play the slideshow.

6.12Beep On/Off

Turning the button sounds ON or OFF

1??? Press the Mode button to access the Main Menu.

???Navigate Down to highlight Settings and press Play/OK.

2??? Navigate Down to go to beep.

???Navigate Right to go to On or Off.

???Navigate Down and press Play/OK to confirm the selection.

Press the Mode button to leave this menu and play the slideshow.

6.13Key Help

When the PhotoFrame first starts a description of the control buttons is displayed for 10 seconds or until the press of any of the buttons. If you would like to turn this function off follow the instructions below.

1??? Press the Mode button to access the Main Menu.

???Navigate Down to highlight Settings and press Play/OK.

2??? Navigate Down to go to Key Help.

???Navigate Right to go to On or Off.

???Navigate Down and press Play/OK to confirm the selection.

Press the Mode button to leave this menu and play the slideshow.

ENGLISH

7.Technical data

Model 6FF3FPW

Picture Display

???Effective viewing area: 113.28 x 84.708 mm

???Resolution: 320 x3(RGB) X234

???Viewing angle: CR>&=10 130RL, 110UD

???Lifetime, to 50% brightness: 20000 hr

Note:

The ???LED life time??? is defined as the module brightness decrease to 50% original brightness if the ambient temperature is 25C and IL=20mA.

???Brightness: 200 cd/m2(typical)

???Aspect ratio: 4:3

???Panel resolution: 320 X 234

???Pixel density: 0.118(W)X0.362(H) mm

Storage Media

??? Memory Card Types: SD/MMC/MMC+/xD/MS

Dimensions

???Set dimensions with stand (W x H x D): 167.8

x135.3 x 100.73 mm

???Weight: 0.308 kg

???Temperature range (operation): 0 ??C to 40 ??C

???Temperature range (storage): -20 ??C to 70 ??C

Power

??? Power consumption: 3W

Model 7FF3FPx

Picture Display

???Effective viewing area: 154.08 x 86.58 mm

???Resolution: 480x3(RGB) x 234 pixels

???Viewing angle: 120RL, 100UD (CR>/=10)

???Lifetime, to 50% brightness: 20,000 hr

???Brightness: 200

???Aspect ratio: 16:9

???Panel resolution: 480X234

???Pixel density: 0.107(W) x 0.37(H)

Storage Media

??? Memory Card Types: SD/MMC/MMC+/XD/MS

Dimensions

???Set dimensions with stand (W x H x D): 206.4

x139.3 x 103 mm

???Weight: 0.366 kg

???Temperature range (operation): 0 ??C to 40 ??C

???Temperature range (storage): -20 ??C to 70 ??C

Power

??? Power consumption: 5W

Model 9FF3FPx

Picture Display

???Effective viewing area: 162 x 121.5 mm

???Resolution: 800 x 3(RGB) x 600 pixels

???Viewing angle:

???Lifetime, to 50% brightness: 20,000hr

???Brightness: 250

???Aspect ratio: 4:3

???Panel resolution: 800x600

???Pixel density: 0.0675(W) x 0.2025(H)

Storage Media

??? Memory Card Types: SD/MMC/MMC+/xD/MS

Dimensions

???Set dimensions with stand (W x H x D): 244.6 x 167.4 x 121.1 mm

???Weight: 0.553 kg

???Temperature range (operation): 0 ??C to 40 ??C

???Temperature range (storage): -20 ??C to 70 ??C

Power

???Power consumption: 6.3W

???Photo format supported: JPEG photo (in DCF structure), Up to 16 Megapixels

???Placement supported: Landscape, Portrait, Photo auto orientation

???Buttons and controls: 6 control key buttons. 1 playback key to play in Slideshow mode, in Browse mode or in Clock mode. 1 key

each to go Up, Down, Right, or Left . 1 Hotkey to toggle to Slideshow mode,Thumbnail mode, or Main menu. 1 Menu key to go to edit menu/, setup menu, or to exit.

???Playback mode: Full screen browse, Slideshow, Thumbnail browse

???Album management: Create, Delete, Edit, Rename

???Photo edit: Copy, Delete, Rotate, Zoom and Crop, Move

???Photo effects: Frames, Sepia

???Slideshow setting: Collage, Random, Sequential,Transition effects

???Screen background color: Black,White, Gray

???Clock function: Set time and date, Clock and Alarm,Auto dim on weekday/weekend

???Setup function: Brightness adjustment, Language, Status,Auto on/off, Beep

on/off, Set time and date, Clock display enable/ disable, Factory setting and Photo source

???System status: Firmware version, Power source, Free memory

???Connected media status: Connected media, Free memory

???OSD Languages: English, French, German, Italian, Japanese, Russian, Simplified Chinese, Spanish, Dutch, Danish

???Plug & Play Compatibility:Windows XP and Vista and Mac OS X

???Regulatory Approvals: BSMI, C-Tick, CCC, CE, FCC, GOST, PSB, UL,

???Other convenience: Kensington lock compatible

ENGLISH

8. Frequently asked questions

Is the LCD screen touch-enabled?

The LCD screen is not touch-enabled. Use the buttons on the back to control Digital PhotoFrame.

Can I switch between different slideshows photos by using different memory cards?

Yes.When a memory card is connected to the Digital PhotoFrame, it???ll slideshow photos stored on that specific card.

Will the LCD screen be damaged if I keep showing the same photo for a long time?

No. Digital PhotoFrame can display the same photo continuously for 72 hours without any damage to the LCD screen.

Can I use Digital PhotoFrame to delete photos on memory card?

Yes, it supports operations to delete photos on external devices such as a memory cards.

Can I print photos from Digital

PhotoFrame?

No, it does not support direct photo printing.

How does the Digital PhotoFrame show high-resolution 4:3 digital photos on its 3:2 screen?

To ensure high picture integrity, Digital PhotoFrame shrinks the photos at original aspect ratio and trims excessive portions before displaying these photos.

Can I use Digital PhotoFrame during its Auto-off periods?

Yes. Press any control button to bring the system back to ON status.

Why doesn???t my Digital PhotoFrame show some of my photos?

Digital cameras take photos and store them

in JPEG format according to camera industry standards. Digital PhotoFrame is designed to show photos following the same industry standards. Some images, such as web images,

scanned images, or photos in RAW format from professional cameras, are not stored according to camera industry standards and therefore cannot be correctly displayed on Digital PhotoFrame. Use PC applications to convert such images into standard JPEG format for Digital PhotoFrame.

My Digital PhotoFrame is ON but the system does not respond anymore!

First make sure the system is properly powered. Then use a pin to trigger the Reset button located on the side of the power button on the back to restore the system.

Why doesn???t my Digital PhotoFrame go into Auto-off status after I set it?

First, make sure you set Current Time,Auto-off at, and Auto-on at correctly. Digital PhotoFrame will automatically turn off its display exactly at the Auto-off time. If the time has already passed for the day, it will start entering Auto-off status at the specified time from the next day.

I???m trying to upload pictures from my PC to a memory card, which I???m then inserting into the DPF. However, the DPF doesn???t show the photos.What can I do?

Load all the photos you want to upload to DPD in the root directory of your memory card. Power off your DPD, insert the memory card, and then restart DPF.After a few seconds, all photos in the root directory of the memory card will be automatically added to PhotoFrame. The root directory on memory card will NOT be emptied after this operation. Note that this operation does not apply to photos in sub- directories.

Do Philips PhotoFrame support progressive JPEG?

PhotoFrame supports progressive JPEG formatted picture, but the slideshow display might be very slow.might be very slow.

9.Service and Warranty

OneYear Limited Warranty (for US and Canada only)

Philips warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specifications and warnings, for a period

of one year from the date of purchase.This warranty extends only to the original purchaser of the product, and is not transferable.To exercise your rights under this warranty, you must provide proof of purchase in the form of an original sales receipt that shows the product name and the date of purchase. For customer support or to obtain warranty service, please visit our website www.philips.com/welcome or Contact Philips Customer Care Center at: 1-888-PHILIPS (1-888-744-5477) IN U.S.A., Puerto Rico, or U.S. virgin islands. 1-800-661- 6162 (French speaking), 1-888-PHILIPS (1- 888-744-5477) (English or Spanish speaking) in Canada.THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. Philips liability is limited to repair or, at its sole option, replacement of the product. Incidental, special and consequential damages are disclaimed where permitted by law. This warranty gives you specific legal rights.You may also have other rights that vary from state to state.

Recycling Information for Customers

Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization???s product, service and activities.

From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.At Philips, end-of-life management primarily entails participation in national take-back initiatives and recycling programs whenever possible, preferably in cooperation with competitors.

There is currently a system of recycling up and running in the European countries, such as The Netherlands, Belgium, Norway, Sweden and Denmark.

In U.S.A., Philips Consumer Electronics North America has contributed funds for the Electronic Industries Alliance (EIA) Electronics Recycling Project and state recycling initiatives for end-of-life electronics products from household sources. In addition, the Northeast Recycling Council (NERC) - a multi-state non-profit organization focused on promoting recycling market development - plans to implement a recycling program.

In Asia Pacific,Taiwan, the products can be taken back by Environment Protection Administration (EPA) to follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw

For help and service, please read the section of Service and Warranty or the following team of Environmental specialist can help.

Mr. Job Chiu - Environment manager Philips Electronics Industries (Taiwan) Ltd, Monitor Business Unit

E-mail: job.chiu@philips.com

Tel: +886 (0) 3 454 9839

Mr. Maarten ten Houten - Senior Environmental Consultant

Philips Consumer Electronics

E-mail: marten.ten.houten@philips.com

Tel: +31 (0) 40 27 33402

Ms. Delmer F.Teglas

Philips Electronics North America

E-mail: butch.teglas@philips.com

Tel: +1 865 521 4322

Banned Substance Declaration

This product comply with RoHs and Philips BSD (AR17-G04-5010-010) requirements

ENGLISH

CE Declaration of Conformity

Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following standards

???EN60950:2000 (Safety requirement of Information Technology Equipment)

???EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment)

???EN55024:1998 (Immunity requirement of Information Technology Equipment)

???EN61000-3-2:2000 (Limits for Harmonic Current Emission)

???EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)

following provisions of directives applicable

???73/23/EEC (Low Voltage Directive)

???89/336/EEC (EMC Directive)

???93/68/EEC (Amendment of EMC and Low Voltage Directive)

and is produced by a manufacturing organization on ISO9000 level.

Federal Communications Commission

(FCC) Notice (U.S. Only)

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

???Consult the dealer or an experienced radio/ DPF technician for help.

Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate the equipment.

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS

ALL REQUIREMENTS OF THE CANADIAN

INTERFERENCE-CAUSING EQUIPMENT

REGULATIONS.

FCC Declaration of Conformity

8FF3FP Responsible Party: Philips Consumer

Electronics North America P.O. Box 671539

Marietta, GA 30006-0026

1-888-PHILIPS (744-5477)

Declaration of Conformity for Products Marked with FCC Logo, United States Only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Commission Federale de la Communication (FCC Declaration)

Note:

Cet ??quipement a ??t?? test?? et d??clar?? conforme auxlimites des appareils num??riques de class B,aux termes de l???article 15 Des r??gles de

la FCC. Ces limites sont con??ues de fa??on ?? fourir une protection raisonnable contre les interf??rences nuisibles dans le cadre d???une installation r??sidentielle. CET appareil produit, utilise et peut ??mettre des hyperfr??quences qui, si l???appareil n???est pas install?? et utilis?? selon les consignes donn??es, peuvent causer des interf??rences nuisibles aux communications radio. Cependant, rien ne peut garantir l???absence d???interf??rences dans le cadre d???une installation particuli??re. Si cet appareil est la cause d???interf??rences nuisibles pour la r??ception des signaux de radio ou de t??l??vision, ce qui peut ??tre d??cel?? en fermant l?????quipement, puis en

le remettant en fonction, l???utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes:

???R??orienter ou d??placer l???antenne de r??ception.

???Augmenter la distance entre l?????quipement et le r??cepteur.

???Brancher l?????quipement sur un autre circuit que celui utilis?? par le r??cepteur.

???Demander l???aide du marchand ou d???un technicien chevronn?? en radio/t??l??vision.

Caution:

Toutes modifications n???ayant pas re??u l???approbation des services comp??tents en mati??re de conformit?? est susceptible d???interdire ?? l???utilisateur l???usage du pr??sent ??quipement.

Les raccordements ?? cet appareil doivent ??tre r??alis??s avec des c??bles blind??s ?? protections m??talliques pour les connecteurs RFI/EMI afin de maintenir la conformit?? avec les R??glements et la L??gislation du FCC.

CET APPAREIL NUMERIQUE DE LA CLASSE

B RESPECTE TOUTES LES EXIGENCES DU

REGLEMENT SUR LE MATERIEL BROUILLEUR

DU CANADA.

EN 55022 Compliance (Czech Republic

Only)

ENGLISH

Polish Center forTesting and Certification Notice

???The equipment should draw power from a socket with an attached protection circuit(a three-prong socket).All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.

???The phasing conductor of the room???s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).

???To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible.

???A protection mark ???B??? confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251.

North Europe Information (Nordic

Countries)

VARNING:

F??RS??KRA DIG OM ATT HUVUDBRYTARE

OCH UTTAG ??R L??T??TKOMLIGA, N??R DU

ST??LLER DIN UTRUSTNING P??PLATS. Placering/Ventilation

ADVARSEL:

S??RG VED PLACERINGEN FOR,AT

NETLEDNINGENS STIK OG STIKKONTAKT

ER NEMT TILG??NGELIGE. Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETT?? VERKKOJOHTO

VOIDAAN TARVITTAESSA HELPOSTI

IRROTTAA PISTORASIASTA. Plassering/Ventilasjon

ADVARSEL:

N??R DETTE UTSTYRET PLASSERES, M??

DU PASSE P?? AT KONTAKTENE FOR

ST??MTILF??RSEL ER LETTE ?? N??.

BSMI Notice (Taiwan Only)

End-of-Life Disposal

???Your new product contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.

???Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.

???(For customers in Canada and U.S.A.) Dispose of in accordance to local-state and federal regulations.

For additional information on recycling contact www.eia.org (Consumer Education Initiative)

Waste Electronics and Electrical

Equipment (WEEE)

This product is labelled with this symbol in accordance with European Directive 2002/96/ EG to indicate that it must not be disposed of with your other household waste. Please check your local city office or waste disposal service for the return and recycling of this product.

Waste Electronics and Electrical

Equipment (WEEE)

This product is labelled with this symbol in accordance with European Directive 2002/96/ EG to indicate that it must not be disposed of with your other household waste. Please check your local city office or waste disposal service for the return and recycling of this product.

End of life directives - Recycling

Your new DPF contains several materials that can be recycled for new uses.

Votre nouveau t??l??viseur contient plusieurs mat??riaux qui peuvent ??tre recycl??s pour de nouvelles utilisations.

Comme tous les produits ACL, cette appareille contenant une petit quantit?? de mercure, SVP se d??barrasser en accord avac les lois f??d??ral et gouvernemental.

ENGLISH