HD7826, HD7824, HD7820
Coffee Machine
IMPORTANT
SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including the following:
Read all instructions before using the appliance.
1.Do not touch hot surfaces. Use handles or knobs. Care must be taken to prevent burns which can occur from touching hot parts or spilling hot liquids.
2.To protect against fire, electrical shock and injury to persons, do not immerse cord, plug, or appliance in water or other liquid.
3.Close supervision is necessary when any appliance is used by or near children.
4.Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts and before cleaning appliance.
5.Do not operate this appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner. Return the Coffee Machine to the Philips Norelco Service Location for examination, repair or adjustment.
6.Use this appliance only for its intended purpose as described in this manual. Do not use accessory attachments not recommended by Philips Electronics North America Corporation as they may result in fire, electric shock or injury to persons.
7.Do not use outdoors.
8.Do not let cord hang over edge of table or counter or touch hot surfaces. Operate on a flat, stable surface away from edge of counter to prevent accidental tipping.
9.Do not place Coffee Machine on or near a hot gas or electric burner, or in a microwave or heated oven.
10.This appliance is intended for household use ONLY; it is not for commercial or industrial use.
11.Any service to the Coffee Machine should be performed by the Philips Norelco Service Location.
12.To disconnect Coffee Machine, press power button 3 to ???OFF???, then remove plug from electrical outlet. Remove plug by gripping plug body and pulling it from the outlet. Never yank or twist cord to unplug.
13.Do not use Coffee Machine if lid has a cracked, loose, weakened or damaged lever.
14.This appliance does not work at temperatures below 50??F/10??C.
15.Do not use this appliance at altitudes higher than 6800 ft. / 2200 m above sea level.
16.Flush the Coffee Machine with fresh water before using it for the first time (See ???Preparing the machine for use???).This will cause the boiler to fill with water; which is essential for the machine to work properly.
17.To prevent scalds and/or property damage, always make sure Coffee Machine lid is securely in place and properly locked before you start using the machine and during brew cycle.
Do not force when opening or closing lid.
18.Do not open lid until Coffee Machine has finished brew cycle. Hot steam or hot water trapped under lid cover could burn your fingers.
19.Warning:To reduce the risk of fire or electric shock, do not remove the bottom cover. No user serviceable parts are inside. Return the Coffee Machine to the Philips Norelco Service Location for examination, repair or adjustment.
SAVETHESE
INSTRUCTIONS
SPECIAL INSTRUCTIONS
This Coffee Machine has a short cord to reduce the hazards of becoming entangled in or tripping over a longer cord. An extension cord may be used if the rating is equal to or greater than the rating of the Coffee Machine. Use an extension cord rated 13 amperes or greater. Care must be taken to arrange extension cord so that it does not hang over the edge of counter top or table top, where it can be pulled on by children or tripped over unintentionally. Operating the Coffee Machine and another appliance at the same time from the same electrical circuit could cause an electrical overload, which would blow the fuse or trip the circuit breaker.
SPECIAL POLARIZED PLUG
INSTRUCTIONS
This Philips Coffee Machine has a polarized plug (one blade is wider than the other) as an added safety feature.To reduce the risk of electric shock:
- Plug will fit into polarized outlet only one way.
- If plug does not properly fit into outlet at first, reverse it. - If plug still does not fit, contact a qualified electrician.
DO NOT ATTEMPTTO DEFEATTHIS
SAFETY FEATURE IN ANY WAY.
WARNING:
-To avoid risk of personal injury or damage to property as a result of overflow, be sure that the cup or mug is centered under the coffee outflow unit during the brew cycle.
-Brewed coffee and coffee pods are very hot. Handle with care to avoid scalding.
-If coffee spout overflows or fails to drain into cup/mug during brewing cycle, do not open lid or handle coffee spout or coffee pod holder(s). Unplug Coffee Machine and wait for contents to cool before handling.
-Do not remove any part of Coffee Machine or cup/mug during the brew cycle as scalding could occur.
-Use only fresh, cool water in this appliance. Do not put any other liquids in this appliance except as instructed in the ???Descaling??? section. Do not refill the water reservoir with hot water or coffee.
-DO NOT attempt to move an appliance containing hot liquids or during the brewing process. Allow appliance to cool completely before moving.
-Keep appliance at least 4 inches away from walls or other objects while operating. Do not place any object on top of coffee machine while operating.
PLEASE READ AND SAVETHIS
INSTRUCTION BOOKLET.
General description (Fig. 1)
AWater reservoir
BGrip area
COutflow valve
DSealing ring
EWater distribution disc
F
G
HCover of coffee spout
ICoffee spout
JCoffee collector
KCup tray
LDrip tray
M
NWater level light rings (HD7826, HD7824 only)
OOn/off button with indicator light
P
Introduction
With Douwe Egberts SENSEO\ coffee pods, you can enjoy a perfect cup of coffee at any time of the day. Every cup is freshly brewed to give you that smooth and full taste.
Using more than 250 years of coffee expertise Douwe Egberts has roasted and ground specially selected coffee beans that, when prepared using a special brewing method
To ensure a smooth and full coffee taste, you should keep the following things in mind:
Fresh water
Use fresh water every day. If you have not used the coffee machine for three days, you have to flush it with fresh water before you use it again
(see section ???Flushing??? in chapter ???Cleaning???).
Fresh coffee pods
Use the SENSEO\ coffee pods that have been specially developed by Douwe Egberts for your SENSEO\ coffee machine for a full, round taste. The Douwe Egberts SENSEO\ coffee pods will stay fresh longer if you store them in an airtight storage container.
A clean machine
Clean and descale your Philips SENSEO\ coffee machine regularly (see chapters ???Cleaning??? and ???Descaling???). Remove used coffee pods after brewing. If a used pod has been left in the coffee machine and you have not used the machine for some time, flush the machine before you use it again (see section ???Flushing??? in chapter ???Cleaning???).
Preparing the machine for use
USE THIS SENSEO\ COFFEE MACHINE FOR ITS INTENDED
HOUSEHOLD USE AS DESCRIBED IN THIS MANUAL.
YOU CANNOT BREW COFFEE IF YOU HAVE NOT FLUSHED THE
SENSEO\ COFFEE MACHINE FIRST!
The flushing cycle causes the boiler to be filled with water. After this the coffee machine is ready for use.
Flush the machine in the following way:
1 Remove the water reservoir.
2Fill the water reservoir with cold water up to the MAX indication and put it back onto the machine.
3Release the lid by moving the lever upwards.
4Open the lid.
5Put the
6Close the lid and lock the lever.
Note:Make sure the lever is properly locked by pushing it down until it snaps home with a click.
Note:Never flush the machine with the lid open.The lid must be properly locked.
7 Put the plug into a grounded 120V AC electrical outlet.
8Put a bowl (with a capacity of at least 1.6 qt./ 1.5 litres) under the spout openings to collect the water.
9Press the on/off button 3.
Type HD7826/HD7824 only: after pressing the on/off button, the light rings around the
10 Press the
The boiler fills itself with water from the water reservoir.This may take
some time (approx. 90 to 150 seconds).The machine switches off
automatically when the flushing cycle ends. During the flushing cycle the
machine produces more noise than during a regular brewing cycle.
Never interrupt the flushing cycle halfway. If you do, the boiler will not fill itself properly.
Note: Before you use the machine for the first time, clean the coffee spout, the coffee collector and the pod holders with hot water and some dish soap or in the dishwasher. Clean the water reservoir thoroughly in hot water, if necessary with some dish soap.
Now your Philips SENSEO\ coffee machine is ready for use.
Brewing coffee
1Fill the water reservoir with cold water up to the MAX indication and put it back onto the machine.
Never pour milk, coffee, hot water or carbonated water into the water reservoir.
-q MIN: minimum amount of water required to brew one 4 oz. cup of SENSEO\ coffee.
-qq/w MIN: minimum amount of water required to brew one 8 oz. mug or two 4 oz. cups of SENSEO\ coffee.
-A full reservoir allows you to make up to eight 4 oz cups or four 8 oz. mugs of SENSEO\ coffee.This makes it unnecessary to fill the water reservoir each time you want to make a cup of coffee.
10
2 Press the on/off button 3.
The indicator light blinks slowly while the water is heating up. Heating up takes approx. 75 seconds.
,The coffee machine is ready for use when the indicator light burns
continuously. If the indicator light blinks rapidly, the water reservoir does not contain enough water for brewing one cup of coffee.
, Type HD7826/HD7824 only: the light rings around the
3Release the lid by moving the lever upwards.
4Open the lid.
5 Place the appropriate pod holder in the machine.
Note: Make sure the pod holder is clean and the sieve in the centre is not clogged, e.g. with loose coffee grounds.
,If you want to make one cup of SENSEO\ coffee, use 1 coffee pod in
combination with the
,If you want to make two cups of SENSEO\ coffee, use 2 coffee pods
in combination with the deeper
6 Place the SENSEO\ coffee pod(s) properly in the center of the pod holder, with the flat SENSEO\ side up and the rounded side facing down.
Note: Use SENSEO\ coffee pods from Douwe Egberts specially designed for your SENSEO\ coffee machine for a full and round taste.
Note:Make sure the coffee in the pod(s) is evenly distributed and press the pod(s) lightly into the pod holder.
Note:Never put normal ground coffee or use torn pods in the SENSEO\ machine, as this will cause it to become blocked.
, Place 1 SENSEO\ coffee pod in the
11
,Place 2 SENSEO\ coffee pods in the
7 Close the lid and lock the lever.
Always check if the lid is properly locked.The lever must be pushed down until it snaps home with a click.
Never start brewing with the lid open.The lid must be properly closed.
8Place one cup or two cups under the spout openings.You can adjust the height of the coffee spout by sliding it upwards or downwards.
If you are using cups, make sure they have a capacity of 5 oz. If you are using a mug, make sure the mug has a capacity of 10 oz. Do not use cups that are too large, as they will cause the coffee to get cold more quickly.
9Press the button indicating the number of cups of SENSEO\ coffee you want to brew.
-Press the
-Press the
Types HD7826, HD7824 only: the light rings around the
water reservoir for brewing two cups of coffee, the light ring around the 2- cup button qq/w will not go on and this button cannot be operated.
, The SENSEO\ coffee machine starts brewing.
-The machine automatically supplies the optimal amount of water.
-You can interrupt the brewing process at any time by pressing the on/off button 3. If you switch the machine back on after having interrupted the brewing process, the machine will not complete the interrupted brewing cycle.
Do not remove the water reservoir during a brewing cycle, as this will cause the machine to draw in air.When this happens, the next cup will only be partly filled.
Type HD7820 only: if the cups are only half full when the machine stops brewing, there was not enough water left in the water reservoir to brew
12
two cups.To obtain two full cups, fill the water reservoir and press the
Note: If you only get a small quantity of coffee or no coffee at all out of the machine, you have not flushed the machine properly before first use. As a result, the boiler is not or not completely filled. Flush the machine properly
(see chapter ???Preparing the machine for use???) before you brew another cup of coffee.
10 Remove the coffee pod(s) after use by lifting the pod holder out of the machine and emptying it.
Be careful when doing this, for there may still be some hot water/coffee on the coffee pod(s) or steam may escape.
Tips
,By rinsing the pod holders, the coffee collector and the coffee spout regularly, you will make sure that the coffee always tastes optimally.
,The SENSEO\ coffee will taste best if you stir it before drinking it.
,If you intend to make another cup of SENSEO\ coffee later, just leave the coffee machine switched on.The machine will automatically switch itself off after 1 hour.
Cleaning
Never immerse the SENSEO\ coffee machine in water or any other liquid.
Never clean the machine by flushing it with the lid open.
1 Always turn machine off and unplug before cleaning it. 2 Clean the outside of the machine with a moist cloth. 3 Remove the coffee collector.
4 Take the coffee spout out of the machine by sliding it upwards.
The coffee spout can only be taken out after the coffee collector has been removed.
13
, You can disassemble the coffee spout for more thorough cleaning!
5Clean the coffee spout, the coffee collector and the drip tray in hot water, if necessary with some dish soap, or in the dishwasher.
6Hold the cup tray in your hand while cleaning it with hot water, if
necessary with some dish soap.
The cup tray can also be cleaned in the dishwasher.
To clean the cup tray, always remove it from the machine, as it might prove sharp when handled incorrectly.Always handle it carefully.
7Clean the pod holders in hot water, if necessary with some dish soap, or in the dishwasher.
Check if the sieve in the centre of the pod holder is clogged. If this is the case, unclog the sieve by rinsing the pod holder under a running tap. Use a soft dish brush to clean the sieve, if necessary.
8Clean the water reservoir in hot water, if necessary with some dish soap.
Note: If you are using a soft dish brush, be careful not to damage the valve in the bottom of the water reservoir.
14
9Do not use an object with sharp edges to clean the water inlet on the machine.
10Rinse the parts with fresh water after cleaning and put them back into the machine.
11Clean the water distribution disc with a moist cloth.
Be careful when you do this; make sure that the rubber sealing ring does not get stuck under the edge of the water distribution disc. If it does, the coffee machine will start leaking!
Flushing
If you have not used the coffee machine for three days, you have to flush it
with fresh water before you use it again. Flush the machine in the following way:
1 Fill the water reservoir with cold water up to the MAX indication and put it back into the machine.
2 Put the
3 Close the lid and lock the lever.
4Put a bowl (with a capacity of at least 1.6 qt./1.5 litres) under the coffee spout to collect the water.
15
5Press the on/off button 3 (1) and subsequently press buttons the
time (2).
The machine fills itself with water from the water reservoir.While
this happens, water comes out of the spout.When the flushing cycle is finished, the machine switches itself off. During the flushing cycle, the machine produces more noise than during a regular brewing cycle
.
Never interrupt the flushing cycle halfway. If you do, the boiler will not fill itself properly. Repeat step 5 if the cycle is interrupted.
Descaling
Regular descaling will prolong the life of the coffee machine and will guarantee optimal brewing results for a long time. If the machine is used twice a day on average, it must be descaled once every 3 months.
1Fill the water reservoir up to the MAX indication with white vinegar or with a mixture of descaler and water according to the
instructions on the package of the descaler.Then put the water reservoir back into the coffee machine.
Use a liquid descaler based on citric acid.
2 Press the on/off button 3.
The machine is ready for use when the indicator light burns continuously.
3Place the
We advise you to put a used coffee pod in the pod holder when you descale the machine.This pod will serve as a ???filter??? to prevent the sieve in the pod holder from getting clogged with scale residues.
4Put a bowl with a capacity of at least 1.6 qt./1.5 litres under the spout openings to collect the vinegar or the mixture of descaler and water.
5Press the
Never descale the SENSEO\ coffee machine with the lid open. Make sure the lid is properly locked.
6Repeat steps 1 to 5 with new vinegar or a new mixture of descaler and water.
16
7 Empty the water reservoir to remove the last vinegar or mixture of descaler and water.
8 Rinse the machine at least 3 times by repeating steps 1 to 5, now using fresh water.
, Do not refill the water reservoir with used hot water.
, Discard hot water each time.
9 Discard the used coffee pod and clean the pod holder after descaling to prevent the sieve in the center from getting clogged.
The indicator light continues You have not yet flushed the coffee machine (see chapter ???Preparing the
The SENSEO\ coffee machine does not produce coffee when used for the first time.
You have not yet flushed the coffee machine.When you use the machine for the first time, you have to flush it before you start brewing coffee
(see chapter ???Preparing the machine for use???).
The indicator light continues Make sure that: to blink rapidly.
the water reservoir has been properly placed;
17
Type HD7826/HD7824 only: the
Water leaks from the coffee machine.
The coffee spout cannot be taken out of the machine.
The lid cannot be opened.
The coffee machine produces less coffee than before.
there is enough water in the water reservoir (i.e. above the q MIN level if you want to brew 1 cup);
the ambient temperature is not lower than 50cF / 10cC. If it is, the machine will not function properly.
Make sure that there is enough water in the water reservoir for brewing 2 cups of coffee. If the light ring around the
Make sure that:
the lid is properly closed (the lever must be properly locked);
the water reservoir has not been filled beyond the MAX level;
the sieve in the centre of the pod holder is not clogged. If it is, unclog the sieve by holding the pod holder under a running tap. If necessary, you can use a soft dish brush or a pin to unclog the sieve;
the coffee pod has been put properly in the centre of the pod holder;
the sealing ring has not got stuck under the edge of the water distribution disc..
the water drops on the worktop are not the result of placing or removing the water reservoir or removing used coffee pods.
you do not remove the water reservoir when the coffee machine is heating up.This may cause water that normally ends up in the water reservoir to leak out of the machine.
In all other cases, contact the Philips Norelco Service Location.
The coffee spout can only be taken out after the coffee collector has been removed.
A vacuum may have temporarily formed under the lid.
Switch the machine off. Pull the lever up as far as it will go and wait
24 hours before opening the lid.You may need to use quite some force.
Make sure that the sieve in the centre of the pod holder is not clogged. If it is, unclog the sieve by holding the pod holder under a running tap. If necessary, you can use a soft dish brush or a pin to unclog the sieve.
If problems continue to occur, contact the Philips Norelco Service Location.
Perhaps the sieve in the centre of the pod holder is clogged. If this is the case, unclog the sieve by rinsing the pod holder under a running tap. Use a soft dish brush to clean the sieve, if necessary.
Descale the machine (see chapter ???Descaling???).
The lid cannot be closed properly.
Check if a used coffee pod is sticking to the water distribution disc. If this is the case, remove the used pod.
Check if you used the correct pod holder. Use 2 pods in combination with the deeper
The SENSEO\ coffee is not strong enough.
Make sure that:
you have used the correct number of pods and have pressed the right button. Use 1 pod in combination with the
the coffee pod(s) have been placed properly in the centre of the pod holder, to prevent water from escaping along the edge of the pod(s). When you are using two coffee pods on top of each other, make sure that the flat SENSEO\ sides of both pods are facing up and press the pods lightly into the pod holder;
you have not used the same pod twice by accident; the coffee in the pod is evenly distributed;
The SENSEO\ coffee is too strong.
The coffee is not hot enough.
If you prefer a more robust flavour, SENSEO\ coffee pods with a stronger blend are available.
If you prefer a milder flavour, SENSEO\ coffee pods with a milder blend are available.
Do not use cups that are too large, as they will cause the coffee to get cold more quickly.When using cups, make sure they have a capacity of 5 oz.When using a mug, make sure it has a capacity of 10 oz.
19
FULLTWOYEARS WARRANTY
Philips Electronics North America Corporation warrants each new Philips Product, model HD7826/7824/7820 (except cord, coffee pods and accessories) against defects in materials or workmanship for a period of two years from the date of purchase, and agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product or loss of parts or subjecting the product to any but the specified voltage.
* Use of unauthorized replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY FOR
WARRANTY SERVICE PERFORMED BY A
AND WILL NOT REIMBURSETHE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply ship the product postage prepaid to the Philips Norelco Service Location (information available online at www.philips.com/norelco or at
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America Corporation.This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Domestic Appliances and Personal Care Company
A Division of Philips Electronics North America Corporation 1600 Summer Street, Stamford, CT
Call
This symbol on the product???s nameplate means it is listed by
Underwriters Laboratories, Inc.
PHILIPS and Philips Shield are Registered Trademarks of Koninklijke Philips Electronics N.V. Senseo is a Trademark of Koninklijke Philips Electronics N.V. when used for coffee makers. Senseo is a Trademark of Sara Lee/NE N.V. when used for coffee pods.
Design and quality by Philips and Sara Lee Douwe Egberts.
2006 Philips Electronics North America Corporation.All Rights Reserved.
4222.200.0010.2