Panasonic_Projector

Important

Information

Important Safety Notice

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLP???Based projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.

Model number: PT-DZ6710E/PT-DZ6700E/PT-DW6300E/PT-D6000E/PT-D5000E

Serial number:

Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.

WARNING:

1.Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.

2.To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

3.Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthing- type mains plug. This plug will only fit an earthing-type mains socket. This is a safety feature. If you are unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the earthing plug.

CAUTION: To assure continued compliance, follow the attached installation instructions, which includes using the provided power cord and shielded interface cables when connecting to computer or peripheral device. If you use serial port to connect PC for external control of projector, you must use optional RS-232C serial interface cable with ferrite core. Any unauthorized changes or modifications to this equipment will void the user???s authority to operate.

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Centre

Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, F.R. Germany

ENGLISH - 2

Important Safety Notice

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Information

Important

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Environment care information for users in China

This symbol is only valid in China.

ENGLISH - 3

Important

Information

Important Safety Notice

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark a or the BSI mark ` on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Centre.

If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green - and - Yellow: Earth

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN - AND - YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

ENGLISH - 4

Precautions with regard to safety

Important

Information

WARNINGS

If you notice smoke, strange smells or noise coming from the projector, disconnect the mains plug from the mains socket.

???Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.

???Check that no more smoke is coming out, and then contact an Authorised Service Centre for repairs.

???Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to take the full weight of the projector.

???If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result.

Installation work (such as ceiling suspension) should only be carried out by a qualified technician.

???If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.

???Do not use other than an authorised ceiling mount bracket.

If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, disconnect the mains plug from the mains socket.

???Continued use of the projector in this condition may result in fire or electric shocks.

???Contact an Authorised Service Centre for repairs.

The mains socket shall be installed near the equipment and shall be easily accessible.

???Unplug the mains plug from the mains socket immediately when problem occurred.

Do not overload the mains socket.

???If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may result.

Never attempt to modify or disassemble the projector.

???High voltages can cause fire or electric shocks.

???For any inspection, adjustment and repair work, please contact an Authorised Service Centre.

Clean the mains plug regularly to prevent it from becoming covered in dust.

???If dust builds up on the mains plug, the resulting humidity can damage the insulation, which could result in fire. Pull the mains plug out from the mains socket and wipe it with a dry cloth.

???If not using the projector for an extended period of time, pull the mains plug out from the mains socket.

Do not handle the mains plug with wet hands.

???Failure to observe this may result in electric shocks.

Insert the mains plug securely into the mains socket.

???Do not use other than the provided mains lead.

???If the plug is not inserted correctly, electric shocks or overheating could result.

???Do not use plugs which are damaged or mains sockets which are coming loose from the wall.

Do not place the projector on top of surfaces which are unstable.

???If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

???Failure to observe this may result in fire or electric shocks.

Do not do anything that might damage the mains lead or the mains plug.

???Do not damage the mains lead, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

???If the mains lead is used while damaged, electric shocks, short-circuits or fire may result.

???Ask an Authorised Service Centre to carry out any repairs to the mains lead that might be necessary.

Do not place the projector on soft materials such as carpets or sponge mats.

???Doing so may cause the projector to overheat, which can cause burns, fire or damage to the projector.

Do not place liquid containers on top of the projector.

???If water spills onto the projector or gets inside it, fire or electric shocks could result.

???If any water gets inside the projector, contact an Authorised Service Centre.

Do not insert any foreign objects into the projector.

???Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks.

Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins.

???Failure to observe this may cause the batteries to leak, overheat, explode or catch fire.

???Store the batteries in a plastic bag and keep them away from metallic objects.

ENGLISH - 6

Precautions with regard to safety

Do not touch the leaked liquid from the batteries.

???If you touch the leaked liquid, it may hurt your skin. Immediately wash away the liquid with water and seek medical advice.

???If you get the leaked liquid in your eye, it may cause blindness or damage. Never rub your eye, and immediately wash away the liquid with water and seek medical advice.

During a thunderstorm, do not touch the projector or the cable.

???Electric shocks can result.

Do not use the projector in a bath or shower.

???Fire or electric shocks can result.

Do not place your skin into the light beam while the projector is being used.

???Strong light is emitted from the projector???s lens. If you place directly into this light, it can hurt or damage your skin.

Do not look into the lens while the projector is being used.

???Strong light is emitted from the projector???s lens. If you look directly into this light, it can hurt and damage your eyes.

Do not disassemble the lamp unit.

???If the lamp section breaks, it may cause injury.

Do not place your hands or other objects close to the air outlet port.

???Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least

50 cm (20") of space], otherwise burns or damage could result.

Replacement of the lamp should be carried out by a qualified technician.

???The lamp has high internal pressure. If improperly handled, explosion might result.

???The lamp can easily become damaged if struck against hard objects or dropped, and injury or malfunctions may result.

When replacing the lamp, allow it to cool for at least one hour before handling it.

???The lamp cover gets very hot, and touching it can cause burns.

Before replacing the lamp, be sure to disconnect the mains plug from the mains socket.

???Electric shocks or explosions can result if this is not done.

Do not allow infants or pets to touch the remote control unit.

???Keep the remote control unit out of the reach of infants and pets after using it.

After removing the battery from remote control unit, keep it away from the reach of children.

???The battery can cause death by suffocation if swallowed.

???If the battery is swallowed, seek medical advice immediately.

Insulate the battery using tape or similar before disposal.

???If the battery comes into contact with metallic objects or other batteries, it may catch fire or explode.

When installing to a ceiling, be sure to use the accessory wire (install in a different location to the ceiling mount bracket) and the eye bolts as an extra preventative measure to stop the projector from falling down.

???If the projector is not secure enough, accidents may result.

Do not place sets directly on top of each other.

???If this is not observed, accidents may result.

Do not use the projector while the projection lens cover is still attached to the projection lens.

???If this is not observed, fire may occur.

Information

Important

CAUTIONS

Do not cover the air inlet port or the air outlet port.

???Doing so may cause the projector to overheat, which can cause fire or damage to the projector.

???Do not place the projector in narrow, badly ventilated places such as closets or bookshelves.

???Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam.

???Using the projector under such conditions may result in fire, electric shocks or plastic deterioration. The plastic deterioration may cause the falling down of the projector which is mounted on the ceiling.

ENGLISH - 7

Precautions with regard to safety

Important

Information

Do not set up the projector in a high temperature environment, such as near a heater or in direct sunlight.

???Failure to observe this may result in fire, malfunction or plastic deterioration.

Do not set up the projector outdoors.

???The projector is designed for indoor use only.

When disconnecting the mains lead, hold the plug, not the lead.

???If the mains lead itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

???Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

???Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them into water or fire.

???Failure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result.

When inserting the batteries, make sure the polarities (+ and -) are correct.

???If the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

Use only the specified batteries.

???If incorrect or different kind of batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

Do not mix old and new batteries.

???If the batteries are used mixing old and new, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

Remove the used batteries from the remote control promptly.

???If you leave used batteries in the remote control for an extended period of time, it may cause liquid leaking, abnormal internal temperature rising or explosion.

If not using the projector for an extended period of time, disconnect the mains plug from the mains socket and remove the batteries from the remote control.

???If dust builds up on the mains plug, the resulting humidity may damage the insulation, which could result in fire.

???Keeping or leaving the remote control with batteries inside may cause insulation deterioration, electrical leakage or explosion which could result in fire.

Do not use the old lamp unit.

???The lamp section may break.

Do not put your weight on this projector.

???You could fall or the projector could break, and injury may result.

???Be especially careful not to let young children stand or sit on the projector.

Disconnect the mains plug from the mains socket as a safety precaution before carrying out any cleaning.

???Electric shocks can result if this is not done.

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.

???Failure to observe this may cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces may cause injury.

???If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical advice immediately.

???Ask your dealer about the replacement of the lamp unit and check the inside of the projector.

Ask an Authorised Service Centre to clean inside the projector at least once a year.

???If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation.

???It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorised Service Centre to clean the projector when required. Please discuss with the Authorised Service Centre regarding cleaning costs.

Do not use chemical treated wipes when cleaning.

???Using chemical treated wipes may result in plastic distortion or deterioration.

ENGLISH - 8

We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable units back to your dealer or a recycling company.

Information

Important

Cautions when transporting

Do not subject the projector to excessive vibration or shocks.

???The projector lens need to be handled with care.

???Cover the lens with the lens cover when transporting the projector.

When transporting the projector, hold the body at the bottom securely.

???Do not hold the adjuster legs or the top cover to move the projector, as this may damage the projector.

Be sure to always remove the lens during transport.

???The projection lens is susceptible to vibrations and impacts.

Cautions when installing

Avoid setting up in places which are subject to vibration or shocks.

???The internal parts can be damaged, which may cause malfunctions or accidents.

Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner or lighting equipment.

???The life of the lamp may be shortened or the projector may be turned off. See ???TEMP indicator??? on page 28.

Do not set up the projector near high-voltage power lines or near motors.

???The projector may be subject to electromagnetic interference.

If installing the projector to the ceiling, ask a qualified technician to carry out all installation work.

???You will need to purchase the separate installation kit (Model No. ET-PKD56H, ET-PKD55S). Furthermore, all installation work is should only be carried out by a qualified technician.

If using this projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) sea level, set the HIGH ALTITUDE MODE to ON.

???Failure to observe this may result in malfunctions or the life of the lamp or the other components may be shortened.

Be sure to install the projection lens cover after installing the projection lens.

???If this not done, dust will collect inside the projector and problems with the projector will result.

Cautions on use

In order to get the best picture quality

???Draw curtains or blinds over any windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.

???In rare cases, wafture can occur on the screen affected by the warm air from the exhaust port depending on the environment. Make sure that there is no equipment in front of the set which will recirculate the exhaust air from the set or other nearby equipment.

Do not touch the surfaces of the lens or the front glass with your bare hands.

???If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, close the front panel cover.

ENGLISH - 9

Precautions with regard to safety

Important

Information

The projector has a high pressure mercury lamp and that is characterised as follows.

???The brightness of the lamp depends on the duration of use.

???The lamp may explode or shorten the lamp life by shocks or chipping damage.

???The lamp may explode only occasionally after using the projector.

???The lamp may explode if using the projector after the instructed lamp replacement timing.

???When the lamp exploded, it emits internal smoke-like gas.

???The lamp life is depends on individual lamp characteristics, usage condition and the installation environment. Especially the consecutive use of the projector for more than 22 hours, or the frequent switching on or off may greatly affect on the lamp life.

???Provide a lamp for replacement in advance.

Optical components

???If you use the projector consecutively 22 hours every day, the optical components may need to be replaced in less than 1 year.

Do not use projectors with the adjustable feet or projection lens cover removed.

???If this is not observed, the sets may not operate correctly or accidents may result.

DLP chips

???The DLP chips are made using extremely high- precision technology. Note that in rare cases, pixels may be missing or always lit, but this is not a malfunction.

Others

Disposal

???When disposing of the product, contact your nearest municipality or dealer to confirm the correct procedure for disposal.

Connection to external device

???When connecting the projector to a computer or external device, use the power cord supplied with the corresponding device and a commercially available shielded interface cable.

Security

Take the safety measures for use of the projector that should cover the following envisioned incidents.

???The leakage of your personal registered information.

???Dishonest operation by an untrusted third party.

???Locking out or prevent anyone else from using the projector by an untrusted third party.

Security instruction

???The connecting network must be secured by firewall or others.

???Change your password regularly.

???Do not use password too simple to guess.

???The Authorised Service Centre will never ask you for the password.

???Do not share your password with anyone else.

???Password the projector and restrict access to authorized users only.

ENGLISH - 10

??? Side views

S-VIDEO IN

Connect an S-VIDEO signals. (Mini DIN 4 pin)

VIDEO IN

Connect a video signals. (BNC)

LAN

Connect a LAN cable for network connection.

(RJ-45)

About Your Projector

RGB 1 IN

Connect an RGB or YPBPR signals. (3, 4 or 5 wire BNC)

RGB 2 IN

Connect an RGB or YPBPR signals. (D-SUB 15 pin female)

Air intake port

POWER button

Switch the projector on/off. (page 19)

Air intake port

AC IN terminal

Connect the main lead to supply electronic power to the projector. (page 19)

Security lock

Attach the commercial shackle lock, manufactured by Kensington, to protect your projector. Compatible with the Kensington MicroSaver Security System.

Auto Cleaning Filter (ACF) compartment (page 32)

NOTE:

???Switch on the POWER button of the projector body that is located near the terminals before using the control buttons.

???Do not touch the LAN terminal with your bare hands or body, as body parts may have charged static electricity. Failure to do so may cause malfunctions. Do not touch the metallic parts of LAN terminal and cable.

???Please connect the LAN to indoor devices only.

ENGLISH - 13

About Your Projector

Remote control

Preparation

POWER ON and POWER STANDBY buttons

POWER ON: Starts

the projection while in the standby mode. POWER STANDBY: Returns to the standby mode. (page 19)

INPUT SELECT buttons

These buttons select the RGB1,

RGB2, DVI-D,

VIDEO, S-VIDEO and SDI terminals. (page 22)

MENU buttons

Displays and clears the main menu, and returns to the previous menu when the menu is displayed. (page 27)

ON SCREEN button

Displays and clears the on screen indications. (page 22)

TEST PATTERN button

Displays the test pattern.

(page 22) Numeric (0 - 9) buttons

Enter ID number of the remote control and adjustment values of menu items. (page 15)

STATUS button

Displays projector information. (page 23)

Navigation and ENTER buttons Navigate through the

menu items with F G I H, and activate them with the ENTER button. (page 27)

Remote control indicator Flashes by pressing any buttons. (page 21)

AUTO SETUP

Pressing this button while projecting an image automatically corrects the

picture positioning on the screen. While the auto setup feature is active, a message ???PROGRESS??? appears on the screen. (page 21)

SHUTTER button

Pressing this button toggles

the projector???s internal mechanical shutter to black out

the projector. (page 22)

ASPECT button

Switches the image aspect ratio. (page 22)

LENS buttons

These buttons are used

together with F G I H to adjust focus, zoom and shift by the projection lens. (page 19)

FUNCTION button

Assign the frequently use functions from options for shortcut. (page 23)

DEFAULT button

Restores the default factory

setting. (page 23)

ID buttons

ALL: Makes the remote control available to

control any ID

projectors.

SET: Specifies the ID of the remote control. (page 15)

Battery compartment

1.Press the tab and lift up the cover.

2.Insert the batteries according to the polarity diagram indicated inside.

NOTE:

???Switch on the POWER button of the projector body that is located near the terminals before using the remote control.

???Do not drop the remote control.

???Avoid contact with liquids or moisture.

???Use manganese batteries with the remote control.

???Do not attempt to modify or disassemble the remote control. Contact an Authorised Service Centre for repairs.

???Do not keep pressing the remote control buttons as this may shorten battery life.

???See ???Remote control operation??? on page 21.

ENGLISH - 14

Preparation

NOTE:

???Do not press the ID SET button accidentally or carelessly because the ID number on the remote control can be set even when no projector is around.

???If you do not enter the 2 digits ID number within 5 seconds after the ID SET button has been pressed, the ID will remain at the number that was set before the ID SET button was pressed.

???Your specified ID will be erased if the batteries of the remote control are left exhausted. When the batteries are replaced, set the same ID number again.

Connect to another projector

M3 stereo mini jack (commercial)

Connect to the remote control wired terminal

NOTE:

???Use 2 core shielded cable of length of 15 m or less. If the length of the cable exceeds 15 m (49'2"), the shielding of the cable may not be sufficient and the remote control may not work.

ENGLISH - 15

Setting up

Projection method

You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,

???Setting on a desk/floor and projecting from front

???Mounting on the ceiling and projecting from front

Started Getting

NOTE:

???A translucent screen is required for rear projection.

???See more detailed setting up instructions, INSTALLATION and COOLING CONDITION in PROJECTOR SETUP menu on the functional instructions in the CD that is provided with the projector.

???Do not place or use a projector on top of another projector.

???Cautions when setting the projectors

When placing the projector in confined space, a ventilation or air conditioning system must be equipped, and keep enough ventilation space on the rear and both sides of the projector.

over 10 cm (4")

NOTE:

???Do not stack the projectors without using frame or shelf.

???Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.

???Avoid heating or cooling air of the air conditioning systems directly blow on to the projector ventilation openings.

???You can tilt the projector within ?? 15 degrees horizontally.

ENGLISH - 16

Setting up

Removing and attaching the projection lens

???Removing the projection lens from the projector

1.Switch off the POWER button on the projector.

2.Rotate the lens cover counterclockwise and remove.

Lens cover

???Attaching the projection lens to the projector

1.Switch off the POWER button on the projector.

???When the lens cover is attached, rotate counterclockwise and remove.

2.Align the guide of the projection lens with the guide groove in the projector, and then insert the lens.

Getting Started

NOTE:

???Do not touch the lens signal receiver. Dust or dirt may cause defective contact.

???Do not touch the surface of the projection lens with your bare hands.

???Store the replaced lens where it will be free from vibration and impact.

4.To attach the slot, align the slot of the lens cover (see *1) with the arrow tip located on the body of the projector (see *2). Rotate clockwise until it reaches the arrow???s end mark (see *3) to attach.

Lens cover

NOTE:

???Make sure the projection lens is attached securely by rotating the projection lens counterclockwise.

ENGLISH - 17

Setting up

Mains lead

Started Getting

2.Align the side of the ???power cord secure lock??? with the side guide rail of the AC IN terminal of the projector and slide it in.

Rail guide

3.Place the latch to the latch catcher and press until it clicks.

Latch

4. Connect the mains lead to a mains socket.

NOTE:

Latch

3.Slide the ???power cord secure lock??? up along the side guide rail and remove.

Rail guide

4.Hold the plug and unplug the mains lead from the AC IN terminal on the back of the projector.

???Power indicator lights in orange if the internal cooling fan is still operating by internal power supply.

???Do not use other than the provided mains lead.

???Ensure all the input devices are connected and turned off before connecting the mains lead.

???Do not force the connector as this may damage the projector and/or the mains lead.

???Dirt or dust build-up around plugs may cause fire or electrical hazards.

???Switch off the power to the projector when not in use.

???If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start the projection.

ENGLISH - 18

Projecting

Projecting a image

??? Switching on the projector

When using an optional lens, install a projection lens before switch on the projector.

1.Connect the supplied mains lead (220 - 240 V AC, 50 Hz/60 Hz) to the AC IN terminal.

2.Remove the projection lens cover from the lens.

3.Switch the POWER switch on that is on the side of the projector.

???The power indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode.

4.Press the POWER ON button

???The power indicator lamp illuminates in green and soon the image is projected on the screen.

POWER ON button

??? Making adjustment and selection

It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus.

1.Roughly adjust the focus of the lens.

2.Select and set the projection scheme of

INSTALLATION and COOLING CONDITION settings in PROJECTOR SETUP menu.

3.Select the input signal by pressing the INPUT SELECT buttons.

4.Adjust the vertical tilt of the projector with the front leg adjusters.

5.Adjust the shift position of the projection.

???If the input signal is RGB signal, additionally press the AUTO SETUP button to adjust the position of the image.

6.Zoom the lens so the image fills the screen.

7.Readjust the focus.

8.Readjust the zoom so that the image size fits in the screen.

???Adjusting focus, zoom and shift

INPUT SELECT buttons

Basic Operation

NOTE:

???If the projector is powered up at about 0 ??C (32 ??F), a warm- up period of approximately 5 minutes may be necessary to start projection. The temperature monitor (TEMP) lamp lights up during the warm-up period. When the warm-up is completed, the temperature monitor (TEMP) lamp turns off and the image is projected on the screen.

???If the temperature of the operating environment is low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off automatically. If this happens, increase the temperature around the projector so that it is 0 ??C (32 ??F) or higher, and then turn on the POWER switch and press the POWER ON button again.

LENS button

CAUTION:

???Be careful not to catch your fingers between the lens and shroud when shifting the lens.

NOTE:

???The setup screen will be displayed with the optional fixed lens though, it will not be functioning.

???Pressing F G I or H for 3 seconds or more, performance the adjustment faster.

ENGLISH - 19

Projecting

??? Switching off the projector ??? Lens home position

Operation Basic

1.Press the POWER STANDBY button.

??? The confirmation screen will be displayed.

POWER STANDBY button

2.Select OK and press the ENTER button, or press the

POWER STANDBY button again.

???The projection of the image stops, and the power indicator of the projector lights up orange. The cooling fan keeps running.

3.When the power indicator of the projector turns to red, switch the POWER switch to OFF.

???When the power indicator of the projector turns to red, the cooling fan stops.

???While the cooling fan is still running, never turn off the POWER switch, nor unplug the mains lead from the mains socket.

NOTE:

???In the cooling state after the power is turned off, the lamp will not light up even if the power is turned on. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently. Failure to observe this may shorten the lamp life.

???Direct power off function

The power supplied internally causes the cooling fan to continue operating and cool off in the event that the power has failed or even after the mains lead is accidentally disconnected immediately after the power has been turned off.

NOTE:

???When the lamp has been cooled by the direct power off function, it sometimes takes longer than usual for the lamp to light up again.

???While the cooling fan is operating, do not place the projector inside a box or bag.

1.Press and hold the LENS button of the control button on the projector or SHIFT button of the remote control for 3 seconds or more.

???The HOME POSITION setup screen will be displayed for 5 seconds.

2.Press the ENTER button before the setup screen disappeared.

???While the lens returning to the home position, a message ???PROGRESS??? appears on the screen.

NOTE:

???The home position for the projection lens is the lens position when the lens is being replaced or when the projector is being stored away, and it is not the optical centre of the screen.

???Adjustment range after lens

position (optical shift)

Do not move the lens beyond the bounds of the shift range as this may cause a change in the focus. This limitation is to protect the parts of the projector. Using the standard projection position as the reference, the optical axis shift function makes it possible to adjust the projection position in the ranges shown in the figures below.

ENGLISH - 20

Remote control operation

Operating range

You can operate the projector with the remote control within the remote range 30 m (98'5"), approximately ?? 30?? horizontally and ?? 15?? vertically.

??? Facing to the projector

Ensure the remote control emitter is facing to the remote control signal receptor on front/back of the projector and press the required buttons to operate.

??? Facing to the screen

Ensure the remote control emitter is facing to the screen and press the required buttons to operate the projector. The signal will be reflected off the screen. The operating range may differ due to the screen material. This function may not be effective with a translucent screen.

NOTE:

???Do not let strong light shine onto the signal receptor. The remote control may malfunction under strong light such as fluorescent.

???If there are any obstacles between the remote control and the remote control signal receptor, the remote control may not operate correctly.

Setting up the image position automatically

The automatic setup function can be used to automatically adjust the resolution, clock phase and picture position when analogue RGB signals consisting of bitmap images such as computer signals are being input, or to automatically adjust the picture position when DVI-D signals are being input.

1.Input an analogue RGB image signal.

2.Press the AUTO SETUP button.

3.Displays a message ???PROGRESS???.

4.Displays a message ???COMPLETE??? when ended.

??? When the performance is not completed and ended, displays ???INCOMPLETE???.

NOTE:

???The automatic setup function does not work with video format signals such as signals output from a DVD player.

???It is recommended to supply images with a bright white frame at the outermost periphery containing characters etc. that are clear in white and black contrast when the system is in automatic adjustment mode.

???Avoid supplying images that involve halftones or gradation such as photographs and computer graphics.

???The clock phase adjustment may have been shifted even when the adjustment ended normally. In this case, manually adjust CLOCK PHASE in POSITION menu.

???If an image with blurred edges or a dark image is input, ???INCOMPLETE??? may appear or adjustment may not be performed properly even if ???COMPLETE??? appears. In this case, manually adjust INPUT RESOLUTION in ADVANCED MENU, CLOCK PHASE and SHIFT in POSITION menu.

???For specific signals and landscape signals such as 16:9, see AUTO SETUP in DISPLAY OPTION menu of the functional instructions that is in the provided CD-ROM.

???Automatic adjustment may not be available depending on the machine type of the computer.

???Automatic adjustment may not be available for synchronisation signal of C-SYNC and G-SYNC.

???Image may be distorted for several seconds during automatic adjustment. This is not a malfunction.

???For every supplied signal, adjustment is required.

???Automatic adjustment can be cancelled by pressing the MENU button during the course of automatic adjustment.

???Even for an RGB signal for which automatic setup is possible, if automatic setup is performed while moving images are being input, ???INCOMPLETE??? may appear, or adjustment may not be performed properly even if ???COMPLETE??? appears.

Basic Operation

ENGLISH - 21

Remote control operation

Switching the input signal

You can use the remote control to switch the signals that are being input and projected.

*1. SDI is only for PT-DZ6710E.

Operation Basic

Stopping the projection

If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is available that allows the user to hide images temporarily.

???Press the SHUTTER button to block the projected light by the internal shutter, and press again to resume.

Clearing the on-screen menu

Press the ON SCREEN button to clear the on-screen menus to avoid disrupting the program.

???Press the ON SCREEN button again to displays

Changing the picture aspect ratio

You can toggle through an appropriate set of aspect ratios for a given input signal. The setting will change each time the ASPECT button is pressed.

??? Appearance sample

S-VIDEO signal

??? VID AUTO H S1 AUTO H VID AUTO(PRI.) H THROUGH H 16:9 H 4:3 H H-FIT H V-FIT H HV-FIT H VID AUTO

NOTE:

???The appearance of setting options vary according to input signals. See ASPECT in POSITION menu of the functional instructions that is in the provided CD-ROM.

Displaying the internal test pattern

The projector has 7 types of internal test patterns to check the condition of the set.

1.Display an input signal image.

2.Press the TEST PATTERN button.

3.Press I H to select the required test pattern.

NOTE:

??? See TEST PATTERN menu of the functional instructions that is in the provided CD-ROM.

ENGLISH - 22

Remote control operation

Using an assigned function

You can assign a selected function to the FUNCTION button. Following functions are assignable.

NOTE:

???See FUNCTION in PROJECTOR SETUP menu and each corresponding menu items of the functional instructions that is in the provided CD-ROM.

Displaying the status of the projector

Pressing this button displays several pages of projector status information.

NOTE:

???See STATUS in PROJECTOR SETUP menu and ???Accessing with the web browser??? in Technical Information of the functional instructions that is in the provided CD-ROM.

Resetting to the factory default

If an adjustment item is selected and press the DEFAULT button, the adjustment value will return to the factory default setting.

Basic Operation

ENGLISH - 23

Menu Navigation

Main menu and Sub-menu

The menu options are structured and categorised. You can navigate through the menu with F G I H buttons. See ???Navigating through the menu??? on page 27.

???Some default settings vary by the selected input signal.

???Sub-menu items vary according to the selected input signal.

???Some settings are adjustable without any signals.

???See the functional indications in the CD-ROM that is provided with the projector.

PICTURE

PICTURE MODE

(Default: 0)

BRIGHTNESS

(Default: 0)

COLOR

(Default: 0)

TINT

(Default: 0)

COLOR TEMPERATURE

CLOCK PHASE

(Default: 16)

GEOMETRY

(PT-DZ6710E only)

GEOMETRY:KEYSTONE

VERTICAL KEYSTONE

VERTICAL SUB KEYSTONE

HORIZONTAL KEYSTONE

HORIZONTAL SUB KEYSTONE

LINEARITY

GEOMETRY:CURVED

LENS THROW RATIO

VERTICAL KEYSTONE

HORIZONTAL KEYSTONE

VERTICAL ARC

HORIZONTAL ARC

VERTICAL BALANCE

HORIZONTAL BALANCE

KEYSTONE

(PT-DZ6700E/PT-DW6300E/PT-D6000E only)

VERTICAL KEYSTONE

VERTICAL SUB KEYSTONE

LINEARITY

Operation Basic

ADVANCED MENU

DIGITAL CINEMA REALITY

BLANKING

INPUT RESOLUTION

CLAMP POSITION

EDGE BLENDING *

GAMMA

2.21.8 2

BRIGHT ADJUST

RASTER POSITION

VERTICAL HORIZONTAL

POSITION

SHIFT

ASPECT

DISPLAY LANGUAGE

ENGLISH - 24

DVI-D IN

DVI EDID

EDID3 EDID1 EDID2(PC)

DVI SIGNAL LEVEL

0-255:PC16-235

SDI IN

(PT-DZ6710E only)

ON-SCREEN DISPLAY

OSD POSITION

OSD DESIGN

OSD MEMORY

NORMALECO

RS-232C

(IN) BAUDRATE (IN) PARITY

(OUT) BAUDRATE

(OUT) PARITY

RESPONSE(ID ALL)

GROUP

RESPONSE(ID GROUP)

REMOTE2 MODE

DEFAULTUSER

STATUS

FILTER COUNTER RESET

NO SIGNAL SHUT-OFF

DISABLE

10 MIN. 20 MIN. 30 MIN. 40 MIN. 50 MIN. 60 MIN. 70 MIN. 80 MIN. 90 MIN.

FUNCTION BUTTON

DISABLE

SUB MEMORY LIST

SYSTEM SELECTOR

SYSTEM DAYLIGHT VIEW

FREEZE

SIDE BY SIDE

DAY AND TIME

SAVE ALL USER DATA

LOAD ALL USER DATA

INITIALIZE

SERVICE PASSWORD

Basic Operation

ENGLISH - 25

Menu Navigation

SECURITY PASSWORD

SECURITY PASSWORD CHANGE

DISPLAY SETTING

TEXT CHANGE

MENU LOCK

MENU LOCK PASSWORD

CONTROL DEVICE SETUP

CONTROL PANEL

ENABLEDISABLE

REMOTE CONTROLLER

ENABLEDISABLE

NETWORK SETUP

NETWORK CONTROL

WEB CONTROL

PJLink CONTROL

COMMAND CONTROL

COMMAND PORT

STORE

NETWORK STATUS

Settings

ENGLISH - 26

Menu Navigation

Navigating through the menu

??? Displaying the Main menu

Press the MENU button to display the main menu.

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

DISPLAY OPTION

PROJECTOR SETUP

TEST PATTERN

SIGNAL LIST

SECURITY

NETWORK

MENU SELECT

ENTER SUB MENU

???Adjusting with the bar scale items

The triangle mark under the bar indicates factory default setting and the square indicates the current setting.

Current setting

??? Returning to the previous menu

Press the MENU button to return to the previous menu. Press repeatedly to escape from the menu mode and return to the projection.

???Operating procedure

1.Press F G to scroll to the required main menu item and press the ENTER button to select.

???The selected item is highlighted in orange and the sub- menu is displayed.

???See ???Main menu and Sub-menu??? on page 24.

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

DISPLAY OPTION

PROJECTOR SETUP

TEST PATTERN

SIGNAL LIST

SECURITY

NETWORK

MENU SELECT

ENTER SUB MENU

2.Press F G to scroll to the required sub-menu item and press I H or the ENTER button to adjust.

???The selected item is called up and the other menu items disappear from the screen. Called up item will be disappear after 5 seconds and return to the menu mode.

???If there is a lower level, the next level will be displayed.

POSITION

Basic Operation

MENU SELECT

ENTER CHANGE

3.Press I H to adjust or set the selected item.

???For items using a bar scale, the current settings are displayed on the left of the bar scale.

???You can cycle through the options of an item by pressing I H.

ADJUST

4. Press the MENU button to return to the previous menu.

ENGLISH - 27

Monitor Lamp indicators

Managing the indicated problems

Indicators

Power indicator

Lamp1 (LAMP1) indicator Lamp2 (LAMP2) indicator Temperature (TEMP) indicator Filter (FILTER) indicator

ON(GREEN)

If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as follow.

1.Confirm the status of all indicators and projector, and switch off the projector in proper way.

2.Find out the cause of the problem by status of each indicator.

3.Follow the instruction for each indication below and solve the problem.

4.Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.

NOTE:

???If no problem is found or the problem remains, do not turn on the projector. Instead contact your nearest dealer.

???LAMP1/LAMP2 indicator

ENGLISH - 28

Replacement

Replacing the Lamp unit

???Before replacing the Lamp unit

???Turn off the POWER switch of the projector in proper way and disconnect the mains plug from the mains socket.

???Wait for more than 1 hour and make sure the lamp unit and the surroundings are cooled enough.

???Prepare a Phillips-head screwdriver.

???Contact the dealer to purchase a replacement lamp unit (ET-LAD60:1 bulb unit, ET-LAD60W: 2 bulb units).

???When the projector is mounted on the ceiling, do not work directly under the projector or put your face closer to the projector.

CAUTION:

??? The lamp may explode by shocks or chipping damage.

NOTE:

???Prior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.

???Do not attempt replacement with an unauthorised lamp unit.

???Both lamps must be set in a lamp unit. If only one lamp is set, the power will not work.

???When to replace the lamp unit

The lamp unit is consumable and the brightness decreases by duration of usage. The LAMP1/LAMP2

indicators will inform you of the replacement timing at 1 800*2 hours, and at 2 000*1 hours, the projector will be turned off. Those figures are rough guidance and might be shortened by the usage conditions, characteristics of the lamp unit, environmental conditions, and so on. You can check the duration of usage time using LAMP1/

LAMP2 of STATUS in the PROJECTOR SETUP menu.

Indication

REPLACE LAMP

LAMP

Maintenance

CAUTION:

???If you keep using the lamp unit after 2 000*1 hours, it cause the damage of the projector. Automatically the projector will be powered off after 10 minutes.

NOTE:

???The guide times, 1 800*2 and 2 000*1 hours, are rough estimates based on certain conditions and are not a guaranteed time.

???For more information about the lamp unit, see the instructions which is provided with the lamp unit.

*1. 3 000 hours for PT-D5000E.

*2. 2 800 hours for PT-D5000E.

ENGLISH - 30

Replacement

??? Replacement procedure

???Removing and replacing the lamp unit

1.Use a Phillips-head screwdriver to loosen the ???lamp unit cover fixing screw??? (1 screw) on the back of the projector until the screws turn freely, and remove the lamp unit cover.

???Slide the lamp unit cover to the control buttons and pull to remove.

4.Hold the handle of the new lamp unit and replace it in correct direction.

5.Press in the lamp unit until it clicks and make sure the unit is installed securely.

6.Tighten the ???lamp unit fixing screws??? (3 screws) securely with a Phillips-head screwdriver.

Lamp unit cover fixing screw

Lamp unit cover

2.Use a Phillips-head screwdriver to remove the ???lamp unit fixing screws??? (3 screws).

3.Hold the handles of the lamp unit and pull the used lamp unit gently from the projector.

Fan electric power connector

7.Attach the lamp unit cover and tighten the ???lamp unit cover fixing screw??? (1 screw) securely with a Phillips-head screwdriver.

???Slide the lamp unit cover to the hinge side along the guide and push in to attach securely.

???Make sure the fan electric power connector of the lamp unit cover is inserted securely to the projector???s connector.

HandleLamp unit fixing screws

ENGLISH - 31

Replacement

Replacing the Auto Cleaning Filter (ACF)

???Before replacing the ACF

???Wait until the cooling fan stops and turn off the POWER switch of the projector in proper way.

???Disconnect the mains lead from the mains socket.

???Contact an Authorised Service Centre to purchase a replacement ACF (ET-ACF100).

???The ACF unit to be replaced should be an unused product.

???When to replace the ACF

The ACF unit is consumable product and effects on ventilation. The FILTER indicator will inform you of the replacement timing. You can check the remaining amount of the ACF unit in REMAINING FILTER of STATUS in PROJECTOR SETUP menu.

ACF cover fixing screw

ACF cover

2.Slide out the ACF unit from the projector slowly.

???When you replace the ACF unit, clean the compartment and/or the air exhaust port if you need to.

3.Insert the new ACF unit into the compartment in correct direction and slightly push until it clicks.

NOTE:

???If the ACF and/or ACF cover are attached incorrectly, the projector may not be turned on.

???The replacement timing of the ACF depends on environment of usage.

???Resetting the REMAINING

FILTER

1.Turn on the projector and display the FILTER COUNTER RESET in PROJECTOR SETUP menu.

2.Press the ENTER button.

??? The confirmation screen will be displayed.

3.Select OK by pressing I, then press the ENTER button.

4.Display the STATUS in PROJECTOR SETUP menu and confirm the REMAINING FILTER.

NOTE:

???See FILTER COUNTER RESET and STATUS in

PROJECTOR SETUP menu of the functional instructions that is in the provided CD-ROM.

Maintenance

ACF unit

ENGLISH - 32

*1. The ???i??? appearing after the resolution indicates an interlaced signal. Flicker (line flicker) may be caused in images if interlace is con- nected.

*2. The following symbols are used to indicate picture quality. AA Maximum picture quality can be obtained.

ASignals are converted by the image processing circuit before picture is projected.

BSome loss of data occurs to make projection easier.

*3. Where marked ???D??? signals indicates in Plug and Play is compatible with EDID of projector.

Unmarked signals in Plug and Play may also be compliant if input terminals are written in the format list. Where Plug and Play is unmarked and nothing is written in the format list, difficulties in projecting image may occur even when computer and projector appear to have same resolution.

*4. The following symbols are used to indicate the format.

V = VIDEO, S = S-VIDEO, D = DVI, R = RGB, Y = YPBPR SDI is only for the PT-DZ6710E.

*5. PT-DW6300E/PT-D6000E/PT-D5000E: A

*6. PT-DZ6710E/PT-DZ6700E/PT-D6000E/PT-D5000E: A

*7. PT-DZ6710E/PT-DZ6700E/PT-DW6300E: A

*8. PT-DW6300E/PT-D6000E/PT-D5000E: B

*9. VESA CVT-RB (Reduced Blanking) compatible.

NOTE:

???Projecting an interlaced signal may cause flicker in screen.

???Display dots of each model

Appendix

ENGLISH - 35

Technical Information

Ceiling mount bracket safeguards

The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable provided with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for safety and security.

???Installation work of the ceiling mount bracket should only be carried by a qualified technician according to the following procedure.

???Even if it is guarantee period, the manufacturer is not responsible for any hazard or damage caused by using a ceiling mount bracket which is not purchased from an authorized distributors, or environmental conditions.

???Make sure to use a torque driver and do not use an electrical screwdriver or an impact screwdriver.

???An unused ceiling mount bracket should be removed promptly by qualified technician.

???Do not use other than the provided safety cable (x1) and washers (x2).

???Do not use the screw holes of the front leg adjusters for the projector installation.

???Do not attach the safety cable to the burglar hook port and suspend the projector on it.

???Read the installation instructions booklet that is provided with the ceiling mount bracket to install the safety cable.

???Attachment procedure

Appendix

3.Insert the front leg adjuster through the ring of the washer.

4.Place the front leg adjuster through the loop of the safety cable.

5.Attach the front leg adjuster to the projector by turning clockwise, and then tighten up the front leg adjuster securely.

6. Pull the safety cable outward toward the ceiling.

Ceiling mount

Please also attach the washer which is additional accessory to the ceiling mount.

Washer

Front leg adjuster Washer

Safety cable

ENGLISH - 38