Door Station

Installation and Operation Guide

Model No. VL-GC001A

Thank you for purchasing a Panasonic Door Station.

Please read this Installation and Operation Guide before using the unit and save for future reference.

PFQX2165ZA DC0405NK0

Table of Contents

Important Information

Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Additional safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 For best performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction and Installation

Included items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Location of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installing the door station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Help

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

General Information

Technical data about this product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 FCC and Other Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2

Important Information

Important safety instructions

1)Read these instructions.

All the safety and operating instructions should be read before the appliance is operated.

2)Keep these instructions.

The safety and operating instructions should be retained for future reference.

3)Heed all warnings.

All warnings on the appliance and in the operating instructions should be adhered to.

4)Follow all instructions.

All operating and use instructions should be followed.

5)Do not use this apparatus near water.

For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

6)Clean only with dry cloth.

Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.

7)Do not block any ventilation openings.

Install in accordance with the manufacturer???s instructions.

Slots and Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer???s instructions have been adhered to.

9)Only use attachments / accessories specified by the manufacturer.

10)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

SAVE THESE INSTRUCTIONS

3

Important Information

Additional safety information

1.Use only the power source marked on the unit. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

2.Use only the specified AC adaptor.

3.Do not tamper with the plug.

4.Make sure the plug is securely inserted.

5.Do not touch the plug with wet hands.

6.Do not place objects on the power cord. Install the unit where no one can step or trip on the cord.

7.To reduce the risk of electric shock, do not disassemble this unit. Take the unit to an authorized service center when service is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the unit is subsequently used.

8.Unplug the monitor station from power outlets and refer servicing to an authorized service center when the following conditions occur:

A.If smoke rises, or an unaccustomed noise or smell is discharged from the unit.

B.If metal objects have been dropped inside the monitor station.

9.Do not put your ear(s) near the speaker, as loud sounds emitted from the speaker may cause hearing impairment.

10.Only a qualified technician is allowed to connect a power cable to the unit. Contact an authorized service center.

11.Do not make any wiring connections when the power supply is turned on.

12.Never install wiring during a lightning storm.

13.When existing chime wires are used, it is possible that they contain AC voltage. Electric shock or unit damage could result. Contact an authorized service center.

14.Be sure to install the unit as specified to endure the mass.

15.If the wiring is outdoors, use a protection tube or a surge protector.

16.If the wiring is underground, do not make any connections underground.

17.WARNING ??? Unplug the monitor station from power outlets if it emits smoke, an abnormal smell or makes unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorized service center.

For best performance

LIf a power failure occurs, the unit will not function.

4

Introduction and Installation

Included items

5

5

Introduction and Installation

Location of controls

A

F

B

C

D

E

A Camera

LWhen a visitor presses the Call Button, the camera will turn on and an image of the visitor will be shown on the display of the monitor station.

BMicrophone

CCall Button

LThe Call Button is lit with a blue LED light while the power is on.

LA visitor can press this button to call the monitor station.

DSpeaker

EWater drain hole

LThis hole allows rain water to drain. Do not cover it.

F Camera angle control lever

LThe camera angle can be adjusted when installing the door station (page 7, 10).

6

Introduction and Installation

Before installation

To avoid malfunction or communication disturbances, do not install the door station in the following locations:

???Places where vibration or any other kind of impact occurs.

???Places where echoing is frequent.

???Places where a high concentration of dust, hydrogen sulfide, phosphorus, ammonia, sulfur, carbon, acid, or noxious fumes occur.

???Within 2 m (6'7") of a TV, microwave, personal computer, air conditioner or any other electrical device.

Standard installation position of the door station and camera range

Image range: 650 mm (259/16")

L

R

7

Introduction and Installation

Note:

LThe measurements and angles are for reference purposes and may vary depending on the environment.

LIf a strong light is shining on the door station, the visitor???s face may not be distinguishable. Do not place the door station in the following locations.

???Where most of the background is the sky.

???Where the background is a white wall, and direct sunlight will reflect off it.

???Where direct sunlight will shine on the door station.

???Where echoing occurs, causing the unit to beep frequently.

LMake sure the back of the door station is not subject to water.

Wire type and distance

LWire (between the monitor station and the door station):

Type: General cable CAT-3 24 AWG

Distance: Maximum 100 m (about 328 feet)

8

Introduction and Installation

Installing the door station

Make sure to install the door station on a flat, vertical wall.

Important information:

On the bottom surface of the door station, there is a hole to allow water to drain. Do not cover it up when installing.

1 Unscrew the hex-head screw using the longer end of the allen wrench and remove the mounting bracket from the rear of the door station.

LThe pin hole camera is not a screw to be touched or removed.

Mounting bracket

Pin hole camera

Hex-head screw

(Attached to the door station)

Allen wrench

9

Introduction and Installation

2 Attach the mounting bracket to the wall using the wood screws (3.8 mm x 20 mm, 1/8'' x 13/16'').

LBefore drilling, see page 7 for installation location.

Mounting bracket

83.5 mm (35/16")

Wood screws

Wall

3 Connect the wires that connect to the monitor station to the terminal connector by unscrewing the screws, pushing in the wires, then tightly fastening the screws.

LSee page 8 for the wire type and distance.

LYou can change the camera angle using the camera angle control lever. See page 7 for details.

Wire (Not included)

10

Introduction and Installation

LIf you want to connect the wires without them going through a hole in the wall behind the mounting bracket, connect the wires by passing them through the ribs and the wire hole.

Rib

Wire hole

4 Mount the door station to the mounting bracket.

1

2

Push the door station down until it is secure.

11

Introduction and Installation

5 Insert the hex-head screw using the longer end of the allen wrench.

Hex-head screw

Allen wrench

6 Attach the bolt cover using the shorter end of the allen wrench.

LUse protrusion on the shorter end of the allen wrench to rotate the bolt cover until it is secure.

Allen wrench

12

Help

Cleaning

Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a slightly damp cloth.

Important information:

LDo not use anything containing alcohol, polish powder, powder soap, benzine, thinner, wax, petroleum, or boiling water. Also do not spray with insecticide, glass cleaner, or hair spray. This could cause a change in color or quality.

13

General Information

Technical data about this product

*1 Supplied from the monitor station.

Note:

LDesign and specifications are subject to change without notice.

LThe pictures and illustrations in these instructions may vary slightly from the actual product.

14

General Information

FCC and Other Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate this device.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the monitor station off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna.

???Increase the separation between the equipment and receiver.

???Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

???Consult the dealer or an experienced radio/TV technician for help.

15