Start Here > > >
H3
Bluetooth??
BEFORE YOU
BEGIN
Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions.
Take a moment before you get started to familiarize yourself with your new
H3 Handsfree Headset.
Charge your headset's battery for 2 hours:
Before you can use your headset, you must pair (link) it with your phone.
Call Button
Blue Indicator Light
TROUBLESHOOTING
My phone does not find my headset.
Make sure the blue light on your headset is steadily lit when your phone is searching for devices (see step 2).
My headset worked before but now it's not working.
Make sure your phone is on and the Bluetooth feature is turned on in your phone
Handsfree Headset
Get Connected in
4 Quick Steps
Earhook
Call
Button
1Plug the Motorola charger into the end of the headset.
With the headset power off, press and hold the Call button for 6 to 10 seconds until the blue indicator light turns on and remains steadily lit.
(see step 3). If the Bluetooth feature has been turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 3). If you have confirmed the Bluetooth feature is on in your
1 - CHARGE YOUR
HEADSET
2 - PUT HEADSET
IN PAIR MODE
3 - PAIR PHONE
WITH HEADSET
4 - TEST AND USE
Volume
Buttons
The blue indicator light turns on when the battery is charging. It may take up to 1 minute for the light to turn on. When the headset's battery is fully charged (about 2 hours), the blue indicator light turns off.
2 Unplug the charger from the headset.
Note: Headset is not functional while charging.
Note: The blue light will flash as you press and hold the Call button. Continue holding down the Call button until the blue light is steadily lit.
Note: If you let go of the Call button before the blue light is on and steady, ensure that your headset is off before trying again.
Note: To turn off headset, see "Turning Headset On/Off" on the reverse side of this guide.
phone, pair your phone and headset again (see step 3).
Support.
If you need more help, contact us at
www.hellomoto.com/bluetooth and click
Support.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
Guide Number:
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners.
3 TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
Your phone's Bluetooth feature is off by default. To use your headset, turn on the Bluetooth feature in your phone.
To turn on Bluetooth:
1Select M(Menu) > Settings > Connection > Bluetooth Link > Setup.
2Scroll to Power.
3Press Change.
4Select On.
5Select Back.
6Select Handsfree.
TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
Continued
7 Select [Look for Devices].
Note: Do not select
8Select Motorola H3.
9Select Yes to bond.
10 Enter the passkey 0000 and select OK.
When your headset and phone are successfully paired, the blue light on your headset will change from steadily lit to flashing.
Note: This procedure is for most Motorola phones. For other phones, see your phone's user's guide or visit www.hellomoto.com/bluetoothsupport and click Set Up My New Product.
Your phone and headset are now paired and ready to make and receive calls. To confirm they are operating properly, make a call:
1Place the headset over your ear. See "Wearing the Headset" on the reverse side of this guide.
2On your phone, dial the number you want to call and press the Send key.
3If your phone and headset are successfully paired, you will hear ringing on the headset.
After you have successfully paired your phone and headset, you do not need to repeat these initial setup steps each time you use the headset.
USING YOUR H3
See Features and Functions Guide
on the reverse side
of this guide for information on
using your H3.
?? Motorola, Inc. 2005.
Features and
Functions Guide
H3
TURNING HEADSET
ON/OFF
To turn your headset on, press and hold the Call button until the indicator light flashes. Then, release the button.
WEARING THE
HEADSET
1Open the earhook.
2Loop the earhook over your ear.
CHANGING FOR USE
ON OTHER EAR
You can wear your H3 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:
CHANGING VOLUME
BUTTON ORIENTATION
If you change your headset to wear on the other ear, you can also change the orientation of the volume buttons.
Bluetooth??
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side of this guide
to complete initial setup of your H3.
To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off.
Call
Button
3 Press the headset to your ear.
1Open the earhook 90 degrees from the headset.
2Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it.
3Flip the headset over.
4Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin.
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
1Turn the headset power off.
2Press the Call button along with the Volume button you want to assign as "volume up" button until the indicator light flashes twice.
The headset power turns on.
Call
Button
Volume
Buttons
Note: Your H3 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.
MAKING CALLS CONTINUED
Note: Some features are phone/network dependent.
INDICATOR LIGHTS
The indicator light provides information about your headset status.
Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.
AUDIO TONES
The audio tones provide information about your headset status.