PMC P11 & P12

PCI

PIB

WB-554

ISA

PMC P14 & P15

MVME5100 Block Diagram

M V M E 5 1 0 0 P 2 I / O

M V M E 5 1 0 0 P 2 I / O

I/O Compatibility

Historically, MCG has offered two tracks in its PowerPC VME portfolio. The first track (which includes the MVME2600/ 2700) provides typical single-board computer I/O features including Ethernet, SCSI, multiple serial ports, a parallel port, and a single PMC slot. The on-board I/O is routed to P2 and made available to the user via MCG???s MVME761 or MVME712M transition boards. The second track (which includes the MVME2300/2400) offers limited on-board I/O (Ethernet and a single serial port both via the front panel) but provides dual PMC slots enabling maximum user I/O custom- ization.

The MVME5100 merges the best features of both tracks enabling the OEM to support varying I/O requirements with the same base platform, simplifying part number mainte- nance, technical expertise requirements, and sparing.

P2 I/O Modes

The MVME5100 supports two, jumper-configurable P2 I/O modes, PMC mode and IPMC mode.

PMC mode is backward compatible with the MVME2300/ MVME2400. In PMC mode, 64 pins from PMC Slot 1 and 46 pins from PMC Slot 2 are available on P2 for PMC rear I/O.

In IPMC mode, the MVME5100 supports legacy MVME761 or MVME712M I/O modules (with limited PMC I/O) when an IPMC761 or IPMC712 PMC card is populated in PMC Slot 1. In this configuration, PMC Slot 2 contains some signals that are reserved for extended SCSI.

IPMC Modules

The IPMC761 and IPMC712 are optional add-on PMC mod- ules that provide backward compatibility with previous-gener- ation MCG products (such as MVME2600 and MVME2700)

IPMC Block Diagram

using the MVME761 or MVME712M transition board. IPMC modules provide rear I/O support for

???one single-ended Ultra Wide SCSI port

???one parallel port

???four serial ports (2 or 3 async and 1 or 2 sync/async,

depending on module)

With this PMC card configuration, the memory mezzanine, one PMC slot, and the PMCspan are still available, providing support for OEM product customization.

T r a n s i t i o n M o d u l e s

T r a n s i t i o n M o d u l e s

MVME761

The MVME761 transition module provides industry-standard connector access to the IEEE 1284 parallel port, a 10BaseT or 100BaseT port via an RJ-45 connector, two DB-9 connec- tors providing access to the asynchronous serial ports config- ured as EIA-574 DTE, and two HD-26 connectors providing access to the sync/async serial ports. These serial ports, labeled as Serial 3 and Serial 4 on the faceplate of the MVME761, are individually user-configurable as EIA-232, EIA-530, V.35, or X.21 DCE or DTE via the installation of Motorola Serial Interface Modules (SIMs).

A P2 adapter provides interface module signals to the MVME761 transition module. The 3-row P2 adapter can be used for 8-bit SCSI. A 5-row P2 adapter supports 16-bit SCSI and PMC I/O.

MVME712M

The MVME712M transition module provides industry-stan- dard connector access to the Centronics??parallel port, a nar- row SCSI port, and four DB-25 connectors providing access to the asynchronous/synchronous serial ports jumper config- urable as EIA-232 DCE or DTE. A P2 adapter provides inter-

face signals to the MVME712M transition module. The 3-row P2 adapter can be used for 8-bit SCSI.

To gain access to the additional user definable I/O pins pro- vided via the 5-row VME64 extension connector, a special P2 adapter board is available. This adapter panel replaces the traditional 3-row P2 adapter and extends its capability by pro- viding access to the PMC I/O pins.

S o f t w a r e S u p p o r t

S o f t w a r e S u p p o r t

Firmware Monitor

Firmware must fulfill the traditional functions of test and initial- ization and provide operating system boot support. The MVME5100 firmware monitor exceeds these requirements with a proven monitor from the embedded VME leader. It expands features like power-up tests with extensive diagnos- tics, as well as a powerful evaluation and debug tool for sim- ple checkout or when high-level development debuggers require additional support. All this is included with the MVME5100 firmware; plus it supports booting both operating systems and kernels.

Operating Systems and Kernels

MVME5100 supports booting a variety of operating systems including a complete range of real-time operating systems and kernels which may be purchased from the following com- panies:

Wind River Systems, Inc.: VxWorks??

Multiple Partners: Linux??

S p e c i f i c a t i o n s

S p e c i f i c a t i o n s

M V M E 5 1 0 0 P r o c e s s o r M o d u l e

MVME5100 Processor Module

Processor

Main Memory

Flash Memory

NVRAM

Counters/Timers

VMEbus ANSI/VITA 1-1994 VME64 (IEEE STD 1014)

Controller: Tundra Universe

DTB Master: A16???A32; D08???D64, BLT

DTB Slave: A24???A32; D08???D64, BLT, UAT

Arbiter: RR/PRI

Interrupt Handler/ IRQ 1???7/Any one of seven IRQs

Generator:

System Controller: Yes, jumperable or auto detect

Location Monitor: Two, LMA32

Ethernet Interface

Controller: Two Intel 82559ER

Interface Speed: 10/100Mb/s

PCI Local bus DMA: Yes, with PCI burst

Connector: One routed to front panel RJ-45, one routed to front panel RJ-45 or optionally routed to P2, RJ-45 on MVME761

Asynchronous Serial Ports

Controller: 16C550C UART

Number of Ports: Two, 16550 compatible

Configuration: EIA-574 DTE

Async Baud Rate, bps 38.4K EIA-232, 115Kbps raw max.:

Connector: One routed to front panel RJ-45, one on planar for development use

Dual IEEE P1386.1 PCI Mezzanine Card Slots

Address/Data: A32/D32/D64, PMC PN1, PN2, PN3,

PN4 connectors

PCI Expansion Connector

Address/Data: A32/D32/D64

PCI Bus Clock: 33 MHz

Signaling: 5V

Connector: 114-pin connector located on the planar of the MVME5100

Power Requirements

(not including power required by PMC or IMPC modules)

Board Size

Height: 233.4 mm (9.2 in.)

Depth: 160.0 mm (6.3 in.)

Front Panel Height: 261.8 mm (10.3 in.)

Width: 19.8 mm (0.8 in.)

Max. Component 14.8 mm (0.58 in.)

Height:

Parallel Port

Controller: PC97307

Configuration: 8-bit bi-directional, full IEEE 1284 sup- port; Centronics compatible (minus EPP and ECP on MVME712M)

Modes: Master only

Power Requirements

(additional power load placed on MVME5100 with IPMC installed)

T r a n s i t i o n M o d u l e s

Transition Modules

I/O Connectors

I P M C M o d u l e s

IPMC Modules

PMC Interface

Address/Data: A32/D32/D64, PMC PN1, PN2, PN3,

PN4 connectors

Synchronous

Serial Ports:

PCI Bus Clock: 33 MHz

Signaling: 5V

Module Type: Basic, single-wide; P2 I/O

SCSI Bus

Controller: Symbios 53C895A

PCI Local Bus DMA: Yes, with PCI local bus burst

Asynchronous (8-bit 5.0MB/s mode):

Ultra SCSI: 20.0MB/s (8-bit mode), 40.0MB/s (16-bit mode)

Note: 16-bit SCSI operation precludes the use of some PMC Slot 2 signals.

Synchronous Serial Ports

Controller: 85230/8536

Asynchronous Serial Ports

Controller: 16C550 UART; 85230/8536

Number of Ports: Two (IPMC761); three (IPMC712)

Configuration: EIA-574 DTE (IPMC761);

EIA-232 (IPMC712)

Async Baud Rate, bps 38.4K EIA-232, 115Kbps raw max.:

Board Size

Height: 233.4 mm (9.2 in.)

Depth: 80.0 mm (3.1 in.)

Front Panel Height: 261.8 mm (10.3 in.)

Front Panel Width: MVME761: 19.8 mm (0.8 in.)

MVME712M: 39.6 mm (1.6 in.)

A l l M o d u l e s

All Modules

Environmental

(Minimum of 400 LFM (linear feet per minute) of forced air cooling is recommended for operation in the higher temperature ranges.)

Demonstrated MTBF

(based on a sample of eight boards in accelerated stress environ- ment; results pending for IPMC712)

Mean: 190,509 hours

95% Confidence: 107,681 hours

Safety

All printed wiring boards (PWBs) are manufactured with a flammabil- ity rating of 94V-0 by UL recognized manufacturers.

Electromagnetic Compatibility (EMC)

Intended for use in systems meeting the following regulations: U.S.: FCC Part 15, Subpart B, Class A (non-residential)

Canada: ICES-003, Class A (non-residential)

This product was tested in a representative system to the following standards:

CE Mark per European EMC Directive 89/336/EEC with Amend- ments; Emissions: EN55022 Class B; Immunity: EN55024 (results pending for configurations with IPMC712)

O r d e r i n g I n f o r m a t i o n

O r d e r i n g I n f o r m a t i o n

All models of the MVME5100 are available with either VME Scanbe front panel (-01x1) or IEEE 1101 compatible front panel (-01x3).

MPC750 configurations with 450 MHz MPC750, 17MB Flash and 1MB L2 cache

MVME5100-013x 64MB ECC SDRAM

MVME5100-016x 512MB ECC SDRAM

MPC7400 configurations with 400 MHz MPC7400 and 17MB Flash

MVME5101-013x 64MB ECC SDRAM, 1MB L2 cache

MVME5101-016x 512MB ECC SDRAM, 1MB L2 cache

MVME5101-213x 64MB ECC SDRAM, 2MB L2 cache

MVME5101-214x 128MB ECC SDRAM, 2MB L2 cache

MVME5101-216x 512MB ECC SDRAM, 2MB L2 cache

I/O Modules

MVME712M Compatible I/O

IPMC712-001 Multifunction rear I/O PMC module; Ultra Wide SCSI, one parallel port, three async and one sync/async serial ports

MVME712M Transition module connectors: One DB-25 sync/async serial port, three DB-25 async serial port, one AUI connector, one D-36 par- allel port, and one 50-pin 8-bit SCSI; includes 3-row DIN P2 adapter module and cable

MVME761 Compatible I/O

IPMC761-001 Multifunction rear I/O PMC module; Ultra Wide SCSI, one parallel port, two async and two sync/async serial ports

MVME761-001 Transition module: Two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel port connec- tor, one RJ-45 10/100 Ethernet connector; includes 3-row DIN P2 adapter module and cable (for 8-bit SCSI)

MVME761-011 Transition module: Two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel port connec- tor, and one RJ-45 10/100 Ethernet connec- tor; includes 5-row DIN P2 adapter module and cable (for 16-bit SCSI); requires back- plane with 5-row DIN connectors

SIM232DCE or DTE EIA-232 DCE or DTE Serial Interface Module

SIM530DCE or DTE EIA-530 DCE or DTE Serial Interface Module

SIMV35DCE or DTE V.35 DCE or DTE Module

SIMX21DCE or DTE X.21 DCE or DTE Serial Interface Module

Related Products

PMCSPAN-002 Primary 32-bit PCI expansion, mates directly to the MVME5100 providing slots for either two single-wide or one double-wide PMC cards; optional PMCSPAN-010

Documentation

Documentation is available for online viewing and ordering at http:// www.motorola.com/computer/literature.