Overview of the Parent Unit

Parent unit menu icons

1Signal Level (5 Levels)

N Night Vision Mode (Screen changes to Black/White)

T Talk Mode

JPan Right

KTilt Up

LTilt Down

1. Safety Instructions

WARNING:

STRANGULATION HAZARD - Keep the unit and adapter cord more than 3 feet from the crib and out of baby's reach. NEVER place camera or cords within the crib.

Secure the cord more than 3 feet away from baby's reach. Never use extension cords with AC Adapters. Only use the AC Adapters provided.

CAMERA SET UP & USE:

???Determine a location for the CAMERA that will provide the best view of your baby in his cot.

???Place the CAMERA on a flat surface, such as a dresser, bureau, or shelf.

???NEVER place camera or cords within cot.

WARNING

This baby monitor is compliant with all relevant standards regarding electromagnetic fields and is, when handled as described in the User's Guide, safe to use. Therefore, always read the instructions in this User's Guide carefully before using the device.

???Adult assembly is required. Keep small parts away from children when assembling.

???This product is not a toy. Do not allow children to play with it.

???This baby monitor is not a substitute for responsible adult supervision.

???Keep this user's guide for future reference.

???Do not place the baby unit or cords in the crib or within reach of the baby (the unit and cords should be more than 3 feet away).

???Keep the cords out of reach of children.

???Do not cover the baby monitor with a towel or blanket.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

2. Getting Started

2.1Baby Unit Power Supply

1.Connect the small plug of the power adapter to the baby unit and the other end to the electrical outlet.

NOTE

Only use the enclosed power adapter (5.9V DC / 1000mA).

2.Slide the ON/OFF switch to the ON position. The power LED will light up in green.

3.Slide the ON/OFF switch to the OFF position to turn the Baby Unit off.

2.2Parent Unit Battery Installation

Black Red

1.Insert the wire tab of the rechargeable battery pack into the contact slot as shown above and fit the battery pack into the compartment.

Small cross head or

Flat end screw driver

2.Replace the battery cover over the compartment and gently tighten the screw in a clockwise direction using a Small cross head or Flat end screw drivers.

IMPORTANT

Installing the rechargeable battery pack and charging it fully before use is recommended. This will allow the unit to operate on battery in the event of a power failure.

1.Connect the small plug of the power adapter to the parent unit and the other end to the electrical outlet. Only use the enclosed power adapter (6V DC/500mA).

2.Press and hold the P POWER ON/OFF button for 1 second to turn ON the parent unit.

3.Once the baby and parent units are switched on, the display on the parent unit will show the video captured by the baby unit.

4.If there is no connection or you are out of range, the video display will go off and the words No Signal will be shown on the LCD display, and the unit will beep every 5 seconds. Move the parent unit closer to the baby unit until the link is re-established.

5.Press and hold the PPOWER ON/OFF button, until the progress bar finishes scrolling, to turn OFF the parent unit.

gives a beep every 16 seconds. The battery needs to be recharged. The battery pack takes about 16 hours to charge fully.

When charging

1.During power OFF, when adapter is plugged in, a adapter logo will display on screen and then a flashing battery logo will display for 45 sec. The Blue LED at top left corner light up indicates adapter is plugged in.

2.During power ON, when adapter is plugged in, the battery icon on screen's top right corner will show that the battery is charging. The Blue LED at the top left corner light up indicates adapter is plugged in.

2.4Registration (Pairing)

The Baby monitor is pre-registered to your Parent Unit. You do not need to register it again unless the Baby Unit loses its link with the Parent Unit.

To re-register your Baby Unit, or register a new Baby Unit, follow the procedure below:

1.Press the Mbutton of the parent unit and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until Cis highlighted, and the del/add/view/scan menu will pop up.

3.Press the +UP button or -DOWN button to select ADD, and press the OK button to confirm.

4.CAM 1 / CAM 2 / CAM 3 / CAM 4 will pop up, press the + UP button or - DOWN button to select the desired CAM and press the OK button to start searching for a camera unit. The green audio level LED will flash rapidly while searching.

5.Press the OK button to confirm.

6.Press and hold the PAIR button underneath the baby unit until the parent unit finds the camera, beeps and the video from the camera appears.

NOTE

If a particular Baby Unit was registered previously, registering this current Baby Unit again will overwrite the old registration.

2.5View Video Through TV

Connect a suitable AV cable into the AV OUT socket on the side of the Parent Unit and into the AV input of the TV. Scroll through the AV inputs on the TV menu until the Baby monitor picture is visible.

AV cable is an optional accessory, which is to be purchased separately.

NOTE

The Monitor's power button must be turned ON and CAM pre-selected before connecting the AV cable. Once the AV cable is connected, the Monitor's controls cannot be activated.

4. Parent Unit Menu Options

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or > button until m is highlighted.

3.Press the +UP button or -DOWN button to select the desired song from the 5 lullabies available, or the cycle option to play all 5 songs in turn. If an individual song is selected it will only play once and then stop. (The default setting is lullaby OFF)

4.Press OK on the selected lullabies to select the desired song sound level.

4.4Zoom

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or > button until Z is highlighted.

3.Press the +UP button or -DOWN button to select the 1X or 2X Zoom. (The default setting is 1X.)

TIP

Quick Method to View Cameras instead of entering into the menu bar. Directly press OK repeatedly to select CAM 1, CAM 2, CAM 3, CAM 4, SCAN.

4.6.3 Delete a camera

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until Cis highlighted, and the del/add/view/scan menu will pop up.

3.Press the +UP button or -DOWN button to select DEL, and press the OK button to confirm.

4.CAM 1/CAM 2/CAM 3/CAM 4 will pop up, press the + UP button or - DOWN button to select the desired CAM, and press the OK button to delete that registration.

4.6.4 Scan camera

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until Cis highlighted, and the del/add/view/scan menu will pop up.

3.Press the +UP button or -DOWN button to select SCAN, and press the OK button to confirm.

4.The screen will then display images from different registered cameras in a loop of CAM 1/CAM 2/CAM 3/CAM 4, changing about every 12 seconds.

TIP

Quick Method to View Cameras instead of entering into the menu bar. Directly press OK repeatedly to select CAM 1, CAM 2, CAM 3, CAM 4, SCAN.

4.7Temperature

1.Press the Mbutton and the menu bar will pop up.

2.Press the < LEFT button or >RIGHT button until tis highlighted.

3.Press the +UP button or -DOWN button to select ??C or ??F.

6. Cleaning

Clean the MBP36, MBP36/2, MBP36/3, MBP36/4, MBP36P, MBP36P/2, MBP36P/3, MBP36P/4 with a slightly damp cloth or with an anti-static cloth. Never use cleaning agents or abrasive solvents.

Cleaning and care

???Do not clean any part of the product with thinners or other solvents and chemicals ???- this may cause permanent damage to the product which is not covered by the warranty.

???Keep your MBP36, MBP36/2, MBP36/3, MBP36/4, MBP36P, MBP36P/2, MBP36P/3, MBP36P/4 away from hot, humid areas or strong sunlight, and don't let it get wet.

???Every effort has been made to ensure high standards of reliability for your MBP36, MBP36/2, MBP36/3, MBP36/4, MBP36P, MBP36P/2, MBP36P/3, MBP36P/4. However, if something does go wrong, please do not try to repair it yourself ???- contact Customer Service for assistance.

Interference

Noise interference on your parent unit

???Your baby and parent units may be too close. Move them farther apart.

???Make sure there is at least 3 to 6 feet between the 2 units to avoid audio feedback.

???lf the baby unit is too far away it may be out of range, so move the baby unit closer to the parent unit.

???Make sure the baby and parent units are not near other electrical equipment, such as a television, computer or cordless/mobile telephone.

???Use of other 2.4GHz products, such as wireless networks (Wi-Fi?? routers), Bluetooth?? systems, or microwave ovens, may cause interference with this product, so keep the baby monitor away at least 5ft (1.5m) from these types of products, or turn them off if they appear to be causing interference.

???If the signal is weak, try moving the Parent and/or Baby Unit to different positions in the rooms.

What Other Limitations Are There?

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE

DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE

REPAIR OR REPLACEMENT PROVIDED UNDER THIS EXPRESS

LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE

CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL

MOTOROLA OR BINATONE BE LIABLE, WHETHER IN CONTRACT

OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS

OF THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY, OR

FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL

DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS,

LOSS OF BUSINESS, LOSS OF INFORMATION OR OTHER

FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE

ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES

TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.

Some jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights that vary from one jurisdiction to another.

Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage.

Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this Warranty.

Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or

(d) other acts which are not the fault of MOTOROLA or BINATONE, are excluded from coverage.

Use of Non-Motorola branded Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products or Accessories or other peripheral equipment are excluded from coverage.

Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than MOTOROLA, BINATONE or its authorized service centers, are excluded from coverage.

Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola branded housings, or parts, are excluded from coverage.

Communication Services. Defects, damages, or the failure of Products or Accessories due to any communication service or signal you may subscribe to or use with the Products or Accessories is excluded from coverage.

How to Obtain Warranty Service or Other Information?

To obtain service or information, please call:

US and Canada 1-888-331-3383

You will receive instructions on how to ship the Products or Accessories at your expense and risk, to a BINATONE Authorized Repair Center.

To obtain service, you must include: (a) the Product or Accessory; (b) the original proof of purchase (receipt) which includes the date, place and seller of the Product; (c) if a warranty card was included in your box, a completed warranty card showing the serial number of the Product; (d) a written description of the problem; and, most importantly; (e) your address and telephone number.

These terms and conditions constitute the complete warranty agreement between you and BINATONE regarding the Products or Accessories purchased by you, and supersede any prior agreement or representations, including representations made in any literature publications or promotional materials issued by BINATONE or representations made by any agent employee or staff of BINATONE, that may have been made in connection with the said purchase.

WARNING

Changes or modifications, to this equipment not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment.

Industry Canada

This device complies with Industry Canada licence-exempt RSS standard(s): Operation is subject to the following Two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The term "IC: " before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.

Technical Specifications

Baby unit (Model: MBP36BU)