Installation and Operating Guide | Warranty

Model Numbers | Z44SZ80/Z52SZ80 | DLP PROJECTION

?? Copyright 2005, LG Electronics USA, Inc.

Warning/Caution

Warning/Caution

WARNING/CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ???dangerous voltage??? within the product???s enclosure that may be of suffi- cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli- ance.

WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ??VITER LES CHOCS ??LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU???AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer???s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user???s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod- ification could void the user???s authority to operate this product.

COMPLIANCE:

The responsible party for this product???s compliance is: Zenith Electronics Corporation

1-201-816-2000

Marked and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 http://www.zenith.com

2 DLP Projection TV

Safety Instructions

Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appara- tus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled ???Important Safety Instructions???. The following safety instructions shall be includ- ed where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer???s option, a picture or drawing that illus- trates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer???s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli- fiers)that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

PORTABLE CART WARNING

Owner???s Manual 3

Safety Instructions

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

15.CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of

this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

16.Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.

17.Wet Location :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

4 DLP Projection TV

Contents

Contents

After reading this manual, keep it handy for future reference.

Owner???s Manual 5

Introduction

Introduction

Controls

-This is a simplified representation of a front panel.

-Image shown may be somewhat different from your TV.

Front Panel Controls

Function Status Indicators

-Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal the operating status of the DLP projection TV.

6 DLP Projection TV

Introduction

Connection Options

Back Connection Panel

Note: 1 In standby mode, these port will not work.

Owner???s Manual 7

Introduction

Front Connection Panel

There are four jacks on the left side on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple.

The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connect- ed to the front connection panel.

To use the side jacks as the signal source, select them using Main Input menu as described on page 23. They will be named ???Front Video??? in the Main Input menu.

Mini glossary

A/V CABLESAudio/Video cables. Three cable connector???Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).

8 DLP Projection TV

Introduction

Remote Control Key Functions

- When using the Remote Control, aim it at the remote control sensor on the TV.

Owner???s Manual 9

Introduction

Remote Control Key Functions

10 DLP Projection TV

Installation

Installation

External Equipment Connections

Antenna or Cable Connection

1. Analog and Digital TV signals provided on antenna

-Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections

-For optimum picture quality, adjust antenna direction if needed.

2. Analog and Digital TV signals provided on cable

Copper Wire

Owner???s Manual 11

Installation

3. Analog and Digital TV signals provided on cable and antenna

Note: The TV will let you know when the TV(analog antenna), DTV(digital antenna), CATV(analog cable) and CADTV(digital cable) channel scans are complete.

12 DLP Projection TV

Installation

DVD Setup

Owner???s Manual 13

Installation

HDSTB Setup

-This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

-This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Monitor Out Setup

14 DLP Projection TV

Installation

PC Setup

-This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

-The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly.

<When the PC supports DVI>

How to connect

1.Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product). If you do not need to connect audio, HDMI2 port is also available for the DVI video connection.

2.If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGI- TAL AUDIO(OPTICAL) port for DVI INPUT.

3.If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port.

How To Use

1.To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2.Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.23)

TV/VIDEO button is also available for this purpose.

3.Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

<When the PC supports RGB>

How to connect

1.Connect the PC to RGB INPUT port of this TV with a RGB cable.

2.If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port.

How To Use

1.To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz.

2.Select RGB-PC input source in main input option of SETUP menu.(Refer to P.23)

Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose.

3.Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

Monitor Display Specifications (RGB-PC or HDMI1/DVI Mode)

Owner???s Manual 15

Installation

16 DLP Projection TV

Installation

HDMI

-HDMITM, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing.

-This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).

-This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolu- tions.

-When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output resolution of the source device will be automatically set to 1280x720p.

-If the source device does not support Auto HDMI/DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's output resolution to 1024x768, 60Hz.

-If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes both video and audio.

-If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.

<When the source device(DVD player or Set Top Box) supports HDMI>

How To Connect

1.Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product).

2.No separated audio connection is necessary.

How To Use

-If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

-If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

-Select HDMI1/DVI or HDMI2 input source in main input option on the SETUP menu.(Refer to P.23) TV/VIDEO button is also available for this purpose.

<When the source device(DVD player or Set Top Box) supports DVI>

How To Connect

1.Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product). Do not use HDMI2 port for DVI connection if you want to connect audio.

2.A separated audio connection is necessary.

3.If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI

INPUT.

4.Connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port.

How To Use

-If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

-If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

-Select HDMI1/DVI input source in main input option on the SETUP menu.(Refer to P.23)

TV/VIDEO button is also available for this purpose.

Owner???s Manual 17

Installation

Reference

Cable sample

HDMI Cable

(not supplied with the product)

HDMI to DVI Cable

(not supplied with the product)

Fiber Optic Digital Audio Cable (not supplied with the product)

Analog Audio Cable(RCA type) (not supplied with the product)

Analog Audio Cable(Stereo to RCA type) (not supplied with the product)

18 DLP Projection TV

Installation

How to use

1.Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET.

2.Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control.

3.Select HDMI1/DVI Input source in Main Input option on the SETUP menu.(Refer to P.23)

4.Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.

Notes:

-Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.

-When Source Devices connected with HDMI1/DVI Input, output TV SET Resolution(480p, 720p, 1080i) and TV SET Display fit

EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service cen- ter.

-In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center.

In DTV Mode, the Supported TV Set Resolution Specification

-1920 x 1080 I @ 59.94Hz / 60Hz, 16:9

-1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)

-720 x 480 P @ 59.94Hz / 60Hz, 16:9

-720 x 480 P @ 59.94Hz / 60Hz, 4:3

In PC Mode, the Supported PC Resolution Specification

-640 x 480 @ 60Hz

-640 x 480 @ 72Hz

-640 x 480 @ 75Hz

-800 x 600 @ 56Hz

-800 x 600 @ 60Hz

-800 x 600 @ 72Hz

-800 x 600 @ 75Hz

-1024 x 768 @ 60Hz(preferred format)

-1024 x 768 @ 70Hz

-1024 x 768 @ 75Hz

Owner???s Manual 19

Operation

Operation

Turning the TV On

*In this manual, the OSD (On Screen Display) may be different from your TV???s because it is just an example to help you with the TV operation.

Turning on the TV just after installation

1.Connect power cord correctly. At this moment, the TV is switched to standby mode.

2.Press the POWER or CH (D / E) buttons on the TV front panel or press the POWER, TV/VIDEO, TV INPUT, CH (D / E) or Number (0 ~ 9) buttons on the Remote Control to turn the TV on.

Turning on the TV (power cord is still connected)

1. If the TV is off without indicators on the TV

??? Check the power cable.

2.If the TV was turned off with the remote control and the POWER button on the TV

???Press the POWER button on the TV or press the POWER, TV/VIDEO, TV INPUT, CH (D / E) or Number (0 ~ 9) button on the Remote Control to turn the TV on.

Note: If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

20 DLP Projection TV

Operation

TV Setup

On-screen Menus Language Selection

- The menus can be shown on the screen in the selected language. First select your language.

1.Press the MENU button and then use D / E button to select the OPTION menu.

2.Press the G button and then use D / E button to select Language.

3.Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected lan- guage.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Owner???s Manual 21

Operation

Setup Menu Options

EZ Scan (Channel Search)

-Automatically finds all channels available through antenna and cable inputs, and stores them in a channel list in the memory.

-Run EZ Scan again after any Antenna/Cable connection changes.

1.Press the MENU button and then use D / E button to select the SETUP menu.

2.Press the G button and then use D / E button to select EZ Scan.

3.Press the G button or ENTER button to begin the channel search.

Allow EZ Scan to complete the channel search cycle for TV, DTV, CATV, and CADTV.

Channel Edit

-You can create two different types of channel lists in memory: ???Custom List??? and ???Favorite List??? from the default channel list created from the EZ Scan channel search.

-A Custom List can be created by toggling each channel on or off with ENTER button. The channels in the Custom List are displayed in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen.You can also create your own Favorite List.

Use the FAV button on the Remote Control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List.

1.Press the MENU button and then use D / E button to select the SETUP menu.

2.Press the G button and then use D / E button to select Channel Edit.

3.Press the G button. You will now see a screen filled with channel numbers and a preview picture.

4.Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV to add or delete the channel to the Favorite List.

5.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

22 DLP Projection TV

Operation

Channel Label Setup

-Choose preset labels for your channels.

-If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a DTV chan- nel - even if you didn't preset a label for the channel.

1.Press the MENU button and then use D / E button to select the SETUP menu.

2.Press the G button and then use D / E button to select Channel Label.

3.Press the G button. You will now see a screen filled with Labels and a preview screen.

4.Use the CH D / E button to select a channel to Label.

5.Use D / E / F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to the selected channel.

CNN

Main Picture Source Selection

-Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV.

1.Press the MENU button and then use D / E button to select the SETUP menu.

2.Press the G button and then use D / E button to select Main Input.

3.Press the G button and then use D / E button to select the source: Antenna, Cable, Video1, Video2, Front Video, Component1, Component2, RGB-DTV (or

RGB-PC), HDMI1/DVI or HDMI2.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Input Label

1.Press the MENU button and then use D / E button to select the SETUP menu.

2.Press the G button and then use D / E button to select Input Label.

3.Press the G button and then use D / E button to select the source: Video1, Video2, Front Video, Component1, Component2, RGB, HDMI1/DVI or HDMI2.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Owner???s Manual 23

Operation

Video Menu Options

EZ Picture

-EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category.

-When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ

Picture automatically changes to Custom.

-Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable.

1.Press the EZ Video button repeatedly to select the picture appearance setup option as shown below:

Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports.

???You can also use the VIDEO menu to adjust EZ Picture.

2.Press the EXIT button to save and return to TV viewing.

Manual Picture Control (Custom option)

- Adjust the picture appearance to suit your preference and viewing situations.

1.Press the MENU button and then use D / E button to select the VIDEO menu.

2.Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, or Tint).

3.Press the G button and then use F / G button to make appropriate adjustments.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Color Temperature Control

-Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue.

1.Press the MENU button and then use D / E button to select the VIDEO menu.

2.Press the G button and then use D / E button to select Color Temperature .

3.Press the G button and then use D / E button to select either Cool, Medium, or Warm.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Video Reset

-Use to quickly reset all the Video menu options to their original factory preset values.

1.Press the MENU button and then use D / E button to select the VIDEO menu.

2.Press the G button and then use D / E button to select Video Reset .

3.Press the G button to reset the Video menu options to original values.

24 DLP Projection TV

Operation

EZ Sound

-EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content.

-When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Custom.

-Normal, Stadium, News, Music and Theater are preset for good sound quality at the factory and are not adjustable.

1.Press the EZ Sound button repeatedly to select the appropriate sound setup as shown below:

Custom (your own settings), Normal, Stadium, News, Music and Theater.

??? You can also adjust EZ Sound in the AUDIO menu.

2.Press EXIT button to save and return to TV viewing.

Manual Sound Control (Custom option)

- Adjust the sound to suit your taste and room situations.

1.Press the MENU button and then use D / E button to select the AUDIO menu.

2.Press the G button and then use D / E button to select the desired sound option

(Balance, Treble, or Bass).

3.Press the G button and then use F / G button to make appropriate adjustments.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Owner???s Manual 25

Operation

Audio Menu Options

Front Surround

- is a trademark of SRS Labs, Inc.

-TruSurround XT technology is incorporated under license from SRS Labs, Inc.

-Manufactured under license from Dolby Laboratories. ???Dolby??? and the double-D symbol are trademarks of Dolby Laboratories.

1.Press the MENU button and then use D / E button to select the AUDIO menu.

2.Press the G button and then use D / E button to select Front Surround.

3.Press the G button and then use D / E button to select Off sor SRS (Sound Retrieval System) TruSurround XT.

??? SRS TruSurround XT

Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

TV Speaker On/Off Setup

-Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off.

1.Press the MENU button and then use D / E button to select the AUDIO menu.

2.Press the G button and then use D / E button to select TV Speaker.

3.Press the G button and then use D / E button to select On or Off .

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Stereo/SAP Broadcasts Setup

-This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one.

-When having selected Stereo or SAP button on the Remote Control, this TV can only receive the signal when the TV station transmits the proper signals.

-Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

-Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting.

-Stereo or SAP can be received in Analog channel.

1.Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono, Stereo, or SAP appear in turn.

??? If other languages available on the digital signal, select them with the SAP button.

2.Press EXIT button to save and return to TV viewing.

26 DLP Projection TV

Operation

Time Menu Options

Auto Clock Setup

-The time is set automatically from a digital channel signal.

-The digital channel signal includes information for the current time provided by the broadcasting station.

-Set the clock manually, if the current time is set incorrectly by the auto clock function.

1.Press the MENU button and then use D / E button to select the TIME menu.

2.Press the G button and then use D / E button to select Auto Clock.

3.Press the G button and then use D / E button to select On.

4.Press the G button and then use D / E button to select your viewing area time zone: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.

5.Press the G button and then use D / E button to set Daylight Saving Auto, Off or On, depending on whether or not your viewing area observes Daylight Savings Time.

6.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Manual Clock Setup

- If current time setting is wrong, reset the clock manually.

1.Press the MENU button and then use D / E button to select the TIME menu.

2.Press the G button and then use D / E button to select Manual Clock.

3.Press the G button and then use F / G button to select either the year, date, or time option. Once selected, use the D / E button to set the year, date, and time options.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

On/Off Timer Setup

-Timer function operates only if current time has been set.

-Off-Timer function overrides On-Timer function if they are both set to the same time.

-The TV must be in standby mode for the On-Timer to work.

-If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.

1.Press the MENU button and then use D / E button to select the TIME menu.

2.Press the G button and then use D / E button to select Off Timer or On Timer.

3. Press the G button and then use D / E button to select On.

???To cancel On/Off timer function, select Off.

4.Press the G button and then use D / E button to set the hour.

5.Press the G button and then use D / E button to set the minutes.

6.For only On timer function

Press the G button and then use D / E button to select the channel at turn-on.

Press the G button and then use D / E button to set the sound level at turn-on.

7.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Owner???s Manual 27

Operation

Time Menu Options

Sleep Timer

-The Sleep Timer turns the TV off after a preset amount of time. Note that this setting is cleared when the TV is turned off.

-You can also set up the Sleep Timer in the TIME menu.

1.Press the SLEEP button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2.When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected.

3.To check the remaining minutes before the TV turns off, press the SLEEP button once.

4.To cancel the Sleep Timer, press the SLEEP button repeatedly to select Off.

Auto Off

-If set to on and there is no input signal, the TV turns off automatically after 10 minutes.

1.Press the MENU button and then use D / E button to select the TIME menu.

2. Press the G button and then use D / E button to select Auto Off.

3.Press the G button and then use D / E button to select On or Off.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

28 DLP Projection TV

Operation

Option Menu Options

Aspect Ratio Control

-Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be dis- played.

-Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/HDMI1/DVI-DTV(720p/1080i), HDMI2- DTV(720p/1080i)/ CADTV, DTV(720p/1080i) input source.

-RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.

1.Press the RATIO button repeatedly to select the desired picture format. You can also adjust the Aspect Ratio in the OPTION menu.

???Set By Program

Selects the proper picture proportion to match the source???s image. (4:3 ??? 4:3, 16:9 ??? 16:9)

???4:3

Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides.

???16:9

Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

???Horizon

Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.

???Zoom 1

Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.

???Zoom 2

Choose Zoom 2 when you want the picture to be altered, both horizontally extended and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage.

???Cinema Zoom

Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted.

You can adjust the enlarge proportion of Cinema Zoom using D / E button. The adjustment range is 1~16.

Cinema 3:2 Mode Setup

-Most movies are 24 frames/sec, but TV signal is 30 frames/sec. This option lets the TV do 3:2 pull-down operation for you to watch movies with the best motion appearance.

1.Press the MENU button and then use D / E button to select the OPTION menu.

2.Press the G button and then use D / E button to select Cinema 3:2 Mode.

3.Press the G button and then use D / E button to select On or Off.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Note: This feature operates only in 480i mode.

Owner???s Manual 29

Operation

Option Menu Options

Caption

1.Press the MENU button and then use D / E button to select the OPTION menu.

2.Press the G button and then use D / E button to select Caption.

3.Press the G button and then use D / E button to select On or Off.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Caption/Text

Analog Broadcasting System Captions

-Select a caption mode for displaying captioning information if provided on a program.

-Analog caption displays information at any position on the screen usually the program's dialog.

-Text displays information, usually at the bottom position and is used for a data service, generally not program related.

-Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.

-This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off.

1.Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4.

???EZ Mute shows the selected captions option (if available on program) when the TV sound is muted

2.Press EXIT button to save and return to TV viewing.

???You can also use the OPTION menu to select Caption/Text.

1.Press the MENU button and then use D / E button to select the OPTION menu.

2.Press the G button and then use D / E button to select Caption/Text.

3.Press the G button and then use D / E button to select caption: CC1, CC2, CC3,

CC4, Text1, Text2, Text3, or Text4.

???CAPTION

The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.

???TEXT

The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

4.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

30 DLP Projection TV

Operation

Caption Option

-Customize the DTV/CADTV captions that appear on your screen.

1.Press the MENU button and then use D / E button to select the OPTION menu.

2.Press the G button and then use D / E button to select Caption Option.

3.Press the G button and then use F / G button to select Custom.

4.Use D / E button to customize the Style, Font, etc., to your preference. A pre- view icon is provided at the bottom of the screen, use it to see the caption lan- guage.

???Size: Set the size the words will appear in.

???Font: Select a typeface for the words.

???Text Color: Choose a color for the text.

???Text Opacity: Specify the opacity for the text color.

???Bg (Background) Color: Select a background color.

???Bg (Background) Opacity: Select the opacity for the background color.

???Edge Type: Select an edge type.

???Edge Color: Select a color for the edges.

5.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

EZ Demo

Shows you how to navigate the TV's on-screen menus.

EZ Demo Use to scan the features and menu options available on your TV.

1.Press the MENU button and then use D / E button to select the OPTION menu.

2.Press the G button and then use D / E button to select EZ Demo, then use the G button to start EZ Demo.

3.Press EXIT button to stop EZ Demo.

.

Owner???s Manual 31

Operation

Lock Menu Options

Parental Control can be used to block specific channels, ratings and other viewing sources.

The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1.Set ratings and categories to be blocked.

2.Specify a password

3.Enable the lock

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.

Ratings for Movies previously shown in theaters:

If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

??? RGB, HDMI1/DVI or HDMI2 (On, Off)

32 DLP Projection TV

Operation

Parental Lock Setup

-Set up blocking schemes to block specific channels, ratings, and external viewing sources.

-A password is required to gain access to this menu.

1.Press the MENU button and then use D / E button to select the LOCK menu.

Then, press the G button

???Enter the password as requested.

???The TV is set up with the initial password ???0-0-0-0???.

2.Use the D / E button to choose from the following Lock Menu options. Once the option is selected, change the settings to your preference.

???Lock System: Activates or disables the blocking scheme you set up previ- ously.

???Set Password: Change the password by inputting a new password twice.

???Block Channel: Blocks any channels that you do not want to watch or that you do not want your children to watch.

???Movie Rating (MPAA): Blocks movies according to the movie ratings lim- its specified, so children cannot view certain movies. You can set the rat- ings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.

???TV Rating-Children: Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intend- ed for mature audiences in the TV Rating - sub menu, your children can view those programs.

???TV Rating-General: Based on the ratings, blocks certain TV programs that you and your family do not want to view.

???Input Block: Enables you to select a source to block from the external source devices you have hooked up.

3.Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Note : If you ever forget your password, key in ???7???, ???7???, ???7???, ???7??? on the Remote Con trol.

Owner???s Manual 33

Operation

Remote Control

PIP (Picture-In-Picture) / Twin Picture

-PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image.

-Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen.

-If you set the block/rating for Lock menu options in PIP/Twin Picture mode, ???Rating Blocked??? doesn???t display on screen.

Watching PIP/Twin Picture

Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.

PIP Mode

Twin Picture Mode

PIP Off

Selecting an Input Signal Source for PIP/Twin Picture

Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. You can also select sources for the Sub Input in the SETUP menu.

Swapping the PIP/Twin Picture

Repeatedly, use the SWAP button to switch the main and sub pictures.

???Component 1, Component 2, RGB-PC (or RGB-DTV), HDMI1/DVI, HDMI2 input sources for the main picture can???t be used to swap the main and sub pictures.

TV Program selection for PIP

1.Press the PIP button.

2.Select the Antenna or Cable option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+ / PIPCH- button to select a channel for the sub picture.

(You can???t select TV for main and sub picture simultaneously).

34 DLP Projection TV

Operation

Moving the PIP sub picture

In PIP mode, press the D / E / F / G button to move the sub picture to a different location on the screen.

Adjusting Main and Sub Picture Sizes for Twin Picture

Use the D / E / F / G button to change main and sub picture sizes in Twin Picture mode.

Owner???s Manual 35

Operation

36 DLP Projection TV

Operation

EZ Mute

-If you set the Caption on, nothing to do with the MUTE button, Caption function operates as Caption on or off.

-When you repeatedly press the MUTE button, the screen is displayed in turn. (Refer to the lower picture)

24

Mute Off : Sound is enabled.

Note: EZ Mute only operates in DTV/Analog/Video/Front Video.

Split Zoom (DTV 720p, or 1080i mode only)

-Enlarges the picture with correct proportions.

-When enlarging the picture, the image may become distorted.

1. Press the FREEZE button in DTV 720p, or 1080i modes.

2. Use the D / E / F / G buttons to select the screen split zoom section. 3. To return to normal viewing, press the FREEZE button again.

Owner???s Manual 37

Operation

Screen Setup for PC mode

Operation

???When RGB connect to PC input and select the RGB-PC in Main Input, this function is used.

???In RGB-DTV mode, SIZE is not available.

Adjustment for screen Position, Size, Phase, Reset

???After connecting RGB-PC to PC input and checking the screen quality.

- Display PC Adjust Menu using ADJUST button.

38 DLP Projection TV

Programming the Remote

Programming the Remote

The Remote Control for your HD receiver is a multi-brand or universal Remote Control that can be programmed to operate most remote-controllable devices of other manufacturers.

Note: The Remote Control may not be able to control all models of other brands.

Owner???s Manual 39

Programming Codes

Programming Codes

TVs

40 DLP Projection TV

Programming Codes

SAT

Audio

Owner???s Manual 41

Troubleshooting Checklist

Programming Codes

DVD

42 DLP Projection TV

Troubleshooting Checklist

Troubleshooting Checklist

Owner???s Manual 43

Troubleshooting Checklist

Troubleshooting Checklist

Poor TV input

Poor Video

Unsuitable

??? You can adjust the RATIO button or Aspect Ratio in the OPTION menu.

Aspect Ratio

44 DLP Projection TV

Maintenance

Maintenance

-Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

1.Here???s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it???s almost dry, and then use it to wipe the screen.

2.Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

Please be sure not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for a long time (such as a vacation), it???s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

Owner???s Manual 45

Product Specification

Product Specifications

??? The specifications shown above may be changed without prior notice for quality improvement.

46 DLP Projection TV

Notes

Owner???s Manual 47

ZENITH ELECTRONICS CORPORATION

DLP Projection TV Limited Warranty - USA

Zenith will repair or replace your product, at Zenith???s option, if it proves to be defective in material or workmanship under normal use, during the warranty period ("Warranty Period") listed below, effective from the date ("Date of Purchase") of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, excluding U.S. Territories.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-

ING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW,

IT IS LIMITED IN DURATION TO THE EXPRESSED WARRANTY PERIOD ABOVE. ZENITH

WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNI-

TIVE DAMAGES OF ANY NATURE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAM-

AGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, LOST OR COR-

RUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CON- TRACT, TORT, OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts, so the above exclu- sion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that may vary from state to state.

THIS LIMITED WARRANTY DOES NOT APPLY TO:

1.Damages or operating problems that result from shipping, installation, adjustment of user con- trols, calibration, maintenance or failure to maintain, or separate system components; and

2.Damages or operating problems that result from normal wear and tear, misuse, abuse, operation out- side environmental specifications or contrary to the requirements or precautions in the Operating Guide, accident, lightning strikes or other natural causes, unauthorized modification or alteration, incorrect electri- cal current or voltage, reception problem caused by inadequate home antenna or faulty antenna con- nections, computer software, institutional or commercial use, or other causes not arising out of defect in material or workmanship.

3.Therefore, the cost of repair or replacement of such a defective product shall be borne by the con- sumer.

CUSTOMER INTER-ACTIVE CENTER NUMBERS: