1

2

3

4

5

OUTSTANDING PERFORMANCE

Not to mention unmatched big capacity, you can benefit from good time efficiency, quiet operation and energy saving system.

DOUBLE-COATED STEEL DRUM

It is coated with one metal coating and the other polymer coating in order to guarantee high durability and the long life.

ARTISTIC DESIGN

Modern front panel look and big crystal-clear glass door make your house look stylish.

DIGITAL FABRIC CARE

Multi-level temperature control heater takes a better care on your valued clothes.

EASY OF USE

A whole selection of user-friendly functions always make you comfortable with dryer operation.

1)Read all instructions before using the appliance.

2)Do not dry articles that have come into contact with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

3)Do not allow children to play on or in the appliance. Close supervision of children is necessary when using the appliance.

4)Before the appliance is removed from service or discarded, remove the door to the drying compartment.

5)Do not reach into the appliance if the drum is moving.

6)Do not install or store this appliance where it will be exposed to the weather.

7)Do not tamper with controls.

8)Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions.

9)Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

10)Clean lint screen before or after each load.

11)Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

12)The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

13)Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

14)Do not use fabric softners or products to eliminate static unless recommended by the manufacturer of the fabric softner or product.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING - Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

!WHAT TO DO IF YOU SMELL GAS:

???Do not try to light a match or cigarette, or turn on any gas or electrical appliance.

???Do not touch any electrical switches. Do not use any phone in your building.

???Clear the room, building or area of all occupants.

???Immediately call your gas supplier from a neighbor???s phone. Follow the gas supplier???s instructions carefully.

???If you cannot reach your gas supplier, call the fire department.

!WARNING

To reduce the risk of fire or explosion, electric shock, property damage, personal injury or death when using this appliance, please follow all instructions and information, including those in this manual and instructions and information provided by your gas supplier, including the following:

???Do not store or use any gasoline, dry-cleaning solvents any other flammable vapors or liquids in the area surrounding this appliance.

???Do not dry anything that has ever had anything flammable on it, even after washing.

???No washer can completely remove oil. Do not dry any articles that have ever had any kind of oil on them, including cooking oil.

???Articles containing foam, rubber, rubber-like materials, plastic or similar materials should be dried on a clothesline or by using an air cycle.

???Failure to follow these instructions can result in fire, death or serious injury.

???A qualified service person or company must perform installation and service of this appliance.

!WARNING!

???Keep flammable materials and vapors, such as gasoline, away from dryer.

???Place dryer at least 18 inches above the floor for a garage installation.

???Failure to do so can result in death, explosion or fire.

California safe drinking water and toxic enforcement act

This act requires the governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

STEP 1 Positioning the Dryer.

Choose a location with a solid floor for your dryer. Place the dryer at least eighteen inches above the floor for a garage installation. After placing the dryer in the desired location, please confirm that the dryer has the required clearances through reference to the following information and manual sections on Exhaust Requirements and Maintenance.

If you are installing your dryer in a manufactured or mobile home, please refer to STEP 9 below for additional instructions.

48.4???

Certain minimum clearance are required above,behind, and to the sides of the dryer in the ever you install it any closer of other recessed area. Those required minimum clearances are set forth in the picture below. Please also keep the following instructions in mind when installing in a closet or recessed area:

???Consider allowing additional clearance for installation and servicing.

???Wall,door and flow molding may require additional clearance.

???Additional space of 1inch (2.5cm) is recommended an all sides in order to reduce noise transfer.

???Consider space needed for companion appliances.

???For closer installation, the picture below shows the minimum required ventilation openings for the door. A louvered door with comparable ventilation openings are also acceptable.

(123 cm)

38.7??? (98.3 cm)

*Most installations require a minimum 5 1/2 in.

(14 cm) clearance behind the dryer for the exhaust vent with elbow.

<Closet door>

STEP 2 Procedure for Reversing the Door

The door on your dryer can be installed to open either to the left or the right. Follow these procedures to reverse the direction in which your door opens:

2

3

STEP 3 Connecting the Exhaust

and Venting System.

In addition to the following warnings, please refer to manual section on Exhaust Requirements and Maintenance. IMPORTANT: To reduce the risk of fire, combustion, and gas accumulation, the dryer must be vented to the outdoors. Please follow the instructions (and all others in this manual) very carefully.

???Do not use thin plastic or foil ducting.

???Use 4" (10.2 cm) diameter rigid or flexible metal duct (note: venting materials are not supplied with the dryer, and you should obtain the venting materials necessary for proper installation)

???Position the dryer where the exhaust duct is shorter as possible

???Clean old ducts before installing this dryer

???The male end of each section of exhaust duct must point away from the dryer

???Use fewer elbow joints as possible

???Use duct tape on all duct joints

???Insulate ductwork that runs through unheated areas in order to reduce condensation and lint build-up on pipe walls; and

???PLEASE BE AWARE THAT FAILURE TO

EXHAUST THE DRYER CORRECTLY WILL

VOID THE DRYER???S WARRANTY.

!WARNING!

???Use a heavy metal vent.

???Do not use a plastic vent.

???Do not use a metal foil vent.

???Failure to follow these instructions can result in death or fire.

???Clean old ducts before installing this dryer

???ALTERNATE EXHAUST DIRECTIONS

1.Remove a screw and exhaust duct.

2-1. Detach and remove a knockout at the button, left or right side as desired. (Right Side Vent not available on Gas dryer)

, , the order of work.

2-2. Reconnect the another duct[11 in(28cm)] to the blower housing, and attach the duct to the base. (Duct is a SVC part)

3-1. Pre-assemble 4" elbow with 4" duct. Wrap duct tape around joint.

3-2. Insert elbow duct assembly first through the side opening and connect the elbow to the internal duct.

FOR

STEP 4 Connection of Gas Supply

(Gas dryer only). In addition to the following, please refer to manual section on Gas Requirements and Instructions.

1

2

5

3 4

1.New stainless steel flexible connector. Use this type of connector only if allowed by local codes. Use Design AGA Certified Connector.

2.1/8" NPT Pipe Plug (for checking inlet gas pressure)

3.Equipment Shut-Off Valve- Installed within 6??? (1.8 m) of dryer

4.Iron Pipe. Shorter than 20??? (6.1 m)

Use 3/8" pipe. Longer than 20??? (6.1 m) - Use 1/2" pipe.

5.3/8" N.P.T. Gas Connection

1.Confirm that the type of gas available in your laundry room is appropriate for the dryer. The dryer is prepared for Natural Gas with a 3/8"

NPT gas connection.

2.Remove the shipping cap from the gas connection at the back of the dryer. Make sure that you don???t damage the threads of the gas connection pipe when you remove the shipping cap.

3.Connect the dryer to your laundry room???s gas supply using a new flexible stainless steel connector (as noted below, only use a new stainless steel flexible connector if allowed by your local codes).

4.Securely tighten all connections between the dryer and your laundry room???s gas supply. Turn on your laundry room???s gas supply and check all pipe connections (both internal and external) for gas leaks with a non-corrosive leak detection fluid.

5.For LP (Liquefied Petroleum) gas connection, refer to this manual???s section entitled Gas Requirements and Instructions.

STEP 5 Electrical Plug Connections

for Electric Dryer Only.

Following are several warnings and instructions concerning making the electrical connection for electric dryers. More detailed information concerning the electrical connection is provided at the manual section entitled Electrical Requirements For Electric Dryer and it is important that you thoroughly review that section, and the remainder of this manual, before taking any steps to install or use this dryer.

1.Use only a new U.L. listed No. 10 (copper wire only) three conductor power supply cord kit rated 240 Volts (minimum) 30 Amperes and labeled as suitable for use in a clothes dryer.

2.Four-wire cord is required for manufactured (mobile) home installations and use and where local codes do not allow grounding of this appliance through neutral.

3.The wiring diagram is provided inside the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer.

4.For additional instruction on connecting the dryer to an electrical power source, please refer to this manual???s section on Electrical Requirements and Electric Dryer.

!WARNING!

???Use a new UL approved 30 amp power supply cord or 10 gauge solid copper wire.

???Use a UL approved strain relief.

???Disconnect power before making electrical connections.

???Connect neutral wire(white or center wire) to center terminal.

???Ground wire(green or bare wire) must be connected to green ground connector.

???Securely tighten all electrical connections

???See installation instructions for complete instructions.

???Failure to do so can result in fire or electrical shock.

FOR

STEP 6 Preparation of the Dryer.

Prior to the first use of this appliance, use all- purpose cleaning products or a solution of detergent

STEP 7 Confirming Heat Source

Operation.

Confirming Heat Source in Gas Dryers

Close the door to the dryer drum/drying compartment and, after completing all steps in this manual for proper installation of this dryer, start the dryer on a heat setting, as described more fully in the operating instructions that accompany the dryer. After the dryer starts, the igniter will glow red and the main burner will ignite.

Warning: If all air is not purged from the gas line, the gas igniter may go off before the gas and the main burner have ignited. If this happens, the igniter will re-attempt gas ignition after approximately two minutes.

Confirming Heat Source in Electric Dryers

Close the door to the dryer drum/drying compartment and, after completing all steps in this manual for proper installation of this dryer, start the dryer on a heat setting, as described more fully in the operating instructions that accompany the dryer. The exhaust air or the exhaust pipe should be warm after the dryer has been operating for three minutes.

STEP 8 Dryer Airflow.

Effective dryer operation requires appropriate dryer airflow. The adequacy of the airflow can be measured by evaluating the static pressure. Static pressure in the exhaust duct can be measured with a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer. Static pressure in the exhaust duct should not exceed 0.6 inches (1.5 cm). The dryer should be checked with the dryer running with no load.

Measuring Static pressure

Manometer

Exhaust Duct

MAXIMUM STATIC

PRESSURE IN

WATER COLUMN

0.6 inche (1.5 cm)

1 1

STEP 9 Additional Instructions for Installation of Your Dryer in a Manufactured or Mobile Home.

The following instructions are applicable to installations of the dryer in a manufactured or mobile home. Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/CSA0Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.

The following instructions apply to any installation of the dryer in a manufactured or mobile home:

1)The gas dryer must be permanently attached to the floor.

2)The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided at the manual section entitled Electrical Requirements for Electric Dryer

3)To reduce the risk of combustion and fire, the dryer must be vented to the outside.

4)Electric dryers may be vented to the outside using the back, left, right, or bottom panel.

5)Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryer may not be vented to the outside using the right side panel because of the burner housing.

6)The dryer exhaust duct must be affixed securely to the manufactured or mobile home structure, and the exhaust duct must be made of a material that will resist fire and combustion, and it is recommended that you use a rigid or flexible metal pipe.

7)DO NOT connect the exhaust duct with any other duct, vent, chimney, or other exhaust duct.

8)Make sure the dryer has adequate access to outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 in2 (163 cm2).

9)It is important that the clearance of the duct from any combustible construction be at least 2 inches (5 cm), and, when venting the dryer to the outdoors, the dryer can be installed with a clearances of 1 inch at the sides and back of the dryer.

10)Please be aware that venting materials are not supplied with the dryer. You should obtain the venting materials necessary for proper installation.

! WARNING!

DO NOT connect exhaust ducts with metal screws or fasteners that extend into the duct.

! WARNING!

DO NOT vent the exhaust duct under the manufactured or mobile home.

To ensure safe and secure installation, please observe the instructions below.

WARNING

Do not attempt installation with one person.

Incorrect installation procedure can cause serious accidents and physical Injuries.

The weight of the dryer and the height of installation makes the stacking procedure too risky for one person. This procedure should be performed by 2 or more experienced service personnel.

4 Secure stacking kit side bracket to the washer with a screw on the back of bracket. Repeat Steps 2, 3, 4 for the other side.

5 Place the dryer on top of the washer by fitting legs as shown in the picture. Avoid finger injuries - be careful not to pinch fingers between the washer and dryer. Slide washer slowly backwards to the stopper of kit.

1 Place washer firmly on a stable, even and solid floor as product installation instructions describes in owner???s manual.

2 Peel protective paper off the tape from the stacking kit side bracket.

3 Fit the stacking kit side bracket firmly to the side of top plate by attaching the double- faced tape to top plate as picture shows.

6 Insert the front stacking kit. Push the front stacking kit back to the stoppers of side stacking kit.

7 Screw both sides of the front kit.

???Do not use stacking kit with a gas dryer in potentially unstable conditions like a mobile home.

1 3

Instructions for Grounding of your Electric Electric Dryer:

a)Please note that the wiring diagram is provided inside the dryer control hood.

b)This dryer must be connected to a grounded metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

c)The dryer has its own terminal block that must be connected to a separate branch, 60 Hertz, single phase circuit, AC (alternating current) circuit, fused at 30 Amperes (the circuit must be fused on both sides of the line). ELECTRICAL

SERVICE FOR THE DRYER SHOULD BE

OF MAXIMUM RATE VOLTAGE LISTED

ON THE NAMEPLATE. DO NOT CONNECT DRYER TO 110, 115, OR 120 VOLT CIRCUIT. Heating elements are available for field installation in dryers which are to be connected to electrical service of different voltage than that listed on nameplate.

d)If branch circuit to dryer is fifteen feet (4.50 m) or less in length, use U.L. (Underwriters Laboratories) listed No. 10 A.W.G. wire (copper wire only), or as required by local codes. If over fifteen feet (4.50 m), use U.L. (Underwriters Laboratories) listed No. 8 A.W.G. wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so dryer can be moved from its normal location when necessary.

e)The power cord (pigtail) connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions mentioned on the following pages.

f)The method of wiring the dryer is optional and subject to local code requirements. Refer to examples on next page.

g)You must select the method by which to wire your dryer according to local code and ordinance requirements. Sample methods are included in the following pages.

! WARNING!

Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer.

4-wire receptacle (NEMA type14-30R)

Use the instructions at this section if your home has a 4-wire receptacle (NEMA type 14-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord.

3-wire receptacle (NEMA type10-30R)

Use the instructions at this section if your home has a 3-wire receptacle (NEMA type 10-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord.

4-wire connection : Direct wire

Important : use 4-wire connection in the places such as mobile homes and areas where 3-wire connections is not available.

Prepare minimum 5ft(1.52m) of length in order for dryer to be replaced.

First, peel 5 inch (12.7cm) of covering material from end. Make a 5 inch of ground wire bared. After cutting 11/2 inch (3.8cm) from 3 other wires. peel insulation back 1inch (2.5cm). Make ends of 3 wires a hook shape.

Then, put the hooked shape end of the wire under the screw of the terminal block(hooked end facing rightward) and pinch the hook together and screw tightly.

4-wire direct

If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box

3-wire direct

If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box

1.Connect neutral wire(white) of power cord to center terminal block screw.

2.Connect red and black wire to the left and right terminal block screws.

3.Connect ground wire(green) of power cord to external ground screw and move neutral ground wire of appliance and connect it to center screw.

4.Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on tight and power cord is in right position.

3-wire connection : Direct wire

Important : use 3-wire connection in the places such as mobile homes and areas where 3-wire connections is not available.

Prepare minimum 5ft(1.52m) of length in order for dryer to be replaced.

First, peel 3 1/2 inch (8.9cm) of covering material from end and bare 1 inch from the ends.

Then, put the hooked shape end of the wire under the screw of the terminal block(hooked end facing rightward) and pinch the hook together and screw tightly.

1.Connect neutral wire(white) of power cord to center terminal block screw.

2.Connect red and black wire to the left and right terminal block screws.

3.Make sure that the strain relief screw is tightened and be sure that all terminal block nuts are on tight and power cord is in right position.

Option 1: 4-wire connection with a Power supply cord.

???lf your local codes or ordinances do not allow the use of a 3 wire connection, or you are installing your dryer in a mobile home, you must use a 4- wire connection.

1.Connect neutral wire(white) of power cord to center terminal block screw.

2.Connect red and black wire to the left and right terminal block screws.

3.Connect ground wire(green) of power cord to external ground screw and move neutral ground wire of appliance and connect it to center screw.

4.Make sure that the strain relief screw is tightened. and be sure that all terminal block nuts are on tight and power cord is in right position.

Option 2: 3-Wire Connection with a Power Supply Cord

lf your local codes or ordinances permit the connection of a frame-grounding conductor to the neutral wire, use these instructions. If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under Section 3: Optional 3-wire connection.

Option 3: Optional 3-wire

connection.

???If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under this section.

1.Connect neutral wire(white) of power cord to center terminal block screw.

2.Connect ground wire of appliance and neutral wire of power cord to center terminal block screw.

3.Connect red and black wire to the left and right terminal block screws.

4.Make sure that the strain relief screw is tightened. and be sure that all terminal block nuts are on tight and power cord is in right position.

5.Connect a independent ground wire from external ground connector to proper ground.

a)Please note that the wiring diagram is provided inside the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer.

b)Your dryer is designed to be used on a separate branch, polarized, three-wire, effectively grounded, 120 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 Ampere fuse, equivalent fusetron or circuit breaker.

c)Use separately fused circuits for washers and dryers, and DO NOT operate a washer and a dryer on the same circuit.

! WARNING!

Do not overload the circuit by operating other appliances on the same circuit when this appliance is operating, by using an extension cord to connect the dryer to the power source, or by using any adapter to allow additional cords to connect to the same outlet.

! WARNING!

DO NOT modify the plug provided with the dryer. If it does not fit the outlet in your laundry room, a proper outlet will need to be installed in your laundry room by a qualified service person or company.

STANDARD 120 VOLT, 60 HERTZ, 3-WIRE

EFFECTIVELY GROUNDED CIRCUIT

1L1

2Ground

3Neutral Side

4Round Grounding Prong

5Neutral

a)The dryer has a three-prong plug to help guard against shock. The plug should be plugged directed into a properly grounded three-prong receptacle that is rated 120 Volts AC (alternating current) 15 Amps. This plug, in order to be properly and fully effective, must be plugged into a properly installed outlet that is grounded in accordance with all local codes and ordinances.

b)The dryer must be grounded in order to reduce the risk of electric shock, including a malfunction or breakdown.

c)If your laundry room does not meet the specifications required by this manual, or if you are uncertain whether or not your laundry room meets these specifications, please have a qualified service person or company, for example a qualified electrician or your local electric company, review your laundry room???s electrical

1.Gas supply requirements: Liquefied Petroleum (L.P.) Gas (2,500 Btu/ft3 (93.1 MJ/m3)) service must be provided at 10 + 1.5 in. water column pressure.

2.Important: DO NOT connect the dryer to the Liquefied Petroleum (LP) Gas service without converting the gas value.

3.A qualified technician must perform the LP Gas conversion. Contact your local gas service branch if you require additional assistance or information.

4.Isolate the dryer from the gas supply piping system by closing its individual manual shut-off valve, during any pressure testing of the gas supply system at test pressure equal to or less than 2/1 psi (3.45 kPa).

5.Supply Line Requirements. Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 feet (1.8m) of the dryer, in accordance with the National Fuel Gas Code ANSI Z223.1. A 1/8 in. N.P.T. pipe plug must be installed as shown.

6.If using a rigid pipe, the rigid pipe should be 1/2 inch IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8 inch approved tubing may be used where lengths are less than 20 feet (6.1m). Larger tubing should be used for lengths in excess of 20 feet (6.1m). It is also important that you use pipe joint compound that is insoluble in LP gas.

7.To reduce the danger of gas leaks, explosion, and fire, please follow and observe the following instructions and WARNINGS:

???Connect the dryer to the type of gas shown on the nameplate;

???Use new flexible stainless steel connectors;

???Use Teflon tape and pipe joint compound insoluble in LP gas on all pipe threads;

???Purge gas supply of air and sediment before connecting the gas supply to the dryer; in order to prevent gas valve contamination, before tightening connection between gas supply and dryer, purge remaining air until odor of gas is identified; and

???DO NOT use an open flame to inspect for gas leaks; instead, use a non-corrosive leak detection fluid.

! WARNING!

DO NOT attempt any disassembly of the dryer, any disassembly requires the attention and tools of an authorized and qualified service person or company.

!WARNING!

???Use a new AGA or CSA approved gas supply line.

???Install a shut-off valve.

???Securely tighten all gas connections.

???If connected to LP, have a qualified person make sure gas pressure does not exceed 13 in. water column.

???Examples of a qualified person include licensed heating personnel, authorized gas company personnel, and authorized service personnel.

???Failure to do so can result in death, explosion, or fire.

Exhaust Requirements and Instructions:

1.Venting materials are not provided with the dryer and you should obtain the necessary venting materials locally. For example, the outer end of exhaust pipe must have a weather hood with hinged dampers to prevent back-draft when the dryer is not in use.

2.The exhaust duct must be four inches (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer.

3.Rigid metal duct is recommended. Do not install flexible duct in concealed spaces. Non-combustible flexible metal duct is acceptable. Do not use plastic or thin foil ducting.

4.DO NOT use sheet metal screws on exhaust pipe joints or other fastening means which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape.

5.To maximize operating results, please observe the duct length limitations noted in the chart above.

Exhaust and Dryer Maintenance

! WARNING!

Disconnect the dryer???s electric power prior to any cleaning or maintenance.

1.After one year of use, the interior and complete exhaust system of the dryer should be examined and cleaned if necessary.

2.You should inspect and clean the exhaust duct at least yearly.

3.Check the weather hoods frequently to ensure the dampers are moving freely, that the dampers are not pushed in and that nothing has been set against the dampers.

4.A qualified service person or company should be used to perform this maintenance.

5.A Flexible Metal Vent Kit, available at extra cost, can be used to exhaust the dryer when it is placed in hard to reach places. This Kit comes in two pieces, one of which is attached to the dryer and the other is attached to the wall exhaust outlet. Following attachment of the two separate pieces to the dryer and the wall, the dryer may be returned to its final position, after which the two pieces themselves can be connected.

7.Ordinarily, the dryer drum will need no care. Wipe the exterior of the dryer as required, and always immediately wipe the exterior of the dryer in the event any detergent, bleach, or other washing products is spilled on the dryer, because these products may cause permanent damage to the exterior finish of the dryer.

8.Clean the control panel with a damp cloth as necessary. Warning: spray pre-wash products may damage the finish of the control panel.

9.Please clean the lint filter either before drying each load or after drying each load.

10.Always make sure the lint filter is clean before starting a new load, because a clogged lint filter may increase drying times.

11.Annually remove the lint filter and attach it to the vacuum duct. See item #2 above.

12.Please note that the wiring diagram is provided inside the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer.

Cleaning the Lint Screen

1.Clean the lint filter either before drying each load or after drying each load. Always make sure the lint filter is clean before starting a new load, because a clogged lint filter may increase drying times.

2.To clean, pull the lint screen straight up and roll any lint off the screen with your fingers. Do not rinse or wash screen to remove lint, because wet lint is hard to remove. Push the lint screen firmly back into place.

3.Always ensure the lint screen is firmly secured before running the dryer. Running the dryer with a loose lint screen may cause overheating and damage to the dryer and articles being dried.

4.Some articles may shed more lint than other towels (for example, towels made of synthetic fibers and natural fibers), causing the lint screen to become congested more quickly. Remove lint from the lint screen before and after drying these articles, such as new towels.

5.In the event lint falls off of the lint screen and into the dryer during removal, inspect the exhaust hood and remove any lint.

6.Laundry detergent and fabric softener residue can build up on the lint screen, causing longer drying times. The screen is likely blocked if lint falls off the screen. In order to prevent this type of build up, and help ensure proper operation of your dryer, clean the lint screen with a nylon brush every six months or, if necessary, more frequently. The lint filter can also be washed as follows:

a)After rolling the lint off of the screen with your fingers, wet both sides of the screen with hot or warm water.

b)Wet a nylon brush with hot water and liquid detergent and scrub the lint screen with the brush to remove the buildup of detergent and fabric softener.

c)Repeat as necessary.

d)After the residue has been removed, rinse screen with hot water.

e)After drying the lint screen with a clean towel, firmly replace the lint screen in your dryer.

STER

1. Using Your Dryer

1.Clean lint screen before or after each cycle.

2.Place laundry into dryer and close door. See Loading.

3.Turn the knob to select the drying cycle you want. The preset settings for Sensor Dry Cycles or Manual Cycles will glow. The estimated or actual cycle time (in minutes) will show in the display.

! WARNING!

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Do not dry anything that has ever had anything flammable on it (even after washing). Failure to follow these instructions can result in death, explosion, or fire.

! WARNING!

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on it (including cooking oils).

Items containing foam, rubber, or plastic must be dried on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death or fire.

2. To use a Sensor Dry Cycle

3. To use a Manual Dry Cycle

???Select a Manual Dry Cycle.

???Press MORE TIME or LESS TIME until the desired drying time is displayed. Tap MORE TIME or LESS TIME and the time will change by

1 minute intervals.

NOTE: The MORE TIME or LESS TIME feature can be used with Manual Dry, Time Dry, and Rack Dry Cycles.

??? Press TEMP. CONTROL until the desired temperature indicator glows.

??? (OPTIONAL STEP) If desired, select OPTIONS. For more details, see Options.

???Press START/PAUSE. Be sure the door is closed.

???If you do not press START/PAUSE within 10 minutes of selecting the cycle, the dryer automatically shuts off.

???If you wish to end your drying cycle after pressing START/PAUSE, press START/PAUSE again.

4. Stopping Your Dryer

To stop your dryer at any time

Press START/PAUSE or open the door.

Pausing or Restarting

To pause the dryer at any time

Open the door or press START/PAUSE once.

To restart the dryer

5. Loading

When loading your dryer my to:

???Determine load size by the amount of space the load requires rather than the weight of the load.

???Avoid overloading the dryer.

Following these instruction can help reduce your utility bill, prolong the life of your clothes, and decrease the likelihood of uneven drying and wrinkle.

Following are sample loads for Super Capacity Dryers:

Child Lock

This feature allows you to lock your settings to prevent children from changing them. You can also use the child lock feature

to prevent unintended or option changes during dryer

6. Cycle Descriptions

Select the drying cycle that matches the type of load you are drying.

(See Sensor Dry or Manual Preset Cycle Settings charts.)

Sensor Dry Cycles allow you to match the cycle to the load you are drying. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying

Sensor Dry Cycle

???Cotton/Towels

Use for drying denims, towels, heavy cottons (medium-high heat)

???Normal

Use for drying sturdy fabrics such as work casual clothes (medium heat)

???Delicates

Use for drying synthetic fabrics, washable knit fabrics, and no-iron finishes (low heat)

Sensor Dry Preset Cycle Settings

*Estimated Time with SENSOR DRY LEVEL (Normal) setting.

Manual Cycles

Use Manual Cycles to select a specific amount of drying time and a drying temperature. When a Manual Cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing MORE TIME or LESS TIME.

???Speed Dry

Use for small loads or loads that need a short drying time.

???Air Dry

Use the Air Dry Modifier for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics.

???Time Dry

Use this cycle to complete drying if items are still damp after an Sensor Dry Cycle. Time dry is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.

Manual Preset Cycle Settings

7. Options

You can customize your cycles by selecting options.

WRINKLE CARE

When you select the wrinkle free option, the dryer will periodically tumble for up to three hours after to the cycle has completed.

This option helps to prevent the wrinkle that form when a load remains in the dryer after the cycle is completed. The wrinkle care option ends after the three hours when you push the wrinkle care option button on, when you open the dryer door

8. Modifiers

Use Modifiers to select temperatures for the Manual Cycles. Press TEMP. CONTROL until the desired temperature setting glows. Temperature modifiers cannot be used with the Sensor Dry Cycles.

When using Air Dr y

This chart shows examples of items that can be dried using AIR DRY.

shear nylon

* Reset cycle to complete drying, if needed.

???Check to see that coverings are securely stitched.

???Shake and fluff pillows by hand periodically during the cycle.

???Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Air Dry is not available with Sensor Dry Cycles.

9. Rack Dry

The dryer rack is shipped in place in your dryer. Remove and discard any packing material before use.

The RACK DRY is designed for use with items that you do not want to tumble dry, including sweaters and similar items. The heated dryer rack allows the heated air inside the dryer to flow in a concentrated pattern, allowing effective and consistent drying. Use RACK DRY to select the desired time.

To use the RACK DRY

???When drying washable wool items, block and shape the items to lay flat on the dryer rack.

2. Put the dryer rack into the drum

NOTE: Check the lint screen and remove any lint accumulated from items dried on the rack.

*Reset time as needed to complete drying.

???Select MORE TIME or LESS TIME. Reset time as needed to complete drying. Refer to the following table.

3. Make sure that dryer is evenly placed right onto the drum inside and door rim.

The BEEPER controls the volume of the beep that is made when you press any of the buttons on the control panel and the termination of any cycle is indicated.

Press BEEPER to adjust the sound level or turn off the signal.

??? Clean the door and its opening

1. Wipe out the door opening. Otherwise, build- ups of dirts and foreign objects will damage sealing of door.

2. Clean the transparent glass door to keep inside view clear througth the glass.

1.Open the door and pull the filter straight up

2.Clean the filter using one of following ways in cases.

Run the fingers across the filter

Vaccum the lint filter

Wash the lint screen in warm,soapy water.

Dry thoroughly and replace.