Separate purchase

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or regis- tered trademarks of HDMI Licensing LLC.

Optional extras can be changed or modified for quality improvement without any notification.

Contact your dealer for buying these items.

This device only works with compatible LG LED LCD TV or LCD TV.

Wireless Media Box

(32/42/46/52/60LD5***,

32LE3***, 32/37/42LE4***,

32/37/42/47/55LE5***)

WATCHING TV / PROGRAMME CON-

TROL

CONTENTS

I

CONTENTS

-Stereo/Dual Reception (In Analogue Mode Only) 117

-NICAM Reception (In Analogue Mode Only)118

TIME SETTING

PREPARATION

LCD TV MODELS : 19/22/26/32LD35**, 19/22/26/32LD34**

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.

??? Image shown may differ from your TV.

This item is not included for all models.

PREPARATION

Owner???s Manual Batteries Remote Control

(AAA)

Polishing Cloth

Polishing cloth for use on the screen.

* Lightly wipe any stains or fingerprints on the surface of the TV with the polish- ing cloth.

Do not use excessive force. This may cause scratching or discoloura- tion.

PREPARATION

FRONT PANEL CONTROLS

NOTE

???TV can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption.

???The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost.

CAUTION

???Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments of glass, or the TV may fall.

???Do not drag the TV. The floor or the product may be damaged.

???Image shown may differ from your TV.

Only 19/22LD35**, 19/22LD34**

POWER MENU VOLUME

SPEAKER

Remote Control Sensor

Power/Standby Indicator

???Illuminates red in standby mode.

???Illuminates blue when the TV is switched on.

A-2

Only 26/32LD35**, 26/32LD34**

PROGRAMME

VOLUME

OK

MENU

INPUT

POWER

BACK PANEL INFORMATION

Only 19/22LD35**, 19/22LD34**

??? Image shown may differ from your TV.

11

1

12

PREPARATION

1Power Cord Socket

This TV operates on an AC power. The volt- age is indicated on the Specifications page. (??? p.137 to 147) Never attempt to operate the TV on DC power.

2HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

3OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

4RGB/DVI Audio Input

Connect the audio from a PC or DTV.

5Audio/Video Input

Connect audio/video output from an external device to these jacks.

6Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

7Component Input

Connect a component video/audio device to these jacks.

8RGB IN Input

Connect the output from a PC.

9RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

10Antenna Input

Connect antenna or cable to this jack.

11USB Input

Connect USB storage device to this jack.

12PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

13Headphone Socket

Plug the headphone into the headphone socket.

PREPARATION

Only 26LD35**, 26LD34**

??? Image shown may differ from your TV.

7 8

1Power Cord Socket

This TV operates on an AC power. The volt- age is indicated on the Specifications page. (??? p.137 to 147) Never attempt to operate the TV on DC power.

2HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

3OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

4RGB/DVI Audio Input

Connect the audio from a PC or DTV.

5Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

6Component Input

Connect a component video/audio device to these jacks.

A-4

10

11

2

12

13

9

7RGB IN Input

Connect the output from a PC.

8RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

9Antenna Input

Connect antenna or cable to this jack.

10USB Input

Connect USB storage device to this jack.

11PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

12Headphone Socket

Plug the headphone into the headphone socket.

13Audio/Video Input

Connect audio/video output from an external device to these jacks.

Only 32LD35**, 32LD34**

??? Image shown may differ from your TV.

10

11

1

2

12

13

PREPARATION

1Power Cord Socket

This TV operates on an AC power. The volt- age is indicated on the Specifications page. (??? p.137 to 147) Never attempt to operate the TV on DC power.

2HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

3OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

4RGB/DVI Audio Input

Connect the audio from a PC or DTV.

5Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

6Component Input

Connect a component video/audio device to these jacks.

7RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

8RGB IN Input

Connect the output from a PC.

9Antenna Input

Connect antenna or cable to this jack.

10USB Input

Connect USB storage device to this jack.

11PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

12Headphone Socket

Plug the headphone into the headphone socket.

13Audio/Video Input

Connect audio/video output from an external device to these jacks.

PREPARATION

Only 19/22LD35**, 19/22LD34**

screen from damage.

Only 26/32LD35**, 26/32LD34**

screen from damage.

NOT USING THE DESK-TYPE STAND

??? Image shown may differ from your TV.

When installing the wall-mounted unit, use the protection cover.

3 Detach the stand from TV.

the protection cover, adhere it to the TV as shown.

Protection Cover

PREPARATION

A-7

PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

??? Image shown may differ from your TV.

SWIVEL STAND

(Except for 19/22LD35**, 19/22LD34**)

??? Image shown may differ from your TV.

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

POSITIONING YOUR DISPLAY

(Only 19/22LD35**, 19/22LD34**)

???Image shown may differ from your TV.

???Adjust the position of the panel in various ways for maximum comfort.

??? Tilt range

ATTACHING THE TV TO A

DESK (Only 26/32LD35**, 26/32LD34**)

??? Image shown may differ from your TV.

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.

PREPARATION

1-Screw (provided as parts of the product)

Stand

Desk

WARNING

???To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.

A-9

PREPARATION

KENSINGTON SECURITY

SYSTEM

??? This feature is not available for all models. ??? Image shown may differ from your TV.

NOTE

???The Kensington Security System is an optional accessory.

???If the TV feels cold to the touch, there may be a small ???flicker??? when it is turned on.

This is normal, there is nothing wrong with TV.

???Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

???Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distor- tion effects on the screen.

A-10

CAREFUL INSTALLATION

ADVICE

???You should purchase necessary components to fix the TV safety and secure to the wall on the market.

???Position the TV close to the wall to avoid the possibility of it falling when pushed.

???The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoid- ing the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.

11

22

1 Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture.

(If your TV has bolts in the eyebolts, loosen then bolts.)

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

2 Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.

3

3 Use a sturdy rope to tie the product for align- ment. It is safer to tie the rope so it becomes horizontal between the wall and the product.

NOTE

???When moving the TV undo the cords first.

???Use a platform or cabinet strong and large enough to support the size and weight of the TV.

???To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

???The TV can be installed in various ways such as on a wall, or on a desktop etc.

???The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to earth the TV by connecting it to tele- phone wires, lightening rods or gas pipes.

Power

Supply

Circuit breaker

DESKTOP PEDESTAL

INSTALLATION

??? Image shown may differ from your TV.

For adequate ventilation allow a clearance of 10 cm all around the TV.

10 cm

10 cm

NOTE

???Should Install wall mount on a solid wall per- pendicular to the floor.

???Should use a special wall mount, if you want to install it to ceiling or slanted wall.

???The surface that wall mount is to be mount- ed on should be of sufficient strength to sup- port the weight of TV set; e.g. concrete, nat- ural rock, brick and hollow block.

???Installing screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount.

???LG is not liable for any accidents or damage to property or TV due to incorrect installa- tion:

-Where a non-compliant VESA wall mount is used.

-Incorrect fastening of screws to surface which may cause TV to fall and cause per- sonal injury.

-Not following the recommended Installation method.

10 cm

10 cm

10 cm

PREPARATION

PREPARATION

1

(POWER) Switches the TV on from standby or off to standby.

ENERGY Adjust the Energy Saving mode of the TV.(???p.95)

SAVING

AV MODE It helps you select and set images and sounds when connecting AV devices.(???p.50)

INPUT External input mode rotate in regular sequence.(???

p.43)

TV/RAD Selects Radio, TV and DTV channel.

0 to 9 number Selects a programme.

button Selects numbered items in a menu.

LIST Displays the programme table. (???p.41)

Q.VIEW Returns to the previously viewed programme.

MENU Selects a menu.

Clears all on-screen displays and returns to TV viewing from any menu.(???p.19)

GUIDE Shows programme guide.(???p.86)

Q. MENU Select the desired quick menu source. (Aspect Ratio, Clear Voice II , Picture Mode, Sound Mode, Audio (or Audio Language), Sleep Timer, Skip Off/ On, USB Device).(??? p.18)

BACK Allows the user to move return one step in an inter- active application, EPG or other user interaction function.

EXIT Clears all on-screen displays and returns to TV viewing from any menu.

INFO i Shows the present screen information.

THUMBSTICK Allows you to navigate the on-screen menus and (Up/Down/Left/Right) adjust the system settings to your preference.

OK Accepts your selection or displays the current mode.

Coloured These buttons are used for teletext (on TELETEXT buttons models only), Programme edit.

1 TELETEXT These buttons are used for teletext. BUTTONS For further details, see the ???Teletext??? section.(???

p.130)

SUBTITLE Recalls your preferred subtitle in digital mode.

VOLUME UP Adjusts the volume. /DOWN

FAV Displays the selected favourite programme.

MARK Select the input to apply the Picture Wizard settings.

Check and un-check programmes in the USB menu.

RATIO Selects your desired Aspect Ratio of picture. (???p.92)

MUTE Switches the sound on or off.

Programme Selects a programme.

UP/DOWN

PAGE UP/ Move from one full set of screen information to the DOWN next one.

SIMPLINK / Controls SIMPLINK or MY MEDIA menu(Photo List MY MEDIA Menu and Music List).

control buttons

See a list of AV devices connected to TV.

When you toggle this button, the Simplink menu appears at the screen.(???p.46)

PREPARATION

PREPARATION

LCD TV MODELS : 32/37/42/47LD4***, 26/32LD32**, 26/32LD33**

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.

??? Image shown may differ from your TV.

This item is not included for all models.

Polishing Cloth

Polishing cloth for use on the screen.

* Lightly wipe any stains or fingerprints on the surface of the TV with the polish- ing cloth.

Do not use excessive force. This may cause scratching or discoloura- tion.

Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord.

The closer the location of the ferrite core to the power plug, the better it is.

A-14

Install the power plug closely.

FRONT PANEL CONTROLS

NOTE

???TV can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption.

???The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost.

CAUTION

???Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments of glass, or the TV may fall.

???Do not drag the TV. The floor or the product may be damaged.

PREPARATION

PREPARATION

Only 26LD32**, 26LD33**

POWER MENU VOLUME

SPEAKER

Remote Control Sensor

Power/Standby Indicator Illuminates red in standby mode.

Illuminates blue when the TV is switched on.

Only 32/37/42/47LD42**, 32LD32**, 32LD33**

PROGRAMME

VOLUME

OK

MENU

INPUT

POWER

BACK PANEL INFORMATION

??? Image shown may differ from your TV.

10

1

11

1

2

12

13

PREPARATION

1Power Cord Socket

This TV operates on an AC power. The volt- age is indicated on the Specifications page. (??? p.137 to 147) Never attempt to operate the TV on DC power.

2HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

3OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

4RGB/DVI Audio Input

Connect the audio from a PC or DTV.

5Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

6Component Input

Connect a component video/audio device to these jacks.

7RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

8RGB IN Input

Connect the output from a PC.

9Antenna Input

Connect antenna or cable to this jack.

10USB Input

Connect USB storage device to this jack.

11PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

12Headphone Socket

Plug the headphone into the headphone socket.

13Audio/Video Input

Connect audio/video output from an external device to these jacks.

PREPARATION

Only 32/37/42/47LD45**

screen from damage.

Stand Body

Cover Base

3 Assemble the TV as shown.

Only 32/37/42/47LD42**, 26/32LD32**, 26/32LD33**

screen from damage.

2 Assemble the TV as shown.

BACK COVER FOR

WIRE ARRANGEMENT

???Image shown may differ from your TV.

1Connect the cables as necessary.

To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

2Open the Cable Management Clip as shown.

Cable Management Clip

3 Fit the Cable Management Clip as shown.

ATTACHING THE TV TO A

DESK

(Only 32/37/42LD4***, 26/32LD32**, 26/32LD33**)

??? Image shown may differ from your TV.

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.

1-Screw

(provided as parts of the product)

Stand

Desk

PREPARATION

NOTE

???Do not use the Cable Management Clip to lift the TV.

-If the TV is dropped, you may be injured or the TV may be damaged.

WARNING

???To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.

NOT USING THE

DESK-TYPE STAND

??? Image shown may differ from your TV. When installing the wall-mounted unit, use the protection cover.

Insert the Protection Cover into the TV until clicking sound.

Protection Cover

PREPARATION

NOTE

???The Kensington Security System is an optional accessory.

???If the TV feels cold to the touch, there may be a small ???flicker??? when it is turned on. This is normal, there is nothing wrong with TV.

???Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

???Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

A-20

CAREFUL INSTALLATION

ADVICE

???You should purchase necessary components to fix the TV safety and secure to the wall on the market.

???Position the TV close to the wall to avoid the possibility of it falling when pushed.

???The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoid- ing the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.

(If your TV has bolts in the eyebolts, loosen then bolts.)

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

that is mounted on the wall.

3

3 Use a sturdy rope to tie the product for align- ment. It is safer to tie the rope so it becomes horizontal between the wall and the product.

NOTE

???When moving the TV undo the cords first.

???Use a platform or cabinet strong and large enough to support the size and weight of the TV.

???To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

???The TV can be installed in various ways such as on a wall, or on a desktop etc.

???The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.

Power Supply

Circuit breaker

DESKTOP PEDESTAL

INSTALLATION

??? Image shown may differ from your TV.

For adequate ventilation allow a clearance of 10 cm all around the TV.

NOTE

???Should Install wall mount on a solid wall per- pendicular to the floor.

???Should use a special wall mount, if you want to install it to ceiling or slanted wall.

???The surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.

???Installing screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount.

???LG is not liable for any accidents or damage to property or TV due to incorrect installation:

-Where a non-compliant VESA wall mount is used.

-Incorrect fastening of screws to surface which may cause TV to fall and cause per- sonal injury.

-Not following the recommended Installation method.

10 cm

10 cm

10 cm

PREPARATION

WALL MOUNT: HORIZONTAL

INSTALLATION

???We recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall.

???We recommend that you purchase a wall mounting bracket which supports VESA stan- dard.

???LG recommends that wall mounting be per- formed by a qualified professional installer.

SWIVEL STAND

??? Image shown may differ from your TV.

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

A-21

PREPARATION

1

A-22

(POWER) Switches the TV on from standby or off to standby.

ENERGY Adjust the Energy Saving mode of the TV.(???p.95)

SAVING

AV MODE It helps you select and set images and sounds when connecting AV devices.(???p.50)

INPUT External input mode rotate in regular sequence.(???

p.43)

TV/RAD Selects Radio, TV and DTV channel.

0 to 9 number Selects a programme.

button Selects numbered items in a menu.

LIST Displays the programme table. (???p.41)

Q.VIEW Returns to the previously viewed programme.

MENU Selects a menu.

Clears all on-screen displays and returns to TV viewing from any menu.(???p.19)

GUIDE Shows programme guide.(???p.86)

Q. MENU Select the desired quick menu source. (Aspect Ratio, Clear Voice II , Picture Mode, Sound Mode, Audio (or Audio Language), Sleep Timer, Skip Off/ On, USB Device).(??? p.18)

BACK Allows the user to move return one step in an inter- active application, EPG or other user interaction function.

EXIT Clears all on-screen displays and returns to TV viewing from any menu.

INFO i Shows the present screen information.

THUMBSTICK Allows you to navigate the on-screen menus and (Up/Down/Left/Right) adjust the system settings to your preference.

OK Accepts your selection or displays the current mode.

Coloured These buttons are used for teletext (on TELETEXT buttons models only), Programme edit.

1 TELETEXT These buttons are used for teletext.

BUTTONS For further details, see the ???Teletext??? section.(??? p.130)

SUBTITLE Recalls your preferred subtitle in digital mode.

VOLUME UP Adjusts the volume. /DOWN

FAV Displays the selected favourite programme.

MARK Select the input to apply the Picture Wizard settings.

Check and un-check programmes in the USB menu.

RATIO Selects your desired Aspect Ratio of picture. (???p.92)

MUTE Switches the sound on or off.

Programme Selects a programme.

UP/DOWN

PAGE UP/ Move from one full set of screen information to the DOWN next one.

SIMPLINK / Controls SIMPLINK or MY MEDIA menu(Photo List MY MEDIA Menu and Music List).

control buttons

See a list of AV devices connected to TV.

When you toggle this button, the Simplink menu appears at the screen.(???p.46)

PREPARATION

PREPARATION

LCD TV MODELS : 32/42/46/52/60LD5***

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.

??? Image shown may differ from your TV.

This item is not included for all models.

Owner???s Manual

Power Cord

Ferrite Core

(This item is not included for all models.)

Polishing Cloth

Polishing cloth for use on the screen.

* Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth.

Do not use exces- sive force. This may cause scratching or discolouration.

FRONT PANEL CONTROLS

NOTE

???TV can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption.

???The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost.

CAUTION

???Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from frag- ments of glass, or the TV may fall.

???Do not drag the TV. The floor or the product may be damaged.

???Image shown may differ from your TV.

PREPARATION

SPEAKER

Power/Standby Indicator

???Illuminates red in standby mode.

???Illuminates blue when the TV is switched on.

PROGRAMME

VOLUME

OK

MENU

INPUT

POWER

Remote Control Sensor

Intelligent Sensor

Adjusts picture according to the surrounding conditions.

PREPARATION

BACK PANEL INFORMATION

??? Image shown may differ from your TV.

11

1

12

2

13

14

8 9

1Power Cord Socket

This TV operates on an AC power. The volt- age is indicated on the Specifications page. (??? p.137 to 147) Never attempt to operate the TV on DC power.

2HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

3RGB IN Input

Connect the output from a PC.

4OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

5RGB/DVI Audio Input

Connect the audio from a PC or DTV.

6Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

7Component Input

Connect a component video/audio device to these jacks.

A-26

10

8RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

9WIRELESS Control

Connect the Wireless Media Box to the

WIRELESS CONTROL jack on the TV.

10Antenna Input

Connect antenna or cable to this jack.

11USB Input

Connect USB storage device to this jack.

12PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

13Headphone Socket

Plug the headphone into the headphone socket.

14Audio/Video Input

Connect audio/video output from an external device to these jacks.

STAND INSTALLATION

??? Image shown may differ from your TV.

When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt.

screen from damage.

BACK COVER FOR

WIRE ARRANGEMENT

???Image shown may differ from your TV.

1Connect the cables as necessary.

To connect additional equipment, see the

External Equipment Setup section.

2 Open the Cable Management Clip as

shown.

PREPARATION

PREPARATION

ATTACHING THE TV TO A

DESK (Only 32/42LD5***)

??? Image shown may differ from your TV.

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.

1-Screw

(provided as parts of the product)

Stand

NOT USING THE

DESK-TYPE STAND

??? Image shown may differ from your TV. When installing the wall-mounted unit, use the protection cover.

Insert the Protection Cover into the TV until clicking sound.

Protection Cover

Desk

WARNING

???To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.

SWIVEL STAND

??? Image shown may differ from your TV.

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

KENSINGTON SECURITY

SYSTEM

???This feature is not available for all models.

???Image shown may differ from your TV.

The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.

For the detailed installation and use of the Kensington Security System, refer to the user???s guide provided with the Kensington Security System.

For further information, contact http://www.kens- ington.com, the internet homepage of the Kensington

company. Kensington sells security systems for expensive electronic equipment such as note- book PCs and LCD projectors.

NOTE

???The Kensington Security System is an optional accessory.

???If the TV feels cold to the touch, there may be a small ???flicker??? when it is turned on. This is normal, there is nothing wrong with TV.

???Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

???Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some tempo- rary distortion effects on the screen.

CAREFUL INSTALLATION

ADVICE

???You should purchase necessary components to fix the TV safety and secure to the wall on the market.

???Position the TV close to the wall to avoid the possibility of it falling when pushed.

???The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoid- ing the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.

11

2

22

1 Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the pic- ture.

(If your TV has bolts in the eyebolts, loosen then bolts.)

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

2 Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.

3

3 Use a sturdy rope to tie the product for align- ment. It is safer to tie the rope so it becomes horizontal between the wall and the product.

NOTE

???When moving the TV undo the cords first.

???Use a platform or cabinet strong and large enough to support the size and weight of the TV.

???To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

PREPARATION

A-29

PREPARATION

???The TV can be installed in various ways such as on a wall, or on a desktop etc.

???The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to earth the TV by connecting it to tele- phone wires, lightening rods or gas pipes.

Power

Supply

Circuit breaker

DESKTOP PEDESTAL

INSTALLATION

??? Image shown may differ from your TV.

For adequate ventilation allow a clearance of 10 cm all around the TV.

10 cm

10 cm

NOTE

???Should Install wall mount on a solid wall per- pendicular to the floor.

???Should use a special wall mount, if you want to install it to ceiling or slanted wall.

???The surface that wall mount is to be mount- ed on should be of sufficient strength to sup- port the weight of TV set; e.g. concrete, nat- ural rock, brick and hollow block.

???Installing screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount.

???LG is not liable for any accidents or damage to property or TV due to incorrect installa- tion:

-Where a non-compliant VESA wall mount is used.

-Incorrect fastening of screws to surface which may cause TV to fall and cause per- sonal injury.

-Not following the recommended Installation method.

10 cm

10 cm

10 cm

WALL MOUNT: HORIZONTAL

INSTALLATION

???We recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall.

???We recommend that you purchase a wall mounting bracket which supports VESA stan- dard.

???LG recommends that wall mounting be per- formed by a qualified professional installer.

REMOTE CONTROL KEY FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV.

PREPARATION

A-31

PREPARATION

A-32

VOLUME UP Adjusts the volume. /DOWN

FAV Displays the selected favourite programme.

MARK Select the input to apply the Picture Wizard settings.

Check and un-check programmes in the USB menu.

RATIO Selects your desired Aspect Ratio of picture. (???p.92)

MUTE Switches the sound on or off.

Programme Selects a programme.

UP/DOWN

PAGE UP/ Move from one full set of screen information to the DOWN next one.

SIMPLINK / Controls SIMPLINK or MY MEDIA menu(Photo List MY MEDIA Menu and Music List).

control buttons

See a list of AV devices connected to TV.

When you toggle this button, the Simplink menu appears at the screen.(???p.46)

AD Switches the Audio Description On or Off.

Installing Batteries

???Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +,-with -).

???Install two 1.5 V AAA batteries. Do not mix old or used batter- ies with new ones.

???Close cover.

???To remove the batteries, perform the installation actions in reverse.

contact the dealer where you purchased the TV. ??? Image shown may differ from your TV.

or

This item is not included for all models.

* Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth.

use on the screen. scratching or discolou- ration.

PREPARATION

Cable Holder

x 2

Component gender cable, AV gender cable

x 4

(M4x22)

(Only

32LE3***, 32LE4***, 32LE5***)

Bolts for stand assembly

Ferrite Core

(This item is not included for all models.)

PREPARATION

PREPARATION

FRONT PANEL CONTROLS

NOTE

???TV can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption.

???The energy consumed during use can be significantly reduced if the level of brightness of the picture

is reduced, and this will reduce the overall running cost.

CAUTION

???Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from frag- ments of glass, or the TV may fall.

???Do not drag the TV. The floor or the product may be damaged.

???Image shown may differ from your TV.

Only 32/37/42LE4***

Power/Standby Indicator

Note: You can turn the Power Indicator on or off in the OPTION menu.

Touch Sensor

??? You can use the SPEAKERdesired button func-

tion by touching.

Only 32/37/42LE4***

Only 19/22/26LE3***, 22/26LE5***

VOLUME MENU POWER

PROGRAMME OK INPUT

1

2

1Power/Standby Indicator

???Illuminates red in standby mode.

???The LED is off while the TV remains on.

2Remote Control Sensor

1

2

BACK PANEL INFORMATION

Only 19/22LE3***, 22LE5***

??? Image shown may differ from your TV.

11

12

13

PREPARATION

1DC ADAPTER PORT

Connect to the power cord socket.

2OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

3RGB/DVI Audio Input

Connect the audio from a PC or DTV.

4Audio/Video Input

Connect audio/video output from an external device to these jacks.

5Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

6Component Input

Connect a component video/audio device to these jacks.

7HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

8RGB IN Input

Connect the output from a PC.

9RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

10Antenna Input

Connect antenna or cable to this jack.

11USB Input

Connect USB storage device to this jack.

12PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT. (This feature is not available in all countries.)

13Headphone Socket

Plug the headphone into the headphone socket.

A-35

PREPARATION

Only 26LE3***, 26LE5***

??? Image shown may differ from your TV.

USB IN

IN 3

H/P HDMI

11

12

7

13

1DC ADAPTER PORT

Connect to the power cord socket.

2OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

3RGB/DVI Audio Input

Connect the audio from a PC or DTV.

4Audio/Video Input

Connect audio/video output from an external device to these jacks.

5Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

6Component Input

Connect a component video/audio device to these jacks.

A-36

7HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

8RGB IN Input

Connect the output from a PC.

9RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

10Antenna Input

Connect antenna or cable to this jack.

11USB Input

Connect USB storage device to this jack.

12PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT. (This feature is not available in all countries.)

13Headphone Socket

Plug the headphone into the headphone socket.

1

6

CAUTION

12

13

2

14 ??? Use a product with the following thickness for optimal connection to

PREPARATION

10

HDMI cable (Only HDMI IN 4) / USB device.

1Power Cord Socket

This TV operates on an AC power. The volt- age is indicated on the Specifications page. (??? p.137 to 147) Never attempt to operate the TV on DC power.

2HDMI/DVI IN Input

Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

3OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component. Use an Optical audio cable.

4RGB/DVI Audio Input

Connect the audio from a PC or DTV.

5Euro Scart Socket (AV1)

Connect scart socket input or output from an external device to these jacks.

6Component Input

Connect a component video/audio device to these jacks.

7RGB IN Input

Connect the output from a PC.

*A10 mm

8RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

9WIRELESS CONTROL

Connect the Wireless Media Box to the

WIRELESS CONTROL jack on the TV.

10Audio/Video Input

Connect audio/video output from an external device to these jacks.

11Antenna Input

Connect antenna or cable to this jack.

12USB Input

Connect USB storage device to this jack.

13PCMCIA (Personal Computer Memory Card International Association) Card Slot

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

14Headphone Socket

Plug the headphone into the headphone socket.

PREPARATION

Only 19/22LE3***, 22LE5***

screen from damage.

Only 26/32LE3***, 32/42/47LE4***, 26LE5***, 32/37/42/47/55LE5***

screen from damage.

M4 X 22(Only 32LE3***,

32LE4***, 32LE5***)

M4 X 24(Only 37/42LE4***,

37/42LE5***)

M4 X 26 (Only 47/55LE5***)

M4 X 20

(Only 26LE3***, 26LE5***)

3 Assemble the TV as shown.

Stand

Body

Stand

Base

M4 X 14

A-38

Downloaded From TV-Manual.com Manuals

Only 19/22/26LE3***, 22/26LE5***

After connecting the cables as necessary, install Cable Holder as shown and bundle the cables.

Only 32LE3***, 32/37/42LE4***, 32/37/42/47/55LE5***

It will help prevent the power cable from being removed by accident.

PREPARATION

PREPARATION

ATTACHING THE TV TO A

DESK (Only 32LE3***, 32LE4***, 32LE5***)

??? Ima4e shown may differ from your TV.

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.

1-Screw

(provided as parts of the product)

Stand

CONNECTION OF TV

(Only 19/22/26LE3***, 22/26LE5***)

??? Image shown may differ from your TV.

power outlet.

Desk

WARNING

???To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.

SWIVEL STAND

(Only 26/32LE3***, 32/37/42LE4***,

26LE5***, 32/37/42/47/55LE5***)

??? Image shown may differ from your TV.

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

CAUTION

???Please be sure to connect the TV to the DC power adapter before connecting the TV's power plug to a wall power outlet.

DESKTOP PEDESTAL

INSTALLATION

??? Image shown may differ from your TV.

For adequate ventilation allow a clearance of 10 cm all around the TV.

10 cm

10 cm

KENSINGTON SECURITY

SYSTEM

???This feature is not available for all models.

???Image shown may differ from your TV.

The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.

For the detailed installation and use of the Kensington Security System, refer to the user???s guide provided with the Kensington Security System.

For further information, contact http://www.kens- ington.com, the internet homepage of the Kensington

company. Kensington sells security systems for expensive electronic equipment such as note- book PCs and LCD projectors.

NOTE

???The Kensington Security System is an optional accessory.

???If the TV feels cold to the touch, there may be a small ???flicker??? when it is turned on. This is normal, there is nothing wrong with TV.

???Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

???Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

CAREFUL INSTALLATION

ADVICE

???You should purchase necessary components to fix the TV safety and secure to the wall on the market.

???Position the TV close to the wall to avoid the possibility of it falling when pushed.

???The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoid- ing the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.

11

2

22

1 Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the pic- ture.

(If your TV has bolts in the eyebolts, loosen then bolts.)

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

2 Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.

3

3 Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes horizontal between the wall and the product.

NOTE

???When moving the TV undo the cords first.

???Use a platform or cabinet strong and large enough to support the size and weight of the TV.

???To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

PREPARATION

A-41

PREPARATION

A-42

???The TV can be installed in various ways such as on a wall, or on a desktop etc.

???The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to earth the TV by connecting it to tele- phone wires, lightening rods or gas pipes.

Power

Supply

Circuit breaker

WALL MOUNT: HORIZONTAL

INSTALLATION

???We recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall.

???We recommend that you purchase a wall mount- ing bracket which supports VESA standard.

???LG recommends that wall mounting be per- formed by a qualified professional installer.

NOTE

???Should Install wall mount on a solid wall per- pendicular to the floor.

???Should use a special wall mount, if you want to install it to ceiling or slanted wall.

???The surface that wall mount is to be mount- ed on should be of sufficient strength to sup- port the weight of TV set; e.g. concrete, nat- ural rock, brick and hollow block.

???Installing screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount.

???LG is not liable for any accidents or damage to property or TV due to incorrect installa- tion:

-Where a non-compliant VESA wall mount is used.

-Incorrect fastening of screws to surface which may cause TV to fall and cause per- sonal injury.

-Not following the recommended Installation method.

10 cm

10 cm

10 cm

< Only 26LE3***, 26LE5*** >

??? Image shown may differ from your TV.

4-Ring spacers

Place the ring spacers on the set before installing the wall mounting bracket so that the inclination of the backside of the set can be adjusted perpendicularly.

1

1

REMOTE CONTROL KEY FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV. ??? Image shown may differ from your TV.

(POWER) Switches the TV on from standby or off to standby.

ENERGY Adjust the Energy Saving mode of the TV.(???p.95)

SAVING

AV MODE It helps you select and set images and sounds when connecting AV devices.(???p.50)

INPUT External input mode rotate in regular sequence.(???

p.43)

TV/RAD Selects Radio, TV and DTV channel.

0 to 9 number Selects a programme.

button Selects numbered items in a menu.

LIST Displays the programme table. (???p.41)

Q.VIEW Returns to the previously viewed programme.

MENU Selects a menu.

Clears all on-screen displays and returns to TV viewing from any menu.(???p.19)

GUIDE Shows programme guide.(???p.86)

Q. MENU Select the desired quick menu source. (Aspect

Ratio, Clear Voice II , Picture Mode, Sound Mode,

Audio (or Audio Language), Sleep Timer, Skip Off/

On, USB Device).(??? p.18)

BACK Allows the user to move return one step in an inter- active application, EPG or other user interaction function.

EXIT Clears all on-screen displays and returns to TV viewing from any menu.

INFO i Shows the present screen information.

THUMBSTICK Allows you to navigate the on-screen menus and (Up/Down/Left/Right) adjust the system settings to your preference.

OK Accepts your selection or displays the current mode.

PREPARATION

A-43

PREPARATION

2

2

A-44

VOLUME UP Adjusts the volume. /DOWN

FAV Displays the selected favourite programme.

MARK Select the input to apply the Picture Wizard settings.

Check and un-check programmes in the USB menu.

RATIO Selects your desired Aspect Ratio of picture. (???p.92)

MUTE Switches the sound on or off.

Programme Selects a programme.

UP/DOWN

PAGE UP/ Move from one full set of screen information to the DOWN next one.

2 SIMPLINK / Controls SIMPLINK or MY MEDIA menu(Photo List MY MEDIA Menu and Music List or Movie List).

control buttons

See a list of AV devices connected to TV.

When you toggle this button, the Simplink menu appears at the screen.(???p.46)

AD Switches the Audio Description On or Off.

Installing Batteries

???Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +,-with -).

???Install two 1.5 V AAA batteries. Do not mix old or used batter- ies with new ones.

???Close cover.

???To remove the batteries, perform the installation actions in reverse.

EXTERNAL EQUIPMENT SETUP

???To prevent damage do not connect to the mains outlet until all connections are made between the devices.

ANTENNA CONNECTION

???For optimum picture quality, adjust antenna direction.

???An antenna cable and converter are not supplied.

RF Coaxial Wire (75 ??)

Outdoor

Antenna

(VHF, UHF) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

???In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above.

???If signal needs to be split for two TVs,use an antenna signal splitter for connection.

SETUP EQUIPMENT EXTERNAL

SETUP EQUIPMENT EXTERNAL

???HDMI Audio Supported format : Dolby Digital, PCM DTS Audio format is not supported.

1

2

or

1

2

2

Component Input ports

To achieve better picture quality, connect a DVD player to the component input ports as shown below.

CONNECTING WITH AN HDMI CABLE

NOTE

???The TV can receive video and audio signals simultaneously when using an HDMI cable.

???If the DVD does not support Auto HDMI, you must set the output reso- lution appropriately.

???Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed HDMI Cable, flickering or no screen dis- play can result. Please use the High Speed HDMI Cable.

SETUP EQUIPMENT EXTERNAL

3

SETUP EQUIPMENT EXTERNAL

4

or

CONNECTING WITH A EURO SCART CABLE

SETUP EQUIPMENT EXTERNAL

???TV Out : Outputs Analogue TV or Digital TV signals.

SETUP EQUIPMENT EXTERNAL

CONNECTING WITH A RF CABLE

To avoid picture noise (interference), allow adequate distance between the VCR and TV.

VCR for viewing.

2

Wall Jack

6

Antenna

or

Video Game Set

Camcorder

SETUP EQUIPMENT EXTERNAL

SETUP EQUIPMENT EXTERNAL

8

CONNECTING WITH A D-SUB 15 PIN CABLE

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's set- tings.

21

INSERTION OF CI MODULE

To view the encrypted (pay) services in digital TV mode. This feature is not available in all countries.

Association) CARD SLOT of TV as shown.

For further information, see p.34.

NOTE

???Check if the CI module is inserted into the PCMCIA card slot in the right direction. If the module is not inserted properly, this can cause damage to the TV and the PCMCIA card slot.

Check this point as shown and insert the CI Module.

SETUP EQUIPMENT EXTERNAL

SETUP EQUIPMENT EXTERNAL

10

DIGITAL AUDIO OUT SETUP

Sending the TV???s audio signal to external audio equipment via the Digital Audio Output (Optical) port.

If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).

AUDIO menu.(???p.112). Refer to the external audio equipment instruction manual for opera- tion.

2

CAUTION

???Do not look into the optical output port. Looking at the laser beam may damage your vision.

EXTERNAL EQUIPMENT WIRELESS CONNECTION

(Only 32/42/46/52/60LD5***, 32LE3***, 32/37/42LE4***, 32/37/42/47/55LE5***)

You can connect between TV and external equipment wirelessly.

For further information, refer to the ???LG Wireless Media Box??? manual for operating instructions.

LG Wireless Media Box

SETUP EQUIPMENT EXTERNAL

11

EQUIPMENT EXTERNAL

SUPPORTED DISPLAY RESOLUTION

(Except for 19/22/26LD3***, 26/32LD32**, 32LD34**, 19/22/26/32LE3***, 26/32LD33**)

SETUP

12

NOTE

???Avoid keeping a fixed image on the set???s screen for prolonged periods of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible.

???There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

???The synchronization input waveform for Horizontal and Vertical frequencies are separate.

???We recommend using 1920x1080, 60 Hz(Except

for 19/22/26LD3***, 26/32LD32**, 32LD34**, 19/22/26/32LE3***, 26/32LD33**), 1360x768, 60 Hz(Only 19/22/26LD3***, 26/32LD32**, 32LD34**, 19/22/26/32LE3***, 26/32LD33**) for the PC mode, this should provide the best picture quality.

???Connect the signal cable from the monitor output port of the PC to the RGB (PC) port of the TV or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the TV.

???Connect the audio cable from the PC to the Audio input on the TV. (Audio cables are not included with the TV).

???If using a sound card, adjust PC sound as required.

???If the graphic card on the PC does not output ana- logue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV.

???If the graphic card on the PC does output analogue and digital RGB simultaneously, set the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.)

???DOS mode may not work depending on the video card if you use an HDMI to DVI cable.

???If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of cable. This provides the best picture quality.

SCREEN SETUP FOR PC MODE

Screen Reset

Returns Position, Size and Phase to the factory default settings.

This function works in the following mode : RGB[PC].

EQUIPMENT EXTERNAL

1

2

3

4

Reset

Select PICTURE.

Select Screen.

Select Reset.

Select Yes.

SETUP

SETUP EQUIPMENT EXTERNAL

Auto Configure (RGB [PC] mode only)

Automatically adjusts the picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment.

Auto configure

This function is for automatic adjustment of the screen position, size, and phase The displayed image will be unstable for a few seconds while the auto configuration is in progress.

Reset

1

2

3

4

5

Select PICTURE.

Select Screen.

Select Auto Config..

Select Yes.

Run Auto Config..

???If the position of the image is still not correct, try Auto adjustment again.

???If picture needs to be adjusted again after Auto adjustment in RGB (PC), you can adjust the Position, Size or Phase.

Selecting Resolution

To view a normal picture, match the resolution of RGB mode and selection of PC mode.

This function works in the following mode: RGB[PC]

EQUIPMENT EXTERNAL

1

2

3

4

Reset

Select PICTURE.

Select Screen.

Select Resolution.

Select the desired resolution.

SETUP

EQUIPMENT EXTERNAL

Adjustment for screen Position, Size, Phase

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture position manually.

This function works in the following mode : RGB[PC].

SETUP

1

2

3

Reset

Select PICTURE.

Select Screen.

Select Position, Size or Phase.

4

Make appropriate adjustments.

WATCHING TV / PROGRAMME CONTROL

TURNING ON THE TV

When your TV is turned on, you will be able to use its features.

will switch on.

INITIALIZING SETUP

CONTROL PROGRAMME / TV WATCHING

1

2

Press the + or - button to adjust the volume.

If you wish to switch the sound off, press the MUTE button.

You can cancel this function by pressing the MUTE, + , - or AV Mode button.

/ TV WATCHING

Aspect Ratio: Selects your desired picture for- mat.

For Zoom Setting, select 14:9, Zoom and Cinema Zoom in Ratio Menu. After complet- ing Zoom Setting, the display goes back to Q.Menu.

Clear Voice II : By differentiating the human sound range from others, it helps users lis- ten to human voices better.

Picture Mode : Selects your desired Picture Mode.

Sound Mode : It is a feature to automatical- ly set the sound combination which it deems the best for the images being watched.

Selects your desired Sound Mode.

Audio or Audio Language : Selects the sound output.

Sleep Timer : Sets the sleep timer.

Skip Off/On : Selects the Skip Off/On.

USB Device : Selects ???Eject??? in order to eject USB device.

CONTROL PROGRAMME

???Aspect Ratio ???

16:9

1

2

3

Display each menu.

Select your desired Source.

???Press the Q.MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

ON SCREEN MENUS SELECTION AND ADJUSTMENT

Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.

(Except for 19/22/26/32LD3***, 32/37/42/47LD4***, 19/22/26LE3***, 22/26LE5***)

CONTROL PROGRAMME / TV WATCHING

1

2

3

Display each menu.

Select a menu item.

Move to the pop up menu.

???Press the RED button, you can check the

Customer Support menu.

???Press the GREEN button, you can check the Simple Manual menu.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the pre- vious menu screen.

NOTE

???It is not possible to use CI Information in Analogue mode.

???IR Blaster : For further information, refer to the optional ???Wireless Media Box??? manual for operat- ing instructions.

???It is possible to use Movie List menu in 19/22/26/32LE3***, 32/37/42LE4***, 22/26LE5***,

32/37/42/47/55LE5***, 32/42/46/52/60LD56**, 32/37/42/47LD46**, 32/42/46/52/60LD555, 32/3742/47LD455, 19/22/26/32LD355, 19/22/26/32LD356, 19/22/26/32LD345, 19/22/26/32LD346

Downloaded From TV-Manual.com Manuals

32/37/42/47LD425, 32/37/42/47LD426, 26/32LD335, 26/32LD336.

19

PROGRAMME / TV WATCHING

If you want to select the Antenna,

Move OK

Please select your TV Connection.

Antenna Cable

If you select antenna or cable, existing channel information is deleted.

Antenna Cable

Close

Antenna

Antenna

Check your antenna connection. The previous channel information will be updated during Auto Tuning.

SECAM L Search

Automatic Numbering

Start

Close

CONTROL

1

2

3

4

5

Select SETUP.

Select Auto Tuning.

Select Antenna.

Select Start.

Run Auto tuning.

???Use NUMBER buttons to input a 4-digit password in Lock System ???On???.

???If you wish to keep on auto tuning select

Start using the button. Then, press the OK button. Otherwise select Close.

???Automatic Numbering: Decide whether to use the programme numbers as sent by broadcasting stations for tuning.

???When select Italy in the County menu, If the pop up is displayed when the conflict- ed programme after Auto Tuning, select a broadcaster for Conflicting programme number to solve.

???Manual Tuning

???Programme Edit

???CI Information

???Cable DTV Setting

SETUP

???Auto Tuning

???Manual Tuning

???Programme Edit

???CI Information

???Cable DTV Setting

Move OK

Please select your TV Connection.

Antenna Cable

If you select antenna or cable, existing channel information is deleted.

Antenna Cable

Close

???Programme Edit Other Operators

???CI Information

WATCHING

1

2

3

4

5

Select SETUP.

Select Auto Tuning.

Select Cable.

Select Comhem or Other Operators.

Select Quick or Full.

???Use NUMBER buttons to input a 4-digit password in Lock System ???On???.

???When you select the Cable, the Cable Service Operator selection screen can differ or not exist by the Cable situation of the applicable country.

???The popup window to select Service Operator is only shown initially for the 3 cases when you accessing the Initial Setting menu, when you change from Antenna to Cable or when you access the menu after changing the Country.

???When you want to select Service Operator aside from the above 3 cases, you can do so by selecting Setup->Cable DTV Setting-> Service Operator.

CONTROL PROGRAMME / TV

/ TV WATCHING

??? When you select the Quick,

Cable

Cable

Check your antenna connection. The previous channel information will be updated during Auto Tuning.

Skip Scramble Programme

Automatic Numbering

Start

Close

CONTROL PROGRAMME

6

7

8

9

10

11

12

Select Quick.

Select Setting.

Make appropriate adjustments.

Select Close.

Select OK.

Select Start.

Run Auto tuning.

???If you wish to keep on auto tuning, select

Start using the button. Then, press the OK button. Otherwise select Close.

???Automatic Numbering: Decide whether to use the programme numbers as sent by broadcasting stations for tuning.

???Skip Scramble Programme : Scramble Programme is skipped in Auto Tuning and Manual Tuning.

??? When you select the Full,

Full

Search every available signal.

OK

Close

Cable

Cable

Check your antenna connection. The previous channel information will be updated during Auto Tuning.

Skip Scramble Programme

Automatic Numbering

Start

Close

6

7

8

9

Select Full.

Select OK.

Select Start.

Run Auto tuning.

???If you wish to keep on auto tuning, select

Start using the button. Then, press the OK button. Otherwise select Close.

???Automatic Numbering: Decide whether to use the programme numbers as sent by broadcasting stations for tuning.

???Skip Scramble Programme : Scramble Programme is skipped in Auto Tuning and Manual Tuning.

???You can not select the Full when the service operator is set to "Ziggo" or "Other Operators" of Netherlands.

CONTROL PROGRAMME

CABLE DTV SETTING

(IN CABLE MODE ONLY)

The range that a user can select from the Service Operator menu differs depending on number of Service Operator supported by each country, and if number of supported Service Operator for each country is 1, corresponding function becomes non-activation.

After changing Service Operator, a warning window saying that channel map will be deleted when OK button is pressed or Close is selected, and a Auto-tuning pop-up window appears when ???YES??? is selected.

PROGRAMME / TV WATCHING

1

2

3

4

Select SETUP.

Select Cable DTV Setting.

Select Service Operator or Channel Auto Update.

Select your desired Source.

???If you select Cable, you can see Cable DTV Setting menu.

???When Channel Auto Update is On, you can update information for all the pro- grammes that can be updated, including the programme currently being watched.

???When Channel Auto Update is Off, you can only update information for the pro- gramme currently being watched.

???You can not select the Cable DTV Setting when the service operator is set to "Ziggo".

CONTROL

CONTROL PROGRAMME / TV WATCHING

1

2

3

4

5

Select the desired channel number.

Select update or add if signal present.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

If you want to select the Cable,

/ TV WATCHING

1

2

3

4

Select SETUP.

Select Manual Tuning.

Select Cable DTV.

Make appropriate adjustments.

???Use NUMBER buttons to input a 4-digit password in Lock System ???On???.

???Symbol rate : Enter a user-defined

symbol rate (Symbol rate: Speed at which a device such as modem sends symbols to a channel).

???Modulation : Enter a user-defined

modulation. (Modulation: Loading of audio or video signals onto carrier).

???You can not select the Cable DTV when the service operator is set to "Ziggo" or "Other Operators" of Netherlands.

CONTROL PROGRAMME

CONTROL PROGRAMME / TV WATCHING

28

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

???Use NUMBER buttons to input a 4-digit password in Lock System ???On???.

???L : SECAM L/L??? (France)

BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa)

I : PAL I (U.K. / Ireland / Hong Kong / South Africa)

DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)

???To store another channel, repeat steps 4 to 9.

??? Assigning a station name

You can assign a station name with five characters to each programme number.

TV WATCHING

1

Select SETUP.

Select the position and make your choice of the second

/

2

5

character, and so on.

You can use an the alphabet

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

29

CONTROL PROGRAMME / TV WATCHING

PROGRAMME EDIT

When a programme number is skipped, it means that you will be unable to select it using P button during TV viewing.

If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu.

This function enables you to skip the stored programmes.

You can change the programme number using ???Move???function, if ???Automatic Numbering??? is unchecked when you start Auto Tuning.

1

2

Select SETUP.

Select Programme Edit.

??? Skipping a programme number

1

Select a programme number to be skipped.

2

BLUE Turn the programme number to blue.

3

BLUE Release.

???When programmes are to be skipped, the skipped programme shows in blue and these programmes will not be selected by the P buttons during TV viewing.

???If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.

??? Locking a programme number

1

Select a programme number to be locked.

2

YELLOW Turn the programme number to yellow.

3

YELLOW Release.

???It can be registered as Lock programme even when Lock System is turned Off.

PROGRAMME / TV WATCHING

IN TV MODE

This function enables you to delete or skip the stored programmes.

You can also move some channels and use other programme numbers.

??? Deleting a programme

1

Select a programme number to be deleted.

CONTROL

31

??? Skipping a programme number

1

Select a programme number to be skipped.

2

BLUE Turn the programme number to blue.

3

BLUE Release.

???When a programme number is skipped it means that you will be unable to select it

using the P button during normal TV viewing.

???If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.

/ TV WATCHING

CONTROL PROGRAMME

??? Locking a programme number

1

Select a programme number to be locked.

2

YELLOW Turn the programme number to yellow.

3

YELLOW Release.

???It can be registered as Lock programme even when Lock System is turned Off.

3

32

Release.

1

2

Select your desired programme.

Display a pop-up window where Favourite group can be changed.

/ TV WATCHING

CI [COMMON INTERFACE] INFORMATION

This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you cannot watch pay services.

When the module is inserted into the CI slot, you can access the module menu.

To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CI module from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI Module, you may not have any sound output.

This may be incompatible with the CI module and smart card.

CI (Common Interface) functions may not be possible depending upon the country broadcasting cir- cumstances.

When using a CAM(Conditional Access Module), please make sure it meets fully the requirements of either DVB-CI or CI plus.

CONTROL PROGRAMME

1

2

Select the item

??? This OSD is only for illustration and the menu options and screen format will vary according to the Digital pay services provider.

??? It is possible for you to change CI (Common Interface) menu screen and service by consult- ing your dealer.

Select SETUP.

Select CI Information.

SOFTWARE UPDATE

Software Update means software can be downloaded through the digital terrestrial broadcasting system.

/ TV WATCHING

1

2

RED Select Customer Support.

PROGRAMME

??? If you select On, a user confirm message box will be displayed to notify that new software is found.

4

Save.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

CONTROL

35

WATCHING

Occasionally, a transmission of updated digital software infor- mation will result in the following menu on the TV screen.

?Software update is available. Would you like to download now?

Yes

No

Simple Update : for current update stream

Download starts when "Yes" is selected. At this time, pro- gressing pop-up window does not display.

Download progress status can be checked from Software Update menu.

Software Update ??? On ???

Software downloading progress.

Ver. 00.00.01 ??? Ver.00.00.00

4%

Close

A window as display below appears when download completes.

TV is restarted when "Yes" is selected.

New software version is ready. If you want to install now, TV will be turned off and restart. Continue?

CONTROL PROGRAMME / TV

?A new software update is available at 00/00/0 00:00.

Do you want to update the software when available?

Yes

No

Schedule Update : for scheduled

update stream

When the Software Update menu is "Off", the message to change it to "On" appears.

- During Progress of a Software Update, please note the following:

???Power to the TV must not be interrupted.

???The antenna must not be disconnected.

???After Software Update, you can confirm the updated software version in Software Update menu.

???It may take hours to download the software, so make sure that the power stays on during the download.

???The software is downloaded only in Standby mode or in MUX with Software Update Service, and stops when the power cord is unplugged or when viewing MUX without Software Update Service.

???When you return to Standby mode or MUX with Software Update Service, the software download will resume from where it stopped.

Signal Test

Product/Service Info.

Close

Press OK() to set programme settings.

?Do you have a problem in this test screen?

/ TV WATCHING

1

2

RED Select Customer Support.

Select Picture Test or Sound Test.

PROGRAMME

3

Select Yes or No.

CONTROL

CONTROL PROGRAMME / TV WATCHING

38

This function enables you to view information on the Manufacturer, Model/Type, Serial Number and Software Version.

This displays the information and signal strength of the tuned *MUX.

This displays the signal information and service name of the selected MUX.

(*MUX: A higher directory of channels in digital broadcasting (a single MUX contains multiple chan- nels.))

4

Display the information of Channel.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

1

2

3

Press OK() to set programme settings.

RED Select Customer Support.

Select Product/Service Info..

Display MODEL/TYPE, Software version, Serial Number,

Customer service center and Homepage.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

CONTROL PROGRAMME / TV WATCHING

39

CONTROL PROGRAMME / TV WATCHING

Press OK() to set programme settings.

2

Select the part of the manual you want to see.

??? Press the EXIT button to return to normal TV viewing.

SELECTING THE PROGRAMME LIST

You can check which programmes are stored in the memory by displaying the programme list.

2BBC

3BBC

4BBC

Pr.Edit

TV WATCHING

??? Displaying programme LIST

1

Display the Programme List.

???You may find some blue programmes. These have been set up to be skipped by auto programming or in the programme edit mode.

???Some programmes with the channel num- ber shown in the programme LIST indicate there is no station name assigned.

PROGRAMME /

BLUE Turn the programme edit.

CONTROL

CONTROL PROGRAMME / TV WATCHING

42

??? Displaying the favourite programme list

3 BBC

INPUT LIST

HDMI and AV1 (SCART) can be recognized by a detect pin and thus enabled only when an external device approves voltage.

By using TV/RAD button, you can move from External Input to RF Input and to the last watched pro- gramme in DTV/RADIO/TV mode.

??? USB : Select it when using USB depends on connector.

??? AV : Select it when watching the VCR or external equipment.

??? Component : Select it when using the DVD or the Digital set-top box depends on connector.

??? RGB :Select it when using PC depends on connector.

??? HDMI : Select it when using DVD, PC or Digital set-top box depend on connector.

CONTROL PROGRAMME / TV WATCHING

WATCHING

CONTROL PROGRAMME / TV

1

2

3

Close

BLUE Select Input Label.

Select the source.

Select the label.

1

2

3

4

???Disability Assistance

???Power Indicator

Select OPTION.

Select Data Service.

Select MHEG or Teletext.

Save.

???Disability Assistance

???Power Indicator

WATCHING

SIMPLINK

This function operates only with devices with the SIMPLINK logo.

Please check the SIMPLINK logo.

This TV might not function properly when using it with other products with HDMI-CEC function.

This allows you to control and play other AV devices connected to the display through HDMI cable with- out additional cables and settings.

If you do not want SIMPLINK menu,select ???Off???.

In wireless external output, SIMPLINK function is not supported.

CONTROL PROGRAMME / TV

1

2

3

OK Exit

??? On ???

Watch TV

DISC

VCR

VCRHDD Recorder

??? Speaker ???

TV Speaker

Display the SIMPLINK.

Select On or Off.

Save.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

Connecting to Home Theater with the SIMPLINK logo.

NOTE

???Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the terminal (HDMI terminal) of the SIMPLINK device with the HDMI cable.

???When you switch the Input source using the INPUT button on the remote control, you can stop the opera- tion of a device controlled by SIMPLINK.

CONTROL PROGRAMME / TV WATCHING

47

CONTROL PROGRAMME / TV WATCHING

SIMPLINK Functions

Disc playback

Control connected AV devices by pressing the , OK, ???, ???, ll, ?????? and ?????? buttons.

Direct Play

After connecting AV devices to the TV, you can directly control the devices and play media without additional set- tings.

Select AV device

Enables you to select one of the AV devices connected to the TV and operate it.

Power off all devices

When you switch off the TV, all connected devices are turned off.

Switch audio-out

Offers an easy way to switch audio-out.

Sync Power on

When the equipment with Simplink function connected HDMI terminal starts to play, The TV will change automatically to turn on mode.

* A device, which is connected to the TV through an HDMI cable but does not support SIMPLINK, does not provide this function.

Note: To operate SIMPLINK, an High Speed HDMI Cable with *CEC function should be used.

(*CEC: Consumer Electronics Control).

SIMPLINK Menu

Press the button and then OK button to select the desired SIMPLINK source.

1 TV viewing : Switch to the previous TV pro- gramme regardless of the current mode.

4HDD Recordings playback : Play and con- trol recordings stored in HDD.

5Audio Out to Home theater/Audio Out to TV: Select Home theater or TV speaker for Audio Out.

???Home theater: Only one supported at a time

???DVD, Recorder: Up to one(Only 19/22LD3***), two(Only 26/32LD3***, 32/37/42/47LD4***, 19/22LE3***, 22LE5***), three(Only 32/42/46/52/60LD5***, 26LE3***, 26LE5***), four(Only 32LE3***, 32/37/42LE4***, 32/37/42/47/55LE5***) supported at a time.

???VCR: Only one supported at a time

CONTROL PROGRAMME / TV WATCHING

CONTROL PROGRAMME / TV WATCHING

1AV MODE

2

Press the AV MODE button repeatedly to select the desired source.

???If you select Cinema in AV mode, Cinema will be selected both for

Picture Mode and Sound Mode in PICTURE menu and AUDIO menu respectively.

???If you select ???Off??? in AV mode, the picture and image which you initially set will be selected.

???When playing a video game using PlayStation or Xbox, it is recom- mended to use the Game mode.

???When in Game mode, functions related to picture quality will be opti- mized for playing games.

INITIALIZING(RESET TO ORIGINAL FACTORY SETTINGS)

This function initializes all settings.

But the settings of Day and Night of the Picture Mode cannot be initialized. It is useful to initialize the product or when you move to other city or country.

When the Factory Reset is completed, you must restart the Initializing setup.

When the Lock System menu is "On", the message to enter the password appears.

CONTROL PROGRAMME / TV WATCHING

1

2

3

4

Select OPTION.

Select Factory Reset.

Select Yes.

Start Factory Reset.

???In Lock System "On", if you forget your password, press '0', '3', '2', '5' on the remote control hands et.

DEVICE USB A USE TO

1 Connect the USB device to the USB IN jack on the TV.

or

2 Select Movie List (Only 19/22/26/32LE3***, 32/37/42LE4***, 22/26LE5***, 32/37/42/47/55LE5***, 32/42/46/52/60LD56**, 32/37/42/47LD46**, 32/42/46/52/60LD555, 32/3742/47LD455, 19/22/26/32LD355, 19/22/26/32LD356, 19/22/26/32LD345, 19/22/26/32LD346 32/37/42/47LD425, 32/37/42/47LD426,

26/32LD335, 26/32LD336), Photo List or

Music List.

MY MEDIA

???Only photo(JPEG), music (MP3) and movie (DAT,MPG,MPEG,VOB,AVI,DIVX,MP4,MKV,T S,TRP,TP,ASF,WMV,FLV) are supported.

When removing the USB device

Select the USB Device menu before removing the USB device.

1

Select USB Device.

2

Select Eject.

DEVICE USB A USE TO

MOVIE LIST

(Only 19/22/26/32LE3***, 32/37/42LE4***, 22/26LE5***, 32/37/42/47/55LE5***, 32/42/46/52/60LD56**, 32/37/42/47LD46**, 32/42/46/52/60LD555, 32/3742/47LD455, 19/22/26/32LD355, 19/22/26/32LD356, 19/22/26/32LD345, 19/22/26/32LD346 32/37/42/47LD425, 32/37/42/47LD426, 26/32LD335, 26/32LD336)

You can play movie files on a USB storage device.

The movie list is activated once USB is detected. It is used when playing movie files on TV. Displays the movies in the USB folder and supports Play.

Allows playback of all movies in the folder and user desired files. It is a movie list that displays folder information and movie file.

The On Screen Display may be different from your TV. Images are an example to assist with the TV operation.

Movie(*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.vob/*.mp4/*.mov/*.mkv/*.dvix/*.avi/*.asf/*.wmv/*.flv/*.avi(motion-jpeg)/*. mp4(motion-jpeg)/*.mkv(motion-jpeg))supporting file

Video format : DivX3.11, DivX4.12, DivX5.x, DivX6, Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10 beta-1/beta-2, Mpeg-1, Mpeg-2, Mpeg-4, H.264/AVC, VC1, JPEG, Sorenson H.263

Audio format : Dolby Digital, AAC, Mpeg, MP3, LPCM, HE-AAC, ADPCM, WMA

Bit rate : within 32 kbps to 320 kbps(MP3)

External Subtitle format : *.smi/*.srt/*.sub(MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.psb(PowerDivX)

Internal Subtitle format : only, XSUB (It is the subtitle format used in DivX6 files)

???Some user-created subtitles may not work properly.

???Some special characters are not supported in subtitles.

???HTML tags are not supported in subtitles.

???Subtitles in languages other than the supported languages are not available.

???The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio language is changed.

???A damaged movie file may not be played correctly, or some player functions may not be usable.

???Movie files produced with some encoders may not be played correctly.

???If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.

???HD videos with a maximum of 1920x1080@25/30P or 1280x720@50/60P are supported, depending on the frame.

???Videos with resolutions higher than 1920X1080@25/30P or 1280x720@50/60P may not work properly depending on the frame.

???Movie files other than the specified types and formats may not work properly.

???Max bitrate of playable movie file is 20 Mbps. (only, Motion JPEG : 10 Mbps)

???We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.

???DTS Audio codec is not supported.

???A movie file more than 30 GB in file size is not supported for playback.

???A DivX movie file and its subtitle file must be located in the same folder.

???A video file name and its subtitle file name must be identical for it to be displayed.

???Playing a video via a USB connection that doesn???t support high speed may not work properly.

???Files encoded with GMC(Global Motion Compensation) may not be played.

???When you are watching the movie by Movie List function, you can adjust an image by Energy Saving and AV Mode key on the remote control. User setup for each image mode does not operate.

DEVICE USB A USE TO

USE TO

1

Select MY MEDIA.

1Moves to upper level folder

2Current page/Total pages

3Corresponding buttons on the remote control

4Contents under the folder focused on 1

5Current page/ total pages of contents under the folder focused on 1

DEVICE USB A

3

???Some files may be displayed the preview image by icon only.

???Non-supported files are displayed the preview image by icon only.

???Abnormal files are displayed in the form of bitmap.

2

movie page.

Select the desired movie title.

A USE

3

Movie files are played.

DEVICE USB

DEVICE USB A USE TO

??? When selected movie files are played

1

Select the target folder or drive.

2

Select the desired movie title.

3

BLUE or Convert to Mark Mode.

???When one or more movie files are marked, the marked movies will be played in sequence.

58

NOTE

??? In the case of files not supported, a message regarding non-supported file is displayed.

Using the remote control

YELLOW Deselect all marked movie files.

BLUE Exit the Mark Mode.

NOTE

???If you select ???Yes??? from OSD when playing the same file after the movie file has been stopped, it will restart where it stopped previously.

???If continuous series files exist within the folder, the next file will automatically be played.

But, this excludes cases when the Repeat function of Movie List Option is turned ???On??? (Refer to p. 62) or when set as Marked Play.

DEVICE USB A USE TO

59

DEVICE USB A USE TO

2 Select Set Video Play., Set Video. or Set

Audio..

NOTE

?????? / ??????

or

< >

ENERGY

SAVING

AV MODE

When playing,

repeatedly, press the REW(??????) button to speed up ??????(x2) -> ?????????(x4) ->

????????????(x8) ->???????????????(x16) ->??????????????????(x32) .

repeatedly, press the FF(??????) button to speed up ??????(x2)-> ?????????(x4) ->

????????????(x8) ->???????????????(x16) -> ??????????????????(x32).

??? Pressing these buttons repeatedly increases the fast forward/reverse speed.

Show the Option menu.

Hide the menu on the full-sized screen.

???To see the menu again on the full-sized screen, press OK button to display.

Return to normal TV viewing.

???When using the < or > button during playback a cursor indicating the position can be viewed on the screen.

Press the ENERGY SAVING button repeatedly to change the brightness of your screen.(Refer to p. 95)

Press the AV MODE button repeatedly to select the desired source.(Refer to p. 50)

DEVICE USB A USE TO

DEVICE USB A USE TO

???Picture Size : Selects your desired picture format during movie play.

???Audio Language : Changes the Language Group of the audio during movie play. Files with a single audio track cannot be selected.

???Subtitle Langugae : Turn on/off the subtitle.

???Language : Activated for SMI subtitle and can select the language within the subtitle.

???Code page : Can select the font for subti- tle. When set to default, same font as gen- eral menu will be used.

???Sync : Adjusts the time synchronisation of the subtitle from -10 secs to +10 secs by steps of 0.5 secs during movie play.

???Position : Changes the position of the subtitle either up or down during movie play.

???Size : Selects your desired Subtitle size during movie play.

???Repeat : Turn on/off repeat function of movie playback. When turned on, the file within the folder will be played back repeatedly. Even when the repeated play- back is turned off, it can run the playback if the file name is similar to the previous file.

62

NOTE

???Only 10,000 of sync blocks can be supported within the subtitle file.

???When playing a video, you can adjust the Picture Size by pressing the RATIO button.

??? When you select the Set Video,

1

Select Picture Mode or TruMotion.

DEVICE USB A USE TO

63

DEVICE USB A USE TO

64

1

Select MY MEDIA.

1Moves to upper level folder

2Current page/Total pages

3Corresponding buttons on the remote control

4Contents under the folder focused on 1

5Current page/ total pages of contents under the folder focused on 1

2

Select Photo List.

DEVICE USB A USE TO

DEVICE USB A USE TO

Photo Selection

??? When playing photo files

2

Select the desired photos.

3

Photo files are displayed.

1

Select the target folder or drive.

???When one or more photos are marked, you can view each marked photo or a slide show of the marked photos. If no photos are marked, you can view every individual photo in the folder or a slide show of all photos in the folder.

DEVICE USB A USE TO

67

How to view photo

Detailed operations are available on full-sized photo view screen.

01_a.jpg 2008/12/10 1920 x 1080 479 KB

The aspect ratio of a photo may change the size of the photo displayed on the screen in full size.

Press the EXIT button to move to the previous menu screen.

???2/13 ???

DEVICE USB A USE TO

1

2

3

Select the target folder or drive.

Select the desired photos.

The selected photo is displayed in full size.

???Use the P button to navigation in the photo page.

DEVICE USB A USE TO

70

???Slideshow : When no picture is selected, all photos in the cur- rent folder are displayed during slide show. If some photos are selected, those photos are displayed in a slide show.

???Set the time interval of the slide show in Option.

???BGM (Background Music) : Listen to music while viewing photos in full size.

???Set the BGM device and album in Options before using this function.

???You can adjust Option by Q.MENU or MENU button on the remote control.

?????? (Rotate) : Rotate photos.

???Rotates the photo 90??, 180??, 270??, 360?? clockwise.

???It can not be rotate when the width of a picture is bigger than supported height.

??? (ZOOM IN): View the photo by zoom in 2, 4 times.

??? : Press the ENERGY SAVING button repeatedly to change the brightness of your screen.(Refer to p. 95)

???Option : Set values for Slide Speed and BGM.

???Use button and OK button to set values. Press OK to save the settings.

???You cannot change BGM while BGM is playing.

???Hide : Hide the menu on the full-sized screen.

???To see the menu again on the full-sized screen, press OK button to display.

Press the EXIT button to go back to Photo List.

Using the Photo List function

???2/13 ???

2 Select Set Photo View., Set Video. or Set

Audio..

NOTE

???Option values changed in Movie List does not affect Photo List and Music List.

???Option value changed in Photo List and Music List are changed likewise in Photo List and Music List excluding Movie List.

DEVICE USB A USE TO

71

1

2

Select Slide Speed or BGM.

Make appropriate adjustments.

??? When you select the Set Video,

1

Select Picture Mode or TruMotion.

DEVICE USB A USE TO

73

DEVICE USB A USE TO

74

MUSIC LIST

You can play music files on USB storage device.

Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be supported by this model.

Music file on your USB device can be played by this unit.

The On Screen Display may be different from your TV. Images are an example to assist with the TV operation.

MUSIC (*.MP3) supporting file

Bit rate 32 to 320

???Sampling rate MPEG1 Layer3 : 32 kHz, 44.1 kHz, 48 kHz

???Sampling rate MPEG2 Layer3 : 16 kHz, 22.05 kHz, 24 kHz

???Sampling rate MPEG2.5 Layer3 : 8 kHz, 11.025 kHz, 12 kHz

Screen Components

You can also adjust USB in the INPUT menu.

DEVICE USB A USE TO

75

USB A USE TO

??? When playing music files

1

Select the target folder or drive.

2

Select the desired music title.

3

Music files are played.

???Use the P button to navigate up/down in the music page.

DEVICE

Using the remote control

YELLOW A method to view in 5 large thumbnail or simple list.

BLUE Convert to Mark Mode.

Return to normal TV viewing.

1

Select the target folder or drive.

2

Select the desired music title.

3

BLUE or Convert to Mark Mode.

4

Mark desired music file.

5 RED Marked music file is played.

???When one or more music files are marked, the marked music title will be played in sequence. For example, if you want to listen to only one music repeatedly, just mark the music only and play it. If no music is marked, all the music in the folder will be played in sequence.

???If you want to activate Random playback, you must set Option->Set audio play.->Random to On.

DEVICE USB A USE TO

Using the Music List function, play

NOTE

???Option values changed in Movie List does not affect Photo List and Music List.

???Option value changed in Photo List and Music List are changed likewise in Photo List and Music List excluding Movie List.

DEVICE USB A USE TO

DEVICE USB A USE TO

Using the remote control

???Stop the playing music file.

???Press the PLAY(???) button to return to normal playback.

When you press the Pause(II) button while playing the file, the playback will be

IIpaused.

When you press the Pause(II) button again while the playback is paused, it will resume the playback.

When playing,

??????/ ?????? When you press the REW(??????) button, the previous music file will be played.

When you press the FF(??????) button, the next music file will be played.

or

1

2

Select Repeat or Random.

Make appropriate adjustments.

DEVICE USB A USE TO

82

???If you don't press any button for a while during the playing, the play information box (as shown in the below) will float as a screen saver.

???The ???Screen Saver????

Screen saver is to prevent screen pixel damage due to an fixed image remaining on the screen for a extended period of time.

002. B02.mp3 ??? 00:31 / 04:04

NOTE

???A damaged or corrupted music does not play but displays 00:00 in playtime.

???A music downloaded from a paid service with copyright protection does not start but displays inappropriate information in playtime.

???If you press OK, ??? buttons, screen saver is stopped.

???The PLAY(???), Pause(II), ??? , ??????, ?????? buttons on the remote control are also available in this mode.

???You can use the ?????? button to select the next music and the ?????? button to select the previous music.

DEVICE USB A USE TO

83

You must register your device to play DivX protected videos. Registration code : **********

Register at http://vod.divx.com

Close

DEVICE USB A USE TO

3

Display DivX Reg. Code.

??? Press the MENU/EXIT button to return to normal TV viewing.

ABOUT DIVX VIDEO: DivX?? is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified?? device must be reg- istered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.

???DivX Certified to play DivX video up to HD 1080p, including premium content???

???Pat. 7,295,673; 7,460,668; 7,515,710; 7,519,274???

NOTE

Deregistration code :

********

Deregister at http://vod.divx.com Continue with registration?

USB A USE TO

3

Select Yes.

4

Display Deactivation.

DEVICE

MODE) DIGITAL GUIDE)(IN PROGRAMME (ELECTRONIC EPG

86

This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options.

The EPG supplies information such as programme listings, start and end times for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster).

This function can be used only when the EPG information is broadcast by broadcasting companies. You must set the Clock in the Time menu, before using EPG function.

The EPG displays the programme details for 8 days.

Talk show host Tyra Banks sits down with Keyshia Cole, the cast of Gossip Girl and Rihanna.

Talk show host Tyra Banks sits down with Keyshia Cole, the cast of Gossip Girl and Rihanna.

A pop-up window for record/remind settings appear.

Select Timer Record/Remind setting mode.

RED Change EPG mode.

YELLOW Enter Manual Timer mode.

BLUE Enter Schedule List mode.

When ???Now??? is selected, it is moved to selected program and EPG disappears

When ???Next??? is selected, a reservation pop-up window appears.

Select NOW or NEXT Programme.

Select the Broadcast Programme.

Page Up/Down.

Programme Guide

???

???

or or Switch off EPG.

Select DTV or RADIO Programme.

Detail information on or off

MODE) DIGITAL GUIDE)(IN PROGRAMME (ELECTRONIC EPG

87

MODE) DIGITAL GUIDE)(IN PROGRAMME (ELECTRONIC EPG

Button Function in 8 Day Guide Mode

RED Change EPG mode.

GREEN Enter Date setting mode.

YELLOW Enter Manual Timer mode.

BLUE Enter Schedule List mode.

When ???Currently broadcasting programme is selected, it is moved to selected pro- gramme and EPG disappears

When ???Future broadcasting programme is selected, a reservation pop-up window appears.

Select Programme.

Select the Broadcast Programme.

Programme Guide

Select DTV or RADIO Programme.

Detail information on or off

Button Function in Date Change Mode

GREEN or or Switch off Date setting mode.

Change to the selected date.

Select a date.

Programme Guide

Button Function in Extended Description Box

The detail information on or off.

Text Up/Down.

Select Timer Record/Remind setting mode.

Fia World Touring Car Chanpionship

Tue. 25 Nov. 2008 10:05 12:40

Fia Champion

Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp;

MODE) DIGITAL GUIDE)(IN PROGRAMME (ELECTRONIC EPG

89

Switch off Manual Timer mode.

Select Remind or Record function setting.

Select Type, Start Time, End time or

Programme.

YELLOW Change to Guide mode.

BLUE Change to Schedule List mode.

Manual Timer

MODE) DIGITAL GUIDE)(IN PROGRAMME (ELECTRONIC EPG

Save Timer Record/Remind.

YELLOW Change to Manual Timer mode.

Switch off Schedule List.

Select your desired Option(Modify/Delete/ Delete All).

Select programme.

Page Up/Down.

Schedule List

MODE) DIGITAL GUIDE)(IN PROGRAMME (ELECTRONIC EPG

91

1

2

Select Aspect Ratio.

Select the desired picture format.

???You can also adjust Aspect Ratio in the

PICTURE menu.

???For Zoom Setting, select 14:9, Zoom and Cinema Zoom in Ratio Menu. After com- pleting Zoom Setting, the display goes back to Q.Menu.

CONTROL PICTURE

Original

??? Just Scan

Following Selection will lead to you view the picture of best quality without loss of original picture in high resolution image.

Note : If there is noise in original Picture, You can see the noise at the edge.

??? Full Wide

When TV receives the wide screen signal,it will lead you to adjust the picture horizontally or vertically, in a linear proportion,to fill the entire screen fully.

4:3 and 14:9 video is supported in full screen without any video distortion through DTV input.

??? 4:3

The following selection will allow you to view a picture with an original 4:3 aspect ratio.

??? 14:9

You can view a picture format of 14:9 or a general TV programme in the 14:9 mode. The 14:9 screen is viewed in the same way as in 4:3, but is moved to the up and down.

??? Zoom

The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped.

??? Cinema Zoom

Choose Cinema Zoom when you want to enlarge the picture in correct proportion.

Note:When enlarging or reducing the picture, the image may become distorted.

??? or ??? button: Adjust enlarge proportion of Cinema Zoom. The adjustment range is 1 to 16. ??? or ??? button: Move the screen.

CONTROL PICTURE

Picture Wizard

With Picture Wizard, you can adjust the picture quality of the original image.

??? ???

CONTROL PICTURE

1

2

3

4

5

Select PICTURE.

Select Picture Wizard.

Adjust Standard(Black Level,

White Level, Tint, Colour, Horizontal Sharpness, Vertical Sharpness, Backlight) or

Preferred(Black Level, White Level, Tint, Colour, Sharpness, Dynamic Contrast, Colour Temperature, Backlight).

Select input source to apply the settings.

???If you stop the setting before the final stage, the changes will not be applied

???The adjustment value is saved to Expert1.

???Once the Picture Wizard sets the image quality, the Energy Saving is changed into Off.

???If the picture quality setting of Expert1 is changed, use the Picture Reset before entering the Picture Wizard to reset the picture quality setting.

???Standard : mode to set standard picture quality.

???Preferred : mode to set user preferred picture quality rather than standard pic- ture.

1

2

Select PICTURE.

Select Energy Saving.

CONTROL PICTURE

Game

??? ???

CONTROL PICTURE

1

2

Expert1

Expert2

Select PICTURE.

Select Picture Mode.

MANUAL PICTURE ADJUSTMENT

Picture Mode-User option

Backlight

To control the brightness of the screen, adjust the brightness of LCD panel.

Adjusting the backlight when setting the brightness of the set is recommended.

Contrast

Adjusts the signal level between black and white in the picture. You may use Contrast when the bright part of the picture is saturated.

Brightness

Adjusts the base level of the signal in the picture.

Sharpness

Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image.

Colour

Adjusts intensity of all colours.

Tint

Adjusts the balance between red and green levels.

Colour Temp.

Adjust to left direction to make a picture reddish or adjust to right direction to make a picture bluish.

It is not available to use this function in ???Intelligent Sensor??? (Only 32/42/46/52/60LD5***, 32LE3***, 32/37/42LE4***, 32/37/42/47/55LE5***).

??? Expert1

??? Expert2

PICTURE

1

2

3

4

Select PICTURE.

Select Picture Mode.

Select Vivid, Standard, Cinema, Sport or Game.

Select Backlight, Contrast, Brightness, Sharpness, Colour, Tint or Colour Temp..

??? Benefits of using Backlight

-The electricity consumption is reduced by up to 60 %.

-The black brightness is reduced. (As the black has greater depth, you can enjoy a better quality definition.)

-You can adjust brightness with maintaining original signal resolution.

CONTROL

5

Make appropriate adjustments.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

NOTE

???You cannot adjust colour, sharpness and tint in the RGB-PC/HDMI-PC mode.

???When the Expert 1/2 is selected, you can select Backlight, Contrast, Brightness, H Sharpness, V

Sharpness, Colour or Tint.

Downloaded From TV-Manual.com Manuals

97

CONTROL PICTURE

98

You can calibrate the screen for each Picture Mode or set the video value according to the special video screen.

You can set the video value differently for each input.

To reset to the factory default screen after making adjustments to each video mode, execute the ???Picture Reset??? function for each Picture Mode.

Image shown may differ from your TV.

Close

Digital Noise Reduction, Gamma, Black Level, Eye Care, Real Cinema, Colour Gamut or xvYCC. (Refer to p. 100 to 101)

4

Make appropriate adjustments.

???Press the MENU/EXIT button to return to normal TV viewing.

???Press the BACK button to move to the previous menu screen.

1

2

3

4

5

???

Close

Select PICTURE.

Select Picture Mode.

Select Expert1 or Expert2.

Select Expert Control.

Select your desired Source.

CONTROL PICTURE

CONTROL PICTURE

Dynamic Contrast (Off/Low/Medium/High)

Dynamic Colour

(Off/Low/High )

Skin Colour

(-5 to 5)

Noise Reduction

(Off/Low/Medium/High/ Auto(In Analogue Mode Only))

Digital Noise Reduction (Low/Medium/High/Off)

Gamma

(Advanced Control:

Low/Medium/High

Expert Control:

1.9/2.2/2.4 )

Black Level (Low/High/Auto)

Clear White (Off/Low/High)

Eye Care (Low/High/Off)

Real Cinema

(On/Off)

???Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker.

???Adjusts screen colours so that they look livelier, richer and clearer. This fea- ture enhances hue, saturation and luminance so that red, blue, green and white look more vivid.

???Adjusts skin colour of the picture so that user can set his favourite skin colour.

???Reduces screen noise without compromising video quality.

???Reduces noise regarding MPEG compressed video.

???You can adjust brightness of dark area and middle gray level area of the picture.

???Low/1.9 : Makes dark and middle gray level area of the picture brighter.

???Medium/2.2 : Expresses original picture levels.

???High/2.4: Make dark and middle gray level area of the picture darker.

???Low : The picture of the screen gets darker.

???High : The picture of the screen gets brighter.

???Auto : Sets black level of the screen to High or Low automatically according to the input signal level.

???Set black level of the screen to proper level.

???This function enables to select 'Low' or 'High' in the following mode: AV(NTSC-M), HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.

???Makes the white area of the screen brighter and clearer.

*This feature is not available for all models.

???Adjusts the brightness of the screen automatically to the best level for eyes when the screen is too bright.

???This feature is disable in ???Picture Mode-Vivid, Cinema, Expert1, Expert2,

Intelligent Sensor(Only 32/42/46/52/60LD5***, 32LE3***, 32/37/42LE4***, 32/37/42/47/55LE5***)???.

???You can watch a cinema-like video by eliminating judder effect.

???Use this function when you watch film-originated movie contents.

???This function can work when TruMotion is off.

Colour Gamut

(Advanced Control:

Wide/Standard)

Colour Gamut

(Expert Control: EBU/

SMPTE/BT709/Wide/

Standard)

Edge Enhancer

(Off/Low/High)

xvYCC (Auto/off/on)

Expert Pattern (Off/Pattern1/Pattern2)

Colour Filter (Off/Red/Green/Blue)

Colour Temperature (Medium/Warm/Cool)

Colour Management

System

???Standard : Mode to use original colour area regardless of the display char- acteristics.

???Wide: Mode to use maximum colour area of the TV display.

??? Maximize the utilization for colour area that can be expressed.

???Standard : Mode to use original colour area regardless of the display char- acteristics.

???Wide : Mode to use maximum colour area of the TV display.

???EBU : Mode to display EBU colour area.

???SMPTE : Mode to display SMPTE colour area.

???BT709 : Mode to display BT709 colour area.

???Makes the edge of the picture clearer and distinctive.

???This function can use in ???Picture Mode-Expert.???

*This feature is not available for all models.

???This is the function to express richer colour.

???This function is enabled in "Picture mode - Cinema, Expert" when xvYCC sig- nal is inputted through HDMI

???This is the pattern necessary for checking the picture of Digital TV.

???This function is enabled in "Picture Mode - Expert" when you watch DTV.

???This is the function to filter the specific colours of the video.

You can use the RGB filter to set colour saturation and hue accurately.

This is the function to adjust the overall colour of the screen to the feeling you want.

a.??? Method : 2 Points

???Pattern: Inner, Outer

???Red/Green/Blue Contrast, Red/Green/Blue Brightness:

The adjustment range is -50 to +50.

b.??? Method : 10 point IRE

???Pattern: Inner / Outer

??? IRE (Institute of Radio Engineers) is the unit to display the size of the video sig-

nal and can be set among 10, 20, 30 to 100. You can adjust Red, Green or Blue according to each setting.

???Luminance: This function displays calculated luminance value for 2.2 gamma. You can input luminance value you want at 100 IRE, than the target luminance value for 2.2 gamma is displayed at every 10 steps from 10 IRE to 90 IRE.

???Red/Green/Blue: The adjustment range is -50 to +50.

???As the tool used by the experts to make adjustments by using the test pat- terns, this does not affect other colours but can be used to selectively adjust the 6 colour areas (Red/Green/Blue/Cyan/Magenta/Yellow).

Colour difference may not be distinctive even when you make the adjust- ments for the general video.

??? Adjusts Red/Green/Blue/Yellow/Cyan/Magenta.

???Red/Green/Blue/Yellow/Cyan, Magenta Colour : The adjustment range is -30 to +30.

???Red/Green/Blue/Yellow/Cyan/Magenta Tint : The adjustment

range is -30 to +30.

??? This feature is disable in RGB-PC and HDMI (PC) mode.

CONTROL PICTURE

101

??? TruMotion

??? Screen

G

C

??? ???

??? TruMotion

??? Screen