WARNING - When using the dishwasher,

follow basic precautions, including the following: Read all instructions before using the dishwasher

o Use the dishwasher only for its intended function

o Use only detergents or rinse agents recom- mended for use in a dishwasher and keep them out of the reach of children.

When loading items to be washed:

1)Locate sharp items so that they are not/keiy to damage the door seal; and

2)Load sharp knives with the handles up to reduce the risk of cut-type injuries??

Do not wash plastic items unless they are marked "dishwasher safe" or the equivalent. For'plastic items not so marked, check the manufacturer's recommendations.

Do not touch the heating element during or immediately after use

o Do not operate the dishwasher unless all enclo- sure panels are properly in place.

Do not tamper with controls.

o Do not abuse, sit on, or stand on the door or dish racks of the dishwasher.

oTo reduce the risk of injury, do not allow children to play zn or on the dishwasher.

o Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the dish- washer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

o Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.

o Hot water fills the dishwasher to a level near the bottom of the overfill protector.

o Detergent is added at the correct times from the detergent dispenser, and hot water is pumped through the ULTRA WASH pump.

o Food particles are removed from dishes, pots and pans, tableware, and cutlery as the dish- washer sprays a mixture of hot water and detergent through two spray arms against their soiled surfaces.

o Water is pumped again through the ULTRA

WASH pump to remove soil particles from the water.

Water flushes

trapped particles out through drain

o Soil in the ULTRA WASH Soil Removal System is disposed down the drain with the wash water..

Final rinse water is heated, and a rinse agent is added to prepare the dishes for drying,

o Fresh, hot water enters the dishwasher, sprays on the dishes to rinse them, and rinse water is

pumped through the ULTRA WASH System to remove any remaining soil.

The rinse ends with the soil that is held in the ULTRA WASH Soil Removal System being disposed down the drain with rinse water.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

For a grounded, cord connected dishwasher:

The dishwasher must be grounded, In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current?? The dishwasher is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropri-

ate outlet that is installed and grounded in accordance with all local codes and ordinances.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in terminal box.

Do not use an extension cord.

Failure to do so can result in death, fire, or electrical shock.

WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock, Check with a qualified electrician or service representative if you are in doubt whether the dishwasher is properly grounded_ Do not modify the plug provided with the dishwasher; if it will not fit the outlet, have a proper outlet installed by a qualified electrician_

o For a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal, permanent wiring system, or an equipment- grounding conductor must be run with the circuit conductors and connected to the equipment- grounding terminal or lead on the dishwasher

NOTE: PF will show on the display the first time your dishwasher is connected to electricity or when electricity returns after prolonged failure. To clear the display, press the Cancel/Drain pad,

t, The ULTRA WASH TMSoi! Removal System is designed to remove food particles from the wash and rinse water, You only need to remove large chunks and bones

2, Properly load the top rack, bottom rack, and silverware basket,, See pages 13-17

3_ Spin both spray arms with both racks pushed back into place to make sure nothing prevents arms from turning freely,

4, Add detergent?? See page 11.

5. Check the rinse agent dispenser. See page 12, 6, Push door firmly when closing and it wilt

automatically latch

7.Run hot water at the sink nearest to the dish- washer until water is hot Turn off water.

Cancel/Drain

To change a cycle:

o During the first two minutes of operation while filling, simply select a new cycle.

OR

Automatic Preprogramming

Any option can be automatically preprogrammed by pressing and holding the desired option pad. The pad will beep when you first press it, then beep a second time while you continue to press ito Release the pad after the second beep. The option will automatically be chosen whenever you select a cycle with which the option normally works. To turn off a preprogrammed option, press and release the option pad, then press and hold the option pad until the pad beeps a second time..

o After the first two minutes, press Cancel/Drain, wait two minutes, and select a new cycle. (Remember to add detergent if the dishwasher has already gone through the wash portion of the cycle,)

Water Heat

Use this option when washing heavily soiled dishes. When you select Water Heat, the main wash will delay until the water heats to 135??F (57??C). As water heats, washing action will continue and the Water Heat light will glow; however, the electronic time display will pause.

o The Pots Pans cycle automatically uses Water Heat. o Selecting the Water Heat option will not cause water to be heated during Quick Rinse or China Ught cycle&

='t

!

;i

;4

:2:)::

!

No Heat Dry

Use this option to dry dishes in room temperature air and save energy When you select No Heat Dry, drying will take longer than heat drying, and water spotting can occur.. It is important to use rinse agent when selecting this option??

=Use this option when you do not plan to unload the dishwasher for several hours.

Sani Rinse

Sani Rinse is available in Pots Pans, Normal Wash, and Water Miser cycles.. When this option is selected, water for the final rinse is heated to ensure a high temperature, sanitary rinse. The cycle time will be extended until the water reaches the proper tempera-

ture. The Water Heat light glows and washing action continues while the water heats.. The Sani

Complete light glows at the end of the cycle indicating a high temperature, sanitary rinse was completed.

Cancel/Drain

When this option is selected, the dishwasher will stop and any water in it wilt drain. Draining will take about two minutes?? When draining is complete, all signals will turn off. You may then select a new cycle, if you wish..

i I-_:_L

NOTE: A flashing Sani Complete light indicates that a high temperature, sanitary rinse was not completed, The Sani Complete light will flash at the end of the cycle if the dishwasher door is opened, power fails, or water heating is not completed

during the final rinse, You may need to turn your water heater temperature up so water is at least 120??F (49??C) as it enters the dishwasher,

:;t;

i !i

$ig sal " ??

, ,un,,

Water Heating

The Water Heating fight glows to indicate the dish- washer is heating water to the proper dishwashing temperature if your household water is not hot enough NOTE: The electronic time display will pause whife this occurs??

o All cycles (except Quick Rinse) automatically heat water during the final rinse.

Water heating is automatic in the wash portions of the Pots Pane cycle,

Water heating is an option in the main wash of the Norma! Wash and Water Miser cycles,

#etaj ??atasi l??ast

...................lU,

Use Delay Wash when you want a cycle to start later, Delay Wash can be set to start the dishwasher during times when off-peak utility rates are in effect or when you are away from home

'1. Close the door firmly until you hear it latch..

2. Press the Delay Wash pad and one hour of delay will show on the display. Each time you press the Delay Wash pad, the delay time will increase in one-hour settings,, The longest delay setting

is 9 hours.,

Hours of delay

3. Press pads for desired cycle and options.

i Ul,, ii,,,,ll

In addition to showing remaining delay or cycle time, the digital display will show a code indicating the dishwasher's condition:

?? PF will appear in the display the first time the dishwasher is connected to the elec-

trical supply after inetallation_ This display also indicates there was a power failure. Press Cancel/Drain to

drain the dishwasher. If there is no water in the dishwasher, press Cancel/Drain a second time, Reselect a cycle to restart the dishwasher.

Sani Complete

The Sani Complete light glows at the end of the cycle indicating a high temperature, sanitary rinse was completed??

NOTE: A flashing Sani Complete light indicates that a high temperature, sani- tary rinse was not completed, The Sani Complete light will flash at the end of

the cycle if the dishwasher door is opened, power fails, or water heating is not completed during the final rinse. You may need to turn your water heater temperature up so water is at least 120??F (49??C) as it enters the dishwasher.

4_ The display will show the number of hours remain- ing until washing begins. The display will show hours only: If the display shows 2, there is be- tween 1 hour and 1 hour 59 minutes remaining.,

&When the hours of delay you have set have elapsed, the dishwasher will start the cycle se- lected in Step 3oThe wash time wi!l count down the minutes remaining in the cycle to O.

If you wish to put more dishes in the dishwasher

while it is in the delay mode, be sure to latch the door after adding them The timer wil! not advance unless the door is latched. To cancel Delay Wash, press the CanceVDrain pad.

?? CC will appear on the display when the dishes are washed and the cycle completed, Opening the door or pressing the Cancel/Drain pad wifl dear the display.

E2 witl appear in the display if the selector pads are stuck. Press CanceVDrain to release

the controls, or run your fingers across the pads to free them up. If E2 remains in the display, call for service.

HOTE: It is normal for cover to open partially when dispensing detergent.

How much detergent to use

o The amount of detergent to use depends on the hardness of your water and the type of detergent If you use too little, dishes won't be clean?? If you use too much in soft water, glassware wilt etch,

o Different brands of dishwasher detergent have different amounts of phosphorus for softening water. ]f you have hard water and use a detergent with a phosphorous content of less than 8.7%, you may need to use more detergent, or use a

detergent with a phosphorous content higher than 8_7%.

o Find out your water's hardness by asking your local water department or water softener company.

NOTE: Fill amounts shown are for standard pow- dered detergent, Amounts may vary if you use liquid or concentrated powdered detergent,. Follow manufacturer's directions when using liquid dishwasher detergent or concentrated powdered detergent.

Keep the rinse agent dispenser filled with a liquid

rinse agent. A rinse agent greatly improves dish drying by helping water flow off them during the last rinse, A rinse agent also keeps water from forming droplets and drying as spots or streaks??

To check dispenser:

o Check center of fill indicator cap. Clear means it needs filling,

A small amount of rinse agent automatically releases into the rinse water during the final rinse of each cycle. For best drying results, check dispenser periodically

to see if it needs filling.

o Or remove fill indicator cap. An "E" is visible at the bottom of the dispenser when empty,

Hot water dissolves and activates the dishwashing detergent. Hot water also dissolves grease on dishes and helps dry glasses spot-free, Use the Water Heat option, if available, if you keep your water heater at a low setting. For best dishwashing results, water must be at least 120??F (49??0) as it enters the dishwasher.

NOTE: The time showing on the electronic display will pause while water is heating, For more infor- mation, see "Dishwasher seems to run too long" on page 26.

To check water temperature:

1oRun hot water at the faucet closest to your dish- washer?? Let the water run for at least 1 minute.

2. Measure the water temperature with a candy or meat thermometer,, Put the thermom- eter in the running stream of water.

3.If the water temperature at the faucet is below 120??F (49??C), have a qualified person raise the water heater's thermostat setting.

Adjustable top rack

You can raise or lower the rack to fit tall items in

Utensil basket

Use this convenient basket to hold spatulas, wooden spoors, and

over the front of the

similar items. It hooks top rack and is not

_%_%_._0 =o..,>".._ removable.

Cup and glass toad

Extra-capacity fold-down shelves

Fold down the extra shelves on the right side of the top rack over short items (cups, juice glasses, cereal bowls, etc.) to hold extra items. Adjust rack height if necessary (see "Adjustable top rack" left),

Fold-down tines

Fold the tines in the top rack all the way down to accommodate

larger items.

............................i .. H..I..,..I

o Load items so they do not block or cover the spray tower

o Make sure pot handles and other items do not stop rotation of the iower spray arm_ The spray arm must move freely.

o When the bottom rack is removed, replace with bumpers in front.

FoUd-down divider

A fold-down divider at the back of the rack can be Iowered to make room for deep bowls,

roasters, etc

Mixed load

Spray tower

....................................................

o Load the silverware basket while it is in the bottom rack or take the basket out for loading on a counter or table.

NOTE: You can remove the basket for easy unloading?? Always unload or remove the basket before unloading the racks to avoid spilling water droplets on the silverware??

???Place small items (baby bottle caps, jar lids, etc.)

in the section next to the hinged cover. Close the cover over the section to hold small items

in place.

Mix items in each section of the basket with some pointng up and some down to avoid nesting. Spray cannot reach nested items.

iMPORTANT: Always load sharp items (knives, skewers, forks, etc.) poinfng down

To avoid thumping and clattering noises during operation:

Make sure lightweight load items are secured in the racks.

o Make sure pot lids and handles, pizza pans, cookie sheets, etc.., do not touch interior walls or interfere with the spray arm's rotation or cover the spray tower.

i

Section cover

o Load dishes so they do not touch one another.

NOTE: Keep sink drain plugs inserted during dish- washer operation to prevent noise transfer through drains..

Cleaning the exterior

In most cases, regular use of a soft, damp cloth or

sponge and a mild detergent is al! that is

necessary to keep the outside of your dish-

washer nice looking and clean,

Cleaning the interior

Hard water minerals may cause a white film to build up on the inside surfaces,

especially just beneath the door area. To clean

interior:

_Apply powdered dish- washer detergent to a damp sponge to make a paste,

OR

oUse liquid automatic dishwasher detergent

and clean with damp sponge

Do not clean the dishwasher interior until it has cooled.

Wear rubber gloves. Do not use any type of cleanser other than dishwasher detergent because it may cause foaming or sudsing.

NOTE: Some tomato-based foods might permanently stain the inner tub and door liner. It is recommended

that you prerinse concentrated amounts of soil from the dishes before loading.

Moving or winterizing your

dishwasher

Protect your dishwasher and home against water damage due to freezing water lines. If your dish- washer is left in a seasonal dwelling or could be exposed to near freezing temperatures, have a qualified person do the following:

1.Disconnect power supply to the dishwasher.

2.Turn off water supply to the dishwasher.

3.Remove the 4 screws on the lower access panel and remove the tower access panel,

4.Place a shallow pan under the water supply valve. Then, use a wrench to disconnect the water inlet from the water supply valve, Sepa- rate the water inlet from the water supply valve and drain water into the pant

5.Remove the spring clamp from the water outlet and separate from the water supply valve; drain water into pan,

/

continued on next page

Reconnecting your dishwasher

1.Remove the 4 screws on the lower access panel and remove lower access panel,

2.Turn on the water supply to dishwasher.

3.Turn on power supply to dishwasher.

4, Run dishwasher through a complete cycle and check for leaks,

5. Replace lower access panel,

NOTE: If your dishwasher is connected to a garbage disposal, do not run water into the sink after winterizing, This could cause water to refill the drain hose on your dishwasher.

N

Water supply Water Drain valveinlethose

You can help save energy if you;

??Wash full loads, Running a half-filled dishwasher uses the same amount of electricity and hot water as a fully loaded machine,

??Use the Water Miser cycle if dishes are prerinsed. The cycle uses Jess hot water and energy than the Normal Wash cycle.

o Use the No Heat Dry option when you don't need a rapid drying cycle. Allow longer drying times (overnight) Use a rinse agent to improve drying.,

??Use the Water Heat option only when needed. When this option is off, the dishwasher will not pause to heat water to 135??F (57??C) during the main wash.,

NOTE: Loads may not wash as welt if the water temperature is too low.

Load correctly for best washing results. Incorrect loading may cause poor washing and the need to rewash all or part of the loado

Use the delay feature to run your dishwasher during off-peak hours. Local utilities recommend this to avoid heavy usage of energy at certain times of day.

i ii i II'l'M'llllm'lllllllll.I

NOTE; See your Installation Instructions for more complete information on changing door color panels or installing customized wood panels??

The opposite side of the door panel is a different color, Additional colors are available through Sears Repair Services (see page 27)??

Customized wood panels

Your dishwasher can be customized with wood

panels, A heavy-duty door spring kit (Part No, 4318050) is needed if the upper panel weighs more than 4 pounds. The maximum weight for the upper panel and door is 8 pounds

Upper panel

t. Insert a finger under one end of the retainer, Pull the retainer towards you

in a peeling action. Set retainer aside

2, Lift color panels at outer edges. Use one hand to

???bow bottom of panel

Do not remove spacer,

Remove color panel(s)_

5, Push in on color panel(s) near the top and slide panel(s) and spacer up inside bottom of control

panel. Let color panel(s) rest on channel at bottom of doors.

3, With desired color facing out, insert one side of

color panel into door frame,.

4, Bow color panel and insert other side into

!door frame..

panel

Channel

2. Carefully slide access oanel upward and remove. Do not remove spacer.

4.Make sure access panel has slid into groove along bottom of access panel frame.

5.Line up edges of top trim with sides of access

panel frame. Tilt back of trim down and slide into placer Snap front of trim down to cover top edge of access panel,

PROBLEM

Food soil left on dishes

Spotting and filming

CAUSE

Improper loading

Water temperature is too low

Use of incorrect,

too little, or ineffective detergent

Detergent cakes in dispenser

Pump or spray arm clogged by labels from bottles and cans

Low water pressure caused by insufficient fill

Slowdown of wash arm due to high suds

Hard water or high mineral content in water

Water temperature is too low

Use of incorrect detergents

Incorrect amount of detergent

Use of ineffective detergents

SOLUTION

Follow loading instructions on pages 13-17o

Use the Water Heat option.. If needed, turn home water heater up to ensure water entering dishwasher is 120??F (49??C) minimum See "Water temperature tips" on page 12.

Use recommended dishwasher detergents onlyo Follow recommendations on page 11 for amounts; never use less than 1 tablespoon per load. Deter- gent must be fresh to be effective. Always store detergent in a cool, dry area.

Use fresh detergent only. Do not allow detergent to sit for several hours in a wet dispenser. Check dispenser for caked detergent?? Clean dispenser when caked detergent is present.

Remove labels before washing bottles and cans or wash by hand?? See page 18.

Home water pressure should be 20 to 120 pounds per square inch (psi) for proper dishwasher fill. A booster pump on the water supply may be neces- sary if pressure is too low.

Never use soap or laundry detergents. Use recom- mended dishwasher detergents only.

Conditioning the final rinse water with a liquid rinse agent helps eliminate spotting and filming. Keep the dispenser full with a rinse agent at ail times.

Use the Water Heat option, if available.. If needed, turn home water heater up to ensure water entering dishwasher is 120??F (49??C) minimum. See "Water temperature tips" on page 12.

Use recommended dishwasher detergents oniy

Follow recommendations on page 11 for amount, Heavy soil and/or hard water generally require extra detergent.

Detergent should be fresh. Store in a cool, dry place, preferably in an airtight container. Discard lumpy detergent..

PROBLEM

Spotting and filming (cont.)

Cycle takes

extremely long time

Dishes do not dry completely

Silica film or

etching (silica film is a white iridescent

deposit; etching is

a cloudy film)

Black or gray marks on dishes

Brown stains on dishes and dishwasher interior

CAUSE

Insufficient fill caused by tow water pressure

Water temperature is too low

Dishes do not drain properly

Plastics

Rinse agent dispenser is empty

A water chemical reaction with certain types of glassware.

Usually caused by some combination of

soft or softened water, alkaline washing solutions, insufficient

rinsing, overqoading the dishwasher, and

heat of drying.

Aluminum items

High iron content in water supply

SOLUTION

Home water pressure should be 20 to 120 psi for proper dishwasher fill. A booster pump on the water supply may be necessary if pressure is too low

NOTE:To remove spots and film from dishes, try a vinegar rinse

1.Wash and rinse as usual using the Air Dry option.

2.Remove a!f metal items

3.Put 2 cups (500 mL) white vinegar in a container on the bottom rack.

4.Run dishwasher through complete washing cycle_ Vinegar will mix with wash water??

If needed, turn home water heater up to ensure water entering dishwasher is 120??F (49??C) minimum. See "Water temperature tips" on page t2.

Dishes must have proper water drainage. Do not overload. Follow instructions for loading dishwasher on pages 13-17 Use a liquid rinse agent to speed drying

Some plastics, due to material, may need to be towel dried.

Fit! rinse agent dispenser, See page 12.

It may not be possible to prevent problem, except by hand washing. To slow this process, use a minimum amount of detergent but not less than

1 tablespoon per load. Use a liquid rinse agent and underload the dishwasher to allow thorough rinsing. Silica film and etching are permanent and cannot be removed. Use the Air Dry option_

Aluminum items should be loaded so that they will

not rub against dishes during washing Throwaway aluminum items should not be washed in the dish-

washer because they may break down and cause marking, Aluminum markings can be removed by using a mild abrasive cleanser.

Remove by washing dishes (after food soil has been removed) with 1 teaspoon to 1 tablespoon of citric acid crystals added to covered section of detergent dispenser. Do not use detergent_ Follow with a Normal cycle with detergenL If treatment is needed

more often than every other month, the installation of an iron removal unit is recommended.