GR-AX46

ENGLISH

Dear Customer,

Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new camcorder.

Using This Instruction Manual

???All major sections and subsections are listed in the Table Of Contents (Z pg. 7).

???Notes appear after most subsections. Be sure to read these as well.

???Basic and advanced features/operation are separated for easier reference.

It is recommended that you . . .

...... refer to the Index (Z pgs. 39 ??? 42) and

familiarize yourself with button locations, etc. before use.

...... read thoroughly the Safety Precautions and Safety Instructions that follow. They contain extremely important information regarding the safe use of your new camcorder.

You are recommended to carefully read the cautions on pages 43 and 44 before use.

SAFETY

PRECAUTIONS

WARNING:

TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE

THIS UNIT TO RAIN OR

MOISTURE.

Warning on lithium battery

The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100??C (212??F) or incinerate. Replace the battery with Panasonic (Matsushita Electric), Sanyo or Maxell CR2025; use of another battery may present a risk of fire or explosion.

nDispose of used battery promptly.

nKeep away from children.

nDo not disassemble and do not dispose of in fire.

NOTES:

cThe rating plate (serial number plate) and safety caution are on the bottom and/or the back of the main unit.

cThe rating plate (serial number plate) of the AC Power Adapter/Charger is on its bottom.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The AA-V11U AC Power Adapter/Charger should be used with:

AC 120 V`, 60 Hz in the USA and Canada, AC 110 ??? 240 V`, 50/60 Hz in other countries.

CAUTION (applies to the AA-V11U)

TO PREVENT ELECTRIC SHOCK MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION (s???applique ?? l???AA-V11U)

POUR ??VITER LES CHOCS ??LECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE

DANS LA BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU???AU FOND.

This Class B digital apparatus meets all requirements of the Canadian Interference ??? Causing Equipment Regulations.

???Cet appareil num??rique de la classe B respecte toutes les exigences du R??glement sur le mat??riel brouilleur du Canada.???

This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for playback with a television of a different standard. However, live recording and viewfinder playback are possible anywhere. Use the BN-V11U/V12U/V22U/V25U battery packs and, to recharge them, the provided multi-voltage AC Power Adapter/Charger. (An appropriate conversion adapter may be necessary to accommodate different designs of AC outlets in different countries.)

ATTENTION:

The product that you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

IMPORTANT PRODUCT

SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this manual for future reference.

INSTALLATION

1. Grounding or Polarization

(A)Your product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B)Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.

If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

EN 3

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

???Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.

???Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer???s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION

INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

USE

1. Accessories

To avoid personal injury:

???Do not place this product on an unstable cart, stand, tripod, bracket or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

???Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.

???Use a mounting accessory recommended by the manufacturer and follow the manufacturer???s instructions for any mounting of the product.

???Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combina- tion to overturn.

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

3. Water and Moisture

Do not use this product near water???for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

PORTABLE CART WARNING (Symbol provided by RETAC)

3. Replacement Parts

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.

QUICK OPERATION GUIDE

SUPPLY POWER

Hook on.

1

2Push in.

BATT. RELEASE

Using the battery pack

1Hook-on the battery pack???s top end to the camcorder. (Charging procedure, Z pg. 8)

2Push in the battery pack until it locks into place.

To remove the battery pack

Slide BATT. RELEASE and pull out the battery pack.

EN 5

INSERTING A VIDEO CASSETTE

EJECT

1

1 Slide EJECT.

2 Insert a video cassette.

3 Press PUSH.

(For more details, Z pg. 12)

PLAYBACK

STOP

2REW

3

PLAY/PAUSE

1

Set to ???PLAY???.

1Set the power switch to ???PLAY???.

2Press REW.

???The tape will automatically stop at the beginning of the tape.

3Press PLAY/PAUSE.

???Playback starts and the playback picture appears in the viewfinder.

???To stop playback, press STOP. (For more details, Z pg. 30.)

nOr simply play back the tape on a VHS

VCR using the Cassette Adapter (VHS Playpak). Z pg. 28

SHOOTING

1

LENS COVER open/close knob

2

Set to ???CAMERA???.

3Recording Start/Stop button

1 Slide the LENS COVER open/close knob to open the lens cover.

2 Set the power switch to ???CAMERA???.

???The power indicator will light and an image will appear in the viewfinder.

3 Press the Recording Start/Stop button.

???Recording starts.

???To stop recording temporarily, momentarily press the Recording Start/Stop button once

again.

(For more details, Z pg. 14)

REMEMBER

The Logical Choice

Program Manager (Z pg. 16 ??? 27)

Program AE with Special Effects, Exposure Control, Focus, Fader, Wide, Instant Title, Date/Time Character Insert, White Balance Adjustment, Menu Adjustment

Variable-Speed Hyper Zoom (Z pg. 15)

Zoom-in

Program AE with Special Effects (Z pg. 16)

nAuto Mode Lock n Auto Mode Release

nElectronic Fog Filter n ND Effect

nSepia n Twilight n Sports

n1/1000 sec. High Speed Shutter

n1/2000 sec. High Speed Shutter

Zoom-out

Random Assemble Editing (Z pg. 33 ??? 35)

EN 7 STARTEDGETTING

EDITING PLAYBACK RECORDING

8EN

END indicator

Charge marker

** CHARGE MARKER

A charge marker is provided on the battery pack to help you remember whether it has been charged or not. Two colors are provided (red and black)???you choose which one means charged and which means discharged.

GETTINGSTARTED

Power

This camcorder???s 3-way power supply system lets you choose the most appropriate source of power.

NOTES:

cNo function is available without power supply.

cUse only specified power supply.

cDo not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

SUPPLY POWER

1 Connect the charger???s AC power cord to a wall outlet. The power indicator lights.

ATTACH BATTERY PACK

2 Align the marks and slide the battery pack in the direction of the arrow until it locks in place. The CHG. indicator lights.

DETACH BATTERY PACK

3 When charging is completed, the END indicator lights. Slide the battery pack opposite the direction of the arrow.

Hook on.

Push in.

BATT. RELEASE

ATTENTION:

Before detaching the power source, make sure that the camcorder???s power is turned off. Failure to do so can result in a camcorder malfunction.

USING THE BATTERY PACK

ATTACH BATTERY PACK

1 Hook its top end to the camcorder and push the battery pack in until it locks in place.

DETACH BATTERY PACK

2 Slide BATT. RELEASE and pull out the battery pack.

**REFRESH

The AC power adapter features a REFRESH function that allows you to fully discharge the battery pack before recharging.

To discharge the battery . . .

..... attach the battery pack to the adapter as shown in the illustration to the left. Then push REFRESH. The REFRESH indicator lights when discharging starts, and goes out when discharging is complete.

To AC outlet

DC OUT

terminal

To DC in jack

AP-V7U (optional)

Car Battery Charger/Adapter

BH-V3U (optional)

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery Charger/Adapter (connect as shown in the illustration to the left).

NOTES:

cWhen using the car battery, leave the engine idling.

cThe optional Car Battery Charger (BH-V3U) can also be used to charge the battery pack.

cWhen using the optional Car Battery Charger or Car Battery Cord (AP-V7U), refer to the respective instruction booklet.

USING AC POWER

Use the AC Power Adapter (connect as shown in the illustration to the left).

NOTE:

The supplied AC Power Adapter/Charger features automatic voltage selection in the AC range from 110 V to 240 V.

4

5

INSERT BATTERY

Ensuring the plus (+) side is up, insert a CR2025 lithium battery and push it in.

CLOSE COVER

Close the compartment cover until it clicks in place.

3

1

2

Set POWER to ???CAMERA???.

Viewfinder Adjustment

POSITION VIEWFINDER

1 Adjust the viewfinder manually for best viewability (see illustration at left).

SELECT MODE

2 Set the power switch to CAMERA.

ADJUST DIOPTER

3 Turn the diopter adjustment control until the indications in the viewfinder are clearly focused.

MENU

+

PROGRAM AE select dial

NEAR

END :MENU KEY

Set Time and

Date Screen

J A N 1 . 00 AM 12:00

SET

CANCEL

Date

Month/Day/Year

Time

12-hour indication with AM or PM

???If you decide you want to return the date and time to the previous settings, press FAR or NEAR to move the highlight bar to ???CANCEL???, then press

MENU.

???If you???re satisfied with the settings, go on to step 5.

START CLOCK OPERATION

5 Once you???ve set the month, day, year and time, press FAR or NEAR until ???SET??? begins to blink, then press MENU. The Menu screen reappears.

CLOSE MENU

6 Press MENU.

NOTES:

cTo display the date and time in the viewfinder and on a connected TV, see ???Date/Time Insert??? (Z pg. 22).

cIf, in step 4, you input an invalid date (FEB 30, JUN 31, etc.) and perform step 5, ???INPUT ERROR??? appears blinking at the bottom of the screen. Press +, ???, FAR or NEAR to input the correct number.

SP-EP recording mode button

Set POWER to ???CAMERA???.

Tape length indicator

Tape Length Setting

Set the tape length according to the length of the tape used.

SET TAPE LENGTH

1 Press T20???30???40 until the required indication appears in the veiwfinder. T20 = 20 minutes of recording time, T30 = 30 minutes, and T40 = 40 minutes (in SP).

NOTE:

The tape remaining time (Z pg. 14) displayed in the viewfinder is correct only if the correct tape length has been selected.

Recording Mode Setting

Set depending on your preference.

SET RECORDING MODE

1 Press SP???EP button. ???SP??? (Standard Play) provides higher picture and sound quality and is better for dubbing, while ???EP??? (Extended Play) is more economical, recording at 1/3 the speed of SP.

NOTE:

If the recording mode is switched during recording, the playback picture will be blurred at the switching point.

Recording mode indicator

Turn to take up slack.

Loading/Unloading A Cassette

OPEN CASSETTE HOLDER

1 Slide EJECT until the holder opens. Do not use force to open.

INSERT/REMOVE CASSETTE

2 Make sure the label is facing outward.

CLOSE CASSETTE HOLDER

3 Press PUSH and make sure the holder is closed and locked.

NOTES:

cA cassette holder can???t be opened unless a power supply is attached.

cMake sure that the tape is not slack when loading the cassette. If there is any slack, turn the gear on the cassette in the direction of the arrow to take up the slack.

cMake sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.

cThe cassette holder can???t be opened while the camcorder is in the record mode.

ATTACH STRAP

Following the illustration at left, thread the strap through the top of the eyelet 1, then fold it back and thread it through the keeper 2, and then through the buckle 3. Repeat the procedure to attach the other end of the strap to the other eyelet, making sure the strap isn???t twisted.

ADJUST LENGTH

Tape remaining time indicator

LENS COVER switch

POWER

Start/Stop button

Tally lamp

NOTE:

You should already have performed the procedures listed below. If not, do so before continuing.

cPower (Z pg. 8)

cTape Length setting (Z pg. 12)

cRecording Mode Setting (Z pg. 12)

cGrip Adjustment (Z pg. 13)

LOAD A CASSETTE

1 Slide EJECT to open the cassette holder, then insert the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked.

ENTER RECORD???STANDBY MODE

2 Slide the LENS COVER open/close switch to open the lens cover, then set the power switch to ???CAMERA???.

???The power indicator lights and the camcorder enters the Record???Standby Mode.

???The scene you???re aimed at appears on the viewfinder screen, with the word ???PAUSE??? superimposed upon it.

START SHOOTING

3 Press the RECORDING START/STOP button.

???The tally lamp lights while recording is in progress, and ???REC ??? appears in the viewfinder.

STOP RECORDING

4 Press the RECORDING START/STOP button again to stop recording.

???The camcorder re-enters the Record-Standby mode.

RECORDING Basic Features

Power zoom switch

Zoom-in

Zoom-out

Zoom indicator

RETAKE (R/F)

1 second later, the mode is activated.

SEPIA

After 1 sec.

Viewfinder

Program AE With Special Effects

All you have to do to access any of the variety of shooting effects is to turn the PROGRAM AE select dial.

SELECT MODE

1 Turn the PROGRAM AE select dial until the symbol of the function you want is aligned with the mark.

???The selected mode???s name and its indication are displayed in the viewfinder for approx. 1 second. Then the name disappears, and only the indication remains. The mode is activated.

???When Auto Mode Lock or Auto Mode Release mode is selected, only the mode???s name is displayed. Then the name disappears and the mode is activated.

NOTES:

cOnly one effect can be engaged at a time.

cThe screen becomes slightly reddish when the fader (Z pg. 20) is used in the Sepia mode.

cThe screen becomes slightly dark in the High Speed Shutter mode. Use in well-lighted situations.

cIn the High Speed Shutter or Sports modes, picture color may be adversely affected if subject is lit by alternating discharge-type light sources such as flourescent or mercury-vapor lights.

Auto Mode Lock

Locks the camcorder in Full Auto mode, preventing incorrect operation due to accidental button pressing during shooting.

???In this mode the following controls are disabled; FADE, WIDE, TITLE, DISPLAY, M.W.B (Manual White Balance), Manual Focus, Focus Lock, Exposure Control and MENU

Auto Mode Release

Re-enables the controls that were disabled by Auto Mode Lock.

Electronic Fog Filter

Makes the picture look misty white, as when an external fog filter is attached to the lens. Softens the image and gives it a ???fancy??? look.

ND Effect

A black mist darkens the picture, as when an ND filter is used. Helps to counter the effects of glare on the subject.

SEPIA Sepia

Sepia

The scene being shot is recorded in sepia-tinted (reddish-brown) monochrome, giving the effect of an older movie. Use together with Wide (Z pg. 20) for the authentic look of a classic Hollywood movie.

TWILIGHT Twilight

Twilight

Dusk, twilight scenery, fireworks, etc., look more natural and dramatic. The following happens when Twilight mode is selected:

???Auto gain control is turned off.

???White Balance is set to ?????? (outdoor mode), but

can also be manually changed to another mode (Z pg. 23).

???Auto Focus becomes available only in the range of 10 m to infinity. To focus when the subject-to-

camera distance is less than 10 m, use manual focusing (Z pg. 19).

+

+02

???Exposure Level Indicator

To brighten the image

To darken the image

EN 17

SPORTS Sports

Sports

High shutter speed clearly captures fast-moving action.

High-Speed Shutter (1/1000s., 1/2000s.)

Captures faster action than Sports mode.

Exposure Control

This feature automatically adjusts the iris for the best available picture quality, but you can override and make the adjustment manually.

SELECT MODE

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK.

BRIGHTEN IMAGE

2 Press + (maximum +06). The Exposure level indicator appears in the viewfinder.

OR . . .

DARKEN IMAGE

Press ??? (maximum ???06). The Exposure level indicator appears in the viewfinder.

When you want to return to the factory setting . . .

RESTORE INITIAL SETTING

3 Press + and ??? simultaneously. The standard setting is immediately restored and the Exposure level indicator disappears.

Focus

detection zone

PROGRAM AE select dial

Auto Focus

The camcorder???s Full Range AF system offers continuous shooting ability from close-up to infinity. However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing):

???When two subjects overlap in the same scene. ???When illumination is low.*

???When the subject has no contrast (difference in brightness and darkness), such as a flat, one-color wall, or a clear, blue sky.*

???When a dark object is barely visible in the viewfinder.* ???When the scene contains minute patterns or identical

patterns that are regularly repeated.

???When the scene is affected by sunbeams or light reflecting off the surface of a body of water.

???When shooting a scene with a high-contrast background.

*The low-contrast warning ?????? appears in the viewfinder.

Focus Lock

This feature locks the focus in place, which is especially helpful in the following situations:

???When things pass between your subject and the camcorder. Engage the focus lock function to lock your subject in before recording.

???When you want your subject to be focused, and to appear in a corner of the screen. First, center on the subject and focus using auto focus mode. Then engage the focus lock function and move the camcorder until the subject is where you want it.

Function indication

FADE

Fade-Standby indication FADE

SELECT button

PROGRAM AE select dial

SET button

FADE IN

Fader

This feature allows smooth fade-in and fade-out to black blank screen. Fade-in works at recording start, and fade-out works at recording end or when you enter Record???Standby mode.

SELECT MODE

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK.

SELECT FUNCTION

2 Press SELECT repeatedly until ??? FADE ??? appears.

ENGAGE FADE???STANDBY MODE

3 Press SET to engage the Fade???Standby mode. The Fade-Standby indication ???FADE??? is displayed.

START RECORDING

4 Press Recording Start/Stop to start recording and activate fade-in.

OR . . .

END RECORDING

Press Recording Start/Stop to end recording and engage fade-out.

Title indication

TITLE

HAPPY BIRTHDAY

OUR VACATION

MERRY CHRISTMAS

A SPECIAL DAY

No indication HAPPY HOLIDAYS

EN 21

Instant Titles

The camcorder has eight preset titles in memory. You can superimpose one of them above a previously stored title as shown in the illustration to the left.

DISPLAY

SELECT MODE

Turn the PROGRAM AE select dial to any position except

AUTO LOCK.

SELECT

OUR NEW BABY

WEDDING DAY

SELECT FUNCTION

TITLE ??? appears.

SET

CONGRATULATIONS

cTo erase a character you entered mistakenly, make ???CLEAR??? blink by pressing +, ???, FAR or NEAR, then press MENU. All characters are deleted at once. Or, to erase selected characters only, first move the pointer to the row of squares by pressing +, ???, FAR or NEAR to highlight them. Press FAR or NEAR to make the desired character blink, then press +, FAR or NEAR to move the pointer to ??? ??? in the top left corner. Press MENU.

cTo display the characters you have set ??? ???Instant Title??? or ???Date/Time/Character Insert??? (Z pg. 22).

cCharacters may be set only in the Record-Standby mode.

SET

Auto Date Record mode Date display

Date-off mode

Character Generator Date/Time display

Auto Date Record mode

Character Generator

This feature allows you to display date, time and characters in your viewfinder and on a connected color monitor, record them manually or automatically, and even make your own titles.

NOTE:

You should already have performed the Date/Time Setting procedure (Z pg. 11). If you haven???t, do so before continuing.

DISPLAY

SELECT MODE

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK.

SELECT DISPLAY

2 Press SELECT repeatedly until ??? DISP. ??? appears.

CHOOSE DISPLAY MODE

3 Press SET while in Record???Standby to cycle through the modes as shown in the illustration at left.

NOTES:

cThe selected display can be recorded.

cIf you don???t want to record the display, select Date-off mode before shooting.

cIf you want to delete the display during shooting, press

SET.

cIf you want to call back a deleted display, engage the Record???Standby mode and then select the desired display mode using SET.

AUTO DATE RECORD

Your camcorder automatically records the date for about 5 seconds after recording is initiated in the following situations:

???After changing the date. ???After loading a cassette.

???After Auto Date Record mode is selected by pressing

SE T.

In this mode, the date is replaced after 5 seconds with ???AUTO DATE???.

NOTES:

cSetting PROGRAM AE to LOCK always engages the auto date record mode, and disables all other modes.

cIn the Auto Date Record mode, if the date changes while you???re shooting, the date indication is recorded for about 5 seconds from that point. It is not recorded during any other recordings made on that day.

White balance mode indicator

MWB

SELECT

SET

PROGRAM AE select dial

EN 23

Manual White Balance Adjustment (M.W.B.)

This camcorder???s Automatic Color Temperature system senses the color temperature of the ambient lighting for automatic white balance adjustment. However, precise color adjustment is not possible under the following conditions:

???When an object is in various shades of the same color.

???When a predominantly red or brown object is being shot outdoors.

In these cases, use the camcorder???s built-in preset filters for white balance adjustment.

SELECT MODE

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK.

SELECT FUNCTION

2 Press SELECT reapeatedly until ??? M.W.B. ??? appears.

SELECT WHITE BALANCE

3 Press SET (Manual White Balance) until the required indication appears in the viewfinder.

???MWB??? ..... With a memorized personal White Balance setting (see below)

??? ??? ......... Outdoors on sunny day

??????......... Outdoors on cloudy day

?????? .......... Light source is halogen or tungsten lamp

MWB

1

2

SELECT MODE

Turn the PROGRAM AE select dial to any position except AUTO LOCK.

ADJUST FOCUS

Point the camcorder at a white, flat object such as a sheet of white paper, and adjust focus manually (Z pg. 19).

ADJUST WHITE BALANCE

+

SET CHARACTER

DATE/TIME

END :MENU KEY

PAUSE

This camcorder is equipped with Program Manager, an easy-to-use, on-screen menu system that simplifies many of the more detailed camcorder settings.

SELECT MODE

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK.

ACCESS MENU SCREEN

2 Press MENU.

SELECT FUNCTION

3 Press + or ??? to place the highlight bar on the desired function.

MAKE SETTING

4 The setting procedure depends on the function you select.

If you select GAIN UP, TELE MACRO, INTERVAL TIMER, REC TIME or JLIP ID NO. . . .

.... press FAR or NEAR to cycle through the choices until the desired setting appears.

If you select SET CHARACTER or DATE/TIME, . . .

.... press NEAR to access the selection menu for each function (SET CHARACTER ??? Z pg. 21; DATE/TIME ??? Z pg. 11).

CLOSE MENU

5 Press MENU. The normal screen reappears.

NOTE:

The menu is available only in the Record-Standby mode.

Animation

Give stationary scenes or objects an illusion of movement. This function allows you to shoot a series of pictures, each slightly different, of the same object for a brief period of time.

NOTE:

Make sure the camcorder is in the Record-Standby mode and the recording mode is set to ???SP??? before performing the following steps.

ACCESS MENU SCREEN

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK, then press

MENU.

SET RECORDING TIME

2 Press ??? or + to move the highlight bar down to ???REC TIME???, then press FAR or NEAR to cycle through the choices. Stop when the desired time appears. Choose from ???1/4S???, ???1/2S???, ???1S???, or select to turn the function ???OFF???. Then press MENU to close Menu screen.

START RECORDING

3 Press the Recording Start/Stop button after focusing on the subject. The recording stops automatically after the selected period of time.

ASSEMBLE SERIES OF

PICTURES

4 Repeat step 3 for the desired number of pictures.

RELEASE ANIMATION MODE

5 Set ???REC TIME??? in the Menu screen to ???OFF???.

NOTES:

cFor best results, make sure the camcorder is secured when shooting in Animation or Time-Lapse mode.

cFade-in/out cannot be performed during Animation or Time-Lapse shooting.

cBefore performing other operations following Animation or Time-Lapse recording, make sure the Animation or Time-Lapse mode is deactivated.

EN 27

Time-Lapse

You can record sequentially at preset time spans. Leaving the camcorder aimed at a specific subject, you can record subtle changes over an extended period of time.

NOTE:

Make sure the camcorder is in the Record-Standby mode and the recording mode is set to ???SP??? before performing the following steps.

ACCESS MENU SCREEN

1 Turn the PROGRAM AE select dial to any position except AUTO LOCK, then press

MENU.

SET INTERVAL BETWEEN

RECORDINGS

2 Press ??? or + to move the highlight bar down to ???INTERVAL TIMER???, then press FAR or NEAR to cycle through the choices. Stop when the desired time appears. Choose from ???15S???, ???30S???, ???1MIN???, ???5MIN???, or select to turn the function ???OFF???.

SET RECORDING TIME

3 Press ??? or + to move the highlight bar down to ???REC TIME???, then press FAR or NEAR to cycle through the choices. Stop when the desired time appears. Choose from ???1/4S???, ???1/2S???, ???1S???, or select to turn the function ???OFF???. Then press MENU to close Menu screen.

START TIME-LAPSE

RECORDING

4 Press the Recording Start/Stop button. Recording and intervals alternate automatically.

RELEASE TIME-LAPSE MODE

5 To release when the tally lamp is not blinking, set ???REC TIME??? and ???INTERVAL TIMER??? in the Menu screen to ???OFF???. To release when the tally lamp is blinking, press the Recording Start/Stop button to stop the blinking, then set ???INTERVAL TIMER??? and ???REC TIME??? in the Menu screen to ???OFF???.

+

VCR

Compartment door

Sliding latch

Compact video cassette

Reels

Recording safety hole

INSERT BATTERY

1 Slide the battery cover up to remove it, and install one ???AA(R6)??? size battery as shown in the illustration at left. Then reattach the cover.

INSERT CASSETTE IN ADAPTER

2 Slide the latch to open the adapter compartment door, then insert the cassette and close the compartment door.

PLAY BACK ON CONNECTED VCR

3 Load the cassette adapter into the VCR and play the tape back as you would any other.

REMOVE CASSETTE FROM

ADAPTER

4 Slide the latch and the compartment door opens automatically. Then insert your finger in the hole on the underside of the adapter as shown in the illustration at left, push up and remove the cassette.

NOTES:

cDuring tape loading and unloading, do not touch the reels for safety and tape protection.

cDuring special-effect playback (slow motion, still frame, etc.), the picture may vibrate or noise bars may appear on the screen.

cTo record on a VCR using a compact cassette and the adapter, cover the adapter???s recording safety hole with adhesive tape.

PLAYBACK Basic Connections

EN 29

There are three basic types of connections. When making the connections, refer also to your VCR and TV instruction manuals.

Connection To A VCR [A]

(Editing, Dubbing and Playback)

NOTE:

When connecting the cables, open the jack cover.

To AUDIO and VIDEO connectors

Audio and Video cables (optional)

Use the optional Audio and Video cables.

CONNECT CAMCORDER TO VCR

1 As shown in the illustration at left, connect the optional Audio and Video cables between the AUDIO and VIDEO connectors on the camcorder and those on the VCR.

A

To AUDIO and

VIDEO IN connectors

B

SUPPLY POWER

2 Turn on the camcorder, the VCR and the TV.

SELECT MODE

VCR

Antenna

RF unit RF-V5U (optional)

NOTES:

cIt is recommended to use the AC Power Adapter/Charger as the power supply instead of the battery pack.

cTo monitor the picture and sound from the camcorder without inserting a tape, set the camcorder???s Power switch to ???CAMERA???, then set your TV to the appropriate input mode.

cIf you have a TV or speakers that are not specially shielded, do not place the speakers adjacent to the TV as interference will occur in the camcorder playback picture.

3 Set the VCR to its AUX input mode, and set the TV to its VIDEO mode.

Connection To A TV With A/V Input Connectors [B] (Playback ONLY)

NOTE:

Use the optional Audio and Video cables.

CONNECT CAMCORDER TO TV

1 As shown in the illustration at left, connect the optional Audio and Video cables between the AUDIO and VIDEO connectors on the camcorder and those on the TV.

SELECT MODE

2 Set the TV to its VIDEO or AV mode (as specified in its instructions).

Connection To A TV With NO A/V Input Connectors (Playback ONLY)

NOTE:

Use the optional RF-V5U RF unit.

*Refer to the RF-V5U instruction manual for connection procedure.

30EN

PLAY/PAUSE

REW FF

STOP

POWER

Recording mode indicator

PLAYBACK BasicPlayback

NOTE:

Make sure you connect your camcorder as directed in ???Basic Connections??? (Z pg. 29).

LOAD A CASSETTE

1 Slide EJECT to open the cassette holder, then insert the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked.

SELECT MODE

2 Set the Power switch to ???PLAY???. The Power On indicator lights.

PLAYBACK

3 Press PLAY/PAUSE. The playback picture appears in the viewfinder and the connected TV.

STOP PLAYBACK

4 Press STOP.

Rewind or Fast-forward the tape

Press REW to rewind, or FF to fast-forward the tape during Stop mode.

NOTE:

The camcorder shuts off automatically after about 5 minutes in Stop mode or Still Playback mode. To turn on again, set the Power switch to ???POWER OFF???, then to ???PLAY???.

PLAYBACK Features

+

???

COUNTER R/M PLAY/PAUSE

STOP

REW FF

NOTES: c The counter memory functions in the FF and REW modes.

cTo disable Counter Memory Function, press COUNTER R/M so the ???M??? disappears.

When connecting the cables, open the jack cover.

Audio and Video cable (optional)

To AUDIO and

VIDEO OUT connectors

To AUDIO and

VIDEO IN connectors

Random Assemble Editing [R.A.Edit]

Create edited videos easily using your camcorder as the source player. You can select up to 8 ???cuts??? for automatic editing, in any order you like. R.A.Edit is more easily performed when the optional RM-V700U MBR (Multi-Brand Remote) is set to operate with your brand of VCR (see VCR CODE LIST), but can also be performed by operating the VCR manually.

VCR CODE LIST

EN 33

SET REMOTE/VCR CODE

SET REMOTE TO OPERATE VCR

1 Turn off the power to the VCR and point the remote toward the VCR???s infrared sensor. Then, referring to the VCR CODE LIST on the left, press and hold MBR SET, and press button (A) and then (B).

???The code is automatically set once you release the MBR SET button, and the VCR???s power comes on.

OPERATE THE VCR

2 Make sure the VCR???s power is on. Then, while holding VCR CTL, press the button on the remote for the desired function. The functions the remote can control are PLAY, STOP, PAUSE, FF, REW and VCR REC STBY (you don???t need to press VCR CTL for this one).

You???re now ready to try Random Assemble Editing.

IMPORTANT

Although the MBR is compatible with JVC VCRs and those of many other makers, it may not work with yours or may offer limited functions.

NOTES:

cIf the VCR???s power doesn???t come on in step 1, try another code from the VCR CODE LIST.

cSome brands of VCR don???t come on automatically. In this case, turn the power on manually and try step 2.

cIf the RM-V700U is not able to control the VCR, use the controls on the VCR.

cThe RM-V700U cannot be used to operate this camcorder.

MAKE CONNECTIONS

CONNECT TO . . .

1 A JVC VCR EQUIPPED WITH REMOTE

PAUSE TERMINAL

Connect the editing cable to the Remote PAUSE terminal.

B JVC VCR NOT EQUIPPED WITH REMOTE

PAUSE TERMINAL

Connect the editing cable to the R.A.EDIT connector.

C NON-JVC VCR WITH NEITHER

Connect the editing cable to the RM-V700U???s Pause-In jack.

All other connections are as shown in the illustration on page 34.

REW/FF

PREPARE CAMCORDER

Insert a recorded tape and set the Power switch to ???PLAY???.

PREPARE VCR

Turn the power on, insert a recordable tape and engage the AUX mode (refer to VCR???s instructions).

To AUDIO and VIDEO out connectors

Audio and Video cable (optional)

To AUDIO and VIDEO IN connectors

Open the cover

To J terminal (JLIP)

Editing cable (optional, 3.5?? mini-plug cable)

SELECT SCENES

ACCESS R.A. EDIT COUNTER

DISPLAY

1 Press PLAY/PAUSE, then press R.A. EDIT and the counter display appears in the viewfinder and the screen of the connected TV.

REGISTER BEGINNING OF SCENE

2 Press REW or FF to locate the beginning of a scene you want, then press IN/OUT to register that point. The data appears under IN on the display.

REGISTER END OF SCENE

3 Press REW or FF to locate the end of the scene and press IN/OUT to register it. The data appears under OUT on the display. The total time of the registered scene(s) is displayed at the bottom of the screen.

REGISTER ADDITIONAL SCENES

4 Repeat steps 2 and 3 for each additional scene (as many as 8).

MAKE CORRECTIONS

VCR (Recording deck)

5 Press CANCEL during steps 2 and 3 to erase the most recently registered point.

NOTES:

cThere must be at least one second between an in-point and its corresponding out-point.

cTo ensure correct operation, leave at least 15 seconds open between scenes.

cBlank portions of tape cannot be registered as in-points or out-points.

cIf it takes more than 5 minutes to search for an in-point, the VCR???s Record-Pause mode is cancelled and editing doesn???t take place.

cPressing R.A.EDIT clears all in- and out-points from memory.

cLeave a small margin for error around each in-point to ensure the scene is recorded in its entirety.

36EN

LENS COVER open/close switch

Set to ???POWER OFF???.

BATT. RELEASE

EJECT

PUSH

Remove

Marks

USERMAINTENANCE

After Use

1 Set the Power switch to ???POWER OFF??? to turn off the camcorder.

2 Slide EJECT to open the cassette holder, then remove the cassette.

3 Close and lock the cassette holder by pressing

PUSH.

4 Press BATT. RELEASE to remove the battery pack.

5 Slide the LENS COVER open/close switch to close the lens cover.

Cleaning The Camcorder

CLEAN EXTERIOR

1 Wipe gently with a soft cloth.

CLEAN LENS

2 Blow it with a blower brush, then wipe gently with lens cleaning paper.

CLEAN VIEWFINDER

3 1 Turn the eyepiece counterclockwise and pull it out.

2 Remove dust using a blower brush.

3 Align the marks, re-attach the eyepiece and turn it clockwise.

NOTES:

cAvoid using strong cleaning agents such as benzine or alcohol.

cCleaning should be done only after the battery pack has been removed or other power units have been disconnected.

cMold may form if the lens is left dirty.

The power suddenly goes off and doesn???t come back on by itself.

cThe battery pack has completely discharged.

cRemove the cassette and disconnect the power source, then after a few minutes, try turning the power back on. If it still doesn???t come on, consult your nearest JVC dealer.

The tape is running, but there???s no playback picture.

cThe TV has not been set to its VIDEO mode or channel.

cIf A/V connection is used, the TV???s VIDEO/TV switch has not been set to VIDEO.

cThe RF unit has not been set to the correct channel.

Noise bars appear in the playback picture.

c Manual Tracking has not been performed (Z pg. 31).

The image is out of focus.

cThe diopter needs to be adjusted (Z pg. 10).

cThe scene being shot is adversely affecting the operation of Auto Focus (Z pg. 18).

A character generator title and the date and time displays disappear from the viewfinder.

cIf you remove the power source from the camcorder while the power is on, all settings and selections are erased. Make sure to turn the camcorder???s power off before disconnecting the power source.

Even though the Lens Cover is open, the Lens Cover Warning indicator blinks.

cThe Lens Cover Warning indicator may blink when the camcorder is used in dark areas, regardless of the position of the Lens Cover.

When no cassette is inserted or when Erase Protection tab is not in the position that allows recording, the Cassette ()Warning blinks.

%Battery Pack Remaining Power Indicator Changes as follows according to the battery pack???s

remaining power level: ??????. When the power is almost gone, the indicator blinks, then the unit shuts off. Replace the battery pack with a fully charged one.

(Note: The symbol containing 3 darkened

squares ??? ??? does not necessarily mean that the battery pack is fully charged.)

) Clock Warning

Displayed for about 5 seconds if the clock (lithium) battery is not in place or is exhausted when power is turned on. Also displayed for about 5 seconds when clock battery becomes

q Condensation Warning

When this indication appears, all functions are disabled. Turn the unit off (without removing the power source) for a few hours, and when you turn it on again the indicator should disappear.

w Tape End Display ................................ Z pg. 14 Appears when the end of the tape is reached during playback, recording or fast-forward.

Connectors

wJ terminal (JLIP (Joint Level Interface Protocol) Connector.)

(Located beneath the jack cover)

???Connect the Editing Cable when performing Random Assemble Editing (Z pg. 34).

???It is used to connect the camcorder to a device such as a personal computer.

For further detail consult your nearest JVC dealer. Information (in English) is also available at our home page: http://www.jvc-victor.co.jp/

Other Parts

o Camera sensor

Be careful not to cover this area; built-in here is the sensor necessary for shooting.

A

N

B

Q

When using the AC Power Adapter/Charger in areas other than the USA

nThe provided AC Power Adapter/Charger features automatic voltage selection in the AC range from 110 V to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit???s power cord to an AC wall outlet other than American National Standard C73 series type use an AC plug adapter, called a ???Siemens Plug???, as shown.

For this AC plug adapter, consult your nearest JVC dealer.

Plug adapter

INFORMATION

This device complies with Part 15 of FCC Rules. Operation is subject to the following two condi- tions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Change or modifications not approved by the party responsible for compliance could void the user???s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

General Battery Precautions

???When the C-P6U or C-P7U (cassette adapter) are not functioning even when correctly operated, the batteries are exhausted. Replace them with fresh ones.

???Use only the following batteries:

Please make note of the following rules for battery use. When misused, batteries can leak or explode.

1.Refer to the C-P6U/C-P7U instructions when replacing the battery.

2.Do not expose batteries to excessive heat as they can leak or explode.

3.Do not dispose of batteries in a fire.

4.Remove the battery from the unit if it is to be stored for an extended period to avoid battery leakage which can cause malfunctions.

2.To prevent damage and prolong service life . . .

.... do not subject to unnecessary shock.

.... avoid repeated charging without fully discharging.

.... charge in an environment where temperatures are within the tolerances shown in the chart below. This is a chemical reaction type battery???cooler temperatures impede chemical reaction, while warmer temperatures can prevent complete charging.

.... store in a cool, dry place. Extended exposure to high temperatures will increase natural discharge and shorten service life.

.... avoid prolonged uncharged storage.

.... remove from charger or powered unit when not in use, as some machines use current even when switched off.

3. To prevent damage to the camcorder . . .

.... replace the battery pack when it begins to deliver less recording time per charge.

NOTE:

It is normal for the battery pack to be warm after charging, or after use.

Temperature Range Specifications

NOTES:

cRecharging time is based on room temperature of 20??C.

cThe lower the temperature, the longer recharging takes.

Cassettes

To properly use and store your cassettes, be sure to read the following cautions:

2.Avoid using the unit . . .

.... in places subject to excessive humidity or dust.

.... in places subject to soot or steam such as near a cooking stove.

.... in places subject to excessive shock or vibration.

.... near a television set.

.... near appliances generating strong magnetic or electric fields (speakers, broadcasting antennas, etc.).

.... in places subject to extremely high (over 40??C or 104??F) or extremely low (under 0??C or 32??F) temperatures.

3.DO NOT leave the unit . . .

.... in places of over 50??C (122??F).

.... in places where humidity is extremely low (below 35%) or extremely high (above 80%).

.... in direct sunlight.

.... in a closed car in summer.

.... near a heater.

1.During use . . .

.... make sure the cassette bears the VHS-C mark.

.... be aware that recording onto prerecorded tapes automatically erases the previously recorded video and audio signals.

.... make sure the cassette is positioned properly when inserting.

.... do not load and unload the cassette repeatedly without allowing the tape to run at all. This slackens the tape and can result in damage.

.... do not open the front tape cover. This exposes the tape to fingerprints and dust.

2.Store cassettes . . .

.... away from heaters or other heat sources.

.... out of direct sunlight.

.... where they won???t be subject to unnecessary shock or vibration.

.... where they won???t be exposed to strong magnetic fields (such as those generated by motors, transformers or magnets).

.... vertically, in their original cases.

Main Unit

1.For safety, DO NOT . . .

.... open the camcorder???s chassis.

.... disassemble or modify the unit.

.... short-circuit the terminals of the battery pack. Keep it away from metallic objects when not in use.

.... allow inflammables, water or metallic objects to enter the unit.

.... remove the battery pack or disconnect the power supply while the power is on.

.... leave the battery pack attached when the camcorder is not in use.

4.To protect the unit, DO NOT . . .

.... allow it to become wet.

.... drop the unit or strike it against hard objects.

.... subject it to shock or excessive vibration during transportation.

.... keep the lens directed at extremely bright objects for long periods.

.... direct the eyepiece of the viewfinder at the sun.

.... carry it by holding the viewfinder.

.... swing it excessively when using the shoulder strap.

5.This camcorder features a built-in head cleaner which automatically cleans the heads and head drum when a cassette is loaded or unloaded. If, however, the heads become dirty and cause blurriness or interruption in the playback picture, consult your nearest JVC dealer.

About moisture condensation . . .

???You have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass??? outer surface. This same phenomenon occurs on the head drum of a camcorder when it is moved from a cool place to a warm place, after heating a cold room, under extremely humid conditions or in a place directly subjected to the cool air from an air conditioner.

???Moisture on the head drum can cause severe damage to the video tape, and can lead to internal damage to the camcorder itself.

Serious malfunctioning

If malfunctioning occurs, stop using the unit immediately and consult your local JVC dealer.

SPECIFICATIONS

GENERAL

CAMERA

VIDEO

EN 45

AC POWER ADAPTER/BATTERY CHARGER (AA-V11U)

CASSETTE ADAPTER (C-P7U)

Provided Accessories ......................Z pg. 6

Optional Accessories

???Battery Packs BN-V12U, BN-V22U, BN-V25U

???Car Battery Charger BH-V3U

???Battery Charger BH-VC10U

???Car Battery Cord AP-V7U

???RF Unit RF-V5U

???Compact VHS-C Cassettes TC-40/30/20

???Active Carrying Bag CB-V7U

???Wireless Remote Control Unit RM-V700U

The RM-V700U cannot be used to operate this camcorder.

This comcorder can use the RM-V700U only for R.A. Edit with a non-JVC VCR.

Some acccessories are not available in some areas. Please consult your nearest JVC dealer for details on accessories and their availability.

Specifications shown are for SP mode unless otherwise indicated. E. & O. E. Design and specifications subject to change without notice.