Jasmine??? Scale JLS5

Assembly, Installation and Operating Instructions

SAVE THESE INSTRUCTIONS

NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact carrier/dealer for further instruction.

To ensure the safe installation, operation and use of the Jasmine Scale, these instructions MUST be followed:

WARNING

DO NOT use this equipment without first reading and understanding these instructions. If you are unable to understand the Warnings, Cautions, and Instructions, contact distributor before attempting to use this equipment, otherwise, injury or damage may result.

The weight capacity is limited to the lowest rated capacity of any one of the components in use (i.e., Patient Lift, Sling or Scale). The patient???s weight MUST NOT exceed the lowest rated capacity of any component.

After ANY adjustments, repair or service and before use, make sure that all attaching component parts are secure.

ACCESSORIES WARNING

Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.

Kit Description

For more information regarding Invacare products, parts, and services, please visit www.invacare.com

Removing the Swivel Bar/Cradle Attachment

NOTE: For this procedure, refer to FIGURE 1.

1. Remove the side rubber caps.

NOTE: Support the swivel bar or cradle attachment from underneath while removing the attaching hardware.

2.Remove the socket head screw, washer, bushings, top rubber cap, nylon spacers, washer and nut that attach the swivel bar or cradle attachment to the boom.

NOTE: When the attaching hardware is removed, the pin, washer and o???ring will become loose.

NOTE: Save the socket screw, small steel washer and locknut to secure the Jasmine Scale to the boom.

NOTE: Save the remaining hardware for future use of the swivel bar or cradle attachment without the scale.

O-ring

Washer

Pin

Bottom Rubber Cap

FIGURE 1 Removing the Swivel Bar/Cradle Attachment

Installing the Jasmine Scale

NOTE: For this procedure, refer to FIGURE 2.

WARNING

Patient and sling MUST be removed from the lift during ALL installation procedures.

1.Position the load cell assembly of the Jasmine Scale into the boom mounting bracket (Detail ??A?? of FIGURE 2).

2.Secure the Jasmine Scale to the boom mounting bracket with a bolt, washers, bushings, nylon washers, locknut and the top rubber cap. Securely tighten. Install the small rubber cap.

NOTE: Refer to Detail ??A?? of FIGURE 2 for washer and small rubber cap orientation.

NOTE: Ensure the shaft of the bolt passes through both sides of the boom mounting bracket.

3.Insert swivel bar pin with an o???ring and a washer through the swivel bar (Detail ??B?? of FIGURE 2).

4.Align the mounting holes in the swivel bar pin with the mounting holes in the load cell assembly (Detail ??B?? of FIGURE 2).

5.Secure swivel bar pin to the load cell assembly with a screw and locknut. Tighten securely (Detail ??B?? of FIGURE 2).

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur.

6.Weigh the patient. Refer to Operating the Scale and Weighing the Patient in the Jasmine Patient Lift Owner???s Manual, Invacare P/N 1150704.

FIGURE 2 Installing the Jasmine Scale

Operating the Scale

Keypad Functions

FIGURE 3 Operating the Scale - Keypad Functions

Weighing the Patient

WARNING

The weight capacity is limited to the lowest rated capacity of any one of the components in use (e.g. Patient Lift, Sling or Scale). The patient's weight MUST NOT exceed the lowest rated capacity of any component.

1.Attach sling straps to the swivel bar. For proper attachment instructions refer to Attaching a Sling to the Swivel Bar in the Jasmine Patient Lift Owner???s Manual, Invacare P/N 1150704.

NOTE: For improved accuracy on the patient lift, attach all sling straps to the center hooks on both sides of the swivel bar. However, patient comfort may require a different configuration of sling straps.

2.Press the ON/OFF key.

WARNING

DO NOT operate key strokes with pointed objects (e.g. pencils, pens, fingernails, etc.) Otherwise damage to the key pad will result.

NOTE: The display will indicate the last weight that was measured. The word ??LOCK?? will be seen in the display box.

NOTE: The ZERO key is pressed in order to avoid capturing the weight of the sling and the hardware. If the ZERO key is not pressed the weight of the sling and the weight of the hardware will be included in the weight displayed. NOT ZERO???ING OUT WILL GIVE A FALSE READING OF THE USER??S TRUE WEIGHT.

3.Press the ZERO key. When the ZERO key is pushed the following will happen:

A.The scale will reset to zero and the word ??ZERO?? will appear in the display.

B.The lock function will then be turned off and the word ??LOCK?? will disappear from the display.

NOTE: The scale is now active and continually updating the weight display.

4.Place the patient in the sling. For patient placement instructions refer to Operation in the Jasmine Patient Lift Owner???s Manual, Invacare P/N 1150704.

5.Activate the lift mechanism to raise the patient until they are completely supported by the lift. For patient lifting instructions, refer to Lifting the Patient in the Jasmine Patient Lift Owner???s Manual, Invacare P/N 1150704.

6.Note the weight display.

7.When the weight display becomes stable press the LOCK button to lock the weight display. This will be indicated by the word ??LOCK?? appearing in the display window.

NOTE: Should it be necessary to unlock the weight while the patient is still supported by the lift, the UNLOCK button may be pressed. The weight will unlock and the word ??LOCK?? will disappear from the display window. The weight value will then be updated. Once the weight becomes stable the weight can be locked again by pressing the LOCK button.

NOTE: Stable being defined as the weight fluctuating ?? two tenths of a pound. For example, a patient weighing one hundred lbs the scale will fluctuate between 99.8 and 100.2 until the LOCK key is pressed. Fluctuation of the weight displayed is normal as noted above. Press the LOCK button to lock the weight.

NOTE: The UNITS button can be pressed to toggle between units of pounds and kilograms. This is indicated by lb or kg appearing in the display window.

8. The lift may now be lowered and the sling removed from the patient.

NOTE: The patient??s weight will continue to be seen in the display window. The display will turn off automatically after a two minute period of non???use [no changes in weight exceeding five pounds (2 kilograms)]. You can NOT adjust the time delay for automatic shut off. After the display has turned off, the weight may be recalled by pressing the ON/OFF button. The unit can be turned off by pressing the ON/OFF button a second time.

Replacing the Battery

NOTE: For this procedure, refer to FIGURE 4.

NOTE: The scale is powered by a 9???volt alkaline battery that should provide approximately 1500 readings before needing replacement.

When battery replacement is needed, LO BAT will appear on the display. Perform the following:

1.Slide the battery door open in the direction of the arrow.

2.Remove existing battery.

3.Install the NEW battery.

4.Reinstall the battery door.

Assembled

Scale

9V Battery

Battery

Door

Arrow

FIGURE 4 Replacing the Battery

Calibrate the Jasmine Scale

NOTE: For this procedure, refer to FIGURE 5 on page 7.

NOTE: The Jasmine Scale will be pre???calibrated at the factory with the load cell. Should it be necessary to re???calibrate the scale, follow the instructions outlined below.

1.The patient and the sling MUST be removed from the scale to properly calibrate the Jasmine Scale. Refer to Operation in the Jasmine Patient Lift Owner???s Manual, Invacare P/N 1150704, for further instructions.

2.For sling detachment instructions, refer to Lifting the Patient in the Jasmine Patient Lift Owner???s Manual, Invacare P/N 1150704.

3.Turn the scale display power on by pressing the ON/OFF key.

4.Rotate the Swivel Bar until the back of the scale display is visible.

5.Insert the tip of a paper clip or similar tool into the small hole on the back of the scale display and press the CAL button.

NOTE: Once the CAL button is pressed, ???CAL1??? will be seen in the display window.

6.Press the UNITS key. The display reads CAL2.

7.Press the LOCK/UNLOCK key. The display reads UNLD.

8.Press the ZERO key. The display reads LOAD.

9.Hang 200 pounds of calibrated weight from the scale and press the ZERO key.

10.Press the ZERO key. The display reads DONE.

11. Remove the weight. Press the LOCK/UNLOCK key.

NOTE: The scale is now in test mode.

12. Press the ZERO key. The display reads 0.00 lb.

NOTE: The scale will now be in normal operation.

BACK VIEW OF SCALE DISPLAY

CAL button

FRONT VIEW OF SCALE DISPLAY

Display Window

MODEL JLS5

CAPACITY 500 lb, 227 kg

FIGURE 5 Calibrate the Jasmine Scale

Troubleshooting

Display Codes

CAL

CALIBRATION REQUIRED ??? Indicates improper stored calibration data, calibration is necessary.

OCAP

OVER CAPACITY ??? Indicates a weight exceeding the capacity has been loaded on the scale.