IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1.Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.

2.Only one person at a time should use the machine.

3.If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,

STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4.Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.

5.Keep hands away from all moving parts.

6.Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.

7.Use the machine only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.

8.Do not place any sharp object around the machine.

9.Disabled person should not use the machine without a qualified person or physician in

attendance.

10.Before using the machine to exercise, always do stretching exercises to properly warm up.

11.Never operate the machine if the machine is not functioning properly.

12.Read all warnings posted on the exercise bike.

13.Inspect the exercise bike for worn or loose component prior to use. Tighten/replace any loose or wore components prior to use.

14.Care should be taken in mounting or dismounting the exercise bike.

15.This exercise bike is for consumer and home use only.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE

OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES

NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE

SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

WARNING LABEL PLACEMENT

The Warning Labels and Caution Label shown here have been placed on the Rear Stabilizer, Main Frame.

If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the labels in location shown.

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

COMPONENTS FOR ASSEMBLY

ASSEMBLY INSTRUCTION

???Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench, provided by manufacturer.

???NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury.

STEP-1

A.) Do not tighten Bolts until instructed to do so.

B.) Attach the Front Stabilizer (#39) to the Main Frame (#35). Secure it with four M8 x 5/8??? Allen Bolts (#5)

and four ??? 5/8??? Washers (#6).

C.) Attach the Rear Stabilizer (#55) to the Main Frame. Secure it with four M8 x 5/8??? Allen Bolts (#5), and four ?? 5/8??? Washers (#6).

D.) Securely tighten all Bolts.

E.) Use the four Floor Level Adjustment Knobs (#38) to stabilize the Bike on floor.

STEP 2

A.) Connect the Upper Computer Wire (#2) from the Front Post to the Computer Wire from the

Computer (#1).

B.) Attach the Computer to the Front Post (#4). Secure it with four Computer Philips Screws (#3).

STEP 3

A.) Connect the Lower Computer Wire (#37) from Main Frame (#35) to the Upper Computer Wire (#2) from Front Post (#4).

B.) Attach the Front Post to the Main Frame. Secure it with four M8 x 5/8??? Allen Bolts (#5).

STEP 4

A.) Attach the pivot on Left Swing Handle (#30L) to the pivot on Main Frame (#35).

B.) Thread the Swing Handle Shaft (#28) though Left Swing Handle into Main Frame, and firmly secure them together.

STEP 5

A.) Attach the Swing Handle Connecting Rod (#48) to the open bracket on the bottom of the Left Swing Handle (#30L).

B.) Secure them together with one M8 x 1 ????? Allen Bolt (#49) and one M8 Aircraft Nut (#50).

STEP 6

A.) Attach the pivot on Right Swing Handle (#30R) to the pivot on Main Frame (#35).

B.) Thread the Swing Handle Shaft (#28) through Right Swing Handle into Main Frame, and firmly secure them together.

STEP-7

A.) Attach the Swing Handle Connecting Rod (#48) to the open bracket on bottom of the Right

Swing Handle (#30R).

B.) Secure them together with one M8 x 1 ????? Allen Bolt (#49) and one M8 Aircraft Nut (#50).

STEP-8

A.) Thread the Left Pedal (#41L) counter clockwise into Left Crank (#44L).

B.) Thread the Right Pedal (41R) clockwise into Right Crank (#44R).

STEP-9

A.) Remove the three ?? 5/8??? Seat Flat Washers (#32) and M8 Seat Aircraft Nut (#33) from the

Seat Pad (#31).

B.) Attach the Seat Pad to the Seat Post (#34). Secure it with the three ?? 5/8??? Seat Flat Washers (#32) and M8 Seat Aircraft Nut (#33) from the Seat Pad (#31).

STEP-10

A.) Insert the Seat Post (#34) into the opening one Main Frame (#35).

B.) Thread the Lock Knob (#63) through the hole on Seat Post to securely hold it at desired height.

EXPLODED DIAGRAM

CARE, MAINTENANCE AND STORAGE

1.Inspect and tighten all parts each time you use the machine. Replace any worn parts immediately.

2.The bike can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

3.Store the bike IN-DOOR. Excess moisture and water would cause rust on the frame.

4.The Bike shall be placed at least 24 inches away from the wall or/and any other object such as furniture to provide safe access to and passage around the machine.

5.To avoid possible injury, the help of two or more people are needed when moving the machine around.

6.Disposal Instructions ??? The equipment can be safely disassembled and disposed without unreasonable hazards. Call your local recycle agency regarding details of recycling.

7.The maximum user weight is 300 lbs.

8.Assembled Dimension: 45??? x 25??? x 47.5???

OPERATING NOTES

SEAT ADJUSTMENT

The seat height ranges from 29??? to 41???.

Loosen and pull out the Lock Knob. Slide the Seat Post to selected scale marked on the Seat

Post, then release the Lock Knob and securely fasten the Knob to lock the Seat Post.

The seat height adjustment is in approximately 1 ????? increment.

TRANSPORT

The Bike has a pair of transport Roller Wheels on Front Stabilizer. To move, carefully tilt and roll.

COMPUTER

MODE

Press ???MODE??? button, will automatically scan Time, Speed, RPM, Distance, and Calories, for every 6 seconds.

SET

1.To set up the hour, minute, year, month and date.

2.To set up the target value of Time, Distance and Calories.

RESET

1.Press the button to reset function value from previous setting.

2.Press the button and hold for 2 seconds to reset all value to zero.

When computer is in idle mode, the screen will display Calendar, Clock, and Temperature.

CALENDAR Display date, month, and year. CLOCK Display current clock time.

TEMPERATURE Displays current room temperature from 50??F to 140??F.

To set up time and date; remove batteries for few seconds, and then place batteries back.

The computer will beep and display ???8888??? and display Time/Date field.

Press ???SET??? key to enter the Time or Date field. Press ???MODE??? key to enter time/Date data.

REPLACE BATTERY:

1.Remove the battery cover on the back of the computer.

2.Replace two 1.5V (AA) batteries.

3.Make sure the batteries are installed correctly and the polarities are correct.

4.If the display is not clear or only partial segments appeared, remove the batteries and wait for 15 seconds before re-install them.

5.The battery life is approx. 3 months under normal usage.

6.When the batteries are removed, all the functional values will reset to zero.

Note:

Please note all values on this computer are approximate and they are for comparison purpose only. Do not use these values for any medical or rehabilitation purpose.