Please read the operator???s manual carefully and make sure you understand the instructions before using the machine.

English

Symbols on the machine:

WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others.

Please read the operator???s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

???Protective helmet

???Hearing protection

???Protective goggles or a visor

???Breathing mask

This product is in accordance with applicable EC directives.

WARNING! Dust forms when cutting, this can cause injuries if inhaled. Use an approved breathing mask. Avoid inhaling petrol fumes and exhaust fumes. Always provide for good ventilation.

WARNING! Sparks from the cutting blade can cause ???re in combustible materials such as: petrol (gas), wood, dry grass etc.

Noise emission to the environment according to the European Community???s Directive. The machine???s emission is speci???ed in chapter Technical data and on label.

Other symbols/decals on the machine refer to special certi???cation requirements for certain markets.

Symbols in the operator???s manual:

Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance.

Always wear protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Run position.

Stop, with the return spring to the operating position.

Stop, in the ???xed position.

Steps before using a new power cutter.

???Please read the operator???s manual carefully.

???Check the assembly and adjustment of the cutting blade. See the instructions under the heading Assembling the cutting blade.

???Start the engine and check the idling setting, see instructions under the heading Maintenance. When the carburettor is set correctly the cutting blade should be still while idling. Setting of the idle speed is described under the heading Fine adjustment of the idle speed T. Set the correct speed according to these instructions. Do not use the power cutter if the idle speed is not adjusted correctly!

???Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs.

WARNING! Under no circumstances may the

!design of the machine be modi???ed without the permission of the manufacturer. Always use genuine accessories. Non-authorized modi???cations and/or accessories can result in serious personal injury or the death of the operator or others.

WARNING! Use of products which cut, grind,

!drill, sand or shape material can generate dust and vapors which may contain harmful chemicals. Know the nature of the material being worked on and wear appropriate dust mask or respirator protection.

WARNING! A power cutter is a dangerous

!tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely important that you read and understand the contents of this Operator???s Manual.

WARNING! The ignition system of this

!machine produces an electromagnetic ???eld during operation. This ???eld may under some circumstances interfere with pacemakers.To reduce the risk of serious or fatal injury, we recommend persons with pacemakers to consult their physician and the pacemaker manufacturer before operating this machine.

Husqvarna Construction Products has a policy of continuous product development. Husqvarna reserves the right to modify the design and appearance of products without prior notice and without further obligation introduce design modi???cations.

All information and all data in the Operator???s Manual were applicable at the time the Operator???s Manual was sent to print.

Personal protective equipment

WARNING! You must use approved personal

!protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

???Protective helmet

???Hearing protection

???Protective goggles or a visor

???Breathing mask

???Heavy-duty, ???rm grip gloves.

???Tight-???tting, heavy-duty and comfortable clothing that permits full freedom of movement.

???Use leg-guards recommended for the material to be cut.

???Boots with steel toe-caps and non-slip sole

???Always have a ???rst aid kit nearby.

Machine???s safety equipment

This section describes the machine???s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ???What is what???? section to locate where this equipment is positioned on your machine.

WARNING! Never use a machine that has

!faulty safety equipment! Carry out the inspection, maintenance and service routines listed in this section.

Vibration damping system

Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier.

The machine???s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine???s handle unit.

The engine body, including the cutting equipment, is insulated from the handles by vibration damping units.

Stop switch

Use the stop switch to switch off the engine.

Muf???er

WARNING! The muf???er gets very hot in use

!and remains so for a short time afterwards. Do not touch the muf???er if it is hot!

The muf???er is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

WARNING! The exhaust fumes from the

!engine are hot and may contain sparks which can start a ???re. Never start the machine indoors or near combustible material!

6 ??? English

IMPORTANT INFORMATION

For muf???ers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and servicing the machine???s safety equipment.

WARNING! The inside of the muf???er contain

!chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muf???er.

Throttle lockout

The throttle trigger lock is designed to prevent accidental operation of the throttle. When the lock (A) is pressed in this releases the throttle (B).

A

B

The trigger lock remains pressed in as long as the throttle is pressed. When the grip on the handle is released the throttle trigger and the throttle trigger lock both return to their original positions. This is controlled by two independent return spring systems. This means that the throttle trigger is automatically locked in the idle position.

Guard for the blade

WARNING! Always check that the blade

!guard is ???tted correctly before starting the machine.

This guard is ???tted above the cutting blade and is designed to prevent parts of the blade or cutting fragments from being thrown towards the user.

Checking, maintaining and servicing the machine???s safety equipment

WARNING! All servicing and repair work on

!the machine requires special training.This is especially true of the machine???s safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent.

Vibration damping system

Regularly check the vibration damping units for cracks or deformation.

Make sure the vibration damping units are securely attached to the engine unit and handle unit.

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Muf???er

Never use a machine that has a faulty muf???er.

Regularly check that the muf???er is securely attached to the machine.

Throttle lockout

???Make sure the throttle control is locked at the idle setting when the throttle lockout is released.

???Press the throttle lockout and make sure it returns to its original position when you release it.

???Check that the throttle control and throttle lockout move freely and that the return springs work properly.

???Start the power cutter and apply full throttle. Release the throttle control and check that the cutting blade stops and remains stationary. If the cutting blade rotates when the throttle is in the idle position you should check the carburettor???s idle adjustment. See instructions under the heading Maintenance.

Checking the blade guard

Never use a defective guard or a guard that has not been ???tted correctly.

WARNING! Always check that the guard is

!correctly ???tted before starting the machine. Check that the cutting blade is ???tted correctly and does not show signs of damage. A damaged cutting blade can cause personal injury. See instructions under the heading Assembly.

Check that the guard is complete and without any cracks or deformations.

English ??? 7

General safety precautions

???A power cutter is designed to cut hard materials, such as masonry. Observe the increased risk of kickback when cutting soft materials. See instructions under the heading How to avoid kickback.

???Do not use the power cutter until you have read the entire contents of this Operator???s Manual.

All servicing, in addition to the points listed in the section ???Control, maintenance and service of the power cutter???s safety equipment???, should be carried out by trained service specialists.

???Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

???Wear personal protective equipment. See instructions under the heading Personal protective equipment.

???Never use a machine that has been modi???ed in any way from its original speci???cation.

???Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and quali???ed specialists. See instructions under the heading Maintenance.

???Never allow anyone else to use the machine without ???rst ensuring that they have understood the contents of the operator???s manual.

???Never use the machine indoors. Be aware of the dangers of inhaling the engine???s exhaust fumes.

Transport and storage

Do not store or transport the power cutter with the cutting blade ???tted.

Store the power cutter in a lockable area so that it is out of reach of children and unauthorised persons.

All blades should be removed from the cutter after use and stored carefully. Store cutting blades in dry, frost free conditions.

Special care should be taken with abrasive discs. Abrasive discs must be stored on a ???at, level surface. If blades are supplied with a backing pad then a spacer should be used to keep them ???at. If an abrasive disc is stored in humid conditions, this can cause imbalance and result in injury.

Inspect new blades for transport or storage damage.

Fuel safety

(Refuelling/Fuel mixture/Storage.)

WARNING! Take care when handling fuel.

!Bear in mind the risk of ???re, explosion and inhaling fumes.

???Never refuel the machine while the engine is running.

???Make sure there is plenty of ventilation when refuelling or mixing fuel (petrol and 2-stroke oil).

???Move the machine at least 3 m from the refuelling point before starting it.

???Never start the machine:

-If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate.

-If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

-If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

???Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked ???ames, for example, from electrical machinery, electric motors, electrical relays/switches or boilers.

???Always store fuel in an approved container designed for that purpose.

???When storing the machine for long periods the fuel tank must be emptied. Contact your local petrol station to ???nd out where to dispose of excess fuel.

???Always use a Husqvarna fuel container with an anti-spill valve.

WARNING! Bear in mind the risk of ???re,

!explosion and inhaling fumes. Stop the engine before fuelling. Do not ???ll so that the fuel runs over. Wipe up all spillage on the ground and machine. If you spill fuel on yourself or your clothes. Change your clothes. Move the machine at least 3 metres away from the refuelling area before starting.

General working instructions

WARNING! This section describes basic

!safety directions for using a power cutter. This information is never a substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice. Contact your dealer, service agent or an experienced power cutter user. Do not attempt any task that you feel unsure of!

Basic safety rules

???Look around you:

-To ensure that people, animals or other things cannot affect your control of the machine.

-To make sure that none of the above come into contact with the cutting blade.

???Do not use the machine in bad weather, such as dense fog, rain, strong wind, intense cold, etc. Working in bad weather is tiring and can lead to dangerous conditions, e.g. slippery surfaces.

???Never start to work with the power cutter before the working area is clear and you have a ???rm foothold. Look out for any obstacles with unexpected movement. Ensure when cutting that no material can become loose and fall, causing operating injury.Take great care when working on sloping ground.

???Make sure that no clothes or parts of the body come in contact with the cutting equipment when it is rotating.

???Keep at a safe distance from the cutting equipment when it is rotating.

???The guard for the cutting equipment must always be on when the machine is running.

???Ensure that the working area is suf???ciently illuminated to create a safe working environment.

???Do not move the machine when the cutting equipment is rotating.

???Always ensure you have a safe and stable working position.

???Make sure that no pipes or electrical cables are routed in the area to be cut.

Only use the machine in areas with good

!ventilation. Neglect can result in serious injury or death.

Cutting

WARNING! The safety distance for the power

!cutter is 15 metres. You are responsible to ensure that animals and onlookers are not within the working area. Do not start cutting until the working area is clear and you are standing ???rmly.

General

???Start cutting with the machine running at maximum speed.

???Always hold the machine in a ???rm grip with both hands. Hold it so that the thumbs and ???ngers grip round the handles.

WARNING! Overexposure to vibration can

!lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition.These symptoms normally appear in the ???ngers, hands or wrists. The risk increases at low temperatures.

Cutting technique

The technique described below is of a general character. Check information for each blade regarding individual cutting characteristics (for example, a diamond blades requires less feeding pressure than an abrasive discs).

???Support the work piece in such a way that it is possible to predict what will happen, and so that the cut remains open while cutting.

???Check that the blade is not in contact with anything when the machine is started

???Always cut at maximum speed.

???Start cutting smoothly, allowing the machine to work without forcing or pressing in the blade.

???Move the blade slowly forwards and backwards to achieve a small contact area between the blade and the material to be cut. This reduces the temperature of the blade and ensures effective cutting.

???Feed down the machine in line with the blade. Pressure from the side can damage the blade and is very dangerous.

???The guard for the cutting equipment should be adjusted so that the rear section is ???ush with the work piece. Spatter and sparks from the material being cut are then collected up by the guard and led away from the user.

WARNING! Under all circumstances avoid

!grinding using the side of the blade; it will almost certainly be damaged, break and can cause immense damage. Only use the cutting section.

Do not pull the power cutter to one side, this can cause the blade to jam or break resulting in injury to people.

Sharpening diamond blades

Diamond blades can become dull when the wrong feeding pressure is used or when cutting certain materials such as heavily reinforced concrete. Working with a blunt diamond blade causes overheating, which can result in the diamond segments coming loose.

Sharpen the blade by cutting in a soft material such as sandstone or brick.

Blade vibration

The blade can become out-of-round and vibrate if an excessive feed pressure is used.

A lower feed pressure can stop the vibration. Otherwise replace the blade. The blade must be of the recommended type for the material to be cut.

How to avoid kickback

WARNING! Kickback can happen very

!suddenly and violently; kicking the power cutter and cutting blade back at the user. If this happens when the cutting blade is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique.

What is kickback?

The word kickback is used to describe the sudden reaction that causes the power cutter and cutting blade to be thrown from an object when the upper quadrant of the blade, known as the kickback zone, touches an object.

General rules

???Never start to cut with the upper quadrant of the blade as shown in the ???gure, also known as the kickback zone.

???Always hold the machine in a ???rm grip with both hands. Hold it so that the thumbs and ???ngers grip round the handles.

???Keep a good balance and a ???rm foothold.

???Always cut at maximum speed.

???Stand at a comfortable distance from the work piece.

???Take care when inserting the blade in an existing cut.

???Never cut above shoulder height.

???Be alert to movement of the work piece or anything else that can occur, which could cause the cut to close and pinch the blade.

Pull in

Pull in occurs when the discs lower section suddenly stops or when the cut closes. (To avoid, see the heading ???Basic rules??? and ???Jamming/rotation???, here below.)

Pinching/rotation

If the cut is pressed together this can lead to jamming.The machine can be pulled down suddenly with a very powerful jerk.

How to avoid pinching

Support the work piece in such a way that the cut remains open during the cutting operation and when the cut is ???nished.

Cutting blades

WARNING! A cutting blade may burst and

!cause injury to the operator.

Never use a cutting blade at a lower speed rating than that of the power cutter.

Never use a cutting blade for any other materials than that it was intended for.

WARNING! Cutting plastics with a diamond

!blade or rescue blade can cause kickback when the material melts due to the heat produced when cutting and sticks to the blade.

General

Cutting blades are available in two basic designs; abrasive

Special blades

Some cutting blades are designed for stationary equipment and for use with attachments.Such cutting blades must not be used on portable power cutters.

Always contact local authorities and make sure you are following applicable directives.

Abrasive discs

The cutting material on abrasive discs consists of grit bonded using an organic binder. ???Reinforced blades??? are made up of a fabric or ???bre base that prevents total breakage at maximum working speed if the blade should be cracked or damaged.

A cutting blade???s performance is determined by the type and size of abrasive corn, and the type and hardness of the bonding agent.

Abrasive discs, types and use

Use

discs and diamond blades.

Concrete, asphalt,

Can be used to reduce dust. Run the

iron, aluminium,

disc dry for about a

cables, rubber,

using an abrasive

plastic, etc.

disc with water cooling.

Always remove the cutting blade when the machine is transported.

Make sure that the right bushing is used for the cutting blade to be ???tted on the machine. See the instructions under the heading Assembling the cutting blade.

High-quality blades are often most economical. Lower quality blades often have inferior cutting capacity and a shorter service life, which results in a higher cost in relation to the quantity of material that is cut.

Water cooling

WARNING! Water cooling, which is used

!when cutting concrete, cools the blade and increases its service life while also reducing the formation of dust. Disadvantages include dif???culties at very low temperatures, the risk of damaging ???oors and other structural elements, and the risk of slipping.

After using an abrasive disc with water cooling, run the disc dry for about half a minute. If an abrasive disc is stored in humid conditions, this can cause imbalance and result in injury.

Hand-held, high-speed machines

Our cutting blades are manufactured for high-speed, portable power cutters. If blades from other manufacturers are used, ensure that the blades conform to all regulations and demands that concern this type of power cutter.

Steel, steel alloys

Metal and other hard NOT recommended metals.

Check that the blade is approved for the same or higher speed according to the aproval plate of the engine. Never use a cutting blade with a lower speed rating than that of the power cutter.

Ensure the blade it not cracked or damaged in any other way.

Test the abrasive disc by hanging it on your ???nger and tapping it lightly with a screwdriver or the like. If the disc does not produce a resonant, ringing sound it is damaged.

Checking the drive axle and ???ange washers

Check that the threads on the drive shaft are undamaged.

Check that the contact surfaces of the cutting blade and ???anges are ???at, run correctly on the spindle and are free from foreign objects.

Do not use warped, notched, indented or dirty ???ange washers. Do not use different dimensions of ???ange washers.

Fitting the cutting blade

Husqvarna cutting blades are manufactured and approved for freehand cutting. The paper labels on each side of the blade are there to distribute the pressure from the ???ange washer and prevent the blade from slipping.

The blade is placed on the bushing between the inner ???ange washer (A) and the ???ange washer (B). The ???ange washer is turned so that it ???ts on the axle.

The shaft can be locked using a screwdriver, steel pin or the like. This is slid in as far as possible. The blade is tightened clockwise.

Tightening torque for the bolt holding the blade is: 15-25 Nm (130-215 in.lb).

Guard for the blade

The guard must always be ???tted on the machine. The guard for the cutting equipment should be adjusted so that the rear section is ???ush with the work piece. Spatter and sparks from the material being cut are then collected up by the guard and led away from the user.

WARNING! A 16 inch blade guard should

!only be used on power cutters initially equipped with a 16 inch blade guard. If a guard obtained as a spare part is ???tted on a power cutter which is equipped with a 12 or 14 inch guard, a 16 inch blade will run too fast. A cutting blade running at a too high speed can break or cause serious damage.

Fuel

CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two- stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

WARNING! Always ensure there is adequate

!ventilation when handling fuel.

Petrol

???The lowest octane recommended is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage.

Two-stroke oil

???For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines.

???Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

???Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB formulated for air-cooled, two-stroke engines.

Mixing

???Always mix the petrol and oil in a clean container intended for fuel.

???Always start by ???lling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

???Mix (shake) the fuel mixture thoroughly before ???lling the machine???s fuel tank.

???Do not mix more than one month???s supply of fuel at a time.

???If the machine is not used for some time the fuel tank should be emptied and cleaned.

Fuelling

WARNING! Taking the following precautions,

!will lessen the risk of ???re:

Do not smoke or place hot objects near fuel.

Always shut off the engine before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

???Keep the handle dry and free from oil and fuel.

???Ensure that the fuel is well mixed by shaking the container before ???lling the tank.

???Always exercise care when re???lling the fuel. Move the machine at least three metres from the fuelling area before it is started. Check that the fuel cap is tightened correctly.

???Clean around the fuel cap. Clean the fuel and oil tank regularly. The fuel ???lter should be changed at least once a year. Contamination in the tanks causes malfunction.

Starting and stopping

WARNING! Note the following before

!starting:

Do not start the power cutter without the belt guard ???tted. Otherwise the clutch could come loose and cause personal injuries.

Always move the machine away from the refuelling area before starting.

Ensure that you and the machine have a good working stance and that the cutting blade can rotate freely.

Keep people and animals well away from the working area.

Starting a cold engine

Ignition: Slide the ignition switch to the left.

Choke: Pull the choke control fully out.

Start throttle lock: Press in the throttle trigger lock, throttle control and then the start throttle lock (A). Release the throttle control and it is locked in the half throttle position. The lock releases when the throttle control is pressed in fully.

Decompression valve: Press in the valve to reduce the pressure in the cylinder, this is to assist starting the power cutter.The decompression valve should always be used when starting. The valve automatically returns to its initial position when the machine starts.

Starting a warm engine

Use the same starting procedure as for a cold engine but without setting the choke control in the choke position.

Starting

WARNING! The cutting blade rotates when

!the engine is started. Make sure it can rotate freely.

Grip the front handle with your left hand. Put your right foot on the lower section of the rear handle pressing the machine against the ground. Never twist the starter cord around your hand.

Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

When the engine starts, quickly apply full throttle to automatically disengage fast idle.

Stopping

The engine is stopped by switching the ignition off using the stop switch.

Tensioning the drive belt

???The drive belt is fully enclosed and well protected from dust and dirt.

???When tensioning the drive belt, slightly loosen the nuts (A) holding the cutting head and belt guard.

???Turn the tension screw so that the nut (B) aligns with the arrow on the guard. Shake the head to ensure the spring can tension the belt. The belt now automatically has the right tension.

???Tighten the nuts holding the cutting head.

Replacing the drive belt

???Loosen the two screws (A).

???Turn the tension screw (B) until tensioning stops.

???Remove the two screws (A).

???Remove the front belt guard (C)

???Remove the belt from the belt pulley.

???Remove the cutting head.

???Remove the screw (D). Remove the side cover.

???Replace the drive belt.

???Assemble in the reverse order as set out for dismantling.

???Check that the blade guard over the cutting blade is not cracked or damaged in any other way. Replace when damaged.

WARNING! Never use the power cutter

!without a blade guard over the cutting blade.

Belt pulley and clutch

Never start the engine when the belt pulley and clutch are removed for maintenance.

Carburettor

Your Husqvarna product has been designed and manufactured to speci???cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor.

Function

WARNING! Do not start the machine without

!the cutting arm or cutting head ???tted. Otherwise the clutch could come loose and cause personal injuries.

???The carburettor governs the engine speed via the throttle. Air and fuel are mixed in the carburettor.

Needles

The carburettor is equipped with ???xed needles to ensure the machine always receives the correct mixture of fuel and air. When the engine lacks power or accelerates poorly, do the following:

???Check the air ???lter and replace if necessary.

???When this does not help, contact an authorised service workshop.

Fine adjustment of the idle speed T

Adjust the idle speed using the T screw. When an adjustment is necessary, ???rst turn the screw clockwise until the blade starts to rotate. Now turn the screw anti-clockwise until the blade stops rotating. A correctly adjusted idle speed is set when the engine accelerates without hesitation.

Rec. idle speed: 2700 rpm

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

Fuel ???lter

???The fuel ???lter sits inside the fuel tank.

???The fuel tank must be protected from contamination when ???lling. This reduces the risk of operating disturbances caused by blockage of the fuel ???lter located inside the tank.

???The ???lter cannot be cleaned but must be replaced with a new ???lter when it is clogged. The ???lter should be changed at least once per year.

Air ???lter

Air ???lters must be regularly cleaned to remove dust and dirt in order to avoid:

???Carburettor malfunctions

???Starting problems

???Loss of engine power

???Unnecessary wear to engine parts.

???Excessive fuel consumption.

The air ???lter system consists of an oiled foam plastic ???lter (1) and a paper ???lter (2):

1The foam plastic ???lter is easily accessible under the ???lter cover A.This ???lter should be checked weekly and replaced if necessary. In order to obtain a good ???ltering effect, the ???lter must be replaced regularly or cleaned and oiled. A special HUSQVARNA oil has been produced for this purpose.

A

B

Remove the foam plastic ???lter. Wash the ???lter well in tepid soapy water. After cleaning, rinse the ???lter well in clean water. Squeeze out and allow the ???lter to dry. NOTE! High pressure compressed air can damage the foam.

Put the ???lter in a plastic bag and pour the ???lter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the ???lter inside the plastic bag and pour off the excess before ???tting the ???lter to the machine. Never use common engine oil. This would drain through the ???lter quite quickly and collect in the bottom.

2The paper ???lter is accessible under cover B. This ???lter must be replaced/cleaned when the engine's power drops. The ???lter is cleaned by shaking. Note that the ???lter must not be washed. NOTE! High pressure compressed air can damage the ???lter.

An air ???lter that has been in use for a long time cannot be cleaned completely. The ???lter must therefore be replaced with a new one at regular intervals. A damaged air ???lter must always be replaced.

IMPORTANT INFORMATION Poor maintenance of the air ???lter will cause carbon build-up on the spark plug and abnormal wear to engine parts.

Starter

WARNING! When the recoil spring is wound

!up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Always be careful when changing the recoil spring or the starter cord. Always wear protective goggles.

Changing a broken or worn starter cord

???Loosen the ???lter and cylinder cover.

???Loosen the screws that hold the starter against the crankcase and remove the starter.

???Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

???Remove any remnants of the old starter cord and check that the return spring works. Insert the new starter cord through the hole in the starter housing and in the cord pulley.

???Secure the starter cord around the cord pulley as illustrated. Tighten the fastening well and ensure that the free end is as short as possible. Secure the end of the starter cord in the starter handle.

???Guide the cord through the cut-out in the periphery of the pulley and wind the cord 3 times clockwise around the centre of the starter pulley.

???Now pull the starter handle and in doing so tension the spring. Repeat the procedure once more, but this time with four turns.

???Note that the starter handle is drawn to its correct home position after tensioning the spring.

???Check that the spring is not drawn to its end position by pulling out the starter line fully. Slow the starter pulley with your thumb and check that you can turn the pulley at least a further half turn.

Tensioning the recoil spring

???Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

CAUTION! Check that the pulley can be turned at least a further 1/2 turn when the starter cord is pulled all the way out.

Changing a broken recoil spring

???Undo the bolt in the centre of the pulley and remove the pulley.

???Bear in mind that the return spring lies tensioned in the starter housing.

???Loosen the bolts holding the spring cassette.

???Remove the recoil spring by turning the starter over and loosen the hooks, with the help of a screwdriver. The hooks hold the return spring assembly on the starter.

???Lubricate the recoil spring with light oil. Fit the pulley and tension the recoil spring.

Fitting the starter

???To ???t the starter, ???rst pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

???Fit and tighten the screws that hold the starter.

Spark plug

The spark plug condition is in???uenced by:

???Incorrect carburettor adjustment.

???Wrong fuel mixture (too much oil).

???A dirty air ???lter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting dif???culties.

???If the machine is low on power, dif???cult to start or runs poorly at idle speed: always check the spark plug ???rst before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the ???ywheel.

4Cooling ???ns on the cylinder.

5Cylinder cover

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Muf???er

The muf???er is designed to reduce the noise level and to direct the exhaust gases away from the operator.The exhaust gases are hot and can contain sparks, which may cause ???re if directed against dry and combustible material.

Never use a machine with a defective muf???er.