Please read the operator???s manual carefully and make sure you understand the instructions before using the machine.

English

Symbols

WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others.

Please read the operator???s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

???A protective helmet where there is a risk of falling objects

??? Hearing protection

??? Approved eye protection

Max. speed of output shaft, rpm

This product is in accordance with applicable CE directives.

Watch out for thrown objects and ricochets.

Machines ???tted with saw blades or grass blades can be thrown violently to the side when the blade comes into contact with a ???xed object. The blade is capable of amputating an arm or leg. Always keep people and animals at least 15 metres from the machine.

Arrows which show limits for handle positioning.

Always wear approved protective gloves.

Wear sturdy, non-slip boots.

Only use non-metallic, ???exible cutting attachments, i.e. trimmer heads with trimmer cord.

Only intended for trimmer heads.

Other symbols/decals on the machine

refer to special certi???cation requirements for certain markets.

The engine is switched off by moving the

stop switch to the stop position. CAUTION! The stop switch automatically returns to the start position. In order to prevent

unintentional starting, the spark plug cap

must be removed from the spark plug when assembling, checking and/or performing maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Approved eye protection must always be used.

Note the following before starting:

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.

Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.

WARNING! Under no circumstances may the

!design of the machine be modi???ed without the permission of the manufacturer. Always use genuine accessories. Non-authorized modi???cations and/or accessories can result in serious personal injury or the death of the operator or others.

Your warranty may not cover damage or liability caused by the use of non-authorized accessories or replacement parts.

WARNING! A clearing saw, brushcutter or

!trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator???s manual.

This engine label certi???es that the product is certi???ed in accordance with American exhaust emissions requirements EPA Ph II and CARB Tier II. The Emissions Compliance Period referred to on th emissions Compliance label indicates th number of operating hours for which the engine has been shown to meet Federal and California emisson requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.

For customer assistance call: 704-921-7000 or contact us at

our website: www.husqvarna.com

Important

IMPORTANT!

The machine is only designed for trimming grass, grass clearing and/or forestry clearing.

The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data.

Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Never use a machine that has been modi???ed in any way from its original speci???cation.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and quali???ed specialists. See instructions under the heading Maintenance.

All covers and guards must be ???tted before starting. Make sure the spark plug cap and HT lead are not damaged. Otherwise you could get an electric shock.

The machine operator must ensure that no people or animals come closer than 15 metres while working. When several operators are working in the same area the safety distance should be at least twice the tree height and no less than 15 metres.

WARNING! Never allow children to use or be

!in the vicinity of the machine. As the machine is equipped with a spring-loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Personal protective equipment

IMPORTANT!

A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator???s manual.

You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

WARNING! Listen out for warning signals or

!shouts when you are wearing hearing protection. Always remove your hearing protection as soon as the engine stops.

HEARING PROTECTION

Wear hearing protection that provides adequate noise reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective goggles must comply with standard ANSI Z87.1 in the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when ???tting cutting attachments.

BOOTS

Wear sturdy, non-slip boots.

CLOTHING

Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.

FIRST AID KIT

Always have a ???rst aid kit nearby.

Machine???s safety equipment

This section describes the machine???s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ???What is what???? section to locate where this equipment is positioned on your machine.

The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and/or repairs are not carried out professionally. If you need further information please contact your nearest servicing dealer.

IMPORTANT!

All servicing and repair work on the machine requires special training. This is especially true of the machine???s safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent.

WARNING! Never use a machine with faulty

!safety equipment. The machine???s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired.

Throttle lock

The throttle lock is designed to prevent accidental operation of the throttle control. When you press the lock (A) (i.e. when you grasp the handle) it releases the throttle control (B).

When you release the handle the throttle control and the throttle lock both move back to their original positions. This movement is controlled by two independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting.

Make sure the throttle control is locked at the idle setting when the throttle lock is released.

Press the throttle lock and make sure it returns to its original position when you release it.

Check that the throttle control and throttle lock move freely and that the return springs work properly.

See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and check that the cutting attachment stops and remains at a standstill. If the cutting attachment rotates with the throttle in the idle position then the carburettor idle setting must be checked. See instructions under the heading Maintenance.

Stop switch

Use the stop switch to switch off the engine.

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

Cutting attachment guard

This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment.

Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.

Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is ???tted this can cause serious personal injury.

Vibration damping system

Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier.

Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. See instructions under the heading Cutting equipment.

The machine???s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine???s handle unit.

Regularly check the vibration damping units for cracks or deformation.

Check that the vibration damping element is undamaged and securely attached.

WARNING! Overexposure to vibration can

!lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition.These symptoms normally appear in the ???ngers, hands or wrists. The risk increases at low temperatures.

Muf???er

The muf???er is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

A muf???er ???tted with a catalytic converter is also designed to reduce harmful exhaust gases.

In countries that have a warm and dry climate there is a signi???cant risk of ???re. We therefore ???t certain muf???ers with a spark arrestor mesh. Check whether the muf???er on your machine is ???tted with this kind of mesh.

For muf???ers it is very important that you follow the instructions on checking, maintaining and servicing your machine.

Never use a machine that has a faulty muf???er.

Regularly check that the muf???er is securely attached to the machine.

If the muf???er on your machine is ???tted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.

WARNING! Muf???ers ???tted with catalytic

!converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of ???re!

WARNING! The inside of the muf???er contain

!chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muf???er.

WARNING! Bear in mind that:

!Engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or anywhere that is poorly ventilated.

The exhaust fumes from the engine are hot and may contain sparks which can start a ???re. Never start the machine indoors or near combustible material!

Locking nut

A locking nut is used to secure some types of cutting attachment.

When ???tting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.)

When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

???Reduce the risk of blade thrust.

???Obtain maximum cutting performance.

???Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.

Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.

WARNING! Always stop the engine before

!doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

WARNING! Using an incorrect cutting

!attachment or an incorrectly sharpened blade increases the risk of kickback.

Cutting equipment

Grass blades and grass cutters are intended for cutting coarse grass.

A trimmer head is intended for trimming grass.

General rules

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended ???le gauge. An incorrectly sharpened or damaged blade increases the risk of accidents.

Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.

Fitting the J-handle

???Clip the loop handle onto the shaft. Note that the loop handle must be ???tted between the arrows on the shaft.

???Slide the spacer into the slot in the loop handle.

???Fit the nut, knob and screw. Do not overtighten.

???Attach the J-handle to the loop handle using the three screws, as shown.

???Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob.

WARNING! Only grass blades/grass cutters

!or trimmer heads/plastic blades may be used when the J-handle is ???tted. Saw blades must never be used with the J-handle.

Fitting blades and trimmer heads

When ???tting the cutting attachment it is extremely important that the raised section on the drive disc/support ???ange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is ???tted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is ???tted this can cause serious personal injury.

Fitting a trimmer guard and Superauto II 1" trimmer head

???Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the ???tting on the shaft and secure it with the bolt (L).

???Fit the drive disc (B) on the output shaft.

???Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

???Insert the locking pin (C) in the hole to lock the shaft.

???To ???t the trimmer head, ???rst separate the two halves (see diagram). Proceed as follows:

???Insert a ???nger into the centre hole of the cover (I) while grasping the cover with your other ???ngers. Using the index ???nger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half

(K). Pull apart the trimmer head, grasping the cover ???rmly.

???Place the cover (I) and the support ???ange (F) on the output shaft.

???Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

???Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

???To dismantle, follow the instructions in the reverse order.

Fitting the blade guard/combination guard, grass blade and grass cutter

???Hook the blade guard/combination guard (A) onto the ???tting on the shaft and secure with the bolt. CAUTION! Use the recommended blade guard. See the Technical data section.

Fitting other guards and cutting attachments

???Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the ???tting on the shaft and secure with the bolt (L).

G

D

F

E

C

???Fit the drive disc (B) on the output shaft.

???Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

???Insert the locking pin (C) in the hole to lock the shaft.

???Place the blade (D), support cup (E) and support ???ange

(F) on the output shaft.

???Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

???Fit the drive disc (B) on the output shaft.

???Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

???Insert the locking pin (C) in the hole to lock the shaft.

???Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

???To dismantle, follow the instructions in the reverse order.

Fuel safety

Never start the machine:

1If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

Transport and storage

???Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked ???ames, for example, from electrical machinery, electric motors, electrical relays/switches or boilers.

???When storing and transporting fuel always use approved containers intended for this purpose.

???When storing the machine for long periods the fuel tank must be emptied. Contact your local gas station to ???nd out where to dispose of excess fuel.

???Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

???The transport guard must always be ???tted to the cutting attachment when the machine is being transported or in storage.

???In order to prevent unintentional starting of the engine, the spark plug cap must always be removed during long-term storage, if the machine is not under close supervision and when performing all service measures.

WARNING! Take care when handling fuel.

!Bear in mind the risk of ???re, explosion and inhaling fumes.

Fuel

CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

WARNING! Fuel and fuel fumes are highly

!in???ammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation.

Gasoline

CAUTION! Always use high grade unleaded oil mixed gasoline (minimum 87 RON). If your machine is equipped with a catalytic converter (see chapter on Technical data) always use a good quality unleaded petrol/oil mixture. Leaded petrol will destroy the catalytic converter and it will no longer serve its purpose.

Use low-emission gasoline, also known as alkylate gasoline, if it is available.

This engine is certi???ed to operate on unleaded gasoline.

???The lowest octane recommended is 87. If you run the engine on a lower octane than 87 it can result in knocking. This gives rise to a high engine temperature, which can result in serious engine damage.

???When working at continuous high revs a higher octane rating is recommended.

Two-stroke oil

???For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%).

???Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

???Never use oil intended for four-stroke engines.

Mixing

???Always mix the gasoline and oil in a clean container intended for fuel.

???Always start by ???lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

???Mix (shake) the fuel mixture thoroughly before ???lling the machine???s fuel tank.

???Do not mix more than one month???s supply of fuel at a time.

???If the machine is not used for some time the fuel tank should be emptied and cleaned.

WARNING! The catalytic converter muf???er

!gets very hot during and after use. This also applies during idling. Be aware of the ???re hazard, especially when working near ???ammable substances and/or vapours.

Fueling

WARNING! Taking the following precautions,

!will lessen the risk of ???re:

Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling.

Always stop the engine and let it cool for a few minutes before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

???Clean the area around the fuel cap. Contamination in the tank can cause operating problems.

???Ensure that the fuel is well mixed by shaking the container before ???lling the tank.

Check before starting

For safety reasons follow these recommendations!

???Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

???Check that the support ???ange is not cracked due to fatigue or due to being tightened too much. Discard the support ???ange if it is cracked.

???Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

???Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.

???Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.

???Never use the machine without a guard nor with a defective guard.

Starting and stopping

WARNING! The complete clutch cover and

!shaft must be ???tted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Always move the machine away from the refuelling area before starting. Place the machine on a ???at surface. Ensure the cutting attachment cannot come into contact with any object.

Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Starting

Primer bulb: Press the primer bulb repeatedly until fuel begins to ???ll the bulb. The bulb need not be completely ???lled.

Choke: Set the choke control in the choke position.

WARNING! When the engine is started with

!the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.

Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand

General working instructions

IMPORTANT!

This section describes the basic safety precautions for working with clearing saws and trimmers.

If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

Avoid all usage which you consider to be beyond your capability.

You must understand the difference between forestry clearing, grass clearing and grass trimming before use.

Basic safety rules

1 Look around you:

???To ensure that people, animals or other things cannot affect your control of the machine.

???To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment.

???CAUTION! Do not use the machine unless you are able to call for help in the event of an accident.

2Do not use the machine in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc.

3Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

4Switch off the engine before moving to another area. Fit the transport guard before carrying or transporting the equipment any distance.

5Never put the machine down with the engine running unless you have it in clear sight.

The ABC of clearing

???Always use the correct equipment.

???Make sure the equipment is well adjusted.

???Follow the safety precautions.

???Organise your work carefully.

???Always use full throttle when starting to cut with the blade.

???Always use sharp blades.

???Avoid stones.

???Control the felling direction (take advantage of the wind).

WARNING! Neither the operator of the

!machine nor anyone else may attempt to remove the cut material while the engine is running or the cutting equipment is rotating, as this can result in serious injury.

Stop the engine and cutting equipment before you remove material that has wound around the blade shaft as otherwise there is a risk of injury. The bevel gear can get hot during use and may remain so for a while afterwards.You could get burnt if you touch it.

WARNING! Watch out for thrown objects.

!Always wear approved eye protection. Never lean over the cutting attachment guard. Stones, rubbish, etc. can be thrown up into the eyes causing blindness or serious injury.

Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m. Stop the machine immediately if anyone approaches. Never swing the machine around without ???rst checking behind you to make sure no-one is within the safety zone.

Working methods

WARNING! Avoid cutting with the area of the

!blade between the 12 o???clock and 3 o???clock positions. Because of the speed of rotation of the blade kickback can occur if you attempt to cut thick stems with this area of the blade.

???Before you start clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollows etc.

???Start at whichever end of the area is easiest, and clear an open space from which to work.

???Work systematically to and fro across the area, clearing a width of around 4-5 m on each pass. This exploits the full reach of the machine in both directions and gives the operator a convenient and varied working area to work in.

???Clear a strip around 75 m long. Move your fuel can as work progresses.

???On sloping ground you should work along the slope. It is much easier to work along a slope than it is to work up and down it.

???You should plan the strip so that you avoid going over ditches or other obstacles on the ground.You should also orient the strip to take advantage of wind conditions, so that cleared stems fall in the cleared area of the stand.

Grass clearing using a grass blade

???Grass blades and grass cutters must not be used on woody stems.

???A grass blade is used for all types of tall or coarse grass.

???The grass is cut down with a sideways, swinging movement, where the movement from right-to-left is the clearing stroke and the movement from left-to-right is the return stroke. Let the left-hand side of the blade (between 8 and 12 o???clock) do the cutting.

???If the blade is angled to the left when clearing grass, the grass will collect in a line, which makes it easier to collect, e.g. by raking.

???Try to work rhythmically. Stand ???rmly with your feet apart. Move forward after the return stroke and stand ???rmly again.

???Let the support cup rest lightly against the ground. It is used to protect the blade from hitting the ground.

???Reduce the risk of material wrapping around the blade by following these instructions:

1 Always work at full throttle.

2 Avoid the previously cut material during the return stroke.

???Stop the engine, unclip the harness and place the machine on the ground before you start to collect the cut material.

Grass trimming with a trimmer head

Trimming

???Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut.

???The cord can easily remove grass and weeds up against walls, fences, trees and borders, however it can also damage sensitive bark on trees and bushes, and damage fence posts.

???Reduce the risk of damaging plants by shortening the cord to 10-12 cm and reducing the engine speed.

Carburetor

Your Husqvarna product has been designed and manufactured to speci???cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor.

WARNING! The complete clutch cover and

!shaft must be ???tted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Function

???The carburetor governs the engine???s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/ fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

???The setting of the carburetor means that the engine is adapted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.

???The carburetor has three adjustment controls: L = Low speed jet

H = High speed jet

T = Idle adjustment screw

???The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti- clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

???The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic setting

???The basic carburetor settings are adjusted during testing at the factory. The basic setting is richer than the optimal setting and should be maintained for the ???rst few hours the machine is in use. The carburettor should then be ???nely adjusted. Fine adjustment should be carried out by a skilled technician.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.

Rec. idle speed 2700 rpm

Recommended max. speed: See the Technical data section.

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

Fine adjustment

???When the machine has been ???run-in??? the carburetor should be ???nely adjusted. The ???ne adjustment should be carried out by a quali???ed person. First adjust the L- jet, then the idling screw T and then the H-jet.

Conditions

???Before any adjustments are made, make sure that the air ???lter is clean and the air ???lter cover is ???tted. If you adjust the carburettor when the air ???lter is dirty it will result in a leaner mixture when the ???lter is ???nally cleaned. This can lead to serious engine damage.

???Carefully turn both jets, L and H, so that they are midway between fully screwed in and fully screwed out.

???Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

???Now start the machine according to the starting instructions and let it warm up for 10 minutes.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.

Low speed jet L

Try to ???nd the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/ 4 turn counter-clockwise.

+ 1/4

L

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine

will run smoothly in every position.The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

H

Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support ???ange and drive disc before adjusting the high speed jet H.

The high speed jet H is adjusted correctly when the machine burbles a little. If the machine races then the setting is too lean. If the engine produces a lot of smoke and burbles a lot then the setting is too rich.

CAUTION! For optimum adjustment of the carburettor, contact a quali???ed dealer/service workshop that has a revolution counter at their disposal.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. It is also important that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it may cause starting dif???culties and poor acceleration.

If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine.

If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.

Muf???er

CAUTION! Some muf???ers are ???tted with a catalytic converter. See chapter on Technical data to see whether your machine is ???tted with a catalytic converter.

The muf???er is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause ???re if directed against dry and combustible material.

Some muf???ers are equipped with a special spark arrestor mesh. If your machine has this type of muf???er, you should clean the mesh at least once a week. This is best done with a wire brush.

On muf???ers without a catalytic converter the mesh should be cleaned weekly, or replaced if necessary. On muf???ers ???tted with a catalytic converter the mesh should be checked, and if necessary cleaned, monthly. If the mesh is damaged it should be replaced.

If the mesh is frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your dealer to inspect the muf???er. A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston. See also instructions under the heading Maintenance.

CAUTION! Never use a machine with a defective muf???er.

WARNING! Muf???ers ???tted with catalytic

!converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of ???re!

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Fins on the ???ywheel.

3Cooling ???ns on the cylinder.

4Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Spark plug

The spark plug condition is in???uenced by:

???Incorrect carburetor adjustment.

???An incorrect fuel mixture (too much or incorrect type of oil).

???A dirty air ???lter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting dif???culties.

If the machine is low on power, dif???cult to start or runs poorly at idle speed: always check the spark plug ???rst before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder.

Air ???lter

The air ???lter must be regularly cleaned to remove dust and dirt in order to avoid:

???Carburettor malfunctions

???Starting problems

???Loss of engine power

???Unnecessary wear to engine parts

???Excessive fuel consumption.

Clean the ???lter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air ???lter

Remove the air ???lter cover and take out the ???lter. Wash it clean in warm, soapy water. Ensure that the ???lter is dry before re???tting it.

An air ???lter that has been in use for a long time cannot be cleaned completely.The ???lter must therefore be replaced with a new one at regular intervals. A damaged air ???lter must always be replaced.

If the machine is used in dusty conditions the air ???lter should be soaked in oil. See instructions under the heading Oiling the air ???lter.

Oiling the air ???lter

Always use HUSQVARNA ???lter oil, art. no. 531 00 92-48. The ???lter oil contains a solvent to make it spread evenly through the ???lter. You should therefore avoid skin contact.

Put the ???lter in a plastic bag and pour the ???lter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the ???lter inside the plastic bag and pour off the excess before ???tting the ???lter to the machine. Never use common engine oil. This would drain through the ???lter quite quickly and collect in the bottom.

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (The US Environmental Protection Agency), CARB (California Air Resources Board) and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards. Husqvarna Forest & Garden must warrant the emission control system on your small nonroad engine for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. Your emission control system includes Parts such as the carburetor and the ignition system. Where a warrantable condition exists, Husqvarna Forest & Garden will repair your small nonroad engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.

MANUFACTURER???S WARRANTY

COVERAGE

The 2001 and later small nonroad engines are warranted for two years. If any emission related part on you engine (as listed above) is defective, the part will be repaired or replaced by Husqvarna Forest & Garden.

OWNER???S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator???s Manual. Husqvarna Forest & Garden recommends that you retain all receipts covering maintenance on your small nonroad engine, but Husqvarna Forest & Garden cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small nonroad engine owner, you should, however, be aware that Husqvarna Forest & Garden may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modi???cations or the use of parts not made or approved by the original equipment manufacturer. You are responsible for presenting your small nonroad engine to a Husqvarna Forest & Garden authorized servicing dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487-5963.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine is delivered.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding

your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487-5963.

WARRANTY PERIOD Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of ???repair or replace as necessary??? shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the ???rst scheduled replacement point for that part.

DIAGNOSIS The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Husqvarna Forest & Garden servicing dealer.

CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modi???ed parts can be grounds for disallowing a warranty claim. Husqvarna Forest & Garden is not liable to cover failures of warranted parts caused by the use of add-on or modi???ed parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800- 487-5963.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND

REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS

LIST

1Carburetor and internal parts

2Intake pipe, air???lter holder and carburetor bolts.

3Air???lter and fuel???lter covered up to maintenance schedule.

4Ignition System

1 Spark Plug, covered up to maintenance schedule

2 Ignition Module

5Muf???er with catalytic converter

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as de???ned in the operator???s manual.

S35

2,4-2,7 mm .095-.106"