IMPORTANT SAFETY INFORMATION

1. Although the HUSKY 2.25 candle power spotlight can be recharged using

either AC or DC power sources, it is not designed to operate directly from the supplied AC Recharge Adapter. Doing so may result in damage to the unit, and will void the warranty.

2.You CAN CHARGE and OPERATE the HUSKY spotlight directly from the supplied DC adapter. (Recharge/power adapter)

3.Do not use charging systems other than those supplied by the manufacturer.

4.Do not leave the SPOTLIGHT charging for more than 24 hours (AC method) or 6 hours (DC Method).

5.Do not completely discharge the battery before recharging. Deep discharge will decrease battery life.

6.Recharge the battery in a well ventilated area.

7.Never look directly into the light.

8.Use caution when handling the light as the lens becomes hot during use.

9.Store with Spotlight turned OFF and Trigger Lock ON.

10.Store with Area light in handle turned OFF.

11.Do not operate spotlight with lens against flammable materials.

12.Keep light away from children, it is not a toy.

INTRODUCTION

Congratulations on purchasing the HUSKY 2.25 million candle power spotlight, an advanced design combination spotlight and area light. It instantly converts use from a powerful spotlight to a soft, long-lasting area light. It uses a powerful proven-technology rechargeable, non- spillable sealed lead acid battery that allows for years of dependable use, recharge after recharge. It was designed from the ground up to be the most versatile and practical light for travel, camping, picnicking, tailgate parties and boating. The spotlight gives you the kind of light you need, when and where you need it.

1. FEATURES:

???Cordless/Corded, powerful Quartz Halogen Spotlight for use whenever and wherever you need light

???Longer run-time battery - minimum of 20 minutes continuous use for Spotlight on single charge

???The tough, weather-resistant HUSKY 2.25 candle power spotlight is built for rugged, outdoor use

???Intense 2.25 Candle Power Beam carries up to one mile and easily penetrates rain, fog or smoke

???Powerful, brighter Quartz Halogen Bulb delivers a bright, tight beam up to 10 times the distance of a standard automobile headlight

???Computer designed parabolic reflector

???Area utility light built into handle provides long-term lighting for repair work,

or as a flashlight operates 14 hours on full charge

???Battery Status Panel shows battery charge; It remains lit while recharging.

???E-Z-Store, built-in stand provides hands-free use of the spotlight, or the utility light (excellent for roadside repairs, power outages, etc.)

2

???Built-in hanging lanyard for hands-free convenience

???Cordless operation allows complete freedom of movement, corded for longer run time

???Pistol-grip handle fits comfortably in your hand

???Locking Trigger ON/OFF Switch delivers an instant beam, locks for continuous beam

???Unique switch-locking mechanism prevents accidental battery rundown

???May be charged from either AC or DC Power Sources (both charging adapters included)

BUILD-IN

WORKSTAND

FIGURE 1

BATTERY STATUS

PANEL

SLIDING TRIGGER

LOCK

2. CHARGING:

FIGURE 2

CHARGING PORT

NOTE: During charging, use the handy, built-in stand (See Figure 3) to provide a steady base for the spotlight on floor, shelf, workbench, or vehicle floor.

Charging with AC 110/120 Volt AC charger - Plug the AC charger (included) into the charging port on the back of the HUSKY spotlight 2.25 body, and then plug into a standard AC wall outlet. Make sure the electric rating of your AC Power Supply matches the requirements listed on top of the AC CHARGER (110V AC). Make sure the Trigger Switch is in the OFF position. For initial charge, allow 20 hours for completion of a full charging cycle. For subse- quent charges, allow approximately 8-10 hours. Charge until the green Battery Status Panel LED is lit.

NOTE: Charging from a 110/120 Volt AC power source is the most efficient method and is especially recommended for first-time charging.

Charging/Powering with 12 VOLT DC Charger - Plug the DC fused Recharge/Power Adapter (included) into the barrel receptacle on the back of the spotlight body, and then insert the cigarette lighter plug into the cigarette lighter socket of your vehicle or other 12 VDC power source. Make sure the Locking Trigger Switch is in the OFF position. Allow approximately 3???5 hours charging time if the engine is running. You may use the spotlight while its internal battery is recharging. When the spotlight is OFF charge until the green battery status panel LED is lit. NOTE: Be sure to use only the adapter cords supplied by the manufacturer for recharging - The use of unauthorized adapter cords may damage the unit and will void the warranty.

3

3. OPERATION:

The Spotlight can be operated with or without the battery installed. Operation from external 12 volt DC source with at least 10 amps capacity will allow lamp operation and internal battery charge.

SPOTLIGHT ??? Using the locking trigger switch:

???The trigger switch is located on the front of the pistol-grip handle of the spotlight (See Figure 1)

???To turn the Spotlight 2.25 ON, squeeze the trigger switch

???To turn the Spotlight 2.25 OFF, release the trigger switch

???To lock the trigger switch into the ON position for continuous operation, squeeze the trigger switch and firmly slide the trigger locking button (see Figure 1); the spotlight will stay on until the lock is released

AREA UTILITY LIGHT

???Will provide 14 hours of continuous utility lighting - THE AREA UTILITY LIGHT is ideal for roadside repairs, as a flashlight, for work areas, for use as a campsite area light, for power outages, etc

???The ON/OFF button for the area light is located near the bottom of the handle, on the left side (see Figure 1 & 3)

???To turn the area light ON, press the button

???To turn the area light OFF, press the button

NOTE The area light switch also turns on the Battery Status Panel LEDs. Recharge when just the red LED is lit.

4. HANDS-FREE OPERATION:

USING THE BUILT-IN HANGING LANYARD:

The lanyard may be used to hang the spotlight from a branch, hook or other convenient object. Adjust the slide on the cords to keep the lanyard secure around the supporting object.

USING THE BUILT-IN STAND:

???Lift and rotate the stand to desired angle

???Turn the spotlight upside-down, and rest it on the stand (see Figure 3)

???The spotlight and/or area utility light may now be used hands-free

???For hand-held operation, simply fold the stand into the storage postion

FIGURE 3

AREA UTILITY

LIGHT SWITCH

UTILITY WORK

STAND

4

5. BULB REPLACEMENT:

For bulb replacement you will need a small Phillips screwdriver. To replace the H3 12 Volt 100 watt Halogen Spotlight Bulb (See Figure 4A and Figure 4B):

1.Disconnect the Spotlight 2.25 from any charging/power source and lock the spotlight trigger switch OFF

2.Remove the rubber bezel by pulling it away from the spotlight lens.

3.Remove the two Phillips-head screws that hold the retaining ring to the spotlight body.

4.Pull off the retaining ring and set it aside.

5.Carefully remove the glass lens, rubber ???O??? ring and reflector assembly.

6.Loosen (no need to fully remove) the phillips-head screw in the neck of the reflector assembly - this will release the bulb unit.

7.Disconnect the bulb???s center conductor wire from it???s connecting wire (See figure 4B for bulb removal details).

8.Unsnap the hairpin retaining wires from the reflector???s flange.

9.Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely remove this screw).

10.Gently pull out the bulb unit and replace with a new H3 12V 100 watt Halogen Bulb from HUSKY (or minimum H3 12V 55W), available from an electrical supply house or from HUSKY???s Technical Support Department, call (800) 916-7004.

11.Insert the replacement bulb into the reflector???s flange.

12.Put back and secure the hairpin retaining wires.

13.Connect the bulb power wire to the red power wire.

14.Reverse the above procedure to re-assemble the spotlight.

NOTE: It is recommended that the unit be returned to Vector for replacement of the spotlight bulb. Contact HUSKY???s Technical Support Department at (800) 916-7004.

NOTE: When handling a new halogen bulb, do not touch the glass portion of the bulb. Natural oils from your hands can cause the bulb to fail. If necessary, clean the bulb with alcohol or a liquid window cleaner.

5

REPLACING THE AREA LIGHT BULB:

1.This 12V bulb is designed to last for the lifetime of the product.

2.In the event of failure, you may return the spotlight to HUSKY for bulb replacement. Contact HUSKY???s Technical Support Department at (800) 916-7004.

6. BATTERY:

???The life expectancy of the 12 Volt 3.0 Amp-hour, sealed lead-acid battery is approximately 500 charging cycles. A replacement battery may be purchased through the HUSKY

Technical Support Department by calling (800) 916-7004

???A fully-charged battery will provide approximately 20 minutes of continuous light from the spotlight, or up to14 hours of continuous light from the area utility light

???Do not allow battery to completely discharge, a dim light indicates that the battery charge is low, and should be recharged. Charge battery as soon as possible after each use; monitor

charge status by color

REPLACING THE BATTERY PACK:

All lead acid batteries fail over time and with extreme temperature changes. Keeping the battery charged periodically will extend battery life to the maximum. Recharge after each use as soon as possible using AC/DC recharge adapter as DC recharge methods may not fully recharge the battery to its full capacity. If the battery does not operate the spotlight for more than 10 minutes and recharge is sufficient to fully charge the battery, then it is time to replace the battery.

1.Disconnect the SPOTLIGHT 2.25 from the Charging/Powering Source.

2.Make sure the Trigger Switch is turned OFF and locked.

3.Follow the lamp replacement procedures to step 10.

4.Carefully disconnect the positive and negative wires from the battery terminals, noting the position of the wires.

5.Using a small Phillips head srewdriver remove 4 battery hold down strap screws.

6.Set the battery aside and insert the new battery taking care to MATCH UP THE PROPER POLARITY - POSITIVE (red) to positive; negative (Black) to negative.

7.Attach wires to terminals.

8.Replace the battery hold down straps and screws (Do not over-tighten - clockwise)

9.Reassemble spotlight reflector by reversing the bulb replacement procedure.

10.Test the spotlight by operating the trigger switch. Charge the new battery for 20 hours using the AC/DC Recharge Adapter.

6

BATTERY DISPOSAL:

1.Non-spillable sealed lead-acid Battery - This battery is fully recyclable and should be accepted at any location that accepts common automotive starter batteries. Examples of places that accept these batteries are: County or municipal recycling drop-off centers, scrap metal dealers, and retailers who sell automotive replacement lead acid starter batteries. For more information on recycling this battery, call toll-free (877) 288-7722.

2.Before disposing of the battery, protect exposed terminals with heavy-duty tape to prevent shorting (Shorting can result in injury or fire).

3.Do not expose battery to fire or intense heat as it may explode.

The plug of the DC Power/Charging adapter is equipped with a 10 amp cartridge fuse. If this fuse blows, there may be a short circuit in the power cord or lamp assembly. The fuse will blow if the battery is connected with reverse polarity. The fuse is accessed by unscrew- ing (counter-clockwise) the tip of the large DC plug. Check the fuse with an ohmmeter or other continuity checker. If the fuse is open, investigate why it blew and correct the problem before replacing the fuse. Reassemble the DC plug and power the lamp from a 8 Amp or greater 12 volt power supply.

SPECIFICATIONS

7