Backboard and Rim
Owners Manual
Customer Service Center
??? N53 W24700 South Corporate Circle ??? Sussex, WI 53089 ??? U.S.A.
Read and understand operator's manual before using this unit.
Failure to follow operating instructions could result in injury or damage to property.
REQUIRED TOOLS AND
MATERIALS:
???Step Ladder 8 ft. (2.4 m)
???Adjustable Wrench
???Wrenches: 7/16???, 1/2???, 9/16???, 3/4???
For Canada:
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia:
Internet Address: http://www.huffysports.com
?? COPYRIGHT 2000 by HUFFY SPORTS
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly. Check entire box and inside all packing material for parts and/or additional instructional material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document.
???If using a ladder during assembly, use extreme caution.
???Two (2) people are recommended for this operation.
???Check base regularly for leakage. Slow leaks could cause system to tip over unexpectedly.
???Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play and/or transport of the system.
???Climate, corrosion or misuse could result in system failure.
???Minimum operational height is 6' 6" (1.98 m) to the bottom of backboard.
???This equipment is intended for home recreational use only and NOT excessive competitive play.
???Read and understand the warning label affixed to pole. Label is shown on page 1.
???The life of your basketball pole depends on many conditions. The climate, placement of the pole, the location of the pole, exposure to corrosives such as pesticides, herbicides or salts are all important.
???If technical assistance is required, contact Huffy Sports.
???Adult supervision is recommended when adjusting height.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT
IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow these rules for safe operation of the unit.
??See instruction manual for proper installation and maintenance.
??Use caution when performing dunk type activities on this unit.
??Do not hang from any part of unit, including backboard, support braces, rim or net.
??Check unit before each use for loose hardware, excessive wear and signs of corrosion and repair before using.
??During play, use extreme caution to keep player's face away from the backboard, rim or net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
??During play, do not wear jewelry (rings, watches, necklaces, etc.) Objects may entangle in net.
In the U.S.:
206118 5/97
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
WARRANTY CARD:
Please remember to complete your product registration form either
For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at http://www.smarthoops.com.
Get to know the basic parts of your basketball system.....
FRONT
BACKBOARD
RIM
NET
SECTION A: ASSEMBLE THE BACKBOARD AND RIM
This is what your system will look like when you???ve finished this section:
HARDWARE USED IN THIS SECTION
TOOLS REQUIRED FOR THIS SECTION
3/4", 9/16??? and 1/2???
(not actual size)
Item #18 (2)
Item #3 (6)
AND/OR
Item #16 (8)
3/4", 9/16??? and 1/2???
Item #19 (2)
IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL
IMPORTANT!
For spring loaded rim assembly, refer to instructions included with rim hardware.
NOTE:
We recommend mounting backboard to a solid material (steel) behind rim area.
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED
IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL
NUMBER FOR FREE REPLACEMENT:
U.S.
POLE, ROOF, OR WALL MOUNT
Model 8406 Universal Mounting Bracket is available for purchase by calling this number:
15
IMPORTANT!
For spring loaded rim assembly, refer to instructions included with rim hardware.
6
6
5
4
3
4 3
15
5
ELEVATOR MOUNTS
Specific Elevator Mount Components Are Not Included
IMPORTANT!
All Elevator mounts will require this initial step of attaching brackets (8) to the backboard.
A
SPRING STYLE ELEVATOR MOUNT
6 6
8
IMPORTANT!
For spring loaded rim assembly, refer to instructions included with rim hardware.
15
SPRING STYLE ELEVATOR MOUNT (continued)
NOTE:
Use existing elevator components.
8
BBRONZE RATCHET ELEVATOR MOUNT
NOTE:
Use existing elevator components.
CSTAMPED RATCHET ELEVATOR MOUNT
NOTE:
Use existing elevator components.
8
NOTE:
Use existing elevator components.
2.Install clips.
WARNING!
USE OF THIS PRODUCT
WITHOUT PROPER
INSTALLATION OF
SMART CLIPS, OR WHEN
ALL SMART CLIPS ARE
NOT PRESENT COULD
RESULT IN BODILY
HARM. BE SURE TO
FOLLOW DIRECTIONS
CAREFULLY.
CLIP ???ARM???
CLIP ???BODY???
12
Insert one ???arm??? of clip into ram as shown. Twist ???body??? of clip slightly so that second ???arm??? slides over the top of the first ???arm???
as shown.
Push in direction indicated by arrows.
13
A
Push second ???arm??? back and into ram as shown.
B
Twist ???body??? of clip slightly again to spread ???arms??? of clip. Clip ???arms??? must be flat and touching edge to edge as shown, not overlapping.
C
NET INSTALLATION
Insert net into bottom of clip as shown.
SIDE VIEW
NETCLIP
NET
Twist net until it snaps into position. Net must be centered through clip.
SIDE VIEW
NETCLIP
NET