Installation Instructions

GENERAL INFORMATION

The 5800MICRA wireless recessed transmitter is a reed switch magnetic contact transmitter that allows the transmitter to be concealed from view when installed in a window. It is intended for use only with alarm systems that support 5800 series devices. The transmitter is powered by a long-life lithium battery that is easily replaceable when a low battery is indicated by the control panel.

Programming the ID Number

Each 5800MICRA has its own unique identification code (serial number) permanently assigned during manufacturing.

The control panel is required to "enroll" the transmitter's ID during installation of the alarm system. The zones input type should be enrolled as "RF" (i.e. Supervised RF) Type (mandatory for all UL installations).

Refer to the control panel's installation instructions for further details.

PRELIMINARY CONSlDERATlONS

Under no circumstances should the outer wall of the window frame be penetrated by the Forstner bit.

Figure 1

1 Measure & Drill

Measure 3" down from the inside top corner of the mainframe and mark the center point for the hole the 5800MICRA transmitter will be inserted into.

Place a corresponding mark also on the sash insert that will be used in this position.

5800MICRA

Wireless Recessed

Transmitter

Using a 3/4" Forstner Drill Bit with a stop collar, drill into the vinyl window mainframe.

Side mount transmitter on Vinyl Sliders

Vertical Sliding

Sash

WARNING: under no circumstances should the outer wall of the window frame be penetrated by the Forstner bit.

Sill mount transmitter on Hung Windows

Read all of this and the next section before installing the unit.

body into the cored opening. Insure that the antenna moves freely in the window channel during installation.

NOTE: It is essential to the systems operation that the positioning of the iON icon on the transmitter point in the same direction as its corresponding sash magnet.

3 Sash Magnet

Placement

Using a 3/4" Forstner Drill Bit, drill into the window sash to a depth of 11/32" only.

Sash Magnet

Press the 5800MICRA transmitter's corresponding magnet into the cavity now drilled into the sash, making sure to position the iON icons to point in the same direction. NOTE: This point is essential to the systems proper operation.

Page 1

5800MICRA

Wireless Recessed

Transmitter

Page 2

Reed Switch on

top side of PC board

MOUNTING (See Figure 1)

1.Mark the selected location for the transmitter on the frame of the window.

2.Mark the location for the magnet on the window sash, directly opposite the transmitter location. Before drilling any holes, make sure that the successful Go/No Go reception tests have been conducted as called for in the 5800 MICRA transmitter section. (see Page 1)

3.Drill holes at the locations marked, for the transmitter (3/4" diameter, no more than 11/32" deep) and magnet (3/4" diameter, no more than 11/32" deep using a 3/4 Forstner bit).

(inside cap)

Reed Switch Positioning - insure that logos on switch and magnet are aligned identically.

Figure 3

4.lnsert the transmitter and magnet cases into their respective holes so that their caps are flush with the surface. Make sure the antenna goes into the cavity as straight as possible.

DO NOT hammer the transmitter or the magnet in place with hard blows. Press them into their respective holes by hand.

The 5800MICRA uses a santaprene case that, once placed, is designed to self- seal in the mounting hole. However, if desired, a thin bead of silicon may be applied for additional moisture protection.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibility of developing and offering a regular maintenance program to the user, as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to insure the system's operation at all times.

REFER TO THE lNSTALLATlON lNSTRUCTlONS FOR THE RECEIVER / CONTROL WlTH WHlCH THlS DEVlCE lS USED, FOR WARRANTY lNFORMATlON AND FOR DETAlLS REGARDlNG LlMlTATlONS OF THE ENTlRE

ALARM SYSTEM.

BATTERY INSTALLATION & REPLACEMENT

1.Remove the transmitter from the window by inserting the flat blade of a small screwdriver into the pry-slot on the cap end and twisting slightly counter-clockwise. The transmitter must be removed from the window completely in order to refit the transmitter properly back into the hole once the internal battery has been replaced.

2.Using the flat blade of a small screwdriver in the pry-slot again, separate the white cap from the orange base with a slight counter-clockwise twist. Once open, slide the cap with the transmitter PC board assembly apart from the orange base. Pull the antenna through the hole in the orange base just enough to allow the battery to be replaced. Do not pull the antenna completely out of the orange base.

3.Remove the old battery from it's battery holder on the bottom of the PC board.

US Patent No. 6,737,969 Copyright ?? 2004 Honeywell Corporation

4.Observe correct polarity (see Figure 3 Step 3 & 4) and insert the fresh battery into the battery holder (positive polarity indicator is shown on the battery holder).

5.Slide the cap with the PC board assembly back into its orange base by gently pulling on the antenna, easing the transmitter cap into place.

6.Snap the transmitter cap back onto the orange base, locking it into place.

7.Placing the antenna into the cavity first, reinsert the transmitter into its original mounting hole in the window. Be sure to point the 'iON' graphic on the cap in the same direction as the 'iON' graphic on the accompanying sash-mounted magnet.

165 Eileen Way

Syosset, NY, 11791

Printed in Canada