Honeywell_Clock

SIDE VIEW

OPERATION

Once the unit is powered, it will show all available LCD display segments. The Weather Radio display line will remain blank for 2 seconds. Then, SIGNAL LOSS statement with RF reception icon will appear and radio

will start scanning through all 7 NOAA channels. If the reception is successful, it will detect and lock on the available channel.

WEATHER RADIO

ABOUT THE NATIONAL WEATHER RADIO SYSTEM

The National Weather Service (NWS) is a government agency within the National Oceanic and Atmospheric Administration (NOAA) that operates the nationwide radio network known as NOAA Weather Radio (NWR).

NWR is a nationwide radio stations network continuously broadcasting information about all types of hazardous events both environmental and technological. Broadcasts consist of local, regional and marine weather conditions & forecasts that are repeated every few minutes. During emergencies, routine broadcasts are interrupted to report specific warnings.

NWR works with the Federal Communications Commission???s (FCC) Emergency Alert System (EAS), to provide the most complete, single source of nationwide weather and emergency information.

As a nationwide network, the NWR consists of over 940 transmitters in all 50 US states, adjacent coastal waters, Puerto Rico, the US Virgin Islands and US Pacific Territories. This network also includes Weather Radio Canada which is a part of Meteorological Service of Canada (MSC). When the NWR broadcasts specific warning, a digital code of Specific Area Message Encoding (SAME) is included as part of the message. The SAME code consists of specific information containing the geographical area affected, the expiration time of the message and the message itself. Your Weather Radio has been designed to receive and decode warning, watch or non-emergency messages that are broadcast in digital SAME code by the National Weather service. Once received, the message will be presented visually and by voice announcement. The SAME code contains the type of message, country(s) affected, and message expiration time. Your radio should provide reception for up to 40 miles distant from the NWR transmitter depending on terrain and man made structures, either of which can reduce that distance.

You can customize the radio to only receive event messages occurring in your specific location. You can program up to nine (9) specific county locations based on system FIPS (Federal Information Processing Standard) codes you have entered into the radio memory.

NOTE: For customizing your Weather Radio use the Weather Radio Control Panel buttons located on the front of the main unit.

CUSTOMIZING YOUR WEATHER RADIO

Weather Radio allows selecting and programming of several different features, including the weather radio channel, country, language of the events (alerts), alerts, location, signal reminder, alert reminder and alert mode.

CHANNEL SEARCH

There are two options available for searching of NWR channels ??? an auto and manual.

The default channel search mode is auto.

If an auto search is selected, leave the Weather Radio in the default mode after the main unit has been powered. Then the Weather Radio will scan automatically through all 7 NOAA frequencies (channels) and lock on the strongest available channel.

When an auto search is selected and reception is successful, the Weather Radio will display the number of the received channel (for example: CHANNEL 7).

If no channel is detected at this time, the message NO CHANNEL AVAILABLE BACK TO CHANNEL X will be displayed.

If a manual search is selected, follow this programming procedure:

???Press MENU/SELECT button until message MANUAL is displayed

???Press MENU/SELECT once entering into the channel search programming mode ??? a channel number will be displayed

???Press ??? or ??? adjusting the desired channel number - 1 through 7

???Press WEATHER/SNOOZE button on the main unit to listen a NWR broadcast ??? the icon NOAA will be displayed next to the reception status icon []

???Press ??? to exit

NOTE: If your Weather Radio is receiving a NWR broadcast on more than one channel, the one with the best reception may not be the best option for your location. Contact NWS for information regarding broadcasting stations locations.

To contact the NWS by telephone, dial 1-888-NWR-SAME (1-888-697-7263)

To obtain NWS radio channels and SAME codes on Internet: www.nws.noaa.gov/nwr/indexnw.htm

COUNTRY SELECTION (US or Canada)

???Press MENU/SELECT button entering into the programming mode. Continue button presses until SELECT CH is displayed

???Press ???button until the SET COUNTRY message is displayed

???Press MENU/SELECT button to enter country programming mode

???Press ??? or ??? to select either the US or Canada

???Press MENU/SELECT button to confirm ??? the unit will beep once confirming the country selection

???Press ??? to exit

LANGUAGE SELECTION

???Press MENU/SELECT button entering into the programming mode until SELECT CH message is displayed

???Press ???or ???buttons until the SET LANGUAGE message is displayed

???Press MENU/SELECT button to enter language programming mode

???Press ??? or ??? selecting English, Spanish or French

???Press MENU/SELECT button to confirm ??? the unit will beep once confirming the language selection

???Press ??? to exit

ALERTS SELECTION

Your Weather Radio contains all NWR events (alerts) pre-programmed; many of them are set to ON by default.

There are three events (alerts) categories may be displayed ??? Advisory,

Watch or Warning

Advisory- an advisory is issued when a hazardous weather or hydrologic event is occurring, imminent or likely. Advisories are for less serious conditions than warnings, which cause significant inconvenience and if caution is not exercised, could lead to situations that may threaten life or property.

Watch ???potential severe weather approaching your area. It does not mean severe weather occur, but that the right conditions exist which could lead to severe storms. You should be prepared for the weather to deteriorate rapidly.

Warning ???severe weather is imminent or present in your vicinity. You should immediately take precautions to protect yourself and your family.

1112

Refer to Appendix 2 for a list of NWS events (alerts) to determine the events you would like to receive and those to disable.

Use this procedure for programming Weather Radio alerts:

???Press MENU/SELECT button entering into the programming mode until SELECT CH message is displayed

???Press ???or ???button until the SET ALERTS? message will be displayed

???Press MENU/SELECT button entering into the alerts programming mode

???Press ??? or ??? selecting ADVISORY, WATCH or WARNING

???Press MENU/SELECT button to select the event type ??? the first specific event will be scrolling on the display

???Press ???or ???button selecting ALERT ON or ALERT OFF

???Press MENU/SELECT button to select and confirm the setting

???Press ??? to exit

PROGRAMMING YOUR LOCATION

Your Weather Radio is pre-programmed to receive seven NOAA broadcast frequencies (channel1-7):

NOAA Radio Channels

After the strongest available channel has been detected by your Weather Radio, all FIPS codes specific for your location (state and county) are automatically pre-set.

You can customize your radio and program it with FIPS codes to listen for only those events that you are interested in. You can enable advisories, watch and warnings, to report only on events that are happening in your surrounding location for example.

Programming Locations

???Press MENU/SELECT button mode until SELECT CH message is displayed

???Press ???or ???button until LOCATION message is displayed

???Press MENU/SELECT button to enter location programming mode

???Press ??? or ??? to select from the following three options: ALL, to receive messages from all counties within a 40 mile radius, SINGLE to receive only your county information or MULTIPLE

option permits alert signals for up to 9 pre-programmed locations only.

To select ALL locations in your area:

???Press ???or ???button to select ALL from the internal list

???When ALL is displayed in the window, press MENU/SELECT button to confirm ALL locations

???Press ??? to exit location programming

To select a Single location, SAME alert signals for only one programmed location:

???Press ???or ???button to select SINGLE from the internal list

???Press MENU/SELECT button to confirm single location

???Press MENU/SELECT button ??? the message EDIT? will be displayed. You can now select to edit or delete a single location

???Press MENU/SELECT button to select EDIT or DELETE. If you want to edit the county location, press ??? after county name is displayed.

???Press ???or ???button to select a new state and county from the internal list

???Press MENU/SELECT button to select and confirm the setting

???Press ??? to exit

To select Multiple locations, up to 9 stored locations:

???Press ???or ???button to select MULTIPLE from the internal list

???Press MENU/SELECT button to confirm

???Press ???or ???button to view the 9 EMPTY memory locations

???Press MENU/SELECT button ??? the message EDIT? will be displayed. You can now select to edit (add) or delete a single county location

???Press ???or ???button to select: EDIT? or DELETE?

???Press MENU/SELECT button and select EDIT If you want to add or change a location.

???Press ???or ???button selecting a state

???Press MENU/SELECT button

???Press ???or ???button selecting a county

???Press MENU/SELECT button to select and confirm the setting. Repeat above steps as many times as desired, to fill up to 9 or fewer locations

???Press ??? to exit

NOTE: The Weather Radio may miss alerts while being programmed. When selecting an empty location after adding a specific county or area to the memory, press??? once to select a county from a

1314

previously selected state. Press ??? again to select another state. The Weather Radio will also permit FIPS code updates to the location name. If the new entered FIPS code does not match the NOAA list, the message NOT FOUND will be displayed instead of the county name.

If ??? pressed when the cursor is at the farthest left digit of the FIPS code, your change will not be saved.

SIGNAL LOSS REMINDER

???Press MENU/SELECT button entering into the programming mode until SELECT CH message is displayed

???Press ???or ???button until the SIG REMINDER message is displayed

???Press MENU/SELECT button to activate it or deactivate the signal loss reminder - the unit will beep and display (???) when

NOTE: If the signal is lost, the SIGNAL LOSS message will appear with the reception icon [] flashing. The WARNING, WATCH and ADVISORY indicators will periodically flash. If the signal has been detected and lost within 10 minutes, no signal loss reminder will sound.

MISSED ALERT REMINDER PROGRAMMING

When the missed alert reminder is set for a TONE mode, your Weather Radio will beep every 30 seconds after the end of the alert broadcast, until the effective time of the alert will expire.

When missed alert reminder is set for a VOICE mode, a voice alert will broadcast for up to 5 minutes. Then radio will beep every 30 seconds until the effective time of the alert will expire.

???Press MENU/SELECT button entering into the programming mode until SELECT CH message is displayed

???Press ???or ???button until the ALT REMINDER message is displayed

???Press MENU/SELECT button to activate it or deactivate the alert loss reminder ??? the unit will beep and display a flashing speaker icon ((???)) when activated and a speaker icon when deactivated

???Press ??? to exit

NOTE: Press any button to mute the missed alert reminder

ALERT MODE SELECTION

There are two options available for the alert type ??? voice or tone.

If the VOICE option is selected, the alert sounds for 1o seconds and then the weather broadcast will turn on automatically for five (5) minutes. The Weather Radio display will reflect alert description and duration.

If the TONE option is selected, the alert tone will sound for five (5) minutes. The Weather Radio display will reflect an alert description and duration.

To mute the alert tone sooner, press WEATHER/SNOOZE button on the top of the main unit.

???Press MENU/SELECT button entering into the programming mode until ALERT MODE message is displayed

???Press ???button until the ALERT MODE message is displayed

???Press MENU/SELECT button entering into the alert type programming mode

???Press ??? or ??? selecting tone or voice

???Press MENU/SELECT button to confirm ??? the unit will beep once confirming the alert type selection

???Press ??? to exit

ACTIVATING OR DEACTIVATING AUDIBLE ALERTS

For activating audible alerts slide the ALERT ON/OFF (N) switch to ON position.

When alert is received, it will sound and the alert speaker sound icon ((???)) will appear on the display.

For deactivating audible alerts slide the ALERT ON/OFF (N) switch to OFF position ??? the radio will beep twice and the speaker icon with a line through it will appear.

NOTE: If the switch ALERT ON/OFF is in OFF position before unit is powered, the radio will still operate in ALERT ON mode until you slide ALERT ON/OFF to ON position and OFF again.

TESTING YOUR WEATHER RADIO

Every Wednesday between 11 AM and 1PM the NWS broadcasts a weekly test alert in the United States. To find out the specific test schedule in your area, contact your local NOAA or NWS office. On your

1516

Weather Radio these alerts are turned off. To change your alert settings, please see ALERT SELECTION section. For a list of NWS alerts see

APPENDIX 2.

WWVB RADIO CONTROLLED TIME

The NIST (National Institute of Standards and Technology) radio station (WWVB) is located in Ft. Collins, Colorado. It transmits an exact time signal continuously throughout the most of the continental United States at 60 KHz frequency. The Atomic Time Clock in your Weather Station can receive this WWVB signal through the internal antenna from up to 2,000 miles away. Due to the nature of the Earth???s ionosphere, reception can be limited during the daylight hours. The radio controlled clock will search for an alternate station that receives the atomic time signal from the NIST Atomic clock in Boulder, Colorado.

The WWVB tower icon on the unit???s display will flash indicating a radio signal reception from the WWVB station. If the tower icon is not fully lit, or if the time and date are not set automatically, please consider the following:

???During night-time hours, atmospheric disturbances are typically less severe and radio signal reception may improve. A single daily reception is sufficient enough to keep the clock accuracy within 1 second.

???Make sure the unit is positioned at 8 feet (2 meters) distance from any interference source such as a TV, computer monitor, microwave, etc.

???Within concrete wall rooms such as basements or office buildings, the received signal may be weakened. Always place the unit near the window for better reception.

Once the atomic time signal is received, the date and time will be set automatically, and the icon will appear.

NOTE: At the time of the initial reception allow at least 24 hours for the atomic time receiver to pick up the signal. In some cases, depending on the location, it may take up to 72 hours

If the initial reception was not successful and the time signal has not been received in this first 8 minutes, you may use the MODE button to set the time and date manually. (Refer to the MANUAL SETTINGS section). After the clock is set manually, place the main unit by the window for better reception. The atomic clock receiver is programmed that it will

continue to search for the atomic time signal daily for every hour between 1:00 am and 4:30 am.

Once the time signal has been successfully received, the time and date will be updated automatically.

To enable or disable the atomic time receiver:

???Press and hold UP - if atomic time reception is activated, a circular tower icon will start flashing next to the clock icon. If reception is disabled, the circular tower icon will disappear.

ATOMIC CLOCK

Immediately after batteries installation, the clock will beep and display all available LCD segments for a moment. Immediately after the atomic time signal receiver will start searching for the atomic time signal. It usually takes between 5-8 minutes.

NOTE: Do not press any buttons on the unit during auto search as it may interrupt product???s operation, and you will need to start the set up procedure again.

If the reception is successful and the atomic time signal is received, the date and time will be set automatically, and the icon will appear on the display.

NOTE: It is necessary to set your Time Zone, having in mind that the

1718

default zone is a Pacific Standard Time (PST). (Refer to a MANUAL SETTINGS section)

TEMPERATURE AND ALARM WINDOW

The Temperature and Alarm Window displays an indoor temperature and two time alarms. Press the MODE button to select among indoor temperature, Alarm 1 and Alarm 2. Press the ???/??? button to change the temperature unit between degree Celsius and degree Fahrenheit. (The default display is in degree Fahrenheit.)

TIME AND CALENDAR WINDOWS

The Atomic Clock displays time in an hour-minutes-seconds format in the Time Window located below the Temperature and Alarm Window. The date is displayed in month-date format next to the day of the week and moon phase icon in the Calendar Window.

MANUAL SETTINGS

If desired, the time, date and other available parameters can be programmed manually. It is necessary to set your Time Zone manually.

TIME ZONE

???Enter the US Time Zone programming mode by pressing and holding the UP button for 3 seconds.

???Keep holding UP button until the desired time zone (Pacific, Mountain, Central or Eastern) is highlighted on the unit???s display map in the Time Window

???Release the UP button and the desired Time Zone will be selected

CLOCK

???Press and hold MODE button for 3 seconds until the year digits in the Calendar Window will flash

???Press UP or DOWN adjusting a correct year

???Press MODE to confirm and move to the next parameter ??? the month digit will flash

???Press UP or DOWN adjusting the current month and then press MODE to confirm ??? the date digit will flash

???Press UP or DOWN adjusting the date and then press MODE to confirm ??? the ???M??? and ???D??? digits will flash

???Press UP of DOWN selecting the calendar display format in M/ D or D/ M - the hour digit will flash in the Time Window

???Press UP or DOWN adjusting the hour and then press MODE to confirm ??? the minutes will flash

???Press UP or DOWN adjusting the minutes and then press MODE for the last time to confirm after the last parameter is set

DAY OF THE WEEK LANGUAGE

???Press and hold LANG button for 3 seconds to enter into the day of the week language programming mode: the default language abbreviation will appear (example ??? EN)

???Continue holding LANG button until the desired day of the week language abbreviation is displayed

???Release the LANG button and the day of the week will be displayed in selected language

1920

PROJECTION (PCR507W) Only

The Atomic Projection Clock is capable of projecting the information immediately, as well as continuously.

IMMEDIATE PROJECTION

???Press SNOOZE/LIGHT button once to project the current time image for five seconds.

???Press FLIP button to rotate projected image 180?? clockwise

???Press and hold FLIP button for 2 seconds again and the projected image will rotate between the time and indoor

temperature information every 5 seconds

CONTINUOUS TIME AND TEMPERATURE PROJECTION

???Connect AC/DC adapter provided to the AC adapter input

???Slide the CONTINUE PROJECTION switch to the arrow direction shown on the unit???s side: the current time will be projected on the wall or the ceiling continuously.

ALARM SETTING

The Atomic Clock Radio has two time alarms. If any of the alarms is activated, it will sound at the set time and the alarm icon will flash. Also, you can select the alarm in radio sound or beep sound by switching to the desired position.

BELL ALARM SETTING

???Slide the alarm switch to the ALARM position. The alarm icons of and will be shown on the display.

???Press MODE button to view the ALARM 1 or ALARM 2 modes. If the ALARM 1 is selected, the default time ???6:00??? with the AL label will be displayed. If the ALARM 2 is selected, the default time???8:00???with the AL 2 label will be displayed

???Press and hold the MODE button for two seconds - the hour digit will flash

???Enter the hour parameter by using DOWN or UP button

???Press the MODE button again, then the minute digits will flash

???Enter the minutes parameter by using DOWN or UP button

???Press the MODE button one last time to confirm the setting.

???Use the same procedure for setting the time for ALARM 2

RADIO ALARM SETTING

???Slide the alarm switch to the RADIO position. The alarm icons of and will be shown on the display.

???Press and hold the MODE button for 3 seconds - the hour digit

2122

will flash and the radio display will be on.

???Press STATION button to select the station that you want to be your wake up station

???Enter the hour parameter by using DOWN or UP button

???Press the MODE button again, then the minute digits will flash

???Enter the minutes parameter by using DOWN or UP button

???Press the MODE button one last time to confirm the setting.

???Use the same procedure for setting the time for ALARM 2

HOW TO STOP AN ALARM

???Slide the alarm switch to the OFF position, alarms will be disabled and the alarm icons will disappear from the display.

DIGITAL FM RADIO

The band range of FM Radio is operated from 87.5 to 108.1 MHz.

GENERAL OPERATION

???Press RADIO button (On top) to turn on the radio. The current frequency selection will be shown on the LCD display.

???Rotate TUNNING knob (side) to select the desired radio station. Each step of rotation will increase or decrease the frequency by 0.05MHz. Rapid rotation of TUNNING knob will jump to the next closest station automatically.

???Rotate VOLUME knob to adjust the desired volume. There are total 15 steps of volume. The midrange default value is 6.

???If the reception is weak, extend the antenna to improve the reception.

???Press RADIO button to turn off the radio. The radio functions will automatically turn off when the low battery indicator displayed, unless connected to the AC adapter.

RADIO STATION PROGRAM SETTING

Your favorable station can be set in the radio station program. Quick searching of radio station can be done by selection of preset station number.

???Press RADIO button once to turn on the radio.

???Rotate TUNNING knob to search the desired radio station.

???Press MEMORY button until the station number is flashing on the display.

???Press STATION button to select the desired station number. There are total 18 stations can be set in the program.

???Press MEMORY button once more to confirm

???Then, you can press STATION button only to find your preset favorable radio station.

SLEEPING MODE SETTING

You can use sleeping mode turn off the radio automatically.

???Press SLEEP button to activate sleeping mode. ???SLEEP??? will flash when the sleep mode is activated.

???Press SLEEP again to select the radio shut down time from 5 to 90 minutes maximum. Each press of SLEEP button decreases the shut down time by 5 minutes. The default value is 90 minutes.

???After setting, the display will change back to station frequency. The radio will shut down automatically when the pre-set time is reached.

???Press LIGHT/ SNOOZE button to stop sleeping mode and radio will turn off automatically.

2324

HEADPHONE SPEAKERS

Headphone can be used when you connect the headphone (not included) into the headphone jack. This jack can also support computer style speakers and provide additional volume control for the weather radio, if desired.

SNOOZE & BACKLIGHT

Press the SNOOZE/LIGHT button to temporarily stop any alarm. After the SNOOZE /LIGHT button is depressed, the alarm sound will resume in the programmed snooze period and the blue backlight will be activated for 5 seconds. If the alarm is not disabled after that, it will sound for four more minutes and then will stop by itself. There is no continuous back light.

PRECAUTIONS

This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions:

???Do not immerse the unit in water.

???Do not clean the unit with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits.

???Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts.

???Do not tamper with the unit???s internal components. Doing so will invalidate the warranty and may cause damage. The unit contains no user-serviceable parts.

???Use only fresh batteries. Do not mix new and old batteries.

???Read the user's manual thoroughly before operating the unit.

APPENDIX 1 ??? CITY CODES

US and Canadian Cities

SPECIFICATIONS

Weather Radio

Radio Frequency Band: from 162.400MHz to 162.500MHz

Operating Range: about 40 miles (65 km) radius

Channels: Digital PLL tuning for 7 NOAA channels

SAME programming: All, MULTIPLE (for 9 counties) or SINGLE

Volume: 16 levels

Receiving Sensitivity: 100 db V/m

FIPS/CLC Codes Sensitivity: 0.5 u/V

Signal to Noise Ratio: 45 dB

Channel Selectivity: 50 dB

Digital Radio

FM frequency: 87.5 to 108 MHz at step frequency 50 KHz

Volume step: 15 (Digital: 0-15, default: 6)

Max. Stored Stations: 18

Time

12/24 hour display in hh: mm format

Date format: month ??? day User-selectable US Time Zone

Day of the week: Selectable: English, Spanish or French Languages Dual 4 minutes crescendo alarm with programmable snooze

Indoor Temperature

Operating range: -5.0??C to +50.0??C/23.0??F to 122.0??F

Temperature resolution: 0.1??C/0.2??F User-selectable (F?? or C??) temperature display LED backlight: 5 seconds

Low battery indicator

Projection (PPCR507W)

Focus adjustment

180?? projected image rotation and flip

Power

6 AA size (UM-3) 1.5V batteries (not included) AC/DC adapter - 9V, 120mA (included)

Dimensions

(PCR507W) 8.9(L) x 6.26(H) x 2.32(D) inches (RN507W) 8.9(L) x 6.26(H) x 2.32(D) inches

3132

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user???s authority to operate the equipment.

NOTE: This equipment had been tested and found to comply with the limits for a Class B Digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment, installed and used in accordance with the instructions, may cause harmful interference to radio communications.

There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to improve or correct turning the interference by one or more of the following measures:

???Reorient or relocate the receiving antenna

???Increase the separation between the equipment and receiver.

???Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

???Consult the dealer or an experienced radio / TV technician for help.

DECLARATION OF CONFORMITY

Name: Hideki Electronics, Inc.

Address: 7865 SW Mohawk, Tualatin, OR 97062

Telephone No.: 1 503 612 8395 declare that the product Product No.: PCR507W

Product Name: Honeywell Public Alert Projection Clock Radio

Manufacturer: Hideki Electronics Ltd.

Address: Unit 2304-06, 23/F Riley House, 88 Lei Muk Road, Kwai Chung, New Territories, Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

STANDARD WARRANTY INFORMATION

This product is warranted from manufacturing defects for one year from the date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair.

Note that online product registration is required to ensure valid warranty protection.

To register your product, go to our Company website at: www.honeywellweatherstations.com. Click Online Product Registration under the Customer Service menu.

Should you require assistance with this product and its operation, please contact our Customer Service Hotline 1(866) 443 3543.

Please direct all returns to the place of the original purchase. Should this not be possible, contact Hideki Customer Service Hotline for assistance and to obtain a Return Merchandise Authorization (RMA). Returns without a return authorization will be refused. Please retain your original receipt as you may be asked to provide a copy for proof of purchase.

Hideki Electronics, Inc. reserves the right to repair or replace the product at our option.

Honeywell International Inc. makes no representations or warranties with respect to this product.

All user manual contents and information are subject to change.

3334