1.KEEP GUARDS IN PLACE and in working order.

2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.

3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4.NEVER USE IN DANGEROUS ENVI- RONMENT. Do not use power tools in damp or wet locations, or where any flam- mable or noxious fumes may exist. Keep work area well lighted.

-2-

5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.

7.NEVER FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

8.USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

G1013 Combination Sander

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace exten- sion cords if they become damaged.

Minimum Gauge for Extension Cords

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safe- ty glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It???s safer than using your hand and frees both hands to operate tool.

13.NEVER OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in.

17.USE RECOMMENDED ACCESSORIES.

Consult the owner???s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.

20.NEVER USE UNDER THE INFLUENCE of alcohol or drugs, or when tired.

21. NEVER ALLOW UNSUPERVISED OR

UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to the operation of the machine are approved, correct, safe, and clearly understood.

1.BE AWARE OF BELT or disc rotation when sanding.

2.KEEP FINGERTIPS AWAY from the mov- ing belt or disc. Serious injury could result if skin contacts abrasives or moving parts.

3.NEVER USE EXCESSIVE FORCE when sanding. Doing this greatly increases the chances of personal injury and motor over- load.

4.ALWAYS FEED THE WORK against the direction of rotation.

5.EVEN IF YOU HAVE A reliable method of dust collection, use a dust mask or respira- tor when sanding, as well as eye and ear protection.

6.IF THERE IS ANY doubt as to the stability or integrity of the material to be sanded, don???t sand it.

7.DO NOT OPERATE SANDER with a dam- aged or badly worn disc or belt.

8.WHEN DISC SANDING, feed material into the portion of the disc spinning down toward the table.

9.TIE BACK LONG HAIR and remove any loose-fitting clothing or jewelry that could be caught up in the sander???s disc, belt, or other moving machine parts.

10.HABITS ??? GOOD OR BAD ??? are hard to break. Develop good habits and safety will become second nature to you.

Like all power tools, there is danger asso- ciated with the Model G1013 Combination Sander. Accidents are frequently caused by lack of familiarity or failure to pay atten- tion. Use this tool with respect and cau- tion to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glass- es or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI).

No list of safety guidelines can be com- plete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equip- ment or poor work results.

The Model G1013 is wired for 110V, single-phase operation only. The 1???2 H.P. motor will safely draw 12 amps at 110V. If you operate this sander on any circuit that is already close to its capacity, it might blow a fuse or trip a circuit breaker. However, if an unusual load does not exist and a power failure still occurs, contact a qualified elec- trician or our service department.

Fusing

A 15-amp fuse or circuit breaker should be used when fusing this combination sander. Circuit breakers rated any higher are not adequate to protect the circuit from power surges.

In the event of an electrical short, grounding reduces the risk of electric shock by providing a path of least resistance to disperse electric cur- rent. This tool is equipped with a power cord hav- ing an equipment-grounding conductor. See Figure 1. The outlet must be properly installed and grounded in accordance with all local codes and ordinances.

This equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually ground- ed. If it is not, it will be necessary to run a separate 12 A.W.G. copper grounding wire from the outlet to a known ground. Under no circumstances should the grounding pin from any three-pronged plug be removed. Serious injury may occur.

Extension Cords

If you find it necessary to use an extension cord with the Model G1013, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord. The extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords when they become worn or damaged.

Figure 1. Grounded plug configuration.

Commentary

We are proud to offer the Grizzly Model G1013 Combination Sander. The Model G1013 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly???s commitment to customer satis- faction.

The Model G1013 is a combination 1" x 42" belt and 8" disc sander that is capable of a wide vari- ety of operations. The 1" wide belt enables you to sand small or finely-detailed pieces as well as the inside areas of closed loops. With the 8" disc and table, larger surfaces can be sanded at many dif- ferent angles. The Model G1013 comes complete with motor and electrical package.

A number of sanding discs and belts for the Model G1013 are available through the Grizzly catalog.

We are also pleased to provide this manual with the Model G1013. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. It repre- sents our effort to produce the best documenta- tion possible. If you have any comments regard- ing this manual, please write to us at the address below:

Grizzly Industrial, Inc.

C/O Technical Documentation

P.O. Box 2069

Bellingham, WA 98227-2069

Most importantly, we stand behind our machines. If you have any service questions or parts requests, please call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 326-3806

Fax: (800) 438-5901

E-Mail: techsupport@grizzlyindustrial.com

Web Site: http://www.grizzlyindustrial.com

The specifications, drawings, and photographs illustrated in this manual represent the Model G1013 as supplied when the manual was pre- pared. However, owing to Grizzly???s policy of con- tinuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Whenever possible, though, we send manual updates to all owners of a particular tool or machine. Should you receive one, we urge you to insert the new information with the old and keep it for reference.

Read the manual before assembly and operation. Become familiar with the machine and its operation before begin- ning any work. Serious personal injury may result if safety or opera- tional information is not understood or followed.

Unpacking

This Combination Sander is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you???ve signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier. Save the containers and all packing materials for possible inspection by the carrier or its agent. Without the packing materials, filing a freight claim can be difficult. If you need assis- tance determining whether you need to file a freight claim, or with the procedure to file one, please contact our Customer Service.

When you are completely satisfied with the con- dition of your shipment, you should inventory its parts.

Figure 2. Overview of parts.

Parts Inventory

After all the parts have been removed from the carton, you should have:

??? Belt Guard

??? Disc Guard

??? Disc Table

??? Bolt Bag

??? Table Support

??? Sanding Unit

??? Motor

??? Miter Gauge

??? Belt Table

??? V-Belt

??? Base

??? Aluminum Disc

??? Disc Sanding Paper

??? Motor Pulley

NOTICE

A full parts list and breakdown drawing can be found toward the end of this manual. For easier assembly, or to identify missing parts, please refer to the detailed illustra- tions at the end of the manual.

Clean Up

The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship- ment. Remove this protective coating with a sol- vent cleaner or citrus-based degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usage instructions on the prod- uct you choose for clean up.

Do not use gasoline or other petroleum-based solvents to clean with. They have low flash points which make them extremely flammable. A risk of explosion and burning exists if these products are used . Serious personal injury may occur.

Do not smoke while using solvents. A risk of explo- sion or fire exists and may result in serious personal injury.

Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingest- ed. Always work in well- ventilated areas far from potential ignition sources when dealing with sol- vents. Use care when dis- posing of waste rags and towels to be sure they do not create fire or environ- mental hazards.

G1013 Combination Sander

Site Consideration

BENCH LOAD

Your Model G1013 Combination Sander repre- sents a relatively large weight load in a small foot- print. Be sure that you workbench is adequately reinforced to support the weight of the sander.

WORKING CLEARANCES

Working clearances can be thought of as the dis- tances between machines and obstacles that allow safe operation of every machine without limitation. Ensure that your working area offers plenty of room for free movement and a substan- tial amount of distance between you and others that may be working in your shop area.

LIGHTING AND OUTLETS

Lighting should be bright enough to eliminate shadow and prevent eye strain. Electrical circuits should be dedicated or large enough to handle combined motor amp loads. Outlets should be located near each machine so power or exten- sion cords are not obstructing high-traffic areas. Be sure to observe local electrical codes for prop- er installation of new lighting, outlets, or circuits.

Make your shop ???child safe.??? Ensure that your workplace is inaccessible to children by closing and locking all entrances when you are away. Never allow visitors in your shop when assembling, adjusting or operating equip- ment.

-9-

Do not connect power to the machine when per- forming any assembly. Failure to do this may result in serious person- al injury.

Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury.

Overview

The majority of your Combination Sander has been assembled at the factory. The few remain- ing pieces will go together quickly and should be done in the following order:

1.Feet to Base

2.Sanding Unit to Base

3.Table Support to Base

4.Motor to Base

5.Motor Pulley to Motor Shaft

6.V-Belt to Pulleys

7.Belt Guards to Sanding Unit

8.Aluminum Disc to Motor Shaft

9.Tables to Sanding Unit

10.Wiring motor

Only a few common tools are required to assem- ble your Combination Sander. Specifically, these are: 6" adjustable wrench, 10mm open end wrench, 12mm open end wrench, Phillips?? head screwdriver, 3mm Allen?? wrench (supplied with machine), and a rubber mallet.

-10-

Assembly Process

Assemble as follows:

1.Attach the four (4) rubber feet to the base using the four (4) 1???4" - 20 x 1" hex bolts, four

(4) 1???4" flat washers and four (4) 1???4" - 20 hex nuts. Be sure that the bolts protrude upward through the base. See Figure 3.

Figure 3. Order of foot attachment.

2.Place the preassembled Sanding Unit onto the Base as shown in Figure 4. Secure with the four (4) 5???16" - 18 x 3???4" hex bolts, eight (8)

5???16" flat washers, and four (4) 5???16" - 18 hex nuts.

Figure 4. Sanding unit mounted on base.

G1013 Combination Sander

3.Attach the Disc Table Support to the base using the four (4) 5???16" - 18 x 11???4" hex bolts, eight (8) 5???16" washers, and four (4) 5???16" - 18 hex nuts. See Figure 5. Finger tighten for now.

Figure 5. Table support mounted on base.

4.Mount the Motor to the base using the four

(4) 5???16" - 18 x 5???8" carriage bolts, four (4) 5???16" washers, and four (4) 5???16" - 18 hex nuts. Be sure that the bolts protrude upward through the motor base. See Figure 6. Finger tighten only.

Figure 6. Motor mounted on base.

G1013 Combination Sander

5.Install the Motor Pulley onto the Motor Shaft. Lightly tap into place with a rubber mallet if necessary. Align the keyways on each and insert the 3???16'' square key. Secure with a 1???4" - 20 x 3???8'' setscrew. See Figure 7.

Figure 7. Motor pulley attachment.

6.Place the V-Belt onto the pulleys.

7.Set a straightedge across the edge of both pulleys and adjust the position of the motor to correct the pulley alignment. The straight- edge should evenly touch each pulley when they are aligned. See Figure 8.

Figure 8. Inspecting pulley alignment.

-11-

8.Move the motor back to set the belt tension. The belt should deflect about 1???2" per side when squeezed in the middle with moderate pressure. Tighten the motor down when ten- sion is correct.

Figure 9. Belt guard attached to sander.

9.Attach the belt guards as shown in Figure 9. Secure with four (4) M5-0.8 x 6mm Phillips?? head screws and 5mm washers.

10.Install the belt table using the 5???16" - 18 x 5???8" carriage bolt, 5???16" fender washer and 5???16" - 18 hex nut. See Figure 10.

Figure 10. Belt table attached to sander.

11.Slide the 8'' aluminum disc onto the motor shaft. Lightly tap into place with a rubber mallet if necessary. Align the disc and motor shaft keyways and insert the 3???16'' square key. Secure the disc with a 1???4" - 20 x 3???8'' setscrew.

See Figure 11.

Figure 11. 8" disc attached to motor.

12.Peel the backing from the new sanding disc paper and stick it to the Aluminum Disc.

13.Secure the Disc Table to its support bracket using the two (2) 1???4" - 20 x 11???4" carriage bolts, two (2) 1???4" flat washers and two (2) 1???4" - 20 wing nuts. See Figure 12.

Figure 12. Disc table attachment.

14.Align the table so that there is a 1???16'' gap between the 8" disc and the table. See Figure 13. Tighten the bolts that secure the table support bracket to the base.

1???16" Gap

15.Wire the motor by removing the motor junc- tion box cover and feed the power cord from the switch through the plastic grommet at the bottom of the junction box. Connect the wires according to the Wiring Diagram Insert included with this manual. If this insert is missing, contact the appropriate service cen- ter listed in the Introduction for a replace- ment. See Figure 14.

Figure 13. Table aligned with sanding disc.

DO NOT attempt to connect or adjust wiring with the cordset plugged into its power source. Serious danger of electrocution could result.

Figure 14. Cordset connection at motor.

With the exception of belt tracking, adjust- ments to your Sander should be made with the power off and the machine unplugged!

Belt Tracking

The idler and drive rollers are slightly crowned to keep the belt centered on the rollers. This will not correct improper tracking. Tracking must be peri- odically adjusted (particularly after belt replace- ment) to keep the belt properly aligned to the rollers and the platen. To adjust tracking:

1.Unplug the machine!

2.Remove the Sanding Belt Table and Sanding Belt Guards.

2.Turn the 8'' disc by hand to observe lateral belt drift. DO NOT turn the sander on to inspect for belt drift.

3.By sight, center the Sanding Belt by adjust- ing the tracking knob. See Figure 15.

Lock Knob

Tracking Knob

Figure 15. Location of tracking adjustments.

-14-

4.Move hands away from 8'' disc.

5.Plug sander into power and turn machine on and off quickly. Inspect tracking.

6.Repeat steps 1-5 until the belt is centered on the rollers.

If the belt tracks properly on the two front rollers, but not on the rear roller, the rear roller must be adjusted. The roller shaft axle is slightly bent. By turning the axle, belt tracking will be affected.

1.Turn off the sander and disconnect it from its power source.

2.Remove rear belt guard.

3.Using a 10mm wrench, turn the rear axle nut. See Figure 16.

4.Keep rotating by hand until the sanding belt rides in the center of the roller.

5.Replace the rear belt guard.

Rear Axle Nut

Figure 16. Adjusting rear axle.

G1013 Combination Sander

Belt Table Tilt

Once you have turned off the switch and discon- nected the sander from its power source:

1.Loosen the hex nut as shown in Figure 18.

2.Tilt the table to the desired position.

3.Tighten the hex nut.

Figure 18. Belt table in tilted position.

Belt Replacement

Once you have turned off the switch and discon- nected the sander from its power source:

1.Remove the two Sanding Belt Guards.

2.Press down on the top arm to release the belt tension and remove the old belt. See

Figure 17.

Note: you may find it easier to remove and replace the belt with the belt table either tipped down to 45?? or completely removed.

3.Install new belt. Arrows on underside of the belt should point in the direction of roller travel. If your belt has no arrows, install it so that the overlap on the seam travels down- ward (when facing the machine). Otherwise the paper will catch on your stock and rip. Release the arm.

4.Replace the Sanding Belt Guards.

Figure 17. Sanding belt removal.

Disc Table Tilt

Once you have turned off the switch and discon- nected the sander from its power source:

1.Loosen the two wing nuts under the sanding disc table. See Figure 19.

2.Tilt the table to the desired position.

3.Tighten the wing nuts.

Figure 19. Disc table in tilted position.

Disc Replacement

Once you have turned off the switch and discon- nected the sander from its power source:

1.Remove the Sanding Disc Table.

2.Peel off the old Sanding Disc. Remove the backing from the new Disc, center it and press it firmly into place.

3.It may become necessary to remove the Aluminum Disc from the Motor Shaft because the Sanding Disc cannot be peeled off or the Aluminum Disc requires cleaning. Do not use petroleum-based solvents to clean the surface of the aluminum disc. This adversely affects adhesion.

Keep loose clothing out of the way of machinery and keep hair pulled back.

Wear safety glasses dur- ing all operations on the shaper. Failure to com- ply may result in serious personal injury.

Always wear a dust mask when operating the sander. Using this machine produces saw- dust which may cause allergic reactions or res- piratory problems.

Disconnect power to the machine when perform- ing any adjustments or maintenance. Failure to do this may result in seri- ous personal injury.

Test-Run

Before you put your Combination Sander into use, give it a quick inspection with the machine switched off and disconnected from its power source.

1.Are all fasteners tight?

2.Is the sanding belt properly tracked and ten- sioned?

3.Rotate disc slowly by hand. Look and listen for any scraping noises or anything that impedes smooth movement. Make appropri- ate adjustments before attempting to run the machine.

4.If the sander appears to be free of problems that might affect its operation, plug it in to its power source and start the machine. Be sure to keep a finger on the OFF button, just in case of a problem with the machine. Run the sander briefly to allow inspection of belt tracking.

5.Turn off the machine, disconnect it from its power source, and re-inspect for loose fas- teners. If the tracking is not correct, refer to the tracking adjustment guidelines in the

Adjustments section.

Never use the Model G1013 for applications other than those for which it was made. DO NOT overload the machine or use excess force when sanding. Severe personal injury, damage to the machine, or damage to your workpiece could occur.

For general wood sanding, position and secure table, turn the machine on, and slowly feed your workpiece into the belt or disc. For disc sanding, note the direction of the disc rotation and be sure to feed your workpiece into the disc???s downward spin. Also, be sure to keep the work table about 1???16" away from the belt or disc.

Remove platen and move Small Upper Idler Roller rearward so the workpiece will not be acci- dentally forced against it. Slowly feed the work- piece into the belt; the belt will follow the contour of the workpiece. See Figure 20.

Figure 20. Contour sanding.

Inside Sanding

To sand or grind an interior work area, the sand- ing belt must be fed through the workpiece and remounted on its rollers. Depending on your application, you may either remove the platen or keep it in place.

1.Remove the Belt Sanding Table and the Belt Guards.

2.Feed the Sanding Belt through the work- piece and over the Upper Idler Roller. Loosen the Small Upper Idler Roller, swing it toward the front of the machine, and feed the belt around the pulley.

3.Press down on the top arm and feed the remainder of the belt through the rollers as shown in Figure 21.

4.Replace guards and table.

5.Adjust belt tracking as described in

Adjustments section.

Figure 21. Belt arrangement for inside sanding.

Sharpening

Tilt the table to the desired sharpening angle and secure it. Using C-Clamps, attach a suitable wood scrap to the table. See Figure 22. This acts as an auxiliary table to support the workpiece. This table should be 1???16" away from the belt. It may be necessary to cut a notch in your auxiliary table to achieve this clearance.

Figure 22. False table for sharpening support.

Disconnect power to the machine when perform- ing any adjustments or maintenance. Failure to do this may result in seri- ous personal injury.

General

Make a habit of inspecting your sander each time you use it. Check for the following conditions and repair or replace when necessary.

1.Loose mounting bolts.

2.Worn switch.

3.Worn or damaged cords and plugs.

4.Worn or damaged V-belt.

5.Poor belt tensioning ??? tracking.

Table

The working table and other non-painted sur- faces on the Model G1013 should be protected against rust and pitting. Wiping the sander clean after every use ensures that sawdust is not allowed to trap moisture against bare metal sur- faces.

Tables can be kept rust-free with regular applica- tions of products like Boeshield?? T-9. For long term storage you may want to consider products like Kleen Bore's Rust Guardit???.

Lubrication

Your combination sander is equipped with shield- ed and pre-lubricated ball bearings that require no lubrication for the life of the bearings. All bear- ings are common sizes and are readily available from a local bearing supply house or our Service Department. The roller shafts, however, will ben- efit from regular applications of light machine oil.

See Figure 23.

Figure 23. Lubrication points.

The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G1013 Combination Sander.

If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service technicians will be glad to help you.

If you have comments dealing specifically with this manual, please write to our Bellingham, Washington location using the address in Section 3: Introduction. The specifications, drawings, and photographs illustrated in this manual represent the Model G1013 as supplied when the manual was prepared. However, due to Grizzly???s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Whenever possible, though, we send manual updates to all owners of a particular tool or machine. Should you receive one, add the new information to this manual and keep it for refer- ence.

We have included some important safety mea- sures that are essential to this machine???s opera- tion. While most safety measures are generally universal, Grizzly reminds you that each work- shop is different and safety rules should be con- sidered as they apply to your specific situation.

Operating this equipment has the potential to launch flying debris which could cause eye injury. Always wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI).

We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3: Introduction.

Additional information sources are necessary to realize the full potential of this machine. Trade journals, woodworking magazines, and your local library are good places to start.

The Model G1013 was specifically designed for sanding operations only. DO NOT MOD-

IFY AND/OR USE THIS MACHINE FOR ANY OTHER PURPOSE. Modifications or improper use of this tool will void the war- ranty. If you are confused about any aspect of this machine, DO NOT use it until you have answered all your questions. Serious personal injury may occur.

Like all power tools, there is danger associ- ated with the Model G1013 Combination Sander. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

1.How did you learn about us?

___Other__________________________________________________

2.Which of the following magazines do you subscribe to.

___Other__________________________________________________

3.Which of the following woodworking/remodeling shows do you watch?

___Other__________________________________________________

4.What is your annual household income?

5.What is your age group?

6.How long have you been a woodworker?

7.How would you rank your woodworking skills?

8.What stationary woodworking tools do you own? Check all that apply.

___Other__________________________________________________

9.How many of your woodworking machines are Grizzly? _____________

10.Which benchtop tools do you own? Check all that apply.

___Other__________________________________________________

11.How many of the machines checked above are Grizzly? ____________

12.Which portable/hand held power tools do you own? Check all that apply.

___Other__________________________________________________

13.What machines/supplies would you like Grizzly Industrial to carry?

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

14.What new accessories would you like Grizzly Industrial to carry?

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

15.What other companies do you purchase your tools and supplies from?

__________________________________________________________

__________________________________________________________

16.Do you think your purchase represents good value?

17.Would you recommend Grizzly Imports to a friend?

18.Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times.

19.Comments:_________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

CUT ALONG DOTTED LINE