MANUAL INSERT
Model G1029Z
2.5 Micron 2 HP
Dust Collector
INTRODUCTION
The Model G1029Z is the same dust collector as the Model G1029, but with the upgrade of the 2.5 micron top bag.
For the Model G1029Z, please follow all safety, adjustment, and operation instructions from the Model G1029 instruction manual.
INVENTORY
The Model G1029Z is shipped with the same parts shown in the Model G1029 instruction manual, except for the 2.5 micron top filter bag.
REPLACEMENT PARTS
All replacement parts for the Model G1029Z are the same as the Model G1029, except for the 2.5 micron top bag. Therefore, please refer to the included Model G1029 manual when ordering new parts, unless you need to order a replacement 2.5 micron top bag for your machine, which is listed below.
If you need additional help with this machine, call our service department at: (570)
COPYRIGHT ?? NOVEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR5871 REVISED OCTOBER, 2004. PRINTED IN TAIWAN
DUST COLLECTOR
MODEL G1028Z/G1029
INSTRUCTION MANUAL
COPYRIGHT ?? 1991 BY GRIZZLY IMPORTS, INC.REG # TX 3170576
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.
REVISED FEBRUARY, 2002. PRINTED IN TAIWAN
WARNING
Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
???Lead from
???Crystalline silica from bricks, cement, and other masonry products.
???Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to fil- ter out microscopic particles.
SECTION 1: SAFETY
For Your Own Safety Read Instruction Manual Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools
1.KEEP GUARDS IN PLACE and in working order.
2.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.
3.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4.DO NOT USE IN DANGEROUS ENVI- RONMENT. Do not use power tools in damp or wet locations, or where any flam- mable or noxious fumes may exist. Keep work area well lighted.
5.KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.
6.MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
7.DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8.USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.
Safety Instructions For Power Tools Cont.
9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
Minimum Gauge for Extension Cords
10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts.
11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.
12.SECURE WORK. Use clamps or a vise to hold work when practical. It???s safer than using your hand and frees both hands to operate tool.
13.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.
14.USE RECOMMENDED ACCESSORIES.
Consult the owner???s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.
15.DO NOT
16.REDUCE THE RISK OF UNINTENTION- AL STARTING. On machines with mag- netic contact starting switches there is a risk of starting if the machine is bumped or jarred. Always disconnect from power source before adjusting or servicing. Make sure switch is in OFF position before recon- necting.
17.MANY WOODWORKING TOOLS CAN ???KICKBACK??? THE WORKPIECE toward the operator if not handled properly. Know what conditions can create ???kickback??? and know how to avoid them. Read the manual accom- panying the machine thoroughly.
18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.
20.NEVER OPERATE A MACHINE WHEN
TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Full mental alert- ness is required at all times when running a machine.
21.NEVER ALLOW UNSUPERVISED OR
UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to machine operation are approved, correct, safe, and clearly understood.
22.IF AT ANY TIME YOU ARE EXPERIENC- ING DIFFICULTIES performing the intend- ed operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed.
Additional Safety Instructions For
The Dust Collector
1.THIS DUST COLLECTOR IS TO BE USED
FOR WOOD DUST COLLECTION ONLY.
Do not use this dust collector to pick up liq- uids and metal scrap including, but not lim- ited to, nails and filings. Metallic debris will contact the spinning impeller and could spark. The spark could then cause a saw- dust explosion and severe fire hazard. Also, do not pick up material which cannot safely pass through the impeller such as solid wood scraps.
2.DO NOT PLACE YOUR HANDS OR TOOLS NEAR THE OPEN INLET during operation for any reason including, but not limited to, unclogging material and testing suction. The impeller could cause serious damage to body parts if touched while spin- ning.
3.PROBLEMS CONCERNED WITH ANY MOVING PARTS or accessories must be investigated and corrected with the power disconnected and after everything has come to a complete stop.
4.SUSPENDED DUST PARTICLES IN CON-
JUNCTION WITH AN IGNITION SOURCE, may cause an explosion. Do not operate the dust collector in areas where explosion risks would be high if dust were dispersed into the area. Areas of high risk include, but are not limited to, areas near pilot lights and/or open flames.
5.DO NOT ALLOW STEEL TO STRIKE
AGAINST STEEL WHICH MAY PRODUCE A SPARK. Sparks can smolder in wood dust for a long time before fire or flame is detected. If metal contacts metal during operation, immediately turn off the dust col- lector, unplug the power cord from the outlet or flip the disconnect switch and wait for all moving parts to stop. Remove collection bags and empty the dust into an approved air tight metal container in case of spark. Remedy the metal to metal contact problem before resuming operation.
6.WHEN EMPTYING DUST FROM THE COLLECTION BAGS, wear a respirator and safety glasses. Empty dust into an approved container and dispose of properly.
7.IF AT ANY TIME YOU ARE EXPERIENC-
ING DIFFICULTIES PERFORMING THE INTENDED OPERATION, stop using the machine! Then contact our service depart- ment or ask a qualified expert how the oper- ation should be performed.
8.BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC reaction in people and animals, especially when exposed to fine dust. Make sure you know what type of wood dust you will be exposed to in case there is a possibility of an allergic reaction. Always wear an approved respira- tor!
No list of safety guidelines can be com- plete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to follow guidelines could result in serious personal injury, damage to equipment or poor work results.
DO NOT use the dust collector for any other purpose besides collecting dust from con- nected woodworking machines. A dust col- lector should NEVER be used as an air cleaner. For safest use, wear a dust mask and use an air cleaner in addition to the dust collector.
SECTION 2: CIRCUIT REQUIREMENTS
The G1028Z Dust Collector is
A plug is not provided with the G1028Z. It will be necessary to purchase a standard 110V plug from your local hardware store. If you are rewiring for 220V, see Figure 1 for the recommended 220V receptacle.
Circuit Breaker: The 11???2 H.P. motor will draw roughly 18 amps at 110V or 9 amps at 220V. We recommend a using 20 amp circuit breaker for 110V or 220V operation. Circuit breakers rated higher will not adequately protect the circuit. If you are using a fuse, we recommend a 30 amp slow blow for 110V or 220V operation. Fuses rated higher will not adequately protect the circuit.
The G1029 Dust Collector is
A plug is not provided with the G1029. Refer to Figure 1 for recommended 220V receptacle.
Circuit Breaker: The 2 H.P. motor will draw roughly 12 amps @ 220V. We recommend using a 20 amp circuit breaker. Circuit breakers rated higher will not adequately protect the motor. If you are using a fuse, we recommend 30 amp slow blow 220V service. Fuses rated higher will not adequately protect the motor.
Figure 1. Recommended 220V receptacle.
In the event of an electrical short, grounding pro- vides electric current a path of least resistance to reduce the risk of electrical shock. This tool is equipped with an electric cord having an equip-
Improper connections of the
This equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. Under no cir- cumstances should the grounding pin from any
We do not recommend the use of extension cords with 220V equipment. Instead, arrange the place- ment of your equipment and the installed wiring to eliminate the need for extension cords. Should the situation be necessary to use an extension, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in Section 1: Safety Instructions to determine the minimum gauge for the extension cord when using either 110V or 220V. The extension cord must also con- tain a ground wire and plug pin. Always repair or replace extension cords when they become worn or damaged.
We have covered some basic electrical requirements for the safe operation of your machine. These requirements are not necessarily comprehensive. You must be sure that your particular electrical configu- ration complies with local and state codes. Ensure compliance by checking with your local municipality or a licensed electrician.
If you are unsure about the correct installation or modification of electrical circuits, please consult the advice of a qualified electrician. Failure to do so could result in serious personal injury.
SECTION 3: INTRODUCTION
Commentary
Grizzly Industrial, Inc. is proud to offer the Model G1028Z/G1029 Dust Collector. These dust col- lectors are a part of Grizzly???s growing family of fine machinery. When used according to the guidelines set forth in this manual, you can expect years of
The G1028Z/G1029 Dust Collector represents the
We are also pleased to provide this manual with the Model G1028Z/G1029. It was written to guide you through assembly, review safety considera- tions, and cover general operating procedures. It represents our effort to produce the best docu- mentation possible. If you have any comments regarding this manual, please write to us at the address below:
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA
Most important, we stand behind our machines. If you have any service questions or parts requests, please call or write us at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570)
Fax: (800)
The specifications, drawings, and photographs illustrated in this manual represent the Model G1028Z/G1029 as supplied when the manual was prepared. However, owing to Grizzly???s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Whenever possible, though, we send manual updates to all owners of a particular tool or machine. Should you receive one, we urge you to insert the new information with the old and keep it for reference.
Read the manual before assembly and opera- tion. Become familiar with the machine and its operation before begin- ning any work. Serious personal injury may result if safety or opera- tional information is not understood or followed.
Unpacking
The Model G1028Z/G1029 Dust Collector is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you???ve signed for delivery, please call Customer Service immediately for advice.
Save the containers and all packing materials for possible inspection by the carrier or its agent.
Otherwise filing a freight claim can be difficult.
When you are completely satisfied with the con- dition of your shipment, you should inventory its parts.
The G1028Z/G1029 is a heavy machine, 116/140 lbs. shipping weight. DO NOT
Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury.
Piece Inventory
After all the parts have been removed from the carton, you should have:
???Collector Body Assembly
???Base
??????Y??? Inlet
???Collection/Filter Bags
???Lower Support Brackets (2)
???Casters (4)
???Rubber Gasket
???Upper Support Bracket
???Outlet
???Outlet Hose
???Hose Clamps
???Hex Bolts
In the event that any
NOTICE
A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify missing parts, please refer to the detailed illustrations at the end of the manual.
Clean Up
The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or
Do not use gasoline or other
Do not smoke while using solvents. A risk of explo- sion or fire exists and may result in serious personal injury.
Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingest- ed. Always work in well- ventilated areas far from potential ignition sources when dealing with sol- vents. Use care when dis- posing of waste rags and towels to be sure they do not create fire or environ- mental hazards.
G1028Z/G1029 Dust Collector
Site Considerations
FLOOR LOAD
Your Model G1028Z/G1029 represents a moder- ate weight load in an average footprint. Most com- mercial or home shop floors should be sufficient to carry the weight of the Model G1028Z/G1029. If you question the strength of your floor, you can opt to reinforce it.
WORKING CLEARANCES
Working clearances can be thought of as the dis- tances between machines and obstacles that allow safe operation of every machine without lim- itation. Consider existing and anticipated machine needs, size of material to be processed through each machine, and space for auxiliary stands and/or work tables. Also, consider the relative position of each machine to one another for effi- cient material handling. Be sure to allow yourself sufficient room to safely run your machines in any foreseeable operation and keep dust collection hoses off the floor and out of the way.
LIGHTING AND OUTLETS
Lighting should be bright enough to eliminate shadows and prevent eye strain. Electrical circuits should be dedicated or large enough to handle combined motor amp loads. Outlets should be located near each machine so power or extension cords are not obstructing
Make your shop ???child safe.??? Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. Never allow visitors in your shop when assembling, adjust- ing or operating equip- ment.
SECTION 4: ASSEMBLY
Disconnect power to the machine when perform- ing any maintenance, assembly or adjust- ments. Failure to do this may result in serious personal injury.
Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.
Wear safety glasses dur- ing the entire assembly process. Failure to com- ply may result in serious personal injury.
Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury.
We have organized the assembly process into steps. Please follow along in the order presented here.
Tools Required: 12mm open end wrench, regu- lar and Phillips head screwdriver.
Position the base plate upside down and locate the casters so they are within easy reach. Mount the casters to the base plate using sixteen (16)
Figure 2. Mounting casters to base.
The collector body includes the fan assembly, switch, and motor which are preassembled at the factory. Set the collector body on top of the base plate so the intake portion is near the edge of the base plate and the bolt holes are lined up as shown in Figure 3. Secure the collector body to the base plate with four (4)
Figure 3. Mounting collector to base.
The outlet can now be attached to the main col- lector body. Insert the rubber gasket between the collector and lower outlet flange and secure using eight (8)
See Figure 4.
Figure 4. Mounting outlet to collector body.
There are two lower collector support brackets and one upper bag support bracket. Attach the collector brackets to the top edge of the base plate using four (4)
Figure 5. Mounting brackets to base.
The collector attaches to each support bracket. The inside of the collector is funnel shaped and directs the air around in a cyclone motion. Make sure that the inside taper (funnel) is faced down- ward and the collector inlet faces toward the col- lector body.
Secure the front support bracket to the collector with two (2)
Figure 6. Mounting collector to brackets.
Slip a loosened hose clamp over each end of the
Figure 7. Attaching flex hose.
1.Hook the top loop of the filter bag over the support bracket as shown in Figure 8.
Figure 8. Attaching filter bag.
2.Slip the top collection bag over the top edge of the collector and pull the strap tight to secure the bag as shown in Figure 9.
Figure 9. Securing collection bag.
3.Slip the steel band around the bag and tight- en down as shown in Figure 10.
Figure 10. Tightening steel band.
4.Slip the bottom collection bag over the bot- tom edge of the collector and pull the strap tight to secure the bag.
5.Place the steel band with the quick clamp over the bag and clamp on the tightest notch possible.
DO NOT force the clamp. Instead, choose the next notch over, then clamp in place.
Inlet
Press the ???Y??? inlet onto the inlet cover flange as shown in Figure 11. The inlet is secured to the collector body by a
Figure 11. Installing ???Y??? inlet.
SECTION 5: Designing The System
General
The Model G1028Z/G1029 can be operated as either a stationary or a mobile unit. There are advantages and disadvantages to both
The Model G1028Z/G1029 is designed to be a central dust collector system. Locate the dust col- lector in an out of the way location such as a cor- ner or separate room. The dust collector is capa- ble of collecting dust from up to two machines running simultaneously. Because of the large suction capacity of the Model G1028Z/G1029, great flexibility is possible in the planning and designing of your dust collection duct layout. Grizzly offers a complete line of dust collection accessories for setting up a stationary system. Additionally, Grizzly offers a complete guide book entitled Dust Collection Basics.
Whatever system you choose, always make sure there are no open flames or pilot lights in the same room as the dust collector. There is a risk of explosion if dust is dispursed into the air.
Material Selection
You have many choices regarding main line and branch line duct material. In most commercial workshops, the main line and branch lines are usually metal duct. Flexible hose is then used to connect each machine to the branch lines. In the case of small home shops, flexible hose may be used for both main line and branch line ducts. Plastic duct is also a popular material for home shops. Please be aware that there is a fire or explosion hazard if plastic duct material is used for dust collection without being grounded against static electrical charge
METAL DUCT
Metal duct comes in many varieties. Stove pipe, heating/ventilation duct and duct made especially for dust collection are all options. Advantages of metal duct is its conductivity and that it does not contribute to static electrical charge
FLEXIBLE HOSE
Flexible rubber hose, polyethylene, plastic flex- hose and other flexible ribbed hose is generally used for short runs, small shops and at rigid duct-
There are also many kinds of pure plastic flexible hose, such as
If using
PLASTIC DUCT
The popularity of plastic duct is due to the fact that it is an economical and readily available product. It is also simple to assemble and easily sealed against air loss. The primary disadvantage of plastic duct for dust collection, whether black ABS or white PVC and even rubber or polyethylene
System Grounding
Since plastic hose is abundant, relatively inexpen- sive, easily assembled and air tight, it is a very popular material for conveying dust from wood- working machines to the dust collector. We rec- ommend using flexible hose
To protect against static electrical build up inside a
If you connect the dust collector to more than one machine by way of a
Always guard against static electrical build up by grounding all dust collection lines.
Be sure that you extend the bare copper wire down all branches of the system. Do not forget to connect the wires to each other with wire nuts when two branches meet at a ???Y??? or ???T??? connec- tion.
Ensure that the entire system is grounded. If using plastic blast gates to direct air flow, the grounding wire must be jumped (Figure 12) around the blast gate without interruption to the grounding system.
Plastic Blast Gate
Figure 12. Ground jumper wire when using plastic blast gates and metal duct.
We also recommend wrapping the outside of all plastic ducts with bare copper wire to ground the outside of the system against static electrical build up. Wire connections at Y???s and T???s should be made with wire nuts.
Attach the bare ground wire to each stationary woodworking machine and attach the dust collec- tor frame with a ground screw as shown in Figure 13. Ensure that each machine is continuously grounded to the grounding terminal in your elec- tric service panel.
Figure 13.
Design Suggestions
When designing a successful dust collection sys- tem, planning is the most important step. Before you set out to run the first section of duct, consid- er these general guidelines for an efficient sys- tem:
1.Machines that produce the most saw dust should be placed nearest to the dust collec- tor. These machines include thickness plan- ers, shapers, sanders and bandsaws.
2.Ideally, you should design the duct system to have the shortest possible mainline run and to have short secondary branch ducts.
3.Directional changes should be kept to a min- imum. The more directional change fittings you use, the greater the loss of overall pres- sure.
4.Gradual directional changes are more effi- cient than sudden directional changes (i.e. use the largest corner radius possible when changing hose or pipe direction).
5.Each individual machine should have a blast gate to control suction from one machine to another.
6.The simpler the system, the more efficient and less costly it will be.
The best way to plan your new system is to draw a bird???s eye view (as shown in Figure 14) of your shop and sketch the following:
1.Your desired location of the dust collector, usually in a corner or along a wall.
2.The location of each machine in the system.
3.The location of the main line duct and each branch line.
4.The location of any obtrusion such as a joist or heating duct, that will require special duct routing.
Figure 14. Bird???s eye planning view.
SECTION 6: OPERATIONS
Test Run
Disconnect power to the machine when perform- ing any maintenance, assembly or adjust- ments. Failure to do this may result in serious personal injury.
Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.
Wear safety glasses dur- ing the entire operations process. Failure to com- ply may result in serious personal injury.
Always wear a dust mask when operating your dust collector. This machine circulates saw- dust which may cause allergic reactions or res- piratory problems.
Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine.
Turn on the power supply at the main panel. Press the START button. Make sure that your fin- ger is poised on the STOP button, just in case there is a problem. The dust collector should run smoothly, with little or no vibration or rubbing nois- es. Strange or unnatural noises should be investi- gated and corrected before operating the machine further.
If you cannot easily locate the source of an unusual noise or vibration, contact our service department for help.
General
Operating your Model G1028Z/G1029 is simple and straightforward. Blast gates located at each of the machines controls the air flow from the woodworking machine to the dust collector. If a machine is not being used, keep the blast gate closed to maintain higher levels of efficiency throughout the system.
DO NOT use the dust collector for any other purpose besides collecting dust from con- nected woodworking machines. A dust col- lector should NEVER be used as an air cleaner. For safest use, wear a dust mask and use an air cleaner in addition to the dust collector.
SECTION 7: MAINTENANCE
Disconnect power to the machine when perform- ing any maintenance, assembly or adjust- ments. Failure to do this may result in serious personal injury.
Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.
Wear safety glasses dur- ing the entire mainte- nance process. Failure to comply may result in serious personal injury.
General
Regular periodic maintenance on your Model G1028Z/G1029 Dust Collector will ensure its opti- mum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary:
1.Loose mounting bolts.
2.Worn switch.
3.Worn or damaged cords and plugs.
4.Any other condition that could hamper the safe operation of this machine.
5.Do not let collection bags get completely full.
Lubrication
Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them.
Bag Cleaning
Always wear a dust mask when changing the dust collection bags on the dust collector. Sawdust may cause allergic reactions or res- piratory problems.
Always empty the collection bags on a regular basis. Emptying the collection bags allows the machine to operate at a much higher level of effi- ciency.
Always wear the appropriate respirator or dust mask and safety glasses when emptying the col- lection bags. Small dust particles can escape the bags during emptying, causing them to become airborn and easily inhailed. This microscopic air- born dust is extremely unhealthy to breathe and can cause serious health problems.
While the Model G1028Z/G1029 excels at collect- ing the majority of wood dust produced by your machines, it is not an air filter; therfore, we strongly recommend the supplemental aid of a shop air filter such as the Grizzly G5955 or G9956. Air filters are designed to collect the smaller dust particles that a dust collector bags cannot trap.
SECTION 8: CLOSURE
The following pages contain general machine data, parts diagram, parts list and Warranty/Return information for your Model G1028Z/G1029 Dust Collector.
If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call the appropriate regional Service Department. Our trained service techni- cians will be glad to help you.
If you have comments dealing specifically with this manual, please write to our Bellingham, Washington location using the address in the Introduction. The specifications, drawings, and photographs illustrated in this manual represent the Model G1028Z/G1029 as supplied when the manual was prepared. However, due to Grizzly???s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly.
We have included some important safety mea- sures that are essential to this machine???s opera- tion. While most safety measures are generally universal, Grizzly reminds you that each work- shop is different and safety rules should be con- sidered as they apply to your specific situation.
Operating this equipment has the potential for flying debris to cause eye injury. Always wear safety glasses or goggles when oper- ating equipment. Everyday glasses or read- ing glasses only have impact resistant lens- es, they are not safety glasses. Be certain the safety glasses you wear meet the appro- priate standards of the American National Standards Institute (ANSI).
We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3 Introduction.
Additional information sources are necessary to realize the full potential of this machine. Trade journals, woodworking magazines, and your local library are good places to start.
The Model G1028Z/G1029 was specifically designed for dust collecting operation. DO
NOT MODIFY AND/OR USE THIS MACHINE FOR ANY OTHER PURPOSE. Modifications or improper use of this tool will void the warranty. If you are confused about any aspect of this machine, DO NOT use it until all your questions have been answered. Serious personal injury may occur.
Like all power tools, there is danger asso- ciated with the Model G1028Z/G1029. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.
WIRE DIAGRAM
110 VOLT
220VOLT
MACHINE DATA
SHEET
Customer Service #: (570)
GRIZZLY MODEL G1028Z/G1029 DUST COLLECTOR
Specifications, while deemed accurate, are not guaranteed.
26
14
20
23
2
21
27
35
24
14
38
4
19
28
11
10
8
2
9
7
1 2
23
22
2
6A (G1029)
6 (G1028Z)
5
29B
29A
4P1028004 BASE PLATE
5PS06 PHLP HD SCR
6P1028Z006 INLET COVER (G1028Z) 6A P1029006A INLET COVER (G1029)
7P1028007 CAP SCREW
8PB09 HEX BOLT
9P1028009 SPECIAL WASHER
10P1028010 10'' IMPELLER (G1028Z)
10P1029010 10'' IMPELLER (G1029)
11P1028011 COLLECTOR BODY
12PW07 FLAT WASHER 5???16"
17P1029017 MOTOR, 2 H.P. (G1029)
18PN02 HEX NUT
19P1028019 OUTLET
20P1028020 HOSE CLAMP
21P1028021 HOSE
22G1027 BAG, LOWER
23P1028023 COLLECTOR SUPPORT
24P1028024 COLLECTOR
25P1028025 PACKING (G1028Z)
25P1029025 PACKING (G1029)
26P1028026 UPPER BAG SUPPORT
27G1027 BAG, UPPER
28P1028028 GASKET
34PWRCRD220L MOTOR CORD
35P1028035 FILTER CLAMP
38 P1028Z038 QUICK RELEASE CLAMP
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly???s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly???s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe- cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a ???Return Number,??? which must be clearly posted on the outside as well as the inside of the car- ton. We will not accept any item back without this number. Proof of purchase must accompany the mer- chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
WARRANTY CARD
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone
MODEL # _____________________SERIAL #______________________Order #_________________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1.How did you learn about us?
___Other__________________________________________________
2.Which of the following magazines do you subscribe to.
___Other__________________________________________________
3.Which of the following woodworking/remodeling shows do you watch?
___Other__________________________________________________
4.What is your annual household income?
5.What is your age group?
6.How long have you been a woodworker?
7.How would you rank your woodworking skills?
8.What stationary woodworking tools do you own? Check all that apply.
___Other__________________________________________________
9.How many of your woodworking machines are Grizzly? _____________
10.Which benchtop tools do you own? Check all that apply.
___Other__________________________________________________
11.How many of the machines checked above are Grizzly? ____________
12.Which portable/hand held power tools do you own? Check all that apply.
___Other__________________________________________________
13.What machines/supplies would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
14.What new accessories would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
15.What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
16.Do you think your purchase represents good value?
17.Would you recommend Grizzly Industrial to a friend?
18.Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times.
19.Comments:_________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG