TA B L E O F C O N T E N TS

2012) (October 242292000

WARNING

Please read all instructions before using this refrigerator.

For your Safety

???DO NOT store or use gasoline, or other flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other hazards.

???DO NOT operate the refrigerator in the presence of explosive fumes.

???Avoid contact with any moving parts of automatic ice maker.

???Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.

Definitions

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

IMPORTANT

IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related.

Installation Checklist

Doors

???Handles are secure and tight

???Door seals completely to cabinet on all sides

???Freezer drawer is level across the top

Leveling

???Refrigerator is level, side-to-side and tilted ?? inch (6 mm) front-to-back

???Toe grille is properly attached to refrigerator

???Cabinet is setting solid on all corners

Electrical Power

???House power turned on

???Refrigerator plugged in

Ice Maker (select models)

???House water supply connected to refrigerator

???No water leaks present at all connections - recheck in 24 hours

???Ice maker is turned ON

Final Checks

???Shipping material removed

???Fresh food and freezer temperatures set

???Crisper humidity controls set

???Registration card sent in

Child Safety

Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to play. Cartons covered with rugs,

bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.

Proper Disposal of your Refrigerator or Freezer

Risk of child entrapment

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators or freezers are still dangerous ??? even if they will sit for ???just a few days???. If you are getting rid of your old refrigerator or freezer, please follow the instructions below to help prevent accidents.

Proper Disposal of Refrigerators/Freezers

We strongly encourage responsible appliance recycling/ disposal methods. Check with your utility company or visit www.energystar.gov/recycle for more information on recycling your old refrigerator.

Before you throw away your old refrigerator/ freezer:

??? Remove doors.

??? Leave shelves in place so children may not easily climb inside.

??? Have refrigerant removed by a qualified service technician.

IMPORTANT

CFC/HCFC Disposal

Your old refrigerator may have a cooling system that used CFCs or HCFCs (chlorofluorocarbons or hydrochlorofluorocarbons). CFCs and HCFCs are

believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may also cause harm to the environment if released to the atmosphere.

If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release

refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.

Electrical information

???The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., 15 Amp, AC only electrical outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three

prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Avoid connecting refrigerator

to a Ground Fault Interrupter (GFI) circuit. Do not use an extension cord or adapter plug.

???If the power cord is damaged, it should be replaced by an authorized service technician to prevent any risk.

???Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.

???Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.

???Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.

???Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.

IMPORTANT

Pressing and holding the On/Off button for three seconds, located on the left side of the temperature control panel will disable your refrigerator???s cooling system, but does not disconnect the power to the light bulb and other electrical components. To turn off power to your refrigerator you must unplug the power cord from the electrical outlet.

Grounding type wall receptacle

Do not, under

any circumstances, cut, remove,

or bypass the grounding prong.

Power cord with 3-prong grounded plug

CAUTION

To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.

This Use & Care Guide provides general installation and operating instructions for your model. We recommend using a service or kitchen contracting professional to install your refrigerator. Use the refrigerator only as instructed in this Use & Care Guide. Before starting the refrigerator, follow these important first steps.

Installation

???Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:

Location

???Choose a place that is near a grounded, non-GFCI, electrical outlet. Do Not use an extension cord or an adapter plug.

???If possible, place the refrigerator out of direct sunlight and away from the range, dishwasher, or other heat sources.

???The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.

???Consider water supply availability for models equipped with an automatic ice maker.

CAUTION

Do Not install the refrigerator where the temperature will drop below 55??F (13??C) or rise above 110??F (43??C). The compressor will not be able to maintain proper temperatures inside the refrigerator.

Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator.

???NOTE

If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.

Door opening

Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of refrigerator drawers and freezer baskets, the refrigerator should be in a position where both can be fully opened.

INSTALLATION

Leveling Freezer Drawer (if necessary)

1Check gasket seal around top, bottom, and sides of freezer drawer.

2If gasket is not sealed, open drawer and slightly loosen four drawer screws (two on each side) to allow drawer to rotate.

3Close drawer and recheck the seal on the gasket

(A). Open the drawer grabbing by the sides in the center (B). Be careful not to rotate the drawer.

4 Tighten four drawer screws.

5 Recheck gasket seal.

A B

Level Refrigerator & Adjust Doors

(if necessary)

Guidelines for final positioning of your refrigerator:

???All four corners of the cabinet must rest firmly on the floor.

???The sides should tilt ?? inch (6 mm) from front to back (to ensure that doors close and seal properly).

???Doors should align with each other and be level.

Most of these conditions can be met by raising or lowering the adjustable front rollers.

To level the cabinet using the front rollers (select models):

1Slightly open freezer drawer. Lift the toe grille and gently pull forward (see illustration).

2You can raise or lower each door. Use a ??? inch socket wrench to turn the adjustment screws (one per side).

Toe Grille Must

Fit in Slot on

Anti-tip Bracket

Screw/Washer

Assembly

(3) Retaining Clips

To raise: turn adjustment screw clockwise.

To lower: turn adjustment screw counterclockwise.

3Ensure both doors are bind-free with their seals touching the cabinet on all four sides and that cabinet is stable.

4After unit is leveled, lower anti-tip leg until it contacts the floor.

5 Install the toe grille by fitting into place.

To adjust the door stop:

Door stop is adjustable between 85 to 145 degrees.

???NOTE

View shown is looking up at the bottom of the refrigerator door.

Max

Open

Adjustable Door Stop

1 Open door to provide access to screw.

2 Loosen screw.

3 Adjust door to desired location.

Rotate

Door to Desired

Location

Adjusting Door

4Rotate door stop until it makes contact with the lower hinge.

INSTALLATION

5 Retighten screw.

Rotate

Door

Stop

Re-tighten

Screw

Retighten Screw

6Ensure door stops in desired location before resuming normal use.

To level the doors using the adjustable lower hinge (select models):

1Remove all food items from door bins on door being adjusted.

2 Open doors to 90 degrees.

3 Loosen or remove screw.

A Open

Door

90

Degrees

Bottom of Door

Loosen/Remove Screw (where applicable)

???NOTE

Adjustable hinge should only be used after doors have been leveled with rollers.

INSTALLATION

4Lift the door while adjusting the washer. To raise the door, rotate washer clockwise (when viewed from the bottom). To lower door, rotate washer counterclockwise (when viewed from the bottom).

Lower

Door

Raising/Lowering Door

To adjust the flipper mullion:

1 Loosen the screw located on the flipper mullion hinge.

Flipper

Mullion

Screw

Flipper

Mullion

Hinge

Adjusting Flipper Mullion Screw

2Adjust flipper mullion height. For proper connection with the flipper mullion guide, there should be a separation about the thickness of a coin (0.060 inches, or 1.5 mm) between the guide and flipper mullion.

Mullion

Guide

Flipper

Mullion

Thickness

of a Coin

Adjusting Flipper Mullion Height

3 Retighten screw.

Getting through narrow spaces

If your refrigerator will not fit through an entrance area, you can remove the doors. Check first by measuring the entrance.

To prepare for removing the doors:

1Make sure the electrical power cord is unplugged from the wall outlet.

2Open the freezer drawer and remove the toe grille (see ???Installation??? section).

3Remove any food from the door shelves and close the doors.

To remove the top hinge covers:

1Remove the two screws from each cover over the top door hinges.

2 Lift inside edge of hinge cover and tilt back.

Leave

Hinge

With

Door

To remove the refrigerator doors:

1Trace lightly around the door???s top hinges with a pencil. This makes reinstallation easier.

2Disconnect the harness by grasping both sides of the connector firmly, depress the latch, and pull apart. Remove the two screws from the top hinge. Lift the door off of the bottom hinge and set it aside.

???NOTE

You will be pulling approximately three feet of water tube from the back of the refrigerator.

4Unscrew the three lower hinge screws and hinge if necessary.

To reinstall the right door, reverse the above steps.

Lower Hinge Removal

Installing Freezer Drawer

1With lower slides pulled out, hang drawer onto slide brackets ensuring pins on each side are fully inserted into slots on each side.

2Reinstall four drawer screws (two per side), tighten down, and close drawer (C).

Once both doors are in place, ensure they are aligned with each other and level (Please see the ???Installation??? section for more details), and replace the top hinge cover.

CAUTION

Be sure doors are set aside in a secure position where they cannot fall and cause personal injury, or damage to the doors or handles.

Removing Freezer Drawer

1 Open freezer drawer.

2Remove drawer screws on right and left sides (two screws on each side).

CAUTION

Drawer is heavy. Use caution when lifting.

3 Lift drawer up and out to remove.

Install Screws

(2) Each Side

3Check gasket seal around top, bottom, and sides of freezer drawer.

4If gasket is not sealed, open drawer and slightly loosen four drawer screws (two on each side) to allow drawer to rotate.

5Close drawer and recheck the seal on the gasket

(A). Open the drawer grabbing by the sides in the center (B). Be careful not to rotate the drawer.

A B

6 Tighten four drawer screws.

7Recheck gasket seal.

8Install the toe grille by fitting into place.

WARNING

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before

connecting a water supply line to the refrigerator.

CAUTION

To Avoid Property Damage:

???Copper or Stainless Steel braided tubing is recommended for the water supply line. Water supply tubing made of ?? inch plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line.

???DO NOT install water supply tubing in areas where temperatures fall below freezing.

???Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT

Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need:

To Connect Water Supply Line To Ice Maker Inlet Valve

1.Disconnect refrigerator from electric power source.

2.Place end of water supply line into sink or bucket.

Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.

3.Remove plastic cap from water valve inlet and discard cap.

4.If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (?? inch/6 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT overtighten. See Figure 1.

If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT overtighten. See Figure 2.

5.With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.

6.Coil excess water supply line (copper tubing only), about 2?? turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

7.Turn ON water supply at shutoff valve and tighten any connections that leak.

8.Reconnect refrigerator to electrical power source.

Copper water line from household water supply

(Include enough tubing in loop to allow moving refrigerator out for cleaning.)

Stainless Steel water Line

Water Valve

Bracket

Valve Inlet

Water Valve

6 ft. Stainless Steel water line from household water supply

Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/state building codes, Frigidaire recommends for homes with existing valves its Smart Choice?? water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice?? water line kit 5305510264 (with a 20 ft. Copper Water Line with self-tapping saddle valve). Please refer to www.frigidaire.com/store for more information.

Ice maker operation & care

After the refrigerator is installed properly, the ice maker can produce ice within 24 hours. It can completely fill an ice bin in about three days.

When using the ice maker for the first time and in order for the ice maker to work properly, it is necessary to clear air from water filter tubing. Once ice maker begins making ice, allow the bucket to fill completely, then discard the first TWO FULL buckets of ice. It will take at least two days to completely fill the bucket on regular ice making mode or 1?? days on fast ice mode.

The ice maker produces approximately four pounds of ice every 24 hours depending on usage conditions.

IMPORTANT

Your ice maker is turned on at the factory so it can work as soon as you install your refrigerator. If you cannot connect a water supply, lift the ice maker???s wire signal arm to turn it off. Otherwise, the ice maker???s

fill valve may make a loud chattering noise when it attempts to operate without water.

Turning the ice maker on and off

Ice production is controlled by lifting/lowering the ice maker???s wire signal arm. To gain access to the ice maker, pull the freezer drawer out. Lift the wire signal arm to turn the ice maker OFF and lower the wire signal arm to turn it ON.

Wire

Signal Arm

Ice maker tips

???If your refrigerator is not connected to a water supply or the water supply is turned off, turn off the ice maker by lifting wire signal arm.

???The following sounds are normal when the ice maker is operating:

-Motor running

-Ice dropping into ice bin

-Water valve opening or closing

-Running water

???Ice cubes stored too long may develop an odd flavor.

Empty the ice bin as explained below.

Quick Ice Function

Your refrigerator is equipped with a Quick Ice Function, that increases ice production. This function terminates automatically.

Cleaning the ice maker

CAUTION

If the water supply to your refrigerator is softened, be sure the softener is properly maintained. Chemicals from a water softener can damage the ice maker.

Clean the ice maker and ice bin at regular intervals, especially prior to vacation or moving.

1 Turn off the ice maker.

2 Remove the ice bin.

3Empty and carefully clean the ice bin with mild detergent. Do not use harsh or abrasive cleaners. Rinse with clean water.

4Allow the ice bin to dry completely before replacing in the freezer.

5 Replace the ice bin. Turn the ice maker on. Remove and empty the ice bin if:

???An extended power failure (one hour or longer) causes ice cubes in the ice bin to melt and freeze together.

Remove the ice bin and shake to loosen the cubes or clean as explained above.

CAUTION

NEVER use an ice pick or similar sharp instrument to break up the ice. This could damage the ice bin and dispenser mechanism.

To loosen stuck ice, use warm water. Before replacing the ice bin, make sure it is completely dry.

CAUTION

To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change. Allow the glass shelves to stabilize to room temperature before cleaning. Do not wash

in dishwasher.

???NOTE

Features may vary according to model.

Your refrigerator includes SpillSafeTM glass shelves that are designed to catch and hold accidental spills.

You can easily adjust shelf positions in the fresh food compartments to suit your needs. The shelves have mounting brackets that attach to slotted supports at the rear of each compartment.

To change the position of a shelf:

1Remove all food from the shelf.

2Lift the front edge up and pull the shelf out.

3Replace by inserting the mounting bracket hooks into the desired support slots.

4Lower the shelf and lock into position.

Shelf features

SpillSafeTM Shelf

STORAGE FEATURES

Slide-Under Shelf

Drawers

Your refrigerator includes a variety of storage drawers.

These drawers are located in fixed positions at the bottom of the fresh food compartment.

Crispers

Crisper drawers are designed for storing fruits, vegetables, and other fresh produce.

Opening Crisper Drawer

STORAGE FEATURES

Crisper humidity control

Crisper drawers include a sliding control for adjusting the humidity inside the crisper. Leafy vegetables keep best when stored with the Humidity Control set on Higher Humidity. Fresh fruits keep best when stored with the Humidity Control set on Lower Humidity.

Humidity Control

Higher Lower

Humidity Humidity

Adjusting Crisper Humidity

To remove the Crisper Drawer for cleaning: 1 Pull the drawer out until it stops.

2 Lift the front slightly and remove the drawer.

Removing Crisper Drawer

Deli drawer

Ideal for storage of deli meats and cheese.

Doors

Storage bins

The doors to your fresh food compartment use a system of modular storage bins. All of these bins are removable for easy cleaning. Some of them have fixed positions, while others can be adjusted to your needs.

Door bins are ideal for storing jars, bottles, cans, and large drink containers. They also enable quick selection of frequently used items.

To change the position of an adjustable door bin: 1 Remove all food from the door bin.

2Grip the bin firmly with both hands and lift it upward.

3Remove the bin.

4Place the bin just above desired position.

5 Lower the bin onto supports until locked in place.

Adjustable Door Bin

6 Place bin liner into bin.

Accessories (varies by model) Dairy compartment

Use the dairy compartment, at the top of the fresh food compartment door, for short- term storage of cheese, spreads, or butter. The dairy compartment is designed to be warmer than the open area and includes a lift-up cover and a dairy divider

(select models).Dairy Compartment

Freezer Features (varies by model)

Stabilizer Bar

Basket

Retainer

Clips

Two Freezer Baskets

To Remove Upper Basket

1 Remove all items from basket.

2Remove basket by pulling baskets out to their full extension and lift out.

Removing Upper Basket

To reinstall upper basket, position basket onto the retainer clips making sure the front of the basket rests in the retainer clips on the stabilizer bar.

???NOTE

If basket is not resting on stabilizer bar retainer clips, the drawer will not close properly.

STORAGE FEATURES

To Remove Lower Basket

Basket

Retainer

Removing Lower Basket

1 Remove all items from basket.

2Remove the basket by tilting it forward and lifting it from the retainer clips.

To reinstall lower basket, insert basket into retainer clips.

Dividers Removal

Lift up on the front of the middle divider and pull out.

Middle Basket

Divider

Retainers

Stabilizer

Bar

Middle Basket Divider

Lift up on the rear of the lower divider and pull out.

Lower Basket

Divider

Lower Basket Divider & Spill Guard Tray

???NOTE

Spill Guard Tray should be hand washed in warm water.

Ideas for storing foods

Fresh food storage

???Keep the fresh food compartment between 34?? F and 40?? F with an optimum temperature of 37?? F.

???Avoid overcrowding the refrigerator shelves, which reduces air circulation and causes uneven cooling.

Fruits and vegetables

???Store fruits and vegetables in crisper drawers, where trapped moisture helps preserve food quality for longer time periods.

???Wash items and remove excess water.

???Wrap any items that have strong odors or high moisture content.

Meat

???Wrap raw meat and poultry separately and securely to prevent leaks and contamination of other foods or surfaces.

???Use the deli drawer to store meat/poultry for short- term storage. Any meat to be kept longer than two days should be frozen.

Frozen food storage

???Keep the freezer compartment at 0?? F or lower.

???A freezer operates most efficiently when it is at least

??? full.

Packaging foods for freezing

???To minimize food dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags, or airtight containers. Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out, change color, and develop an off-flavor (freezer burn).

???Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.

???Do not refreeze meat that has completely thawed.

Loading the freezer

???Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.

???Leave a space between packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.

Ideas for saving energy

Installation

???Locate the refrigerator in the coolest part of the room, out of direct sunlight, and away from heating ducts or registers.

???Do not place the refrigerator next to heat-producing appliances such as a range, oven, or dishwasher.

If this is not possible, a section of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more efficiently.

???Level the refrigerator so that the doors close tightly.

Temperature settings

???Refer to the ???Controls??? section for procedures on temperature settings.

Food storage

???Avoid overcrowding the refrigerator or blocking cold air vents. Doing so causes the refrigerator to run longer and use more energy.

???Cover foods and wipe containers dry before placing them in the refrigerator. This cuts down on moisture build-up inside the unit.

???Organize the refrigerator to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.

???Do not place a hot container directly on a cold shelf. Remember, such an extreme temperature change may damage the glass.

Understanding the sounds you may hear

Your new, high-efficiency refrigerator may introduce unfamiliar sounds. These sounds normally indicate your refrigerator is operating correctly. Some surfaces on floors, walls, and kitchen cabinets may make these sounds more noticeable.

The following is a list of major components in your refrigerator and the sounds they can cause:

AEvaporator Refrigerant through the evaporator may create a boiling or gurgling sound.

BEvaporator fan You may hear air being forced through the refrigerator by the evaporator fan.

CDefrost heater During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.

DAutomatic ice maker When ice has been produced, you will hear ice cubes falling into the ice bin. Ice maker fan, water valve activation, and refrigerant gas fluid may create sounds from

its operation.

EElectronic control & automatic defrost control These parts can produce a snapping or clicking sound when turning the cooling system on and off.

FCondenser fan You may hear air being forced through the condenser.

GCompressor Modern, high-efficiency compressors run much faster than older models. The compressor may have a high-pitched hum or pulsating sound.

HWater valve Makes a buzzing sound each time it opens to fill the ice maker.

IDrain pan (not removable) You may hear water dripping into the drain pan during the defrost cycle.

JCondenser May create minimal sounds from forced air.

MMotorized damper May produce a light humming during operation.

???NOTE

Energy efficient foam in your refrigerator is not a sound insulator.

???NOTE

During automatic defrost cycle, a red glow in the back wall vents of your freezer compartment is normal.

CHANGING THE FILTER

Locating the Filters

Your refrigerator is equipped with water filtering system. The water filter system filters all dispensed drinking water, as well as the water used to produce ice.

Water Filter

The water filter is located at the top right side of the fresh food compartment.

Replacing the Water Filter

In general, you should change the water filter every six months to ensure the highest possible water quality. The Water Filter Status light on the user interface prompts you to replace the filter after a standard amount of water

(200 gallons/757 liters for PureSource UltraTM) has flowed through the system. The water filter status light on this model is not performance tested or certified

by NSF.

If your refrigerator has not been used for a period of time

(during moving for example), change the filter before reinstalling the refrigerator.

Filter Cartridge

Ordering Replacement Filters

To order your replacement filters, please visit our online store at www.frigidaire.com/store, by calling toll-free at 877-808-4195, or by visiting the dealer where you purchased your refrigerator. Frigidaire recommends that you order extra filters when you first install your

refrigerator, and that you replace your filters at least once every six months.

Here is the product number to request when ordering:

PureSource UltraTM Water Filter

Part #ULTRAWF

More about your Advanced Water Filter

The PureSource UltraTM ice and water filter system is tested and certified to NSF/ANSI

Standards 42 and 53 for the reduction of claims specified on the performance data sheet.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Test & certification results:

???Rated Capacity - 200 gallons/757 liters for

PureSource UltraTM ice and water filter

???Rated service flow - .50 gallons per minute

???Operating Temp.: Min. 33??F, Max. 100??F

???Maximum Rated Pressure - 100 pounds per square inch

???Recommended Minimum Operating Pressure: 30 pounds per square inch

To replace your PureSource UltraTM water filter:

It is not necessary to turn the water supply off to change the filter. Be ready to wipe up any small amounts of water released during the filter replacement.

1 Turn Off the ice maker by raising the wire signal arm.

2Remove the filter by pushing on the end/face of the filter.

3Slide the old water filter cartridge straight out of the housing and discard it.

4Unpackage the new filter cartridge. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing.

5Push firmly until the cartridge snaps into place (you should hear a click as the cartridge engages the snap-in connector).

6 Turn On the ice maker by lowering the wire signal arm.

7Press and hold the Water Filter button on the Ice & Water Dispenser control panel for three seconds. When the display changes from Red to Green, the status has been reset.

8After replacing the water filter and in order for the ice maker to work properly, it is necessary to clear air from water filter tubing. Once ice maker begins making ice, allow the bucket to fill completely, then discard the first TWO FULL buckets of ice. It will take at least two days to completely fill the bucket on regular ice making mode or 1?? days on fast ice mode.

CARE & CLEANING

Replacing LED Lights (select models)

The fresh food compartments of your refrigerator may have LED lights. Always use Frigidaire parts for replacement.

To replace LED Lights:

1 Unplug your refrigerator???s power cord.

2 Remove lens cover.

3Remove LED board.

4Replace LED board and snap in place assuring the light is facing in toward the unit (inside fresh food).

5 Replace lens cover.

Ordering Replacement LED Lights

Order new LEDs by calling 877-808-4195, online at www.frigidaire.com/store, or through the dealer where you bought the refrigerator. Here is the product number to request when ordering:

LED Light, Part #242196201

WATER/MOISTURE/FROST INSIDE REFRIGERATOR

???Call your Frigidaire service representative, who can interpret any messages or number codes flashing on the digital displays.

???This is normal in humid weather. Press Energy Saver icon to reduce exterior moisture on the cabinet between the doors. When humidity is lower, the moisture should disappear and the Energy Saver icon can be pressed again to turn it off.

???See CONCERN column OPENING/CLOSING OF

DOORS/DRAWERS.