Fisher_amp_Paykel_Oven

QUICK START GUIDE

Built-in oven

NZ AU GB IE

SETTING THE CLOCK

You set the clock within the user preference menu. To learn more about the user preference menu, refer to your User guide.

Note: If you do not wish to set the time initially when the oven is first switched on at the wall, press the cancel button to exit the clock setting. If you want to set the clock later, follow the steps under ???To change the time???.

Keep this document handy for easy reference.

For detailed information on the other features of your oven, see your ???User guide???.

Before using your oven, make sure you read the full ???User guide???, with special attention to the ???Safety and warnings??? section.

For contact information or if you require service, assistance or replacement parts, see the end of this document or your ???Service & warranty??? booklet.

YOUR OVEN

When the oven is first switched on at the wall

To change the time

(within the user preference menu)

1Press and hold the left and right scroll

buttons together for 3 seconds to enter the user preference menu.

The display will either show 12 Hror 24 Hr

2Press the select button to confirm. The display will flash.

3Follow steps 2-5 left to set the time.

At step 2a, you also now have the ability to scroll between 24 Hr,

12 Hr and OFF (turns the display off). Refer to the User guide to learn more about this feature.

THE CONTROL PANEL

Before using your oven for the first time, you should fit both the Catalytic Panels (supplied). See ???Care and cleaning??? in your user guide for details about these self cleaning panels.

You do this by:

2 REMOVE ALL SHELVES FROM THE OVEN

3 REMOVE BOTH SIDE RACKS

Locking the control panel

To lock, press and hold the select button for 2 seconds.

To unlock, press and hold the cancel button for 2 seconds.

Timer indicator (see ???Using the timer???)

1Remove all the shelving, taking special care with the telescopic sliding shelves.

2To remove a telescopic sliding shelf, grip it at the front (making sure you are gripping the wire shelf and the sliding frame together), lift upwards and pull it out of the oven.

For your safety, the wire shelf and telescopic sliding frame are built together as one unit and are not separable.

Remove both side racks by 1) pushing down on the retaining wire until it clears the lower lock stud and swing out wards to 2) clear the upper lock studs, then 3) lift out.

lock stud

retaining wire

2 2

Automatic stop time is set

continued over

FIRST USE

4 FIT BOTH CATALYTIC PANELS

Place each catalytic panel flush against the side wall, noting the position of the cutouts for the lamp and lock nuts

Catalytic panel

5 REPLACE BOTH SIDE RACKS

To replace the side racks, locate the top of the side rack into the two upper lock studs and gently push the retaining wire back under the lower lock stud.

1 1

lock stud

retaining wire

7 CONDITION THE OVEN

There will be a distinctive smell and a small amount of smoke during the conditioning process as manufacturing residue is burnt off. This is normal, but make sure the kitchen is well ventilated during the conditioning.

Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.

USING THE TIMER

6 REPLACE SHELVING

To replace a wire shelf, check the guard rail (as shown) to make sure the shelf is the right way up. slide it horizontally back along the side racks ensuring it is level and the stop notch is facing down.

To replace a telescopic sliding shelf, position it so that the front bar is toward you, as shown. Check that the sliding frame is not extended.

Check the guard rail (as shown) to make sure the shelf is the right way up.

Position the shelf so that it is level and the rear shelf tag at the back of the sliding frame rests behind the side rack wire (as shown). Then push the sliding shelf all the way to the back of the oven, until the front shelf tag drops into place behind the side rack wire.

For your safety, the wire shelves and telescopic sliding frames are built together as one unit and are not separable. This means that when placed properly on the side racks, the slides will prevent the wire shelves from tilting when pulled towards you.

To prevent the tags from lifting off the side racks, take care to slide the shelves forward horizontally.

Guard rail

You can use the timer at any time, even if you are not using the oven.

If the time is more than an hour, the display will count down in minutes (hr:min). If it is less than an hour, it will count down in seconds (min:sec). You can set the timer for up to 23 hours 59 minutes.

Important!

The timer does NOT turn the oven off.

Guard rail

1Select the timerby pressing

the right scroll button once. The timerindicator will appear and the colon will flash.

To modify the timer setting

button once.

Press the right scroll button to scroll back to the timer.

7 CONDITION THE OVEN

It is important to condition your oven before using it for cooking and baking. Conditioning will burn off any manufacturing residues and ensure that you get the best results right from the start.

1 Make sure you have removed ALL the cable ties used to secure the shelving during transit. 2 Make sure you have set the clock.

3Make sure all the shelves are fitted.

1 Make sure the display shows the remaining time counting down.

2Press the select button.