DD36 and DD90 models
US CA NZ AU GB IE
DD36 and DD90 models
US CA NZ AU GB IE
Important!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed on the back cover or contact your local Fisher & Paykel dealer.
2 Safety and warnings
Your DishDrawer?? has been carefully designed to operate safely during normal dishwashing procedures. Please keep the following instructions in mind when you are using your DishDrawer??.
Important safety instructions
WARNING! - When using your dishwasher, follow basic precautions, including the following: Read all instructions before using the DishDrawer??.
The information in this manual must be followed to minimise the risk of fire or explosion or to prevent property damage, personal injury or loss of life.
Use the DishDrawer?? only for its intended function as described in this user guide. This appliance is intended to be used in household and similar applications such as:
???staff kitchen areas in shops, offices and other working environments;
???farm houses;
???by clients in hotels, motels and other residential type environments;
???bed and breakfast type environments.
Use only detergents or rinse aid recommended for use in a domestic dishwasher and keep them out of reach of children. Check that the detergent dispenser is empty after the completion of each wash programme.
When loading items to be washed, locate sharp items so that they are not likely to damage the lid seal and load sharp knives with the handle up to reduce the risk of
Do not touch the heater plate during or immediately after use.
Do not operate your DishDrawer?? unless all enclosure panels are properly in place. Do not tamper with the controls.
Do not abuse, sit on, stand in or on the drawer or dish rack of the DishDrawer??.
The DishDrawer should not be left in the open position since this could present a tripping hazard.
The adjustable racks are designed to support cups, glasses and kitchen utensils. When the adjustable racks are in the DishDrawer?? do not lean on or use them to support your body weight.
To reduce the risk of injury, do not allow children to play in or on the DishDrawer??.
Under certain conditions, hydrogen gas may be produced in a hot water heater system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the dishwasher, turn on all hot water taps and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.
Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children away from the dishwasher when the door is open. Check that the detergent receptacle is empty after completion of the wash cycle.
Safety and warnings 3
Important safety instructions
Installation
This DishDrawer?? must be installed and located in accordance with the Installation instructions before it is used. If you did not receive Installation instruction sheets with your DishDrawer??, you can order them by calling your Authorised Repairer or download them from our local Fisher & Paykel website, listed on the back cover.
Installation and service must be performed by a qualified technician.
If the power supply cord is damaged, it must be replaced by a dealer or Authorised Repairer or a similar qualified trades person in order to avoid a hazard.
Ensure the DishDrawer?? is secured to adjacent cabinetry using the brackets provided. Failure to do so may result in an unstable product, which may cause damage or injury.
Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or has missing or broken parts, including a damaged power supply cord or plug.
Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the DishDrawer??.
Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload. Make sure that the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
Do not install or store the DishDrawer?? where it will be exposed to temperatures below freezing or exposed to weather.
Do not use an extension cord or a portable electrical outlet device (e.g.
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an
in accordance with all local codes and ordinances. WARNING - Improper connection of the
If the DishDrawer?? is installed as a permanently connected appliance:
GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded metal, permanent wiring system, or an
4 Safety and warnings
Important safety instructions
Maintenance
Disconnect the appliance from the power supply before any cleaning or maintenance.
Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in this user guide. We recommend that you call an Authorised Repairer.
Keep the floor around your appliance clean and dry to reduce the possibility of slipping. Keep the area around/underneath your appliance free from the accumulation of combustible materials, such as lint, paper, rags and chemicals.
Important!
Under no circumstances should you open the drawer whilst the DishDrawer?? is in operation.
Operational
Always press the 
button to pause and wait until you hear the three additional beeps before opening the drawer.
The DishDrawer?? must be used with the motor assembly, filter plate, drain filter and spray arms in place.
When disconnecting the appliance pull the plug rather than the power supply cord or junction of cord to avoid damage.
Take care when loading the DishDrawer?? not to load dishware items so they prevent the lid from properly sealing with the drawer. Items should be placed so they do not protrude above and/or forced into the drawer, otherwise a service call may result.
Household appliances are not intended to be played with by children. Children or persons with a disability which limits their ability to use the appliance, should have a responsible person instruct them in its use. The instructor should be satisfied that they can then use the appliance without danger to themselves or their surroundings.
Close supervision is necessary if this appliance is used by or near children. Do not allow children to play inside, on or with this appliance or any discarded appliance.
If a dishwasher cleaner is used, we would strongly recommend a wash programme with detergent should be run immediately afterward, to prevent any damage to the DishDrawer??.
The DishDrawer?? is designed for washing normal household utensils. Items that are contaminated by petrol, paint, steel or iron debris, corrosive, acidic or alkaline chemicals are not to be washed in the DishDrawer??.
If the DishDrawer?? is not being used for long periods of time, turn the electricity and water supply to the DishDrawer?? off.
Do not operate your appliance by means of an external timer or separate
This appliance must be earthed.
Fuse replacement
The mains lead of this appliance is fitted with a BS 1363A 13 A fused plug. To change a fuse in this type of plug, use an ASTA approved fuse to BS 1362 type and proceed as follows:
1 Remove the fuse cover and fuse.
2 Fit the replacement 13A fuse into the fuse cover. 3 Refit both into plug.
Important!
The fuse cover must be refitted when changing a fuse and if the fuse cover is lost, the plug must not be used until a correct replacement is fitted.
Correct replacements are identified by the colour insert or the colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical store.
For the Republic of Ireland
The information given in respect to Great Britain will frequently apply, but a third type of plug and socket is also used: the
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact an Authorised Service Agent. Please do not attempt to change the plug yourself. This procedure must be carried out by a qualified service technician in compliance with the manufacturer???s instructions and current standard safety regulations.
6 Operating instructions - Controls
Power button
/ 
The
/ 
button turns the DishDrawer?? on or off. Opening the drawer will automatically turn the DishDrawer?? on for 30 seconds. To end a wash programme in mid cycle, press the
/ 
button. Any water in the DishDrawer?? will be pumped out.
Start/Pause button 
The 
button starts a wash programme. Press the 
button to pause or restart the DishDrawer?? during a wash programme. When paused, wait for three beeps before opening the drawer. Forcing the drawer open while in mid cycle may cause damage or injury.
Delay start
The 
button also sets the Delay start feature which can delay the start of a wash programme from 1 to 12 hours.
To activate Delay start
1Press and hold the 
button until the light above the 
button turns orange or purple, depending on your model.
2Continue holding the 
button down until the desired delay time has been reached. The DishDrawer?? will emit audible ???beeps??? as you hold the 
button down, each beep indicates
another hour delay.
3The DishDrawer?? will start once the delay time has elapsed and the drawer is closed.
To cancel Delay start
Press the
/ 
button.
Lock button 
/
(optional)
Operating instructions - Controls 7
Keylock
The Keylock feature disables all the buttons on the DishDrawer??.
To activate, press and hold the 
/
button until you hear one beep (3 seconds). The light above the 
/
button is lit when Keylock is activated.
To cancel the Keylock feature, press and hold the 
/
button until the light above the 
/
button disappears.
Childlock
The Childlock feature locks the drawer and disables all the buttons.
To activate, press and hold the 
/
button until you hear two beeps (5 seconds). The light above the 
/
button is lit when Childlock is activated.
To cancel the Childlock feature, press and hold the 
/
button until the light above the 
/
button disappears.
Wash programme selector
Press the 
button to select a wash programme. The DishDrawer?? will remember the last programme used.
Wash programme selector (GB IE only)
Press the 
button to select a wash programme. The DishDrawer?? will remember the last programme used.
Heavy Normal Fast Delicate Rinse
/
button (optional)
Press the ECO button if you would like the wash programme to use less energy. The red ECO light will indicate the feature is on. If your dishes are heavily soiled or you require enhanced dry performance, we do not recommend ECO programmes.
Power failure
If the DishDrawer?? is operating and a power failure occurs, it will stop. The DishDrawer?? may be unable to be opened during this time. When the power supply is resumed, the DishDrawer?? will restart in the same part of the wash programme.
8 Operating instructions - Quick start
2 Add detergent
3Check rinse aid
4 Press the
/ 
button
5Select a wash programme
7Check
Ensure there is nothing obstructing the spray arms. The drain filter must be level with the filter plate.
Note: to identify these parts, see illustrations in ???User maintenance instructions???.
9Finish
The DishDrawer?? will beep six times to indicate the end of the wash programme. At the end of the wash programme the drying fan will continue to run for a set time or until the drawer is opened. The fan assists with drying and uses negligible amounts
of energy. It is normal for some water to remain in the drain filter area after the wash programme is complete.
8
2
7
5
6
4
Caring for your dinnerware 9
The combination of high temperatures and dishwasher detergent may cause damage to some items if they are washed in the DishDrawer??. Remember, if in any doubt about any aspect concerning items washed in the DishDrawer??, follow the instructions from the manufacturer of the items, or wash the item by hand.
Cutlery & silverware
All cutlery and silverware should be rinsed immediately after use to prevent tarnishing caused by some foods. The Rinse wash programme is useful for this. Silver items should not come into contact with stainless steel, eg other cutlery. Mixing these items can cause staining. Remove silver cutlery from the DishDrawer?? and hand dry it immediately after the programme has finished.
Aluminium
Aluminium can be dulled by dishwasher detergent. The degree of change depends on the quality of the product.
Other metals
Iron and cast iron objects can rust and stain other items. Copper, pewter and brass tend to stain.
Woodware
Wooden items are generally sensitive to heat and water. Regular use in the dishwasher may cause deterioration over time. If in doubt, wash by hand.
Glassware
Most everyday glassware is dishwasher safe. Crystal, very fine and antique glassware may etch that is, become opaque. You may prefer to wash these items by hand.
Plastic
Some plastic may change shape or colour with hot water. Check manufacturer???s instructions about washing plastic items. Washable plastic items should be weighed down so they do not flip over and fill with water or fall through the base rack during the wash. Use the
Decorated items
Most modern china patterns are dishwasher safe. Antique items, those with a pattern painted over the glaze, gold rims or hand painted china may be more sensitive to machine washing. If in doubt, wash by hand.
Glued items
Certain adhesives are softened or dissolved in machine washing. If in doubt, wash by hand.
Holiday time
If the DishDrawer?? is not going to be used for some time, we recommend you leave the DishDrawer?? clean and empty. Leave the drawers ajar to allow air to circulate. Turn off both the power and water supply to the DishDrawer??.
10 Racking and accessories
Cutlery basket
To reduce the risk of injury, we recommend loading knives and sharp utensils with handles facing up.
Mix spoons, knives and forks within each section to stop cutlery nesting together and to ensure the water circulates freely.
Keep stainless steel from touching silver cutlery to avoid staining.
Removable small items container
Small, light items like baby bottle teats are best placed into the small items container to prevent them from being displaced during the wash.
Racking and accessories 11
Removable small items container
To optimise the cutlery space within the basket, the small items container can be placed elsewhere on the base rack. If laid flat, make sure the solid plastic side is facing up.
If you place a fully laden small items container under the adjustable racks, it is best to leave the rack space directly above the container empty: there may not be enough water reaching items that are placed there.
Removable tablet tray
If you are using dishwasher tablets, place them on the removable tablet tray, as shown. See also ???Using tablets??? for more information.
We do not recommend using tablets in USA and Canada models. The
12 Racking and accessories
Glass supports
These clip on the rack wires to give your tall glasses extra stability.
Stemware notches
These notches help support
This keeps flimsy
items (eg light 
plastic lids and 
bottles) or large 
platters and 
plates stable, 
so they cannot 
be dislodged 
during the wash. 
Slide the item 
between the 
prongs of the clip. 
Slide to the left or right to fit larger plates.
For optimum stability, place larger plates between the longer tines in the front.
Fold the tine sections down towards each other if you need the space for pots or other large items.
Racking and accessories 13
Adjustable racks
You can adjust these independently of each other to any height:
1Fold up to unlock the rack.
2Adjust the height to suit by sliding up or down.
3Fold down to lock in position.
Fold the racks away if you need the space.
Knife clip
(supplied with some models only)
This clips onto the
adjustable racks and
supports knives and
other utensils during
the wash.
Always ensure that
knife blades are facing down.
Cup rack with folding support wire
Fold the wire up to support tall glasses.
14 Loading suggestions
When loading your DishDrawer??, make sure that
you place items so that water coming from the rotating spray arms below can reach all areas (wash performance will be reduced if it can???t)
nothing blocks the water from getting to items on the adjustable racks.
How NOT to load your DishDrawer??
Overcrowded and wash water will not reach some of the dinnerware.
Cups, glasses and bowls must have their openings facing down.
Ensure dishware items are not forced into or protrude out of the drawer, as this may prevent the lid from properly sealing which could result in a service call. Locate sharp items safely to prevent injuring the user and damaging the lid assembly.
Check the bottom of the cutlery basket to ensure sharp or pointed items have not come through as they may stop spray arm rotation.
The plates are nesting together and wash water may not get through.
Ensure cutlery are not nesting or stuck together. They need to be evenly spread out.
Ensure cutlery has not fallen through the base rack and stopped the spray arms from rotating.
The large bowl is blocking wash water reaching the adjustable racks.
Large utensils should be on the adjustable racks so they do not become dislodged and stop the spray arms from rotating.
Sharp or pointed items must be placed horizontally or with sharp edges/points facing down to avoid risk of injury.
Using tablets 15
Important!
We do not recommend using dishwasher tablets in USA and Canada models. The
Using tablets could improve wash performance in hard water areas.
Tablets can either be placed in the cutlery basket or alternatively, placed directly in the wash compartment as below. If you are using dishwasher tablets with a
Preferred:
Place the tablet on the removable tablet tray.
Alternative:
If the cutlery basket cannot be used, place tablet in the bottom of the DishDrawer.
16 Water hardness and dishwashing
What is water hardness?
Hard water is water with a high concentration of minerals such as calcium and magnesium. In soft water, this concentration is low. Water hardness varies by geographical location.
How does water hardness affect dishwashing?
Hard water can be detrimental to the peformance of your DishDrawer. Over time, glassware washed in hard water will become opaque and dishes will become spotted or covered in a white film. Using very hard water can cause DishDrawer parts to fail over time.
Naturally soft or softened water has no detrimental effects if used with the correct amount of detergent. However, excess detergent combined with hot, soft water may cause irreversible etching on glassware. Etching first appears as a
What can I do to minimise any detrimental effects?
Contact your local water company to find out about water hardness in your area.
If your home has hard water and your DishDrawer has no
Follow the detergent quantity recommendations on the following page.
Use a detergent with high phosphate content. Phosphate softens the water and this improves wash results.
Use rinse aid. We recommend you turn the rinse aid setting to 5 to help improve wash performance.
Use a dishwasher cleaner/descaler regularly, or whenever you notice a
Important!
We recommend fitting a water softener to the household water supply. If the water hardness in your home is above 250 ppm/14.6 gpg, a water softener has to be fitted to maintain the performance of your DishDrawer.
If your home has naturally soft or softened water???
Avoid using too much detergent. Follow the quantity recommendations on the following page. Ensure the DishDrawer is not overloaded and water can reach all the dishes.
Wash programmes and detergent quantities 17
Wash programmes
All programmes except Rinse can be used in ECO mode to save energy. If your dishes are heavily soiled or you require enhanced dry performance, we do not recommend ECO programmes. See section ???Operating instructions ??? Controls??? for wash programme selection.
Detergent quantities
Find out about water hardness in your home, then use the table below to determine how much detergent to use for each wash programme. See also section ???Water hardness and dishwashing???. The detergent dispenser has markings to help you measure the correct quantities. See following section ???Detergent dispenser???.
* If you have a household water softener installed or your DishDrawer has a
under 100 ppm/6 gpg, irrespective of the water hardness in the area. See also section ???Water softener???.
18 Detergent dispenser
Important!
Only use powdered detergent recommended for domestic automatic dishwashers in the detergent dispenser.
Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children and infirm persons away from the DishDrawer when it is open. Check that the detergent dispenser is empty after completion of the wash programme.
Do not place dishwasher tablets in the detergent dispenser.
Detergent and dishwasher tablets should not be in direct contact with dishes or cutlery. Liquid detergents are not suitable to be used in the DishDrawer??.
Hand washing liquids, soap, laundry detergents or disinfectants will damage the DishDrawer??.
Filling the detergent dispenser
1Press the latch down and the dispenser will open.
2Pour detergent into the appropriate compartment(s). Use the markings to help you measure the correct quantities. No detergent is needed for the Rinse programme.
3Close the dispenser until it clicks shut. The detergent will automatically be released into the DishDrawer?? during the wash programme.
Amount of detergent to use
Refer to previous section ???Wash programmes and detergent quantities???, and follow the quantities relevant to your location and water hardness level.
(used in USA and Canada only)
2 teaspoons (full)
1 teaspoon 
Latch
6 teaspoons (full) 
4 teaspoons
2 teaspoons
Main wash compartment
Rinse aid dispenser 19
We highly recommend the regular use of liquid rinse aid to give the best drying results.
Rinse aid gives a
Filling the rinse aid dispenser
1 Turn the plug anticlockwise and remove.
2Pour the rinse aid into the circular opening.
3 Take care not to spill rinse aid into the DishDrawer??.
Important!
Any spillages must be wiped up to prevent excess foaming. Failure to wipe rinse aid spillages may result in a service call which will not be covered by warranty.
4Fit the plug back into the original position.
How much rinse aid to use
The regulator may need adjusting to suit your water conditions or the particular dishwasher tablet you are using. The lowest setting is ???1??? and the highest is ???5???. Refer to the ???Option adjustments??? section to adjust the rinse aid setting.
If there is excessive foam at the end of the wash or you are using dishwasher tablets with
If dishes are wet or streaky after drying, increase the setting.
If you live in a hard water area and you have no water softener installed in your water supply or built into your DishDrawer, we recommend adjusting the rinse aid setting to 5.
Rinse aid indicator light
If the rinse aid indicator light is red, refill the dispenser. If the rinse aid indicator light is dimly lit or not lit at all, there is enough rinse aid for the wash.
Note:
Lighter coloured rinse aids will not dim the indicator light as effectively as darker coloured rinse aids. When the rinse aid is being dispensed, you may notice some unusual noises during the wash:
this is normal.
Indicator light Plug
20 Water softener
Setting up the water softener
Important!
Only GB IE models have a
Models with water softener are not currently available in New Zealand, Australia, USA or Canada.
Determine the water hardness in your local area
Your local water company will be able to provide you with information. Identify the setting you require for your DishDrawer?? from the water hardness table below. For example, if your water hardness is 500ppm, then the water softener setting on your DishDrawer?? should be 4. Refer to the ???Option adjustments??? section to adjust the water softener so that the setting corresponds to your water hardness.
Notes:
If your water hardness is above 625ppm, we highly recommend you completely fill the appropriate compartment(s) of the detergent dispenser for all programmes except Rinse and the rinse aid setting should be at 5. If your water hardness is above 625ppm, the wash performance of your DishDrawer?? will decline.
You may hear some unusual noises when the water softener is in operation, this is normal.
Salt reservoir
Salt container
How to fill the salt reservoir
1Open the DishDrawer??.
2Unscrew the salt reservoir cap by turning anticlockwise.
3Place the salt into the salt container and pour the contents into the salt reservoir. The salt reservoir can hold up to approximately 1 lb/0.5 kg of salt.
4Fit the cap tightly back into its original position.
5If you do not wash your dishes immediately after filling the salt reservoir, run a Rinse programme to remove any salt water or spilt granules.
Note:
When filling the salt reservoir, you may notice water being displaced from the water softener overflow.
Water softener 21
Important!
The water softener must always be filled with granular salt made especially for dishwasher water softening systems. We do not recommend the use of cooking salt like table salt, rock salt or pellets as they may contain impurities that will impair or diminish the life of the water softener.
Water softening can only take place when there is salt in the reservoir. The salt reservoir must be filled prior to using the DishDrawer?? and whenever the salt indicator light is red.
Salt indicator light
If the salt indicator light is red, the salt reservoir is empty.
If the salt indicator light is black, there is enough salt in the reservoir for the wash programme that has been selected.
a
a Salt indicator light
bSalt reservoir cap
Important!
Do not pour detergent or rinse aid into the salt reservoir. Detergent and rinse aid will destroy the water softener.
Salt only
22 Option adjustments
The following options can be adjusted to suit your preferences:
Rinse aid setting
Reduce the Rinse aid setting if there is excess foam after a wash programme or if you are using dishwasher tablets with
Increase the Rinse aid setting if dishes are wet or streaky after a wash programme.
Water softener setting
Refer to the ???Water softener??? section.
Auto power setting
By default, DishDrawer?? will automatically turn on whenever the drawer is opened. Washing will not start until the drawer is closed and the 
button has been pressed. If you do not want the DishDrawer?? to turn on automatically, this feature can be turned off.
End of wash programme beeps
By default, DishDrawer?? will beep six times at the end of a wash programme. This feature can be turned off.
Closed drawer option
The Closed drawer option will lock the DishDrawer?? when the drawer is closed. When you wish to open the drawer, press the
/ 
button. When the drawer is fully closed again, the lid will automatically come down after 30 seconds and lock.
If the Keylock feature is used in conjunction with the Closed drawer option, pressing the
/ 
button will not unlock the drawer. The Keylock feature must be turned off to enable DishDrawer?? to be opened.
Note: this option is highly recommended if the DishDrawer?? is to be used in motor homes.
How to make option adjustments
2Press and hold the 
/ 
and 
/
buttons for 5 seconds until one long beep sounds.
* This option is disabled on models without water softener. It appears in the sequence of options but cannot be adjusted. ** The option sequence will start again from the Rinse aid setting.
23 adjustments Option
24 User maintenance instructions
Important!
Disconnect the DishDrawer?? from the power supply and allow all its parts to cool before any cleaning or maintenance.
Cleaning the surfaces
Important!
We do not recommend the use of the following cleaning aids on your DishDrawer?? as they may damage the surfaces:
1 Wipe with a clean damp cloth. Take care not to wet the control panel.
2Dry with a clean
Cleaning the drain filter
1 Unplug the DishDrawer?? or turn it off at the power supply.
2 Ensure the tines above the drain filter are in the upright position.
3Lift and remove the drain filter. It is normal to find some
water under it.
4 Empty, rinse clean under running water and replace back into the allocated space.
5 Ensure the drain filter is flush with the filter plate. 6 Plug the DishDrawer?? back in or turn it on at the
power supply.
User maintenance instructions 25
Cleaning the spray arms and filter plate
Ensure the DishDrawer?? is cool before you start cleaning.
To remove the base rack and spray arms
1 Unplug the DishDrawer?? or turn it off at the power supply.
2Take out the cutlery basket.
3Unclip the glass supports from the rack wires and fold all the adjustable racks away, so that they are upright and close to the top.
4Fold down all the tines.
5Remove the base rack carefully. Start lifting from the back first, tilting the rack as needed to clear the adjustable racks and the dispenser in the front.
6 Unclip the spray arms off their mounting valves and shake any foreign material out. 7 Rinse the spray arm clean under running water and wipe with a damp cloth.
8 If necessary, wipe any soiling off the filter plate with a clean, damp cloth.
To replace the spray arms and base rack
9Clip the spray arms back onto their mounting valves. Be careful that you don???t force them too hard, and apply too much pressure on the wash pump housing. You should hear them click into place. Rotate them with your hand to check that they are located properly.
10Replace the base rack, lowering its front edge into position first.
11Clip the glass supports back on and arrange the racking back to your preference.
12Plug the DishDrawer?? back in or turn it on at the power supply.
Note: Where there is broken crockery or glass in the drawer, it must be carefully removed to prevent damage to the DishDrawer??.
3
3
4
5 
6
6
Wash pump housing
Spray arm
Mounting valve
Filter plate
26 Troubleshooting
DishDrawer?? will Childlock feature is on or not openthe Closed drawer option is
on, or both.
Turn the Childlock off. Hold down the
/
button until the light above the
/
button disappears and/or press the
/ 
button to open the DishDrawer??.
The drawer is not closed properly.
Ensure the drawer is firmly closed.
long periods of time. Run the DishDrawer?? through a wash programme.
28 Fault codes
How to recognise a fault code
When a fault has occurred, the DishDrawer?? will continuously beep every second.
The fault code will be displayed on the wash programme selector.
Each fault code is shown in the following chart.
How to attend to a fault code
1Press the 
/
button briefly to stop the beeping.
2Press the 
/ 
button to turn the DishDrawer?? off. Wait a few seconds.
3Press the 
/ 
button to turn the DishDrawer?? back on.
Has the fault code disappeared? >YES > You can continue to use your DishDrawer??.
NO
4Open the DishDrawer and note down the fault code.
5Unplug the DishDrawer?? or turn it off at the power supply.
6Check the chart overleaf and try correcting the fault where possible, following the instructions in the ???What to do??? column.
Has the fault code disappeared? >YES > You can continue to use your DishDrawer??.
NO
7Unplug the DishDrawer?? or turn it off at the power supply.
8Call your Authorised Service Centre or Customer Care and advise them of the fault code. This information will help them respond to your request.
30 Fault codes
Warranty and service 31
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions and your user guide and check that:
1your product is correctly installed
2you are familiar with its normal operation.
If after checking these points you still need assistance, please refer to the Service & Warranty book for warranty details and your nearest Authorised Service Centre, or contact us through our website listed on the back cover.
Fisher & Paykel Appliances
32 Wash programme data
USA & CANADA
NEW ZEALAND AND AUSTRALIA
*Reference programme for energy label in compliance with AS/NZS 2007.
*Reference programme for energy label in compliance with EN50242 Regulations.
Note:
Wash times can vary depending on the incoming water temperature, ambient conditions, type of dish load and whether the drawer has been opened during the wash. Wash times are only APPROXIMATE on the electronic display and based on 120oF (USA and Canada), 20oC (New Zealand and Australia), or 15oC (Great Britain and Ireland) incoming water.
34 Standards test - USA and CANADA
The DishDrawer??s are tested to various standards for both wash and dry performance using the parameters detailed below.
Wash programme
Rinse agent setting
Maximum place setting
Accessories to be used in the dishwasher standards test
Recommended loading pattern
6 glasses under adjustable racks
Normal
4
9
Base rack,
3 glasses
4 cups under adjustable racks
Standards test - NEW ZEALAND and AUSTRALIA 35
The DishDrawer??s are tested to AS/NZS 2007 standards for both wash and dry performance using the parameters detailed below.
Detergent quantities
Rinse aid setting
Maximum place setting
Accessories to be used in the dishwasher standards test
Height setting of adjustable racks
H
Correct orientation of glass supports on both sides of drawer
Recommended loading pattern
26.25g (main wash)
4
9
Base rack,
H = 125 mm for the back
H = 140 mm for all the other adjustable racks
1 saucer3 cups + 1 glass under adjustable racks 5 glasses under adjustable racks
36 Standards test - GREAT BRITAIN and IRELAND
The DishDrawer??s are tested to EN50242 standards for both wash and dry performances using the parameters detailed below.
Height setting of adjustable racks
H
H = 125 mm for the back
H = 140 mm for all the other adjustable racks
Correct orientation of glass supports on both sides of drawer
small serving bowl
cup
2 glasses
cup
5 glasses under
www.fisherpaykel.com
www.fisherpaykel.ca
www.fisherpaykel.co.nz
www.fisherpaykel.com.au
www.fisherpaykel.co.uk
www.fisherpaykel.ie
Copyright ?? Fisher & Paykel 2010. All rights reserved.
The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.