WARNING

Prevent serious injury or death from falls or sliding out:

???The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair.

???It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position.

???Always keep child in view while using the high chair.

???Never leave child unattended.

???Do not use the high chair unless all components are correctly fitted and adjusted.

Prevent injury from burns: Do not place this high chair near open fires or any hot surfaces.

IMPORTANT! Place the high chair on a level, stable surface away from electrical flexes. Be sure to keep electrical flexes out of child's reach.

???Please read these instructions before assembly and use of this product.

???Adult assembly is required.

???Tool needed for assembly: Phillips Screwdriver (not included).

???Product features and decorations may vary from the photograph.

IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price?? for replacement parts and instructions if needed. Never substitute parts.

Footrest

Seat Bottom

1

???Place the seat bottom face down on a flat surface.

???At an angle, fit the footrest on the seat bottom, as shown.

Plastic Rings

Seat Bottom Tubes

3

???Align the holes in the plastic rings and the seat bottom tubes.

???Insert a #8 x 1,9 cm screw through each plastic ring and into the seat bottom tubes, as shown. Tighten the screws. This may require extra force.

???Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom. If the seat bottom tubes move, you have probably not fastened them properly. Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned. Replace and tighten the screws.

4

???Insert two #10 x 2,2 cm black screws through the footrest and into the seat bottom. Tighten the screws. This may require extra force.

Seat Back Pin

6

???Turn the seat assembly face down.

???Insert the hinge rod through the hinge on the seat back and seat bottom, as shown.

???Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten the screw.

???Set the seat assembly aside for Assembly step 9.

Frame Leg

Frame Decorated Side

Frame Back Legs

Base

Screw Retainers

Seat Height Adjusters

Position 4

Press Lever

8

???While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown.

Seat Assembly

7

???Pull the frame leg out on each frame to open. Make sure it "clicks" into place.

???Position a frame so that the decorated side is outward.

???Fit the end of a base into the back leg of a frame.

???Fit a screw retainer over the hole in the back leg, as shown.

???Insert a #10 x 2,2 cm black screw through the screw retainer and back leg. Tighten the screw.

???Repeat this procedure to fasten the other frame back leg to the other side of the base.

Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers.

Seat Bottom Tubes

9

???Fit the seat assembly between the frames.

???Insert the seat bottom tubes into the sockets in each seat height adjuster.

Hints:

???Be sure the seat height adjusters are in the same position (position 4).

???You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets.

Screw Retainers

???Fit the frame front legs onto the remaining base.

???Fit a screw retainer over a hole in the front leg.

???Insert a #10 x 2,2 cm black screw through the screw retainer and front leg. Tighten the screw.

???Repeat this procedure to secure the other end of the base with the remaining screw retainer and #10 x 2,2 cm black screw.

Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers.

Seat Height Adjuster

Seat Bottom Tube Ends

12

???Push each seat height adjuster to be sure they are completely on the seat bottom tubes.

???Insert a #8 x 1,9 cm screw through each seat height adjuster and the ends of the seat bottom tube. Tighten the screws. This may require extra force.

Pad

Elastic Loops

Hole Hole

FRONT VIEW

Tabs

???Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom.

???From the back and bottom of the seat, hook the elastic loops to the tabs on the seat.

Slot

Crotch Belt

14

???Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted.

Shoulder Portion

15

???Fold the top of the pad down.

???Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back.

Lower Shoulder Belt Slots

17

???Insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back.

-Use the lower shoulder belt slots for a smaller baby.

-Use the upper shoulder belt slots for a larger baby.

???Fit the top of the pad over the seat back.

???Fold the bottom edge of the pad under the edge of the seat bottom to fasten.

Bottom Slots

16

??? Lift the top of the pad.

??? Thread the waist/shoulder belts through the bottom slots in the back of the seat pad.

Belt Ends

18

???Place your child in the seat. Position the crotch belt between your child???s legs.

???Fasten both waist/shoulder belts to each side of the crotch belt. Make sure you hear a "click" on both sides.

???Check to be sure the restraint system is securely attached by pulling it away from your child. The restraint system should remain attached.

To tighten the waist belts:

???Feed the anchored end of the waist belt up through the buckle to form a loop A .

???Pull the free end of the waist belt B .

???Repeat this procedure to tighten the other waist belt.

To loosen the waist belts:

???Feed the free end of the waist belt up through the buckle to form a loop A .

???Enlarge the loop by pulling on the end of the loop toward the buckle.

???Pull the anchored end of the waist belt to shorten the free end of the waist belt B .

???Repeat this procedure to loosen the other waist belt.

Hold Adjuster

Pull Down Strap

Slide Adjuster Down

4

To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down.

To loosen the shoulder belts: Slide the adjuster down.

Note: After adjusting the restraint system to fit your child, make sure you pull on it to be sure it is securely fastened.

Shoulder Portion

6

???From the front of the high chair, pull the shoulder portion of the waist/shoulder belts out and then fit them back through the desired shoulder belt slots in the headrest pad, seat pad and the seat back.

???Pull on the belts to be sure they are secure in the seat back.

9

???While pushing the release bar on the front of the base tray, pull the tray base towards you and remove.

Food Tray

Base Tray

10

??? Fit the food tray into the base tray, as shown.

Hint: Before use, thoroughly wash all parts (the trays) that may contact food. The food tray is not microwave safe.

WARNING

Prevent serious injury or death from falls or sliding out: It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position.

Hint: Adjust the seat angle to any of three positions: Upright, Semi-Recline or Recline.

Upright

Semi-Recline

Recline

Hint: Adjust the seat height to any of seven positions!

Press Lever

12

To adjust the seat height:

???Press the levers on both seat height adjusters and lift or lower the seat to the desired height.

???Make sure both sides of the seat are adjusted to the same height. Push the seat bottom to be sure the seat is locked in place.

Pull Frame Release Latch

13

???With the legs all the way open, lower the seat to position 7 (the lowest position).

???Pull the frame release latches forward and push the rear legs toward the front legs.

???The restraint system, pad, frame, trays and tray toy may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach.

???The food tray is also top rack dishwasher safe (or use bottom rack - without using the drying cycle).

To remove the pad:

???Remove the elastic loops from the pegs on the back of the seat.

???From behind the product, squeeze the restraint release tabs and remove the restraint system from the peg.

???From the front of the product, pull to remove the restraint system.

???Unfasten the pad hooks from the front edge of the seat. Lift the top of the pad off of the seat back.

???To replace the pad: refer to assembly steps 13-17.

IMPORTANT! Never use this product without the restraint system. Replace the waist/shoulder belts and crotch belt.