Safety warnings

For the installer

???When used as an extractor unit, the hood must be fitted with a 150mm diameter hose.

Attention: The hose is not supplied and must be purchased separately.

???Should there already be a pipe of diameter 125 or 120 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125- 120 mm reduction flange provided. In this case the hood will be slightly noisier.

???When installing the hood, make sure you respect the following minimum distance

from the top edge of the cooking hob/ring

The hood can be installed above these heights but for optimum performance it should be installed at the distance quoted for the appropriate heat source.

???The national Standard on fuel-burning systems specifies a maximum depression of 0.04 mbar in such rooms.

???The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed.

???The air outlet installation must comply with the regulations laid down by the relevant authorities.

???When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approxi- mately the same as the outlet hole.

???National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room.

???Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approxi- mately 500-600 cm2 large to avoid the possibility of a depression being created during operation of the hood.

???If you have any doubts, contact the relevant controlling authority or building inspector???s office.

???Since the rule for rooms with fuel burning appliances is ???outlet hole of the same size as the ventilation hole???, a hole of 500-600 cm2, which is to say a larger hole, could reduce the perfor- mance of the extractor hood.

???If the hood is used in its filtering function, it will

operate simply and safely in the above conditions without the need for any of the aforementioned measures.

???When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation:

???short and straight outlet hose

???keep bends in outlet hose to a minimum

???never install the hoses with an acute angle, they must always follow a gentle curve.

???keep the hose as large as possible (preferably the same diameter as the outlet hole).

???Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood.

For the user

???The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.

???Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames.

???Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control.

???The hot oil in the frying pan might ignite due to overheating.

???The risk of self-ignition increases when the oil being used is dirty.

???It is extremely important to note that overheating can cause a fire.

???Never carry out any flamb?? cooking under the hood.

???Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker).

???It is very important to clean the hood and replace the filter at the recommended intervals. Failure to do so could cause grease deposits to build up, resulting in a fire hazard.

???The appliance is not intended for use by young children or infirm persons without supervision.

???Young children should be supervised to ensure that they do not play with the appliance.

???WARNING - Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

???The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.

???The hood is supplied as a filter unit (with charcoal filter already supplied and fitted) and can also be used with an extractor function function by removing the charcoal filter.

Extractor version

???In this version fumes are extracted to the outside via a hose connected to the coupling ring.

Attention: The hose is not supplied and must be purchased separately.

???Remove the grease filters and remove the Charcoal Filter from its housing by unscrewing the two screws that fix it to the hood. Refit the grease filters.

???In order to obtain the best performance the hose should have a diameter equal to the outlet hole. Should there already be a pipe of diameter 125 or 120 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125- 120 mm reduction flange provided. In this case the hood will be slightly noisier.

To the outside

Coupling ring

Hose

Coupling ring

Fig. 1 - Extractor version

Side grids

Recirculation Version

???The air is filtered through a charcoal filter and returned to the kitchen through the side grids.

???You will need an original Electrolux charcoal filter for this function (Available from your local Electrolux Service Force Centre).

???Fix the deflector using 2 screws ?? 3,5x6.5 mm.

???Fix the connection flange using 2 screws ?? 3,5x6.5 mm.

Chimney support

Deflector

Connection flange

Fig. 2 - Control Panel

Control Panel

ON/OFF Extractor fan

switch - Push button 1

Push button

Correct ventilation

If the cooker hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open.

Light switch Push button 3 2

Fig. 3 - Control Panel

Cleaning the hood

???Clean the outside of the hood using a damp cloth and a mild detergent.

???Never use corrosive, abrasive or flammable cleaning products.

???Never insert pointed objects in the motor???s protective grid.

???Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders.

???Only ever clean the control panel and filter grille using a damp cloth and delicate detergents.

???It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard.

Metal grease filter

???The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks.

Removing the metal grease filter

???First, push both metal grease filter handles

towards the centre, then extract the filter, pulling downwards.

Repeat the steps with the second filter.

Hand washing

Soak grease filters for about one hour in hot water with a little washing-up liquid, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry.

Dishwasher

Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65??C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance.

???Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes).

Warning

???Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions.

???The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

Metal grease filter handle

Fig. 4 - Removing the metal grease filter

Charcoal filter

???The charcoal filter is already supplied and mounted in place.

???The charcoal filter should only be used if you want to use the hood in the recirculation function.

???Only applicable for recirculation. The charcoal filters absorb smells and odours.

???The charcoal filter cannot be washed nor regenerated.

The charcoal filter should be replaced every 6

months under normal use.

Replacement filters are available from your local Service Force Centre.

Fitting:

???Unplug the unit or disconnect it from the power supply

???Remove the metal grease filter.

???Fit the charcoal filter and fix it to the body of the hood with two supplied screws.

???Refit the metal grease filters.

???To remove proceed in the reverse order.

???Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit.

???The charcoal filter can be ordered from your local ELECTROLUX Service Force Centre.

Fig. 5 - Fitting the Charcoal Filter

Installation

Unpacking

Check that the cooker hood has no damages. Transportation damages should immediately be reported to the company responsible for the transportation.

Damages, faults and eventually missing details should immediately be reported to the retailer. Take care of the packing materials so that small children cannot play with them.

Fitting

The hood is to be mounted on the wall.

When installed, the hood must be not less than 60 cm. above electric burners or 70 cm. above gas or mixed-fuel burners.

The hood can be installed above these heights but for optimum performance it should be installed at the distance quoted for the appropriate heat source.

Electrical connection for UK only

Safety warnings for the electrician

Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts.

The switch must be accessible at all times. The following is valid in the United Kingdom only:

-the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, -

-the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

15

Fig. 8 - Wall mounting

8

3