OPERATOR???S MANUAL
SNOW
THROWER
MODELS
850 SWE
1130 SWE
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered,
CUB CADET CORP. P.O. BOX 368023 CLEVELAND, OHIO
FINDING MODEL NUMBER
This Operator???s Manual is an important part of your new Snow Thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. The information on the model plate is very important if you need help from your local authorized Cub Cadet dealer.
You can locate the model number by looking at the lower frame cover on the rear of your snow thrower. A sample model plate is explained below. For future reference, please copy the model number and the serial number of the equipment in the space below.
CALLING CUSTOMER SUPPORT
If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Dealer Referral Line.
Call 1-
For more details about your unit, visit our website at www.cubcadet.com
2
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
Training
1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.
2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.
3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.
4.Never allow adults to operate this machine without proper instruction.
5.Thrown objects can cause serious personal injury. Plan your snow throwing pattern to avoid discharge of material toward roads, bystanders and the like.
6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.
7.Exercise caution to avoid slipping or falling, especially when operating in reverse.
Preparation
1.Thoroughly inspect the area where the equipment is to be used. Remove all door mats, newspapers, sleds, boards, wires and other foreign objects which could be tripped over or thrown by the auger/impeller.
2.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.
3.Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.
4.Use a grounded three wire extension cord and receptacle for all units with electric start engines.
5.Adjust collector housing height to clear gravel or crushed rock surfaces.
6.Disengage all clutch levers before starting the engine.
7.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator???s manual.
8.Let engine and machine adjust to outdoor temperature before starting to clear snow.
9.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.
a.Use only an approved gasoline container.
b.Extinguish all cigarettes, cigars, pipes and other sources of ignition.
c.Never fuel machine indoors.
d.Never remove gas cap or add fuel while the engine is hot or running.
e.Allow engine to cool at least two minutes before refueling.
f.Never over fill fuel tank. Fill tank to no more than ?? inch below bottom of filler neck to provide space for fuel expansion.
g.Replace gasoline cap and tighten securely.
h.If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting the engine.
i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. furnace, water heater, space heater, clothes dryer etc.).
j.Allow machine to cool 5 minutes before storing.
Operation
1.Do not put hands or feet near rotating parts, in the auger/ impeller housing or discharge chute. Contact with the rotating parts can amputate hands and feet.
2.The auger/impeller clutch lever is a safety device. Never bypass its operation. Doing so, makes the machine unsafe and may cause personal injury.
3
3.The clutch levers must operate easily in both directions and automatically return to the disengaged position when released.
4.Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.
5.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.
6.Do not operate machine while under the influence of alcohol or drugs.
7.Muffler and engine become hot and can cause a burn. Do not touch.
8.Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic.
9.Exercise caution when changing direction and while operating on slopes.
10.Plan your snow throwing pattern to avoid discharge towards windows, walls, cars etc. To avoid property damage or personal injury caused by a ricochet.
11.Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.
12.Do not overload machine capacity by attempting to clear snow at too fast of a rate.
13.Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.
14.Disengage power to the auger/impeller when transporting or not in use.
15.Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when in reverse.
16.If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating.
17.Disengage all clutch levers and stop engine before you leave the operating position (behind the handles). Wait until the auger/impeller comes to a complete stop before unclogging the discharge chute, making any adjustments, or inspections.
18.Never put your hand in the discharge or collector openings. Always use a clearing tool to unclog the discharge opening.
19.Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20.If situations occur which are not covered in this manual, use care and good judgment. Contact your dealer or telephone
Maintenance And Storage
1.Never tamper with safety devices. Check their proper operation regularly.
2.Disengage all clutch levers and stop engine. Wait until the auger/impeller come to a complete stop. Disconnect the spark plug wire and ground against the engine to prevent unintended starting before cleaning, repairing, or inspecting.
3.Check bolts, and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage.
4.Do not change the engine governor setting or
5.Snow thrower shave plates and skid shoes are subject to wear and damage. For your safety protection, frequently check all components and replace with original equipment manufacturer???s (O.E.M.) parts only. Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety.
6.Check clutch controls periodically to verify they engage and disengage properly and adjust, if necessary. Refer to the adjustment section in this operator???s manual for instructions.
7.Maintain or replace safety and instruction labels, as necessary.
8.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.
9.Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of auger/impeller.
10.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace ,clothes dryer etc.
11.Always refer to the operator???s manual for proper instructions on
Your Responsibility:
Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. The safety labels are given below for your reference.
4
SECTION 2: ASSEMBLING YOUR SNOW THROWER
NOTE: Any reference in this manual to the left or right side of the snow thrower is observed from the operator???s position.
Unpacking
???Remove screws from the top sides and ends of the shipping crate.
???Set panel aside to avoid tire punctures or personal injury.
???Remove and discard plastic bag that covers unit.
???Remove any loose parts included with unit (i.e., Operator???s Manual, etc).
???Roll unit out of crate.
Loose Parts
The augers are secured to the auger shaft with two shear bolts and hex lock nuts. If you hit a foreign object or ice jam, the snow thrower is designed so that the bolts may shear. Two replacement shear bolts and nuts are provided for your convenience. Store in a safe place until needed. See Figure 1.
Figure 1
Assembly
WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.
???Remove the lower two plastic wing nuts, cupped washers and carriage bolts from each side of the lower handle. See Figure 2.
Figure 2
???Raise the upper handle assembly until it locks over the lower handle.
???Look at the lower rear of the snow thrower frame to be sure all the cables are aligned with the cable roller guides.
???Secure the upper handle and lower handle with the two plastic wing nuts, cupped washers and carriage bolts previously removed and tighten the upper two plastic wing nuts. See Figure 3.
Figure 3
???Slide the shift rod connector down over the end of the lower shift rod. Tap the connector until it locks over the lower shift rod. See Figure 3.
NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or change directions.
???If not already attached, slip the cables that run from the handle panel to the chute into the cable guide located on top of the engine. See Figure 4.
Figure 4
???Unwrap the headlight wire, which is attached to the headlight beneath the handle panel.
???Wind the headlight wire around the right handle until excess slack is removed.
???Plug the wire from the headlight into the wire lead coming from the right side of the engine, beneath the fuel tank.
5
Final Adjustments
Auger Control Adjustment
Check the adjustment of the auger control as follows:
???Push forward on the auger control until the small rubber bumper contacts the upper handle. There should be slack in the cable. See Figure 5 .
???Release the auger control. The cable should be
straight. Make certain you can depress the auger control against the left handle completely without using excess force.
If adjustment is necessary, proceed as follows:
???Loosen the jam nut and thread the cable in (for less slack) or out (for more slack) as necessary. See Figure 5 .
???Recheck the adjustment before retightening the jam nut against the cable.
Figure 5
Skid Shoe Adjustment
The space between the shave plate and the ground can be adjusted by repositioning the skid shoes found on either side of the snow throwers auger housing. For close snow removal, place skid shoes in the low position. Use middle or high position when area to be cleared is uneven. See Figure 6.
IMPORTANT: It is NOT recommended that this snow thrower be operated on a gravel surface, as loose stones can be easily picked up and thrown by the machine. If you must operate on a gravel surface, ALWAYS adjust the skid shoes into the HIGH position to allow the shave plate maximum clearance.
Adjust skid shoes as follows:
???Loosen, but do NOT remove, the three hex nuts which fasten the skid shoe to the auger housing.
???Raise or lower the skid shoe to desired position.
NOTE: Make certain the entire base of both skid shoes are against the ground to avoid uneven wear on the skid shoes. When one side does wear out, the skid shoes are reversible.
Figure 6
???Retighten the hex nuts loosened earlier.
???Repeat this adjustment on the skid shoe found on the opposite side of the snow thrower.
Traction Control and Shift Lever Adjustment
To check the adjustment of the traction control and shift lever, proceed as follows:
???Move the shift lever into sixth (6) position.
a.With the traction control (refer to Figure 7) released, squeeze in triggers and gently push the snow thrower forward, then pull it back. Disregarding the overall weight of the snow thrower, the machine should otherwise move freely.
b.Engage the traction control and attempt to move them machine both forward and rearward. You should experience resistance as the wheels should not be turning.
???Move the shift lever into the fast reverse (R2) position and repeat the previous steps (a & b).
If you experienced resistance either when repositioning the shift lever from 6 to R2 or when attempting to move the machine forward or rearward with the traction control released, your snow thrower???s traction control is in need of adjustment and you should NOT operate the machine before completing the adjustment as follows:
???Loosen the jam nut on the traction control cable and UNTHREAD the cable one full turn.
???Recheck the adjustment.
???Retighten the jam nut to secure the cable when
correct adjustment is reached.
If the machine can be moved freely both forward and rearward when the traction control fully depressed, proceed as follows:
???Loosen the jam nut on the traction drive cable and THREAD the cable in one full turn.
6
???Recheck the adjustment and repeat adjustment as necessary.
???Retighten the jam nut to secure the cable when correct adjustment is reached.
NOTE: If you are uncertain that you have reached the correct adjustment, refer to Traction Control Adjustment in Adjustment Section.
SECTION 3: KNOW YOUR SNOW THROWER
Figure 7
WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.
Traction Control / Auger Control Lock
Chute Tilt Control
The distance snow is thrown can be changed by adjusting the angle of the chute assembly. Move the chute tilt control forward to decrease the distance, toward the rear to increase. See Figure 7.
The traction control is located on the right handle. Squeeze the traction control to engage the wheel drive. Release to stop. See Figure 7.
This same lever also locks the auger control so you can turn the chute directional control without interrupting the snow throwing process. If the auger control is engaged along with the traction control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release the traction control to stop both the augers and track drive (auger control must also be released).
IMPORTANT:Always release tractional control before changing speeds.
Auger Drive Control
The auger drive control is located on the left handle. Squeeze the control grip to engage the augers. Release to stop the snow throwing action. (Traction control must also be released.) See Figure 7.
Skid Shoe
The position of the skid shoe is determined by the condition of the ground from where snow has to be removed. See Figure 7.
Shift Lever
The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel. It can be moved into any of eight positions. See Figure 7.
Forward
Your snow thrower has six forward (F) speeds. Position number one (1) is the slowest. Position number six (6) is the fastest.
Reverse
Your snow thrower has two reverse (R) speeds. R1 is the slower, while R2 is the faster of the two.
IMPORTANT: Always release tractional control before changing speeds.
7
Electric
The electric
To change the direction in which discharged snow is thrown, proceed as follows:
???Push the toggle switch to the left to rotate the chute counterclockwise.
???Push the toggle switch to the right to rotate the chute clockwise.
IMPORTANT: Release the switch once the chute has completed its rotation cycle in either direction. Failure to do so can result in damage to the electric chute motor and/or its drive gear.
Heated Handles Switch
The heated handles switch is located on the right side of the snow thrower handle panel. To activate the heated handles, toggle the switch to the right to generate heat within the handles. Toggle the heated handles switch to the left into the OFF position after using the snow thrower.
NOTE: The heated handles are a compliment to, not a substitute for, proper cold weather outerwear for hands. It is recommended that the user wear adequate winter protection for hands (like gloves/mittens) when operating this snow thrower.
Wheel Steering Controls
The left and right wheel steering controls are located on the underside of the handles and are used to assist in steering the snow thrower. Squeeze the right wheel steering control when turning right, squeeze the left control when turning left. Operate your snow thrower in open areas until you become familiar with these controls. See Figure 7.
NOTE: It is easier to maneuver a
Headlight
The headlight is on whenever the engine is running.
Throttle Control
The throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down completely. See Figure 7.
Safety Ignition Key
The safety ignition key must be fully inserted in the switch before the unit will start. Remove the ignition key when the snow thrower is not in use. See Figure 7.
IMPORTANT: Do NOT attempt to turn the key.
SECTION 4: OPERATING YOUR SNOW THROWER
WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.
Gas And Oil
Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.
WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes an other sources of ignition.
???A plastic cup is provided inside the fuel fill opening on the fuel tank. Remove and discard this cup before filling up the tank. Use the separate fuel tank cap to close after
NOTE: If unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut engine off immediately. Readjust as instructed in the Final Adjustments in the Assembly Section.
???Attach spark plug wire to spark plug. Make certain the metal loop on end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug.
???Make certain the auger and drive clutch levers are in the disengaged (released) position.
???Move throttle control up to FAST position. Insert ignition key into slot. See Figure 7. Be certain it snaps into place. Do not turn key.
NOTE: Engine will not start unless ignition key is inserted into ignition slot in carburetor cover.
Electric Starter
???Determine that your house wiring is a
8
WARNING: The electric starter is equipped with a grounded
???If your house wiring system is not a
???If your home electrical system is grounded, but a
???If you have a grounded
???Rotate choke knob to OFF position and do not prime engine.
???Connect power cord to switch box on engine. Plug the other end of power cord into a
???Push starter button on top of the engine to crank engine. As you crank the engine, move choke knob to FULL choke position.
???When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF.
???When disconnecting the power cord, always unplug from the
Recoil Starter
???Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.
???Push primer button two or three times. If engine is warm, push primer button once only.
NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15??F.
???Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.
???Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.
???Repeat the previous steps until engine starts.
To Stop Engine
???Run engine for a few minutes before stopping to help dry off any moisture on the engine.
???To help prevent possible
Electric Starter:
???Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.
Recoil Starter
???With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.
???Move throttle control to ???stop??? or ???off??? position.
???Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.
NOTE: Keep it in a safe place. Engine will not start without ignition key.
Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.
To Engage Wheel Drive
???With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.
NOTE: Use slower speeds in higher snow, and until you are familiar with the operation of the snow thrower.
???Squeeze the traction control against the right handle and the snow thrower will move. Release it and the drive motion will stop.
IMPORTANT: NEVER move the shift lever without first releasing the traction control. Doing so will cause premature wear to the drive system???s friction wheel.
To Engage Augers
To engage the augers and start the snow throwing action, proceed as follows:
???Squeeze the auger control against the left handle. To disengage power to the augers:
???Release both the auger control and the traction control, if engaged.
The auger control can be locked so you can turn the electric chute directional control without interrupting the snow throwing process.
Operating Tips
NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.
9
WARNING: The temperature of the muffler and the surrounding areas may exceed
150??F. Avoid these areas.
???For the most efficient snow removal, remove snow immediately after it falls.
???Discharge the snow downwind whenever possible.
???Slightly overlap each previous path.
???Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for
SECTION 5: MAKING ADJUSTMENTS
WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator???s manual.
Chute Assembly Adjustment
The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Chute Tilt Control in the Know Your Snow Thrower Section.
Traction Control Adjustment
Refer to the information found under Final Adjustment in the Assembly Section to adjust the traction control. If you are uncertain that you have reached the correct adjustment, proceed as follows:
WARNING: Drain the gasoline out of the snow thrower???s tank, or place a piece of plastic film under the gas cap to avoid spillage BEFORE making the adjustment.
???Tip the snow thrower forward, allowing it to rest on the auger housing.
???Remove the frame cover underneath the snow thrower by removing the six
???With the traction control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever.
???With the traction control engaged, the friction wheel must contact the drive plate. See Figure 8.
Figure 8
If adjustment is necessary:
???Loosen the jam nut on the traction drive cable and adjust the cable as necessary. Refer to Figure 5.
???Retighten the jam nut to secure the cable when correct adjustment is reached.
???Reassemble the frame cover.
NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower.
Shift Rod Adjustment
To adjust the shift rod, proceed as follows:
???Remove the hairpin clip and slide the shift rod connector up, to separate the upper shift rod from the lower shift rod. See Figure 9.
Figure 9
???Place the shift lever into the sixth (6) position.
???Rotate the shift arm clockwise (from the operator???s position) as far as it will go.
???Thread the upper shift rod downward until the elbow on its lower end aligns with the hole found in the lower shift rod.
10
???Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding the shift rod connector back down into place.
IMPORTANT: Make certain to check for correct adjustment of the shift rod as instructed under Final Adjustments in the Assembly Section, before operating the snow thrower.
Drive Wheels
The wheels may be adjusted for two different methods of operation. The adjustment is made by placing the click pins in one of two different holes on the right side of the unit. See Figure 10.
One Wheel Driving: Insert the click pin only through the outside hole of the axle (NOT the rim) on the right side of the snow thrower. This position gives power drive to the left wheel only, making the unit easier to maneuver.
Both Wheels Driving: Insert the click pin through the hole in the hub of the rim and the INSIDE hole on the snow thrower???s right axle. This position is good for heavy snow as there is power drive in both wheels.
IMPORTANT: NEVER operate the snow thrower with the click pin inserted through both the RIM and the OUTSIDE HOLE in the axle. Doing so can result in serious damage to the drive system.
Figure 10
Skid Shoe Adjustment
The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes. Refer to Skid Shoe Adjustment in the Assembly Section.
Auger Control Adjustment
Refer to the information found under Final Adjustments in the Assembly Section to adjust the auger control.
SECTION 6: MAINTAINING YOUR SNOW THROWER
WARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.
Lubrication
Engine
Refer to the separate engine manual packed with your unit for all engine lubrication instructions.
IMPORTANT: When following instructions in separate engine manual for draining oil, be sure to protect frame to avoid oil dripping onto transmission parts.
Gear Shaft
Lubricate the gear shaft with
Refer to Figure 8.
IMPORTANT: Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.
Drive and Shifting Mechanism
Lubricate at least once a season or after every 25 hours of operation. Remove the rear cover, lubricate any chains, sprockets, gears, bearings, shafts, and shifting mechanism at least once a season. Use engine oil or a spray lubricant. Avoid getting oil on the friction wheel rubber and aluminum drive plate. Refer to Figure 8.
There is a grease fitting on the top of the axle shaft which drives the rear track drive wheels on both sides of the unit. Grease these fittings every 25 hours or once a season.
Traction Control / Auger Control Lock
The cams on the ends of the control rods which interlock the traction drive and auger drive controls must be lubricated at least once a season or every 25 hours of operation. The cams can be accessed beneath the handle panel. Use a
Electric
The gear on the electric
11
Figure 11
Gear Case
The gear case is equipped with a grease fitting on the left housing and should be lubricated with Shell Alvania grease EPR00, part number
Do not overfill the gear case. Damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.
Auger Shaft
At least once a season, remove the shear bolts on the auger shaft. Spray lubricant inside the shaft. Also lubricate the plastic auger bearings at least once a season and grease the fittings on the end of the auger shaft with a standard grease gun. See Figure 12.
Figure 12
SECTION 7: SERVICING YOUR SNOW THROWER
WARNING: Before servicing, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.
Engine
Refer to the separate engine manual packed with your unit for all engine maintenance procedures.
Augers
???The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a hard foreign object or ice jam, the snow thrower is designed so that the bolts may shear.
Refer to Figure 12.
???If the augers will not turn, check to see if the bolts have sheared. Replacement shear bolts and hex lock nuts have been provided with the snow thrower. When replacing bolts, spray an oil lubricant into shaft before inserting new bolts.
IMPORTANT:NEVER replace the auger shear bolts with standard hex bolts. Any damage to the auger gearbox or other components as a result of doing so will NOT be covered by your snow thrower???s warranty.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove the skid shoes, proceed as follows:
???Remove the six carriage bolts, bell washers, and hex nuts which attach them to the snow thrower.
???Reassemble new skid shoes with the six carriage bolts, bell washers (cupped side goes against skid
shoes) and hex nuts. Make certain the skid shoes are adjusted to be level.
To remove shave plate, remove the carriage bolts, bell washers, and hex nuts which attach it to the snow thrower housing. Reassemble new shave plate, making sure heads of the carriage bolts are to the inside of the housing. Tighten securely.
Belt Removal And Replacement
Auger Belts
???Remove the plastic belt cover at the front of the engine by removing the two
???Drain the gasoline from the snow thrower, or place a piece of plastic film under the gas cap.
???Tip the snow thrower up and forward so that it rests on its auger housing.
12
Figure 13
???Remove the six
???Roll the front and rear auger belts off the auger drive pulley. See Figure 14.
Figure 14
???Unhook the idler spring from the hex bolt on the auger housing. See Figure 14.
???Back out the stop bolt until the support bracket rests on the auger pulley.
NOTE: Loosening the six nuts that connect the frame to the auger housing may aid in belt removal.
???Lift the rear auger belt from the auger pulley, and slip the belt between the support bracket and the auger pulley. Repeat this step for the front auger belt.
???Replace both auger drive belts by following instructions in reverse order.
NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower.
Drive Belt
???Follow the first four steps of the instructions for servicing the auger belts.
???Pull the idler pulley up and lift the belt off the wheel drive pulley and friction wheel disc. See Figure 14.
???Back out the stop bolt until the support bracket rests on the auger pulley. See Figure 15.
???Slip the belt between the friction wheel and drive disc. Remove and replace the belt. Reassemble following the instructions in reverse order.
NOTE: The support bracket must rest on the stop bolt after the new belt has been assembled.
Figure 15
Replacing Friction Wheel Rubber
The rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation, and periodically thereafter. Replace the friction wheel rubber if any signs of wear or cracking are found.
???Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.
???Tip the snow thrower up and forward, so that it rests on the housing.
13
???Remove the six
???Remove the click pin that secures the left wheel to the axle and slide the wheel from the axle.
???Remove the four screws securing the left drive cover to the frame. Remove the drive cover. See Figure 16.
Figure 16
???Holding the friction wheel assembly, slide the hex shaft out of the left side of the frame. The spacer on the right side of the hex shaft will fall and the sprocket should remain hanging loose in the chain. See Figure 17.
Figure 17
???Lift the friction wheel assembly out between the axle shaft and the drive shaft assemblies.
???Remove the six screws from the friction wheel assembly (three from each side). Remove the friction wheel rubber from between the friction wheel plates. See Figure 18.
???Reassemble the new friction wheel rubber to the friction wheel plates and hub, tightening the six screws in rotation and with equal force.
???Position the friction wheel assembly up onto the pin of the shift rod assembly, and slide the hex shaft through the friction wheel assembly. Reassemble in reverse order.
Figure 18
WARNING: Never store the machine or fuel container indoors where there is an open flame, spark, or pilot light such as on water heater, furnace, clothes dryer, or other gas appliance.
WARNING: Drain fuel into an approved container outdoors, away from an open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other sources of ignition prior to draining fuel. Fuel left in engine for extended periods deteriorates and will cause starting problems.
If unit is to be stored over 30 days, prepare for storage as follows:
???Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.
???Run engine until fuel tank is empty and engine stops due to lack of fuel.
???Drain carburetor by pressing upward on bowl drain, located below the carburetor cover.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Do not drain carburetor if using fuel stabilizer.
???Wipe equipment with an oiled rag to prevent rust.
???Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover spark plug hole with rag. Crank engine several times to distribute oil. Replace spark plug.
???Follow the lubrication recommendations found in the Maintenance Section.
???Always store the snow thrower in a clean, dry area.
NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.
14
SECTION 8: TROUBLE SHOOTING
15
Notes
16
Models 826 SWE & 1130 SWE
17
Models 826 SWE & 1130 SWE
57
3
50 9
40
16
4
1
18
Models 826 SWE & 1130 SWE
Ref.
No.
Part No.Part Description
1.
20.
21.
38.
40.
52.
54.
75.
19
Models 826 SWE & 1130 SWE
18
15
3
4
11 10
9
2 1
5
6
14
13
8
34
27
28
9
13
16 22
23
21
10
25
23
26
38
37
39
35
18
36 41
31
16
17
40
30
19 22
32
33
40
42
39
29
24
20
20
Models 826 SWE & 1130 SWE
4.
15.
33.
37.
38.
41.
42.
NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered
Cub Yellow: 0716
Cub Beige: 0499
Cub Blue: 0685
Powder Black: 0637
21
26
16
11
12
9
10
3
4
8 
4 7
19 15
16
16
19
16
21
22 
14
20
24
IMPORTANT: For a proper working machine, use Factory Approved Parts.
6 5
13
31 33
25
34
32
35
22
Models 826 SWE & 1130 SWE
25.
31.
23
Models 826 SWE & 1130 SWE
24
Models 826 SWE & 1130 SWE
Ref.
No.
Part No.Part Description
1.
2.
3.
4.
5.
7.
8.
45.
49.
50.
NOTE: For painted parts, please refer to the list of color codes below. Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered
Cub Yellow: 0716
Cub Beige: 0499
Cub Blue: 0685
Powder Black: 0637
25
26
27
MANUFACTURER???S LIMITED WARRANTY FOR:
Proper maintenance of your Cub Cadet equipment is the owner???s responsibility. Follow the instructions in your operator???s manual for correct lubricants and maintenance schedule. Your Cub Cadet dealer carries a complete line of quality lubricants and filters for your equipment???s engine, transmission, chassis and attachments.
Riding mowers, lawn tractors, garden tractors, Cub Cadet attachments and home maintenance products
This limited warranty for residential users, covers any defect in materials or workmanship in your Cub Cadet equipment for two years from the date of purchase for the first user purchaser. We will replace or repair any part or parts without charge through your authorized Cub Cadet dealer.
Batteries have a
Cub Cadet equipment used commercially is warranted for one year only.
(Commercial use is defined as either having hired operators or used for income producing purposes.)
Items not covered
The warranty does not cover routine maintenance items such as lubricants, filters (oil, fuel, air and hydraulic), cleaning,
There is no other express warranty.
How to obtain service
Contact your authorized Cub Cadet servicing dealer who sold you your Cub Cadet equipment. If this dealer is not available, see the Consumer Yellow Pages under ???lawn mowers??? for the name of a dealer near you.
If you need further assistance in finding an authorized Cub Cadet servicing dealer, contact:
Cub Cadet Corporation
Post Office Box 368023
Cleveland, Ohio 44136
How does state law apply?
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.