12V e GROUND

AM 530-1710kHz/FM 87.9-107.9MHz

THIS DEVICE COMPLIES WITH PART'5 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLL~NG lWO CONDITIONS:

(1)THIS OEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2)THIS DEViCE MUST ACCEPT my INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION

THIS PRODUCTION COMPLIES WITH OHHS RULES 21 CFR

SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.

CLARION CO_,l TO

7-2. SHINTOSHIN,CHUO-KU.SAITAMA-~I.SAITAM" 330-0081 ,JAPAN

This product includes technology owned by

Microsoft Corporation and cannot be used or distributed without a license from MSlGP.

MANUFACTURED

o

Bottom View of Source Unit Fond de I'appareilpilote

Vista inferior de la unidad fuente

1.FEATURES

IAACI IUS~tHI rB!fINET

~ IQl Madefor

'R'A~IO-' @J iPod

REA D Y

???USB Audio for iPod??

???USB Digital Media Streaming Capability

???Built-in LPF/HPF

*"iPod" is for legal or rightholder-authorized copying only. Don'tsteal music. "iPod" is a trademark of Apple Inc., registered in the U.S. and other countries.

*XM and the XM logos are trademarks of XM Satellite Radio Inc.

.

RI?~

ID3TAG

2.PRECAUTIONS

1.When the inside of the car is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about one hour. The condensation will disappear naturally allowing normal operation.

2.Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip.

3.This unit uses a precision mechanism. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts.

A CAUTION

USE OF CONTROLS, ADJUSTMENTS, OR

PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN, MAY

RESULT IN HAZARDOUS RADIATION

EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT

BE ADJUSTED OR REPAIRED BY ANYONE

EXCEPT PROPERLY QUALIFIED SERVICE

PERSONNEL.

CHANGES OR MODIFICATIONS NOT

EXPRESSLY APPROVED BY THE

MANUFACTURER FOR COMPLIANCE

COULD VOID THE USER'SAUTHORITY TO

OPERATE THE EQUIPMENT.

INFORMATION FOR USERS:

CHANGES OR MODIFICATIONS TO THIS

PRODUCT NOT APPROVED BY THE

MANUFACTURER WILL VOID THE

WARRANTY AND WILL VIOLATE FCC

APPROVAL.

Handling Compact Discs

Use only compact discs bearing the [Q]D~?? or

Storage

ffilm mark.

~

DIOITALAUDIO

Do not play heart-shaped, octagonal, or other specially shaped compact discs.

Some CDs recorded in CD-R/CD-RW mode may not be usable.

Handling

???Compared to ordinary music CDs, CD-R and CD-RW discs are both easily affected by high temperature and humidity and some of CD-R and CD-RW discs may not be played.

Therefore, do not leave them for a long time in the car.

???New discs may Ball-point pen have some

roughness Roughness

around the -~--........._~-,.,"'--

edges. If such discs are used, the player may not work or the

sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc.

???Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen.

???Never playa compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player.

???Do not use compact discs that have large scratches, are misshapen, cracked, etc. Use of such discs may cause misoperation or damage.

???To remove a compact disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges.

???Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may damage the disc or cause breakdown of the internal mechanism.

Cleaning

???To remove fingermarks and dust, use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference.

???Do not use any solvents, such as commercially available cleaners, anti-static spray, or thinner to clean compact discs.

???After using special compact disc cleaner, let the compact disc dry off well before playing it.

[RELEASE] ~(::;(~fD~~

[~] (EJECT)-7-~

[RELEASE] button

???Press the [RELEASE] button to unlock the DCP.

[rNI~] button

???Perform preset scan while in the radio mode. When the button is pressed and held, auto store is performed.

???Play or pause a track while in the CD/MP31 WMAlAAC mode.

???Confirm various settings.

[~](UP), [~] (ON) buttons

???Select the folder while in the MP3IWMAlAAC mode.

???Use the buttons to perform various settings.

[IR RECEIVER]

???Receiver for remote control unit. (Operating range: 30?? in all directions)

[CD SLOT]

??? CD insertion slof.

[USB SLOT]

???USB memory/MTP/iPod devices insertion slot.

[AUX] input jack

???The input jack for connecting an external device.

[USB SLOT]

&IlJlt.-.;.:.;..-..;;- [AUX]

~~J)

L..-_ [SOUND]

L..-_ [DIRECT]

L..--[RDM] L..--[RPT]

L..--[SCN]

[SOUND] button

???Use the button to switch to the sound adjust mode.

???Press and hold the button for 1 second or longer to turn on or off the MAGNA BASS EXTEND mode.

[DIRECT] buttons

???Store a station into memory or recall it directly while in the radio mode.

[ROM] button

???Perform random play while in the CD/MP31 WMAlAAC mode.

???Press and hold the button for 1 second or longer to perform folder random play while in the MP3IWMAlAAC mode.

[RPT] button

???Perform repeat play while in the CD/MP31 WMAlAAC mode.

???Press and hold the button for 1 second or longer to perform folder repeat play while in the MP3IWMAlAAC mode.

[SCN] button

???Perform scan play for 10 seconds of each track while in the CD/MP3/wMAlAAC mode.

???Press and hold the button for 1 second or longer to perform folder scan play while in the MP3/wMAlAAC mode.

[ISR] button

???RecalliSR radio station in memory.

???Press and hold the button for 2 seconds or longer: Store current station into ISR memory (radio mode only).

[DISP] button

???Switch the display indication.

???Press and hold the button for 1 second or longer to enter the adjust mode.

[ROTARY] knob

???Adjust the volume by turning the knob clockwise or counterclockwise.

[BND] button

???Switch the band, or seek tuning or manual tuning while in the radio mode.

???Playa first track while in the CD/MP3/wMAI AAC mode.

???Press the button to change the character.

[SRC] button

???Press the button to turn on the power.

???Press and hold the button for 1 second or longer to turn off the power.

???Switch the operation mode among the radio mode, etc.

[~], [~] buttons

???Select a station while in the radio mode or select a track while in the CD/MP3/wMAlAAC mode.

This button is used to make various settings.

???Press and hold the button for 1 second or longer to enter the fast-forward or fast- backward mode.

[~](EJECT) button

???Eject a disc when it is loaded into the unit.

MUTE indication

SAT Satellite indication

ICHI Channel indication

ICATI Category indication

MANU Manual indication

AAC

The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.

We recommend taking the DCP with you when leaving the car.

Storing the DCP in the DCP Case

Hold the DCP, in the orientation as shown in the figure below, and put it into the supplied DCP case. (Ensure the DCP is in the correct orientation.)

*The OCP is unlocked

3.Remove the OCP.

Attaching the DCP

1.Insert the right side of the OCP into the main unit.

2.Insert the left side of the DCP into the main unit.

ACAUTION

???The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks.

???When the Release button is pressed and the DCP is unlocked, the car'svibrations may cause it to fall. To prevent damage to the DCP, always store it in its case after detaching it.

???The connector connecting the main unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

OCP

connector

Note:

???If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.

[SRC] button

???Press the button to turn on the power. Press and hold the button for 1 second or longer to turn off the power.

???Use to alternate operation mode among the various modes.

LA], [....] buttons

??? Increases and decreases volume.

[MUTE] button

??? Turns mute function on and off.

[ISR] button

???Recalls ISR radio station stored in memory.

???Press and hold the button for 2 seconds or longer to store current station in ISR memory (radio mode only).

[BND] button

???Switches reception band.

[~], [~] buttons

???Moves preset channels up and down.

[SCN] button

???Press to perform preset scan.

???Press and hold the button for 2 seconds or longer to perform auto store.

???In the Satellite Radio mode, press once to perform category scan; hold depressed for 1 second or longer to perform preset scan.

???CDIMP3/WMAIAAC and USB/MTP modes

[BND] button

[DISP] button

??? Press to select the desired display.

???Press to play the first track.

[~], [~] buttons

???Press to move the tracks up and down.

???Press and hold the button for 1 second or longer to perform fast-forward/fast-backward (Except DRM file).

???When in MP3IWMAlAAC and USB/MTP modes, press and hold the button for 1 second or longer to perform folder random play.

???CD changerlDVD changer modes

[BND] button

???Press to switch to next disc in ascending order.

[~], [~] buttons

???Press to move the tracks up and down.

???Press and hold the button for 1 second or longer to perform fast-forward/fast-backward.

??? TV mode

[BND] button

???Switches reception band.

[~], [~] buttons

???Moves preset channels up and down.

[SCN] button

???Press to perform preset scan.

???Press and hold the button for 2 seconds or longer to perform auto store.

[ROM] button

??? Press to alternate between TV and VTR.

into place.

Notes:

Insertion guide

Basic Operations

Be sure to lower the volume before switching off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and damage the unit.

Turning on/off the power

Note:

???Be careful about using this unit for a long time without running the engine. If you drain the car's battery too far, you may not be able to start the engine and this can reduce the service life of the battery.

1.Press the [SAC] button.

2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.

3.Press and hold the [SAC] button for 1 second or longer to turn off the power for the unit.

Note:

???System check

The first time this unit is turned on after the wire connections are completed, it must be checked what equipment is connected. When the power is turned on, the "S-CHECK" appears in the display, then the unit returns to the clock display mode. The system check starts within the unit. Then press the {SRCj button again, the unit turn to the radio mode.

Selecting a mode

1.Press the [SAC] button to change the operation mode.

2.Each time you press the [SAC] button, the operation mode changes in the following order:

Radio'"(Satellite radio) CD/MP3/wMA/ AAC ... USB/MTP/iPod (CD changer) ...

(DVD changer) ... (TV) AUX ... Radio .

*External equipment not connected with CeNET is not displayed.

*iPod/MTP can connect to this unit via USB SLOT.

Adjusting the volume

1.Turning the [AOTAAY] knob clockwise increases the volume; turning it counterclockwise decreases the volume.

*The volume level is from 0 (minimum) to 33 (maximum).

Switching the display

Press the [DISP] button to select the desired display.

*Once selected, the preferred display becomes the display default. When a function adjustment such as volume is made, the screen will momentarily switch to that function'sdisplay, then revert back to the preferred display several seconds after the adjustment.

*If the button operation is performed with the screen saver function on, the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display.

For details, refer to the subsection "Turning the screen saver function on or off'in section "Operations Common to Each Mode".

Basic Operations

Sound Adjustment

You can adjust a sound effect or tone quality to your preference.

To change sound setting

1.Press the [SOUND] button to switch to the sound adjustment selection display.

*The factory default sound setting is "Z- EHCR".

2.Then press the [~....] or [~] button to select the sound adjustment mode. Each time you press the [~] or [~] button, the sound adjustment mode changes as following order:

"Z-EHCR" +--+ "BASS" +--+ "TREBLE" +--+ "BALANCE" +--+ "FADER" +--+ "S-W LPF" +--+ "S-W VOL" +--+ "HPF"

*In the case of display blinking "ENT", you can press the [:-r1~] button to adjust the setting value.

*The sound adjustment mode will be displayed for 2 seconds before showing the sound setting.

3.Press the LA] or [T] button to adjust the selected audio mode.

4.After completing settings, press the [SOUND] button to return to the previous mode.

???Setting the Z-Enhancer Plus

This unit is provided with 4 types of sound tone effects stored in memory.

Select the one you prefer.

* The factory default setting is "OFF". 2-1. Select "Z-EHCR".

3-1. Each time you press the [A] or [T] button, the tone effect changes in the following order:

"Z+FLAT" +--+ "CUSTOM" +--+ "EXCITE" +--+ "IMPACT'+--+ "B-BOOST'+--+ "OFF"

When "Z+FLAT" is set:

3-2. Press and hold the [~r1~] button for 1second or longer, bass/treble characteristics become flat and switch to the "CUSTOM" mode.

When "CUSTOM" is set:

3-1. Press the [~] or [~] button to select the "BASS" or "TREBLE" mode to adjust.

When "EXCITElIMPACT/B-BOOST" is set: 3-2. Press the [:-NI~] button.

3-3. Press the [A] or [T] button to adjust the setting in the range of -3 to +3.

* The factory default setting is "0".

3-4. Press the [~NI~] button to return to the previous mode.

??? Adjusting the bass

This adjustment can be performed only when the Z-Enhancer Plus is set to "CUSTOM ".

2-1. Select "BASS".

3-1. Press the [A] or [T] button to select as following order.

"BASS<G>" +--+ "BASS<F>" .-. "BASS<Q>"

* The factory default setting is "BASS<G>". 3-2. Press the [:-r1~ ] button.

3-3. Press the [A] or [T] button to adjust the gain, the F (center frequency) and the Q.

BASS<G>

:The factory default setting is "0". (Adjustment range: +7 to -7)

BASS<F>

:The factory default setting is "60". (Adjustment range: 60/80/100/200)

BASS<Q>

:The factory default setting is "1". (Adjustment range: 1/1.25/1.5/2)

3-4. Press the [:-r1~] button to return to the previous mode.

Basic Operations

??? Adjusting the treble

This adjustment can be performed only when the Z-Enhancer Plus is set to "CUSTOM ".

2-1. Select "TREBLE".

3-1. Press the L6.] or [T] button to .select as following order.

"TREB<G>" ~ ''TREB<F>''

* The factory default setting is ''TREB<G>''. 3-2. Press the [:-J~] button.

3-3. Press the L6.] or [T] button to adjust the gain, the F (center frequency) and the Q.

TREB<G>:The factory default setting is "0". (Adjustment range: +7 to -7)

TREB<F>: The factory default setting is "10k".

(Adjustment range: 10k/12.5k/15k/17.5k)

3-4. Press the [:-NI~] button to return to the previous mode.

??? Adjusting the balance

2-1. Select "BALANCE".

3-1. Press the LA.] or [T] button to adjust the balance of the right and left speakers.

*The factory default setting is "CENTER" (center). (Adjustment range: RIGHT12 to LEFT12 (right 12 to left 12))

???Adjusting the fader

2-1. Select "FADER".

3-1. Press the LA.] or [T] button to adjust the balance of the rear and front speakers.

*The factory default setting is "CENTER" (center). (Adjustment range: FRONT12 to REAR12 (front 12 to rear 12))

???Setting the subwoofer

You can set the low pass filter of subwoofer. 2-1. Select "S-W LPF".

3-1. Each time press the [6.] or [T] button to select the setting, the setting changes in the following order:

"THROUGH" ~ "LPF 50" ~ "LPF 80" ~ "LPF 120"

* The factory default setting is "THROUGH".

??? Adjusting the subwoofer output volume

You can adjust the volume output from the unit's subwoofer output terminal.

This adjustment can be performed only when the "S-W LPF" is set to "LPF 120", "LPF 80" or "LPF 50".

2-1. Select "S-W VOL".

3-1. Press the L6.] or [T] button to increases or decreases the subwoofer volume.

*The factory default setting is "0". (Adjustment range: +6 to -6)

*When the volume level is more than 30, the subwoofer volume adjustment value can not reach +6.

???Adjusting the high pass filter

2-1. Select "HPF'.

3-1. Each time you press the [6.] or [T] button to select the setting.

The setting changes in the following order: "120" H ''THROUGH''

*The factory default setting is "THROUGH" (through).

*This is supported only with amplifiers equipped with this function. Output is not supported from RCA cables.

Note:

???During SOUND adjustment mode, if no operation is performed for more than 10 seconds, this mode can be cancelled and return to previous mode.

Setting the MAGNA BASS EXTEND

The MAGNA BASS EXTEND does not adjust the low frequencies like the normal sound adjustment function, but emphasizes the deep bass frequencies to provide you with a dynamic sound.

*The factory default setting is "OFF'(off).

1.Press and hold the [SOUND] button for 1 second or longer to turn on the MAGNA BASS EXTEND effect. "M-B EX" appears in the display for 2 seconds.

2.Press and hold the [SOUND] button for 1 second or longer to turn off the MAGNA BASS EXTEND effect.

Radio Operations

Listening to the radio

1.Press the [SRC] button and select the radio mode. The frequency appears in the display.

2.Press the [BND] button and select the radio band. Each time the button is pressed, the radio reception band changes in the following order:

F1 (FM1) ~ F2 (FM2) ~ F3 (FM3) ~ AM ~ F1 (FM1 )...

3.Press the [~] or [~] button to tune in the desired station.

Tuning

There are 3 types of tuning mode available, seek tuning, manual tuning and preset tuning.

Seek tuning

1.Press the [BND] button and select the desired band (FM or AM).

*If "MANU" is lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available.

2.Press the [~....] or [~] button to automatically seek a station.

When the [~] button is pressed, the station is sought in the direction of higher frequencies; if the [~....] button is pressed. the station is sought in the direction of lower frequencies.

Manual tuning

There are 2 ways available: Quick tuning and step tuning.

When you are in the step tuning mode, the frequency changes one step at a time. In the quick tuning mode, you can quickly tune the desired frequency.

1.Press the [BND] button and select the desired band (FM or AM).

*If "MANU" is not lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" is lit in the display and manual tuning is now available.

2.Tune into a station.

??? Quick tuning

Press and hold the [~] or [~] button for 1 second or longer to tune in a station.

??? Step tuning

Press the [~....] or [~] button to manually tune in a station.

Recalling a preset station

A total of 24 preset positions (6-FM1, 6-FM2, 6- FM3, 6-AM) exists to store individual radio stations in memory. Press the corresponding [DIRECT] button or the [.A.] I [T] button to recall the stored radio frequency automatically.

1.Press the [BND] button and select the desired band (FM or AM).

2.Press the corresponding [DIRECT] button or the [.A.] I [T) button to recall the stored station.

Note:

???Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store that station into preset memory.

Manual memory

1.Select the desired station with seek tuning or manual tuning.

2.Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory.

Auto store

Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially. If 6 receivable stations cannot be received, a previously stored station remains unoverwritten at the memory position.

1.Press the [BND] button and select the desired band (FM o.r AM).

2.Press and hold the [~~~] button for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels.

Radio Operations

Preset scan

Preset scan receives the stations stored in preset memory in order. This function is useful when searching for a desired station in memory.

1.Press the [~J~] button.

2.When a desired station is tuned in, press the [~J~ ] button again to continue receiving that station.

Note:

???Be careful not to press and hold the [~J~ J button for 2 seconds or longer, otherwise the auto store function is engaged and the unit starts storing stations.

Instant station recall (lSR)

Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. The ISR function even operates with the unit in other modes.

elSR memory

1.Select the station that you wish to store in ISR memory.

2.Press and hold the [ISR] button for 2 seconds or longer.

e Recalling a station with ISR

In any mode, press the [lSR] button to turn on the radio function and tune the selected radio station. "ISR" appears in the display. Press the [lSR] button again to return to the previous mode.

MP31WMAIAAC

What is MP3?

MP3 is an audio compression method and classified into audio layer 3 of MPEG standards. This audio compression method has penetrated into PC users and become a standard format.

This MP3 features the original audio data compression to about 10 percent of its initial size with a high sound quality. This means that about 10 music CDs can be recorded on a CD-R disc or CD-RW disc to allow a long listening time without having to change CDs.

What is WMA?

WMA is the abbreviation of Windows Media Audio, an audio file format developed by Microsoft Corporation.

Notes:

???If you playa file with DRM (Digital Rights Management) for WMA remaining ON, no audio is output (The WMA indicator blinks).

???Windows Media TM, and the Windows ?? logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.

???To disable DRM (Digital Rights Management)

1.When using Windows Media Player 9/10/11, click on TOOL ~ OPTIONS ~ MUSIC . RECORD tab, then under Recording settings, unclick the Check box for RECORD PROTECTED MUSIC. Then, reconstruct files.

Personally constructed WMA files are used at your own responsibility.

What is AAC?

???AAC is an acronym for uAdvanced Audio Coding" and refers to the audio compression method used with video compression standards MPEG-2 and MPEG-4.

???AAC files composed with the following conditions can be played:

-AAC files encoded with iTunes.

-iTunes Ver. 7.0 or earlier.

-File extension U. m4a" (u.M4A")

???Tracks purchased at an iTunes Music store, and copyright-protected files cannot be played.

???When playing AAC files that include image data, additional time may be required before playback begins.

???Files may not play properly, depending on the iTunes version under which an AAC file is encoded.

Precautions when creating MP31 WMAIAAC file

???Usable sampling rates and bit rates

1.MP3: Sampling rate 8 kHz-48 kHz, Bit rate 8 kbps-320 kbps / VBR

2.WMA: Bit rate 8 kbps-320 kbps

3.AAC: Sampling rate 8 kHz-48 kHz, Bit rate 8 kbps-320 kbps / VBR

???File extensions

1.Always add a file extension u.MP3", u.WMA" or ".M4A" to MP3, WMA or AAC file by using single byte letters. If you add a file extension other than specified or forget to add the file extension, the file cannot be played.

2.Files without MP3IWMAlAAC data will not play. The indication UNO FILE" appears in the play time display if you attempt to play files without MP3IWMAlAAC data.

*When VBR files are played, the play time display may differ the play location.

*When MP3IWMAlAAC files are played, a little no sound part is caused between tunes.

CDIMP31WMAIAAC Operations

???Logical format (File system)

1.When writing MP3IWMAJAAC file on a CD-R disc or CD-RW disc, please select "IS09660 level 1, 2 or JOLIET or Romeo" or APPLE ISO as the writing software format. Normal play may not be possible if the disc is recorded on another format.

2.The folder name and file name can be displayed as the title during MP3IWMAJAAC play but the title must be within 64 single byte alphabetical letters and numerals (including an extension).

3.Do not affix a name to a file inside a folder having the same name.

???Folder structure

1.A disc with a folder having more than 8 hierarchical levels will be impossible.

???Number of files or folders

1.Up to 255 files can be recognized per folder. Up to 510 files can be played.

2.Tracks are played in the order that they were recorded onto a disc. (Tracks might not always be played in the order displayed on the PC.)

3.Some noise may occur depending on the type of encoder software used while recording.

Set the type of file to be played (multi-session function)

When a single disc holds both normal CD type tracks and MP3IWMAJAAC type tracks, use this command to select which type of track to play.

*Default setting is "M-SESS CD".

???When only one type of track (either music CD or MP3IWMAIAAC) is recorded on a disc, selecting either type will allow playback of the disc.

???When playing CCCD (copy-control CDs), set to CD type.

1.Press and hold the [BND] button for 1 second or longer.

Each time the button is held pressed in this way, "M-SESS" will be displayed for 1 second, then "CD" or "MP3" appears in the display, the playback type alternates between CD type and MP3IWMAJAAC type.

??? "M-SESS CD"

When playing music CD only.

??? "M-SESS MP3"

When playing music MP3IWMAJAAC only.

2.When setting is completed, remove the disc and reinsert it.

Disc-In-Play function

As long as the ignition key is turned to the ON or ACC position, this function allows you to turn the power to the unit and start playing the disc automatically when the disc is inserted even if the power is not turned on.

I

???Do not try to put your hand or fingers in the disc insertion slot. Also never insert foreign objects into the slot.

???Do not insert discs where adhesive comes out from cellophane tape or a rental CD label, or discs with marks where cellophane tape or rental CD labels were removed. It may be impossible to extract these discs from the unit and they may cause the unit to break down.

Backup Eject function

Just pressing the [~] button, ejects the disc even if the power to the unit was not turned on.

1.Press the [~l button to eject the CD. Take it out from the ejected position. "EJECT" appears in the display.

Notes:

???If a CD (12 em) is left in the ejected position for 15 seconds, the CD is automatically reloaded (Auto reload).

???If you force a CD into before auto reloading, this can damage the CD.

CDIMP31WMAIAAC Operations

Listening to a disc already loaded in the unit

Press the [SRC] button to select the CD/MP3I WMAlAAC mode.

When the unit enters the CD/MP3/wMAlAAC mode, play starts automatically.

If there is no disc loaded, the indication "NO DISC" appears in the title display.

The mode changes each time the [SRC] button is pressed. (Modes are not displayed for equipment that is not connected.)

Radio (Satellite radio)'"CD/MP3IWMAI AAC USB/MTP/iPod (CD changer) ...

(DVD changer) ... (TV) AUX ... Radio .

Loading a CD

1.Insert a CD into the center of the CD SLOT with the labeled side facing up. "LOADING" appears in the display, the CD enters into the slot, and the play starts.

Notes:

???Never insert foreign objects into the CD SLOT.

???If the CD is not inserted easily, there may be another CD in the mechanism or the unit may

CD-ROMs cannot be played by this unit.

??? Some CDs recorded in CD-RICD-RW mode may not be usable.

Pausing play

1.Press the [~J~] button to pause play. "PAUSE" appears in the display.

2.To resume CD play, press the [~NI~] button again.

Displaying CD titles

This unit can display title data for CD-text/MP3/ WMAlAAC disc and user titles input with this unit.

1.Each time you press the [DISP] button to change the title display.

???CD-TEXT disc

User'"Track'"Disc'"Artist ... User ...

???MP3IWMAlAAC disc

Track'"Folder'"Title'"Album ... Artist ...

Track ...

Notes:

???If the CD playing is not a CD-text CD or no user title has been input, "NO TITLE" appears in the display.

???If MP31WMAIAAC disc is not input TAG, "NO TITLE" appears in the display.

???For MP3, supports 103 Tags V2.3 I 2.2 11.1 11.0.

???Tag displays give priority to V2.3 I 2.2.

???In the case of album Tags for WMA, the information written into the extension header is displayed.

???Only ASCII characters can be displayed in Tags.

Selecting a track

???Track-up

1.Press the [~] button to move ahead to the beginning of the next track.

2.Each time you press the [~] button, the track advances ahead to the beginning of the next track.

???Track-down

1.Press the [~] button to move back to the beginning of the current track.

2.Press the [~] button twice to move back to the beginning of the previous track.

Fast-forwardlfast-backward

???Fast-forward

1.Press and hold the [~] button for 1 second or longer.

???Fast-backward

1.Press and hold the [~] button for 1 second or longer.

*For MP3IWMAJAAC discs, it takes some time until the start of searching and between tracks. In addition, the playing time may have a margin of error.

CDIMP31WMAIAAC Operations

Folder Select

This function allows you to select a folder containing MP3IWMAlAAC files and start playing from the first track in the folder.

1.Press the [T] or [??.] button.

Press the [??.] button to move the next folder. Press the [T] button to move the previous folder.

2.To select a track, press the [........] or [~] button.

Top function

The top function resets the CD player to the first track of the disc. Press the [BND] button to play the first track (track No.1) on the disc.

*In case of MP3IWMAlAAC, the first track of a folder being played will be returned.

Other various play functions

.Scan play

This function allows you to locate and play the first 10 seconds of all the tracks recorded on a disc.

1.Press the [SCN] button to perform scan play.

"SCAN" appears in the display for 2 seconds.

*Scan play starts from the next track after the track currently being played.

???Folder scan play

This function allows you to locate and play the first 10 seconds of the first track of all the folders on an MP3IWMAlAAC disc.

1.Press and hold the [SCN] button for 1 second or longer to perform folder scan play.

"ALL SCAN" appears in the display for 2 seconds.

*Folder scan play starts from the next folder after the folder??currentlybeing played.

??? Repeat play

This function allows you to play the current track repeatedly.

1.Press the [RPT] button to perform repeat play.

"REPEAT" appears in the display for 2 seconds.

??? Folder repeat play

This function allows you to playa track currently being played in the MP3IWMAlAAC folder repeatedly.

1.Press and hold the [RPT] button for 1 second or longer to perform folder repeat play.

"ALL RPT'appears in the display for 2 seconds.

???Random play

This function allows you to play all tracks recorded on a disc in a random order.

1.Press the [ROM] button to perform random play.

"RANDOM" appears in the display for 2 seconds.

???Folder random play

This function allows you to play all the tracks of all the folders recorded on an MP3IWMAlAAC disc in a random order.

1.Press and hold the [ROM] button for 1 second or longer to perform folder random play.

"ALL ROM" appears in the display for 2 seconds.

.To cancel play

1.Press the operating button previously selected.

*The various play mode is canceled and the various playoff mode appears in the display for 2 seconds.

To change adjustment setting

1.Press and hold the [DISP] button for 1 second or longer to switch to the adjustment selection display.

2.Press the [~] or [~] button to select the "item name".

"CLOCK" ~ "SETIINGS" ~ "SCRN SVR" +---+ "MSG INP" +---+ "SCROLL" +--+ "DIMMER" ~ "A-CANCEL" +--+ 'TEL-SP"+---+ "TEL- SW" +--+ "S-CHECK"

3.Press the [.] or [T] button to select the

"desired setting value".

*In the case of display blinking "ENT", you can press the [~~~ 1button to adjust the setting value.

*After completing settings, press the [DISP] button to return to the previous mode.

???Setting the clock

2-1. Select "CLOCK".

3-1. Press the [~~~ ] button

3-2. Press the [~] or [~] button to select the hour or the minute.

3-3. Press the [.] or [T] button to set the correct time.

* The clock is displayed in 12-hour format. 3-4. Press the [~~~] button to store the time into

memory.

Note:

???You cannot set the clock when it is displayed with only the ignition on. If you drain or remove the car's battery or take out this unit, the clock is reset. While setting the clock, if another button or operation is selected, the clock set mode is canceled.

??? Displaying the settings

The number of indicator of this unit decreases, you can see the state of current settings at any operation mode.

2-1. Select "SETIINGS".

3-1. Press the [.] or [T] button to display the state of current settings.

*When the setting is selected, after 1 second the current state will be displayed.

??? Turning the screen saver function on or off

This unit is provided with the screen saver function which allows you to show various kinds of patterns and characters in the operation status indication area of the display in a random order. You can turn on or off this function. If the button operation is performed with the screen saver function on, the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display.

* The factory default setting is "ON". 2-1. Select "SCRN SVR".

3-1. Press the [.] or [T] button to select the setting.

Each time you press the [.] or [T] button, the setting changes in the following order:

"MESSAG~+--+"ON"+--+"OFP

Operations Common to Each Mode

??? Entering message information

Message up to 30 characters long can be stored in memory and displayed as a type of screen saver setting.

*The factory default setting is "WELCOME TO CLARION".

2-1. Select "MSG INP".

3-1. Press the [:-~n button.

3-2. Press and hold the [BND] button for 1 second or longer to clear the old message.

3-3. Press the [~] or [~] button to move the cursor.

3-4. Press the [BND] button to select a character type. Each time you press the [BND] button, the character type changes in the following order:

Capital letters .. Numbers" Symbols ..

Capital letters...

3-5. Press the [A] or [T] button to select the desired character.

3-6. Repeat step 3-3 to 3-5 to enter up to 30 characters for message.

3-7. Press and hold the [:-~~] button for 2 seconds or longer to store the message in memory.

*Press and hold the [BND] button for 1 second or longer to cancel the input message. Then press and hold the [:-~~] button for 2 seconds or longer to store the message and the message return to default setting.

???Setting the method for title scroll

Set how to scroll in CD-TEXT, MP3IWMAlAAC title.

* The factory default setting is "ON". 2-1. Select "SCROLL".

3-1. Press the [A] or [T] button to select "ON" or "OFF".

??? ON:

To scroll automatically.

??? OFF:

To scroll just 1 time.

*When you want to see the title again, in the title mode, press and hold the [DISP] button for 3 seconds or longer to scroll the title.

??? Setting the dimmer control

You can set the dimmer control "ON" or "OFF".

* The factory default setting is "ON". 2-1. Select "DIMMER".

3-1. Press the LA] or [T] button to select "ON" or "OFF".

???Setting the external amplifier

*The factory default setting is "OFF'.

2-1. Select "A-CANCEL".

3-1. Press the [A] or [T] button to select "ON" or "OFF".

??? ON:

Use with connected AMP.

??? OFF:

Use with inside AMP.

???Setting the car speaker output for the cellular phone

*The factory default setting is "RIGHT'.

*To output the telephone calls, set the cellular phone interrupt to "ON".

When the AUX input jack is used to connect an AUX BLUETOOTH BB (BLT370) (sold separately):

2-1. Select'TEL-SP".

3-1. Press the LA.] or [T] button to select "RIGHT'or "LEFT".

??? RIGHT:

Telephone calls can be heard on the front right speaker connected to this unit.

??? LEFT:

Telephone calls can be heard on the front left speaker connected to this unit.

Operations Common to Each Mode

??? Cellular phone interrupt setting

If you connect this unit and your cellular phone with a separately sold cable, you can listen to your telephone calls on your car speakers.

* The factory default setting is "OFF". 2-1. Select "TEL-SW".

3-1. Press the L.A.] or [T] button to select the setting. Each time you press the [.] or [T] button, the setting changes in the following order:

"OFF" <--+ "ON" <--+ "MUTE"

??? OFF:

This unit continues normal operation even when the cellular phone is used.

??? ON:

You can listen to your telephone calls from the speakers connected to this unit.

*When listening to your calls on your car speakers, you can adjust the volume by turning the [ROTARYl knob.

???MUTE:

The sound from this unit is muted during telephone calls.

Note:

???If connecting a hands-free kit, please ensure the setting is ON to receive the telephone audio through the system.

???Performing a system check

This function allows you to perform a system check from the adjust mode when required.

2-1. Select "S-CHECK".

3-1. Press and hold the [:-~n button for 1 second or longer.

"S-CHECK" appears in the display, then the unit returns to the previous operation mode.

Entering titles

Titles up to 8 characters long can be stored in memory and displayed for CD, CD changer, Radio stations and TV stations. The number of titles that can be entered for each mode are as follows.

1.Press the [SRC] button to select the mode you want to enter a title (Radio, CD, CD changer or TV).

2.Select and playa CD in the CD changer or tune in to a TV station or Radio for which you want to enter the title.

3.Press and hold the [DISP] button for 1 second or longer.

4.Press the [~~] or [~] button to select "TITLE IN".

5.Press the [:-~~] button.

The display switches to the title input display.

6.Press the [~....] or [~~] button to move the cursor.

7.Press the [BND] button to select a character type. Each time you press the [BND] button, the character type changes in the following order:

Capital letters ~ Numbers ~ Symbols ~ Capital letters...

8.Press the [.] or [T] button to select the desired character.

9.Repeat steps 6 to 8 to enter up to 8 characters for the title.

10.Press and hold the [:-NI~] button for 2 seconds or longer to store the title into memory.

7. ACCESSORIES

USBIMTP Operations

USB memorylMTP device operation

Note:

???The following operations are the same as for CD mode:

*Pause

* Track selection

*Fast-forwardlfast-backward (Except DRM file)

*Top function

*Scan play

*Repeat play *Random play *Folder selection

See "CDIMP3IWMAlAAC Operations" (page 18- 21) for details.

About USB memory

???USB is an acronym for Universal Serial Bus, and refers to an external bus standard supporting data transfer rates of 12 Mbps.

???This unit is compatible with USB 1.1/2.0 with maximum data transfer rates of 12 Mbps.

???USB memory devices that can be played by connecting to the unit'sUSB cable are limited to those recognized as "USB mass storage class devices"; operation is not guaranteed with all USB memory devices.

*Devices compatible with "USB Mass Storage Class" can be used merely by connecting to the host device. without need for special drivers or application software.

???Consult the manufacturer of your USB memory device for information regarding whether it is supported by "USB Mass Storage Class" standards.

???Audio files playable on this unit are limited to MP3IWMAlAAC files. For details, see the section "MP3IWMAlAAC" (page 18).

???To prevent the accidental loss of data, always back up important data on your computer.

???This unit does not support connections to a computer. In addition, connections made through a USB hub device are also not supported.

???When a USB memory device is composed of two or more drives, only one of the drives will be detected.

???USB memory devices with security functions cannot be played.

???The order in which tracks are recorded may differ depending on the USB memory device connected (the actual playback order may not be the same as that indicated on your computer'sdisplay).

???If you continuously operate folder up/down, the play time keeps as "00:00", and the sound is not emitted.

About USB Digital Media Streaming

This unit supports USB Digital Media Streaming. USB Digital Media Streaming is a function used to play music files transmitted using Media Transfer Protocol (MTP). This function also supports the playback of WMDRM 10 files.

During USB Digital Media Streaming, the unit displays the "MTP" mode indicator.

Use of USB Digital Media Streaming requires the purchase of a supported portable audio player. For information regarding supported portable audio players, consult your nearest Clarion dealer, or visit Clarion'swebsite.

ACAUTION

???Insert and remove a USB memory/MTP device only when the device is not being accessed. Connecting or disconnecting the device at the following times may result in the loss of data:

-If the USB memory/MTP device is removed or power is disconnected during writing to the device.

-When the device is subjected to static electricity or electric noise.

???Do not leave a USB memory/MTP device unattended in an automobile. Exposure to direct sunlight or high temperatures may cause deformation or other malfunction of the USB memory/MTP device.

USBIMTP Operations

Connecting a USB memorylMTP device

1.Connect the USB memory/MTP device to the USB slot.

Playback will begin from the first file recorded on the device.

l:~~~',~.iit~J~i)2:A~&l:??J"-??AUrfQN,;c' '; .,~??n;;,??q

Do not turn on vehicle ignition when the MTP device is connected, since it may result in loss or damage to data on the MTP device.

Connect the MTP device to the USB slot after vehicle ignition is turned on.

Confirm the proper orientation of the connector before inserting.

*If the device is not recognized. press the [SRC] button to switch the source to the device.

*Always insert the device fully into the connector. Incomplete connections may cause the device not to be recognized.

*Depending on the number of tracks recorded, some amount of time may be required until all tracks are read into the unit.

*The order in which tracks are recorded may differ depending on the device connected (the actual playback order may not be the same as that indicated on your computer'sdisplay).

To listen to tracks on a connected USB memorylMTP device

1.Press the [SRC] button to switch the source. When USB memory/MTP device is selected, playback (except DRM files) will begin from the location at which playback was previously stopped.

*When a USB memory/MTP device is connected the USB/MTP mode will be displayed.

*When a USB memory/MTP device is disconnected and then reconnected, playback will begin from the beginning of the USB memory/MTP device.

*When "MTP" mode is selected, AAC files on the MTP device cannot be played.

To stop play

1.Press the [SRC] button and switch the function to a source other than the USB memory.

[??j'~'.)~~~\TI~\~1I~;ijii;,\/~}eAQt'ON~1i;??~}I??i.ri,J~;.??m~1\'ct~i;1

Do not remove the USB memory/MTP device when the USB/MTP mode is selected, since it may result in loss or damage to data on the USB memory/MTP device.

Always backup and save important data on your computer.

2.Remove the USB memory/MTP device from the USB slot.

iPod Operations

This section describes operations when connected to an Apple iPod via the USB slot.

Notes:

???See the iPod Owner's Manual for details regarding operation conditions.

???The unit will not operate, or may operate improperly with unsupported versions.

???For a list of compatible Apple iPod unit with the this model, please contact your Clarion dealer or www.clarion.com.

Connecting an iPod

When an iPod is connected to the USB slot, "Shuffle" set on the iPod will become as follows:

???"Shuffle (Albums)" play ~ Random play

???"Shuffle (Songs)" play ~ All random play

The iPod has two modes, the "Play mode" and the "iPod menu mode" for selecting tracks. Switch between these modes by pressing the [BND] button for 1 second or longer.

Note:

???To connect iPod, please use the USB cable attached in iPod.

Select iPod mode

1.Press the [SRC] button.

Playback will begin from the last file that was played on the iPod.

iPod cable

Confirm the proper orientation of the iPod connector before inserting.

Note:

???The following operations in Play mode operate the same as in CD mode:

*Track selection: [~], [~]

*Fast-forwardlfast-backward: [~<llIII], [~]

*Pause: [~NI~]

*Top function: [BND]

See "CDIMP3IWMAIAAC Operations" (page 18-

21)for details.

Other various play functions (in Play mode)

Notes:

???These functions are not supported when in the iPod menu mode.

???The Random function set on the iPod remains the same after attachment/detachment of the iPod.

???The Repeat function on the iPod will be changed when you connect/disconnect the iPod to the unit.

???Repeat play

Play back one track repeatedly.

1.Press the [RPT] button.

???Random play

Play all albums within a selected category, in random order. (Corresponds to "Shuffle (Albums)" command on iPod.)

1.Press the [ROM] button.

???All random play

Play all tracks within a selected category, in random order. (Corresponds to "Shuffle (Songs)" command on iPod.)

1.Press and hold the [ROM] button for 1 second or longer.

???To cancel play

1.Press the same play button once again.

Notes:

???When the repeat play mode is canceled, after play all tracks within a selected category, playback will begin from the first track in the selected category.

???When playing the last track within a selected category in Random mode, if ACC is switched off then on again, playback will begin from a different track.

???Though the default setting of an iPod is "All Repeat", the indication on the mode status is not displayed.

iPod Operations

Selecting category from the iPod

menu

1.Press and hold the [BND] button for 1 second or longer to select the iPod menu mode.

The iPod menu categories will be displayed.

Notes:

???Repeat and Random mode operations are not supported when in the iPod menu mode.

???In iPod menu mode, if you press the [~]I[~] or [A]I[....] button fast, playback may not be performed.

2.Press the [.] or [T] button to switch between categories.

The iPod menu categories alternate in the following order:

"PLAVLlST" +--+ "ARTIST" +--+ "ALBUM" +--+

"SONG" +--+ "GENRE" +--+ "COMPOSER"...

Note:

The iPod menu mode can be canceled by performing one of the following operations:

???Press the [BND] button.

???When the category select screen is displayed, press the [~] button.

3.Press the [~] button to select the category.

4.When the track name display is showing, press the [~] button.

Playback will begin from the first track in the selected category, and the iPod menu mode will be canceled.

*Subfolders may be displayed, depending on the category.

In this case, use the [A] and [....] buttons to switch between subfolders, then use the [~] button to select the desired subfolder.

*When the track name display is showing, pressing the [~] button will return to the currently playing folder name display.

5.Use the [.] and [T] buttons to select a track within a category.

Selecting category using preset memory

1.Press and hold the [BND] button for 1 second or longer to select the iPod menu mode.

The category can be set as follows in the [DIRECT] (1-6) buttons.

[1]: PLAVLlST

[2]: ARTIST

[3]: ALBUM

[4]: SONG

[5]: GENRE

[6]: COMPOSER

2.Press the desired [DIRECT] (1-6) button to select the category.

* Subfolders may be displayed, depending on

the category.

In this case, use the L.&.] and [....] buttons to switch between subfolders, then use the [~] button to select the desired subfolder.

3.When the track name display is showing, press the [~~] button.

Playback will begin from the first track in the selected category, and the iPod menu mode will be canceled.

*Use the LA.] and [....] buttons to select a track within a category.

About title display

This unit supports the display of title information transmitted from a connected iPod.

???Character code information is UTF-8; displayable characters include English alphanumerics, some symbols, and some umlaut characters.

???Unsupported characters will be replaced by asterisks (*).

Satellite Radio Operations

This function is available when a Satellite Radio Receiver is connected through the CeNET cable.

This unit can control the following satellite radio receivers:

???XM Satellite Interface Adapter (Mini-Tuner Included) : CNP2000UC

Clarion cable for CNP2000UC : CNPCLA1

???SIRIUS Satellite Radio Receiver: SIRCL3

???SIRIUS Satellite Translator Adapter: CLA-SC1 (which needs Sirius universal Tuner sold separately.)

Note:

???When the function is differ depending to the connected receiver, they are distinguished by the following notations:

"XM": for an XM Satellite Radio Receiver

"SIRIUS": for a SIRIUS Satellite Radio Receiver

Selecting a Satellite Radio mode

1.Press the [SRC] button.

The system changes to the specified Satellite Radio mode.

Selecting a band

1. Press the [BND] button to select a band.

This changes the reception band as follows:

??XM:XM1 .. XM2 .. XM3 .. XM1 ...

??SIRIUS: SR1 .. SR2" SR3 .. SR1 ...

???Information displayed during reception

The following information is displayed when the satellite radio cannot be received normally.

???When the receiver is turned on the first time or after a reset: "UPDATING"

???When a channel is being tuned in (no signal is yet received):

XM: "LOADING", SIRIUS: "LINKING"

???A channel without a broadcast has been selected:

XM: "--- CH", SIRIUS: "INVALID CH"

???A channel not covered by your contract: XM: "UPDATING", SIRIUS: "CALL 888" ~ "539-SIRI" (alternated)

Confirming your SIRIUS ID

1.Press and hold the [DISP] button for 1 second or longer to display the ADJUST item.

2.Press the [~] or [~] button to select "SID DISP".

3.Press the [rNI~] button, the display will display the upper 6 digits.

4.Press the LA] or [T] button to switch between the display for the upper 6 digits and lower 6 digits.

5.To return to the previous mode, press the [DISP] button.

Displaying channel labels

1.Press the [D1SP] button to select the desired channel label.

Channel" Category .. Title (Artist) .. Radio text .. Channel. ..

Channel selection

1.Channels are selected with the [~] or [~] button.

*For details, see the following operation descriptions.

Note:

???The audio output is muted and other button operations are not accepted during channel selection.

Tuning mode

There are two channel selection modes: quick tuning mode and step tuning mode.

???Quick tuning

1.Press and hold the [~] or [~] button for 1 second or longer.

???Step tuning

1.Press the [~] or [~] button.

Satellite Radio Operations

Recalling a preset station

A total of 18 satellite radio stations can be stored.

???XM: 6-XM1, 6-XM2 and 6-XM3

???SIRIUS: 6-SR1, 6-SR2 and 6-SR3

This allows you to store your favorite satellite radio stations in memory for later recall.

1.Press the [BND] button to select the desired band.

2.Press the [...] / [..-] button or [DIRECT] button to select the desired preset station.

Preset memory

1.Press the [BND] button to select the desired band.

2.Select the desired channel with quick tuning or step tuning.

3.Press and hold the [DIRECT] button for 2 seconds or longer to store the current channel into preset memory.

Receiving stations selected by category

Satellite Radio allows you to select broadcast channel category (contents).

1.Press and hold the [BND] button for 1 second or longer to select the category selection mode.

*It press once again, return to the channel selection mode.

2.Press the [...] or [..-] button to change the category item.

3.Press the [~] or [~] button to tune in a station.

Notes:

???When the category selection mode is entered, the category of the last received channel is displayed first.

???The category selection mode is canceled when no channel with the selected category can be found.

???The [~J or ~J button are not pressed within 7 seconds, the category selection mode is canceled, and resumes to the channel mode.

Presetting a category

A category can be preset by registering specific categories in [DIRECT] buttons 1 to 6. Then the desired category can be recalled by pressing the corresponding [DIRECT] button.

1.Press and hold the [BND] button for 1 second or longer to enter the category mode.

2.Press the L...] or [..-] button to select a category.

3.Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current category into preset memory.

Notes:

???When the name of a channel stored in memory is changed by a broadcasting channel, the display may show a channel name that differs from the stored name.

???A channel stored in memory may be discontinued at the option of the broadcasting channel.

???If no operation is performed for more than 1 second, category seek tuning can automatically tune in a receivable broadcast channel category.

Scan function

There are two scan modes: the category scan mode and the preset scan mode.

During scanning channels are displayed in abbreviated form, the display mode cannot be switched.

??? Preset scan (PRESET SCN)

A preset scan scans the channels (up to 18 channels) stored in the preset memory about every 10 seconds.

Press and hold the [rrJ~] button for 1 second or longer to select the preset scan mode. And start the preset scanning.

??? Category scan (CAT SCN)

In a category scan, broadcast channels in the same category as the current channel are selected about every 10 seconds.

Press the [rrJ~] button to select the category scan mode. And start the category scanning.

Note:

???Category scanning is not available when no category is defined for the current channel.

CD Changer Operations

Note:

???The following operations are the same as for CD mode:

*Pause

* Track selection *Fast??forwardlfast??backward

*Scan play *Repeat play *Random play

See "CDIMP3IWMAIAAC Operations" (page 18- 21) for details.

CD changer functions

When an optional CD changer is connected through the CeNET cable, this unit controls all CD changer functions. This unit can control a total of 2 changers.

Press the [SRC] button and select the CD changer mode to start play. If 2 CD changers are connected, press the [SRC] button to select the CD changer for play.

*If "NO MAG" appears in the display, insert the magazine into the CD changer. "D??CHECK" appears in the display while the player loads (checks) the magazine.

*If "NO DISC" appears in the display, eject the magazine and insert discs into each slot. Then, reinsert the magazine back into the CD changer.

Note:

???Some CDs recorded in CD-RICD-RW mode may not be usable.

ACAUTIQN

CD-ROM discs cannot be played from every CD changer, it'sdepended on the model.

Displaying CD titles

This unit can display title data for CD-text CDs and user titles input with this unit.

*Title data for CD-text CDs can be displayed with this unit only when it is connected to DCZ625.

1.Press the [DISP] button to change the title display.

Notes:

???If the CD playing is not a CD-text CD or no user title has been input, "NO TITLE" appears in the display.

???If a CD-text CD is not input its disc title or a track title, "NO TITLE" appears in the display.

-

Procedure to scroll a title

Set "SCROLL" to "ON" or "OFF".

(The factory default setting is "ON". Refer to the subsection "Setting the method for title scroll" in section "Operations Common to Each Mode".)

??? When set to "ON"

The title is automatically kept scrolling.

??? When set to "OFF"

To scroll just 1 time.

When you want to see the title again, in the title mode, press and hold the [DISP] button for 3 seconds or longer to scroll the title.

Selecting a CD

1.Press the [.,&.] or [T] button to select the desired disc.

*If a CD is not loaded in a slot of magazine, pressing the [.&.] or [T] button can not work.

Other various play functions

??? Disc scan play

Disc scan play locates and plays the first 10 seconds of the first track on each disc in the currently selected CD changer. This function continues automatically until it is cancelled.

*Disc scan play is useful when you want to select a desired CD.

1.Press and hold the [SeN] button for 1 second or longer. "ALL SCAN" appears in the display and disc scan play starts.

???Disc repeat play

After all the tracks on the current disc have been played, disc repeat play automatically replays the current disc over from the first track. This function continues automatically until it is cancelled.

1.Press and hold the [RPT] button for 1 second or longer. "ALL RPT'appears in the display and disc repeat play starts.

???Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular order. This function continues automatically until it is cancelled.

1.Press and hold the [ROM] button for 1 second or longer. "ALL ROM" appears in the display and disc random play starts.

???To cancel play

1.Press the operating button previously selected.

DVD Changer Operations

By connecting an optional DVD changer that supports CeNET wiring, this unit can be used to control the DVD changer. To view DVDs, an optional monitor is required.

???The DVD control and display functions supported by this unit are limited; the unit does not support all the functions possible on a DVD changer.

For fullest functionality, use the remote control unit provided with your DVD changer to control its operations. For details, consult the Owner'sManual provided with your DVD changer.

Note:

???The following operations are the same as for CD and CD Changer modes:

*Pause

* Track selection

*Fast-forwardlfast-backward

*Scan play

*Repeat play *Random play

See "CDIMP3IWMAIAAC Operations" (page 18- 21) and "CD Changer Operations" (page 32) for details.

TV Operations

Note:

???The following operations are performed the same as for radio mode:

*Channel selection

*Storing channels in memory *Calling channels from memory *Auto store

*Preset scan

See "Radio Operations" (page 16-17) for details.

TV tuner functions

When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions. To watch TV requires a TV tuner and monitor.

Watching a TV

1.Press the [SRC] button and select the TV mode.

2.Press the [BND] button to select the desired TV band (TV1 or TV2). Each time the button is pressed, the input selection toggles between TV1 and TV2.

3.Press the [~] or [~] button to tune in the desired TV station.

Watching a video

The TV tuner has a VTR input terminal to which 1 external device can be connected. Connect a 12 V video cassette player (VCP) or video cassette recorder (VCR) to the TV tuner input terminal.

* The factory default setting is "TV".

1.Press and hold the [DISP] button for 1 second or longer to switch to the adjustment selection display.

2.Press the [~] or [~~] button to select "TV! VTR".

3.Press and hold the [:-J~] button for 1 second or longer to set to "VTR".

4.To return to the TV broadcast, press and hold the [DISP] button for 1 second or longer to switch to the adjustment selection display.

5.Press the [~] or [~~] button to select "TV! VTR".

6.Press and hold the [:-J~] button for 1 second or longer to set to "TV".

Setting the TV diver

You can change the reception setting for the TV antenna connected to the TV tuner.

*The factory default setting is "ON".

1.Press and hold the [DISP] button for 1 second or longer to switch to the adjustment selection display.

2.Press the [~] or [~] button to select "TV DIVER".

3.Press the [A] or [T] button to set to "ON" or "OFF".

??? ON:

Sets the diver setting to ON.

??? OFF:

Sets the diver setting to OFF.

4.Press the [DISP] button to return to the previous mode.

Power does not turn on.

(No sound is produced.)

No sound output when operating

,the unit with

;amplifiers or

-;!

Incorrect wiring.

Power antenna lead is shorted to ground or excessive current is required for remote-on the amplifiers or power antenna.

Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase.

Consult your store of purchase.

1.Turn the unit off.

2.Remove all wires attached to the power antenna lead. Check each wire for a possible short to ground using an ohm meter.

3.Turn the unit back on.

4.Reconnect each amplifier remote wire to the power antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage (excessive current required).

Sound is cut or skipped.

Noise is generated or noise is mixed with sound.

Sound is bad directly after power is turned on.

DCP or main unit connectors Wipe the dirt off with a soft cloth moistened with are dirty.cleaning alcohol.

The speaker protection circuit 1. Turn down sound volume. Function can also be

MP3IWMAJAAC files are not Use MP3IWMAJAAC files encoded properly. encoded properly.

Water droplets may form on Let dry for about 1 hour with the power on. the internal lens when the car

is parked in a humid place.

The device isn't recognized.

The device is damaged. f-C-o-n-n-e-c-to-rs-a-re-Io-o-se-.----l

According to the state of operation on the device, the communication fault is caused.

Disconnect the device and reconnect. If the device is still not recognized, try replacing with a different device.

Disconnect the device and reconnect.

A CD is caught inside the CD deck and is not ejected.

A CD cannot be played due to scratches, etc.

This is a failure of CD deck'smechanism and consult your store of purchase.

Replace with a non-scratched, non-warped-disc.

" ERROR 2A CD inside the CD changer is not loaded.

This is a failure of CD changer'smechanism and consult your store of purchase.

-.f:,

'Ii'

ERROR 3 A DISC cannot be played due to scratches, etc.

Retry or replace with a non-scratched, non-warped- disc.

ERROR 3 ??? The iPod contains no audio

(iPod mode) files.

CUR ERROvercurrent detection.

HUB ERRDo not support the HUB devices.

Insert an iPod containing audio files.

Disconnect the devices and reconnect. If the devices are still not recognized, try replacing with a different devices.

Do not use the HUB devices.

FM Tuner

Frequency Range: 87.9 MHz to 107.9 MHz

Usable Sensitivity: 11 dB~V

50dB Quieting Sensitivity: 17 dB~V

Alternate Channel Selectivity: 60 dB

Stereo Separation (1 kHz): 30 dB

Frequency Response (??3 dB): 30 Hz to 15 kHz

AM Tuner

Frequency Range: 530 kHz to 1710kHz

Usable Sensitivity: 28 dBIJV

CD Player

System: Compact disc digital audio system

Usable Discs: Compact disc

Frequency Response (??1 dB): 20 Hz to 20 kHz

Dynamic Range (1 kHz): 80 dB

Harmonic Distortion: 0.03%

Audio

Maximum Power Output: 200 W (50 W X 4 ch)

Bass Control Action (100 Hz): +14 dB, -14 dB

Treble Control Action (10 kHz): +14 dB, -14 dB

Line Output Level (CD 1 kHz): 2 V

Note:

General

Power Supply Voltage:

14.4 V DC (10.8 to 15.6 V allowable), negative ground

Current Consumption: Less than 15 A

Speaker Impedance: 4 n (4 n to 8 n allowable)

Auto Antenna Rated Current: 500 mA or less

Weight / Source unit: 2.53 lb. (1.14 kg) Weight / Remote control unit:

1.41 oz. (40 g) (including battery) Dimensions / Source unit:

7" (Width) X 2" (Height) X 6-1/8" (Depth) [178 (W) X 50 (H) X 155 (D) mm]

Dimensions / Remote control unit:

1-3/4" (Width) X 4-5/16" (Height) X 7/16" (Depth)

[44 (W) X 113 (H) X 11 (D) mm]

Power Output:

20 W RMS x 4 Channels at 4

and 1 % THD+N

Signal to Noise Ratio:

91 dBA (reference: 1 W into 4 )

All Rights Reserved. Copyright ?? 2007: Clarion Co., Ltd.

PE-30458 280-8584-00

Installation/Wire Connection Guide

Manuel d'installationet de connexion

Guia de instalacion/conexion de cables

mDliEraD ...

-1. BEFORE STARTING / PREPARATIFS / ANTES DE COMENZAR

,

Car battery

Balterie de VOtture

Bateria del autom6vil

Figure 1 / Figure 1 / Figura 1

1.Antes de comenzar, prepare todos los elementos necesarios para instalar la unidad fuente.

2.Instale la unidad con un angulo de 300 sobre el plano horizontal. (Figura 2)

3, Si tiene que realizar cualquier trabajo en la carreceria, como taladrado de orificios, etc., consulte al proveedor de su automovil.

4.Use los tornillos incluidos para la instalacion, EI uso de otres tornillos puede causar danos. (Figura 3)

Chassis??? I ChaSSiS-_-_-I",,",""Chasis Oomm~"0.00

???Universal Mount

1.Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 4,

2.Wire as shown in Section 6.

3, Insert the source unit into the universal mounting bracket until it locks,

4, Take care of the top and bottom of the outer escutcheon and mount it so that all the hooks are locked,

??? Montage universel

Pld(;~' Ie ~up;Jor: 'emontage uni "ersel dans Ie tableau de bord utlliser un tournevis pour replier ers lexteneur chaque languette du support de montage universel pUiS fixer les JangJettes com me montre sur la Figure 4.

2.Cabler com me montre dans la Section 6,

3.Inserer I'appareilpilote dans Ie support de montage unlversel jusqu'a ce qu'ilsoit bloque.

4Reperer Ie haut elle bas de lecusson exteneur et Ie monter de l11anll3re que tous les crochets soient verrouilles,

???Montaje universal

1.Coloque el soporte de montaje universal en el tablero de instrumen- tos, utilice un destornillador para doblar cada reten del soporte de montaje universal hacia adentro, y despues asegure el reten como se muestra en la Figura 4.

2, Conecte los cables como se muestra en la Seccion 6.

3.Inserte la unidad fuente en el soporte de montaje universal hasta que quede enganchado.

4, Tenga cuidado con la partes superior e inferior de la pieza ornamen- tal exterior, y m6ntela de forma que todos los ganchos queden bloqueados,

Notes:

1)Some car models require special mounting kits for proper installation, Consult your Clarion dealer for details.

2)Fasten the front stopper securely to prevent the source unit from coming loose.

???Console opening dimensions

???Dimensions d'ouverturede la console

???Dimensiones de la abertura de la consola

\- 7-3/16" ., (182mm)

Tournevis

Destornillador

Installation direction . /l - ,

Sens d'installation "-r-'

Direcci6n de inslalaci6n

Boltom

Bas

Parte inferior

Outer escutcheon side view

Vue lateraIe de I'ecussonexterieur

Vista lateral de la pieza ornamental exterior

Spring

Ressort

Resorte

??? Fixed Mount

(TOYOTA, NISSAN and other ISO/DIN equipped vehicles)

This unit is designed for fixed installation in the dashboard.

If the vehicle is equipped with a factory-installed radio, install the source unit with the parts and screws marked (*) (Figure 7).

If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the source unit in the following procedure.

Bend the stopper tollowing the procedures below when this source unit is installed to the TOYOTA, NISSAN and other ISOIDIN equipped vehicles.

1. Bend the stopper from the source unit. (Figure 5, 6)

??? Montage fixe

(TOYOTA, NISSAN et autres vehicules equipes ISO/DIN)

Cet apparell est concu pour ene Installation fixe dans Ie tableau de bard Si Ie vellicule est eqJlpe d'unauloradio tnslalle a ruslne, Installer l'appareilpilote avec les pieces et les eerous marquees de i*) (Figure 7).

Sllf''Je.,:culefl'estpas eqJipe d'unauto-radio installe a I uSlne se procurer un kit dmSlalla!;on PV Installer I'apparellp:lote avec la procedure SUlvante

Coubez la outee apres les operations c!~dessous lorsque I'apparellpilote est installl?? sur un vehcule TOYOTA. fSSAN et autres vehlcules eqUipes ISO DIN

1. Coubez la butee de I apparel! source. (Figure 5. 6)

???Montaje fijo

(Automoviles TOYOTA, NISSAN, Y otros provistos

de normas ISO/DIN)

Esta unidad ha sido disenada para instalarse de forma fija en el tablero de instrumentos. Si el autom6vil dispone de una radio instalada en fabrica, instale la unidad luente can las piezas y los tornillos marcados can (*) en la Figura 7.

Si el autom6vil no dispone de una radio instalada en fabrica, adquiera un juego de instalaci6n para instalar la unidad luente de acuerdo con el procedimiento siguiente.

Doble de instalar esta unidad en vehiculos TOYOTA, NISSAN, Y otoros equipados con ISOIDIN, extraiga el reten siguiendo los procedimientos indicados a continuaci6n.

1. Doble el reten procedente de la unidad fuente. (Figura 5, 6)

2.Secure the mounting brackets to the chassis as shown in Figure 7. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other modeis.

3.Wire as shown in Section 8.

4.Secure the unit in the dashboard, and then reassemble the dashboard and the center panel.

Cenler Panel (Nole 1)

Panneau cenlral (Remarqure 1)

Panel central (Nola 1)

;The parts and screws with this mark are used to install radio or included in the installation kit.

*:The screws with this mark are originally attached to the vehicle.

Note 1: In some cases, the center panel may require some modification (trimming, filling, etc.).

Note 2: If a hook on the instal/ation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool.

1.When removing the source unit, disassemble it in the reverse of the order in Section "3. INSTALLING THE SOURCE UNIT".

2.Remove the Detachable Control Panel (DCP).

??? For instructions on removing the DCP, refer to the owner'smanual.

3.Press the outer escutcheon upward and remove it. (Figure 8)

4.Insert and lock the hook plates. (Figure 9)

5.Pull the hook plates to remove the source unit.

???1. Be sure to turn the power off when wiring.

2.Be particularly careful where you route the wires. Keep them well away from the engine, exhaust pipe, etc. Heat may damage the wires.

3.If the fuse should blow, check that the wiring is correct.

If it is, replace the fuse with a new one with the same amperage rating as the original one. (Figure 10)

Note:

There are various types of fuse holder. Do not let the battery side touch other metal parts.

4.Connect the CeNET extension cable fully and securely until it locks. When the CeNET extension cable is pulled, hold the slide cap part and pull it towards you.

???When the CeNET extension cable is extended or branches, use extension cable CCA-520 (2.5m) or CCA-521 (0.6m), or V-adapter CCA-519 (each of them is sold separately).

???Use the CeNET extension cable made by Clarion.

5.When the main power supply fuse in the car is 15 A or less, purchase an automotive cable that can withstand 15 A and supply this unit with power directly from the battery to ensure that the unit will operate normally.

Note that a fuse must be installed at a distance no longer than 30 cm from the cable battery terminal to prevent accidents.

???1 S??assurcrde rnel1re i'apparei!hars Clrcu!t avaflt de falre Ie cab!age .

2.Falre parllcullerernent attention lars de rachemlnernent des fIls.

Les elolgner du motcur. des tuyaux d echappement. etc. La ctlaleur risque d??endonlf11ager ces fils,

3, Slle fUSible saute, verifier si Ie cablage est correct.

SI Ie fusible est grilie. Iepar un fUSible neuf de meme amperage que Ie fUSible d??origine. (Figure

Remarque:

II y a different type de porte?? fusible. La borne du cote batter,e ne doit pas toucher d'autres pieces metailiques.

4. Connecter Ie cable d'extensionCeNET sompletemenl et solide",ent Jusqu'ace qu'llsOIl verroUilie. Pour tirer Ie cable d'extenslonCeNET. len,,!a partie cou!lssante du capuctlOn et tlrer vers vous.AB

Pour etendre au deriver ie cable d'extensionCeNET. utlliser Ie cable d'extensionCCA-S20 (2.5 m 18 pledsll ou CCA-521 10.6m [2 pieds]), ou I'adaptateurY CCA-S t 9 (ces cables sont vendus separemell!) Ut'liselles cables d'exlensionCeNET fabriques par Clanon.

5.SI Ie fUSible d'allmentarionprincipale de la voiture est de 15 A au mains.

achelez un cable automobile qui peut SJpporter 15 A et alimenter cet appareil directement a parllr de la baltene et assurer que l'appareiltoncllonnera normalement.

Notez qu'unfUSible do!~ etre installe a une dIstance de moms 30 em de borne de la batlene pour E!Vlter tout accident.

???1. Antes de hacer las conexiones, asegurese de desconectar la alimentaci6n de la unidad.

2.Sea especialmente cuidadoso al dirigir y fijar los cables. mantengalos alejados del motor, tubo de escape, etc. EI calor puede danar los cables.

3.Si el fusible se quema, revise las conexiones.

Si esta quemado, reemplace el fusible par otro nuevo can el mismo valor de amperaje que el original. (Figura 10)

Nota:

Existen varios tipos de portafusib/es. No permita que el terminal del/ado de Ja bateria toque otras partes metalicas.

4.Conecte el cable prolongador CeNET completa y seguramente hasta que chasquee. Para desconectar el cable, sujete la parte de la tapa deslizable y tire hacia usted.

???Para prolongar a ramificar el cable prolongador CeNET, utilice un cable prolongador CCA-520 (2,5 m) a CCA??521 (0.6 m). a un adaptador en Y CCA- 519 (vendidos aparte).

???Utilice un cable prolongador CeNET labricado por Clarion.

5.Cuando el fusible de alimentaci6n principal del autom6vil sea de 15 A a menos,

adquiera un cable para autom6vil que pueda resistir 15 A Y alimente esta unidad directamente desde la bateria para cerciorarse de que pUeda funcionar normalmente._ Tenga en cuenta que para evitar accidentes, debera instalar un fusible en al cable que va a terminales de la bateria a una distancia no superior a 30 cm.

To external amplifier

* To eliminate audio short circuits, do not remove the caps of unused RCA cables.

CAUTION:Please make sure when connecling external power amplifier, Ihat you properly, 10 the car chassis, ground the amplifier. If this is not done, severe damage 10 Ihe source unil may happen.

Vers un ampJificateur externe

~; Pour suppnmer les courtS-CirCUIts audio, ne pas retirer les capuchons des cables RCA non utilises.

CD

AITENTlON: Lorsque vous raccordez un ampli de puissance externe. faites bien attention a mettre correctement I'amplificateura la masse sur Ie chassis de la voiture. Sinon, VOUS risquez d'endommagergravement I'appareilpilote.

??

??

*RCA

~~~r:r:;f~r~~~~:~~~~~~~Uitosde audio. no quite los casquillos proteetores de los cables RCA no utiliza-

dos. .

PRECAUCION: Cuando conecte un ampliflcador de potencla externo, cerci6rese de ponerio adecuadamente a masa en el chasis de su autom6vll.Si no 10 hiciese, la unidad fuente pOOr(a danarse seriamente.

Antenna

Antenne

Antena

CeNET input ~

Entree CeNET

Entrada de CeNET

W~,-".oro'

Telecommande

Control remota

@

@

??

~

~

1--Fronl RighI

I Avant droit

Delanlero derecho

Fronl Left

Avant gauche Delantero izqulerdo

Rear RighI

Arriere droit

Ef)Gray IJ Gris I Ef)Gris

8GraylBIack I 2Gris nOl'I8Grislnegro

Ef)White I +Blanc I Ef)Blanco

8Whi1e/Black I :;Slanc'nolrI 8Blanco/negro

Ef)Purple I J.: Pourpre I Ef)Purpura

16-Pin Connector Extension Lead

(attached to the source unit)

Fil prolongateur-connecteur 16 broches (attache sur I'appareilpilote)

Cable prolongador de t 6 conlaclos (Iijado a la unidad fuente)

Brown wire (Phone mute lead)*

Fil marron (fil de sourdine de telephonef*

Conductor marr6n (Conductor de sllenclamiento de tehHono)*

Connect to cellular phone mute lead.

Brancher au Iii de sourdine du te!ephone mobile.

Conectelo al conductor de silenciamiento del telefono modular.

Yellow wire (Memory back-up lead)

FII Jaune (fll de soutlen memoire)

Conductor amarillo (Conductor de proteccion de la memoria)

Connect directly to battery.

Note:

Some units do not have connecting leads or jacks. (Refer to *.)

Remarque:

Certams aoparetls n 'one pas de COflOljr~t!tJrs do co,-'r:e~1")1"' Ov ';.::t-- (''''513,'.:

VOjr* .l

Trasero derecho

Rear Left

8Purpie/BIack I S Pourpre noir 18Purpuralnegro

Fuse (15A)

Fusible (15A)

Fusible (15 A)

Brancher directement a la batlene. Conectelo dlrectamente a la bateria.

Nota:

Afgunas unidades no tienen cables de conexi6n ni conectores. (Refierase a *.)

Arriere gauche Trasero Izquierdo

Yellow wire (Bus power lead)*

Fil jaune (fil de bus d'alimentation)*

Conductor amarillO (conductor de allmentaci6n de bus)*

Fuse (3A)

Fusible (3A)

Fusible (3A)

Connect directly to battery.

Brancher directement a la batlerie.

Consctelo directamente a la bateria.

<D REAR RIGHT Black (Red)

RighI

Droit

Derecho

Left

Gauche

Izquierdo

~8WhiteiBIack I C') Blanc/nair 18Blanco/negro (

Ef)Purple l,f. Pourpre I Ef)Purpura

Red wire (Power lead)

Fii rouge {fil d'alimentatlOn)

Conductor rejo (Conductor de alimentacion)

AccessoryE??)12 V

~~~~~~~g;;2vV

BluelWhite wire (Amplifier turn-on lead)

Fil bleu blanc (f'lde mise SOLlS tension tehkommandable de I'amplificateur) Conductor azullblanco (Conductor de conexi6n de la alimentati6n del amplificador)

Connect to remote turn-on lead of amplifier.

Brancher au fIl de mise sous tension telecommandable de I'amplilica:eur.

Conectelo al conductor de conexi6n automatica de la alimentaci6n del amplificador.

Biack wire (Ground lead)

Fil noir IfIi de terre)

Conductor negro (Conductor de puesta amasa)

Connect to vehicle chassis ground.

Brancher a la terre du chassis du vehicule.

Coniletelo a una parte metalica del chasis del vehiculo.

OrangelWhite wire (Illumination lead)

Ftl orange/blanc (fll d'eclairage)

Conductor anaranjado/blanco (conductor de iluminaci6n)

??REAR LEFT Black (White) @ FRONT RIGHT Gray (Red) @ FRONT LEFT Gray (White)

??SUB WOOFER RIGHT Purple (Red)

??SUB WOOFER LEFT Purple (White)

('f) OEM STEERING WHEEL REMOTE CONTROL INPUT JACK (Black)

,)

Connect it to the car power supply terminal lor illumination.

Le connecter a la borne d'alimentalionde I'eclairage de la voiture.

Consctelo al terminal de alimentaci6n dei autom6vit para

iluminacion.

Blue wire (Auto antenna lead)

Fil bleu (fil de I'antenneelectrique)

Conduclor azul (conductor para la antena motorizada)

Connect it to the car power supply terminal for the antenna.

Le connecter a la borne d'alimentatlonde I'antenneelectrique de la voiture.

Conectelo al terminal de alimentacion de la antena.

??TRASERO IZQUIERDO Neqro (Blanco) @ DELANTERO DERECHO Gris (Rojo)

@ DELANTERO IZQUIERDO Gris (Blanco)

??ALTAVOZ DE SUBGRAVES DERECHO Purpura (Rajo)

??ALTAVOZ DE SUBGRAVES IZQUIERDO Purpura (Blanco)

('f) TOMA DE ENTRADA DE CONTROL REMOTO PARA EL VOLANTE OEM (Neara)

??

~-l

--;r-'

frontal para poder escuchar las lIamadas telef6nicas 0 la musica de los dispositivos externos pcr los altavoces del autom6vil.

CD Main unit

??CeNET extension cable

??V-adapter (sold separately) @ CD changer

??DVD chan~er

??RCA extension cable (sold separately)

??Power amplifier (2- or 4-Channel)

??Front speakers

??Rear speakers

@) Monitor

@Satellite radio receiver

@TV tuner module

@5.1 ch surround decoder

@5.1 ch surround decoder control unit

@Optical connector cable

@Center speaker (with amplifier)

??Subwoofer (with amplifier)

@External unit

??Aux Bluetooth BB (BLT370)

??Stereo mini-plug cable (sold separately)

20.Cilble stereo a rnfll-flche (vendu separement)

CD Unidad principal

??Cable prolonaador CeNET

??Adaptador en V (vendido aparte) @ Cambiador de discos compactos

??Cambiadar de DVD

??Cable de extension RCA

??Amplificador de patencia (2 0 4 canales)

??Altavoces delanteros

??Altavaces traseros

@) Monitor

@Receptor de radio via satelite

@Modulo sintanizador de television

@Decodificadar de sonido envolvente Surround de 5.1 canales

@Unidad de control del decodificador de sonido envolvente Surround de 5.1 canales

@Cable con canector optico

@Altavoz central (con amplificadarl

??Altavoz de subaraves (con amplificadorl

@Unidad externa

??Bluetooth BB auxiliar (BLT370)

??Cable de minlclaviia estereo (vendida por separado)

1.Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service center.

2.Use a soft, dry cloth to clean the case. Never use hard cloth, thinner, benzen, alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gentry.

IMPORTANT:

Improper installation may cause damage to your unit or car. If you do not have the appropriate experience, consult a qualified installer. Cutting chassis wire leads voids the warranty.

Ne pas OLJvm Ie coffret Ii n'ya pas de pieces reparables par :'ulilisateLJrit J interieur de I'appareil.SI un objet est tarnbe dans I'appar II pendant !'installation.consulter volie revendeur au un service apres-vente agree CLARION.

2Utillser un cllifton dou~ et sec pour ret oyer Ie coifret, ne Jamals utiliser un chiffon riglde. un diluant du oenzene. de I'alcool.etc. Pour enlever la salete lenace, applique'un peu d'eaufroide ou tiede sur un chiffon doux et essuyer dOL.cemenl la salete

IMPORTANT:

Une /fJstal!alion incorrecte peul endol77mager (apparell ou Ie vehicule. 51 Ion (Ie possede pas les connalssances requises. consuller un 'I;s/allaleur qualifie. Coupel 'e Iii du cN'Issis annule la garamie.

1.No abra la caja. En el interior no hay piezas que pueda reparar el usuario. Si dentro de la unidad entra algo durante la instalaci6n, con suite a su proveedor 0 a un centro de servicio autorizado pcr

CLARION.

2.Para limpiar la caja, utilice un pano suave y seco. no use nunca un pano duro, diluidor de pintura, benceno, alcohol, etc. Para la suciedad resistente, aplique un poco de agua fria 0 caliente a un pano suave y frote suavemente la parte sucia.

/MPORTANTE:

La instalaci6n inapropiada puede causar dafios en su unidad 0 su autom6vif. Si usted no posee la experiencia apropiada, consulte a un insta/ador cualificado. EI corte de los conductores de puesta amasa (carrocerfa) anu/ara /a garantfa.